The chemical characteristics of ashes from cattle, swine and poultry manure

Animal manure is waste that contains large amounts of fertilizer resources. Incineration technology is effective in decreasing the volume of animal manure and concentrating the nutrients. In this study, the nutrient concentration and chemical compounds of several types of animal manure ash were examined to promote their recycling for agriculture. The nutrient concentration of manure ash was dependent on the reduction rate of solid materials by incineration. The phosphorus (P) and potassium (K) of cattle and layer manure were not concentrated greatly because of high silicon (Si) and calcium (Ca) concentrations, respectively. On the other hand, the P concentration of swine manure and broiler litter was increased to 10.1–12.0 % (3.6–4.6 times compared with original materials), equivalent to that of phosphate rock used as fertilizer material. The K concentration of broiler litter ash (16.1 %) was highest of all. The phosphate compounds of cattle and swine manure ashes were determined as Ca₉Fe(PO₄)₇ or Ca₉MgK(PO₄)₇. Hydroxyapatite (Ca₅(PO₄)₃(OH)) was detected in layer manure and broiler litter ashes. By acid treatment of ash, P and K availability of the fertilizer made from layer manure ash (33 % of materials) was equivalent to that of conventional chemical fertilizer.     

Mercury flows in a zinc smelting facility in South Korea

To prepare for the international mercury convention, the characteristics of mercury emissions from a zinc smelting facility in South Korea have been reviewed and a material flow analysis (MFA) has been conducted in this research. As inputs into the mercury MFA study, zinc ores and sulfuric acid were examined, whereas wastewater sludge, effluence water, spent catalyst, and emissions from the casting and roasting processes were examined as outputs. Mercury concentrations extracted from end products like zinc ingots, cadmium ingots, and sulfuric acid were then analyzed. Our results showed that the wastewater sludge discharged from the zinc smelting process had a relatively higher concentration of mercury, indicating that the concentration of mercury was further enriched in the wastewater sludge. The wastes discharged through the zinc smelting process should be thoroughly controlled, as results of the MFA showed that approximately 89 % of the mercury contained in the original input was later found in the waste. According to this study, the higher the concentration of mercury within zinc ores at the input stage, the higher is the mercury concentration found in the wastewater sludge at the output stage.     

Composition and management of rechargeable electric torch wastes in Ibadan,Nigeria

The consumption, disposal, material and chemical compositions of rechargeable electric torch wastes (RETWs) were investigated in Ibadan, Nigeria. Twenty-five RETWs of ten models were collected and disassembled. Their battery electrodes (BEs) and printed circuit boards (PCBs) were acid digested and leached using United States Environmental Protection Agency (USEPA) method 3050B and USEPA Method 1311, respectively. The digests and extracts were analysed for total and extractable Pb, Cd, Cr and Ni using atomic absorption spectrophotometer. The US Test method (CPSC-CH-E 1002-08) was used for digestion of the plastic components. Two hundred questionnaires were distributed to users in Ibadan to determine their usage of RETs and their management when spent. The results indicated that BEs contributed the highest percentage (44 %) component, followed by plastic (38 %). Other components include metal, PCBs, glass and wire. Of the respondents, 61.9 % dispose their spent torches in dumpsites. The mean ± SD concentrations of Pb, Cd, Cr and Ni in the BEs were 500 ± 109 g/kg, 3.94 ± 6.84 mg/kg, 0.33 ± 0.88 mg/kg, 1.68 ± 0.74 mg/kg respectively; in the PCBs, they were 684 ± 42 g/kg, 13.7 ± 17.8 mg/kg, 13.5 ± 10.2 mg/kg and 193 ± 437 mg/kg; and in the plastics, they were 14.1 g/kg, 5.33 mg/kg, 17 mg/kg, and 4.67 mg/kg respectively. The extractable Pb in BE (2670 mg/L) and PCBs (235 mg/L) exceeded the Toxicity Characteristics Leaching Procedure (TCLP) limit of 5 mg/L. RETWs present potential environmental problems in the absence of effective recycling.     

Effects of Starch Sources and Supplementary Materials on Starch Based Foam Trays

Firstly, foam trays were produced from glyoxal cross-linked wheat, potato and corn starches and their mixtures. The most suitable starch type for starch-based foam tray production was selected according to the level of water absorption, density, surface and cross-section micrographs of the foam trays. It was decided that a wheat and potato starch blend was the most suitable starch source for producing the foam trays because they have the lowest water absorption percentage (25.5 ± 0.7%), low density (0.17 ± 0.01 g/cm³) and a smooth surface. Potato–wheat starch foam trays with fibres were produced by adding wheat and wood fibres. Unlike wood fibres addition, wheat fibres significantly decreased the percentage of water absorption (16.63 ± 1.2%) and density (0.115 ± 0.013 g/cm³) of the tray. Also, the trays including wheat fibre had a lighter colour than the wheat–potato starch tray. To further reduce water absorption of the tray, the trays were made by adding two different types of lipids (beeswax or shortening and three different types of filler materials—kaolin, montmorillonite or zinc oxide nanoparticles). According to the level of water absorption of the trays, it was decided that shortening and zinc oxide nanoparticles, in addition to kaolin, were respectively the most suitable lipid and filler materials. The foam trays were produced by adding these supplementary materials. The addition of shortening slightly, zinc oxide nanoparticles moderately and kaolin greatly increased the density of the wheat potato starch tray including fibre. However, the percent of water absorption of the trays containing wheat fibre + shortening or wheat fibre + shortening + zinc oxide nanoparticles decreased 6.4 ± 0.01 and 5.9 ± 0.3%, respectively.     

Scenario analysis for recovery of rare earth elements from end-of-life vehicles

End-of-life vehicles (ELVs) are increasingly being recognized as a possible future resource pool for rare earth elements (REEs). This study provides the amount of REEs that can be recovered from ELVs in Japan based on dismantling survey, chemical identification and substance flow analysis. The REEs were quantified from common passenger vehicles and hybrid electric vehicles. We targeted 17 REEs in estimation of REE contents in ELVs. Four scenarios were developed to explore the recovery of REEs from ELVs. In these scenarios, NiMH batteries and motors containing NdFeB magnets were identified as target components due to they are main REEs carriers; we focused on interpretation of neodymium (Nd) and dysprosium (Dy) owing to they are two of the most critical REEs. The results suggest that 2700 (±500) tons of REEs can be recovered, of which 520 (±100) tons and 31 (±7) tons will be contributed by Nd and Dy in 2030. Meanwhile, the Dy recovered from ELVs can satisfy 23 % (±6 %) of the demand for NdFeB magnets and NiMH battery cells in automobile production of Japan; the Nd recovered from ELVs can satisfy 49 % (±9 %) of the production demands.     

Evaluation of heavy metal content in digestate from batch anaerobic co-digestion of sunflower hulls and poultry manure

In this experimental study, the biogas digestate from mesophilic batch anaerobic co-digestion of poultry manure and an agricultural residue, sunflower hulls, was characterized, particularly in terms of heavy metal content, in order to evaluate whether the biogas digestate was suitable for land applications. Ni, Zn, Cu, Pb, Cr, Cd, and Hg were detected in the biogas digestate in each trial, however, their concentrations were always lower than the limit values stated in Turkish regulations. The main source of heavy metals in the biogas digestate seemed to be the poultry manure, not the agricultural residue. The commercial feedstuffs that are frequently supplemented with various essential elements to promote optimum nutrient supply and optimum growth rates may have contributed to heavy metals presence in the biogas digestate. The results indicated that the biogas digestate from anaerobic co-digestion of manure and agricultural residue could be utilized as fertilizer in agricultural applications.     

Aqueous leaching of cattle manure incineration ash to produce a phosphate enriched fertilizer

Ash produced from the combustion of livestock manure contains large amounts of phosphorus (P), which is an important resource as a fertilizer. Some studies have extracted and recovered P from incinerated biomass ash using inorganic acid or alkaline agents, which produce wastewater that requires treatment and is expensive due to the cost of chemicals. Livestock manure ash contains not only P, but also water soluble salts, which could be a negative influence on plant growth and shall be preferably removed from the recovered fertilizer. In this study, we removed salinity from cattle manure incineration ash by simple aqueous leaching, while retaining the P content. The optimal condition was a 20 min leaching time at a liquid/solid (L/S) ratio of 10 mL g-ash^?1. Under this condition, over 90 % of Cl and 20 % of Na in the original ash was removed, while over 99 % of the P was retained in the leached residue. The leached residue met the fertilizer standard in Japan in terms of citrate soluble fertilizer components and contained few heavy metals. X-ray analyses of the ash indicated that Cl was mainly present as KCl in the original ash, while P was mainly present as Ca compounds in the ash.     

New kinetic modelling parameters for composting process

This study aims to assess the composting process of sawdust, wheat-straw and chicken manure and to define the best blend proportion as a function of organic matter loss. Chicken manure, sawdust, and wheat-straw were mixed at different ratios and composted in reactors. The obtained outcomes revealed that the optimum mixture ratio was found in a mixture of 60 % chicken manure, 30 % sawdust, and 10 % wheat-straw. Three kinetic parameters were used in the models including daily process average temperature, area characterized by temperatures under the process temperature curve, and area characterized by temperatures between the ambient and process temperature (ALAT) as an alternative of process temperature. In addition to these statistical values, modelling efficiency was defined. Statistical analyses revealed that all the evaluated models were found suitable for this study; however, when ALAT was used as a function of temperature, the predictability level of all the models improved.     

Sequential production of pyrolytic oil and biodiesel from oil-bearing biomass

Oil extraction from the oil-bearing biomass and waste materials has been considered as one of the biggest challenges in the biodiesel production process because it has been considered as the most energy- and cost-demanding step. This work provides a promising approach for the direct transformation without oil extraction from calcined montmorillonite clay (CMC) and microalgae by means of the non-catalytic thermo-chemical process in conjunction with the real continuous flow system. The introduced method showed the high tolerance of water, impurities, and free fatty acids (FFAs), which enable the combination of the esterification of FFAs and transesterification of triglycerides into a single step without the lipid extraction. For example, this study showed that the maximum achievable yield of biodiesel via the introduced methodology was 97 ± 0.5 % at the temperature regime of 380–480 °C and this biodiesel yield was enhanced in the presence of CO₂. Thus, the introduced methodology for producing biodiesel could be an alternative way of the methanol liquefaction and transesterification under supercritical conditions.     

Geographic information systems (GIS) based model of dairy manure transportation and application with environmental quality consideration

Survey information was used to develop a minimum cost spatial dairy manure transportation model where environmental quality and crop nutrient requirements were treated as constraints. The GIS model incorporated land use types, exact locations of dairy farms and farmlands, road networks, and distances from each dairy farm to receiving farmlands to identify dairy manure transportation routes that minimized costs relative to environmental and other constraints. Our analyses indicated that the characteristics of dairy manure, its bulk and relatively low primary N, P₂O₅ and K₂O nutrient levels limit the distribution areas or distances between the farms and the land over which the manure can be economically spread. Physical properties of the land limit the quantities of nutrients that can be applied because of excess nutrient buildup in soil and potential to harm nearby waterbodies and downstream people and places. Longer distances between dairy and farmland favor the use of commercial fertilizers due to the high cost of manure transportation. At $0.08 per ton per km transportation cost, the optimal cut-off distances for dairy manure application is 30 km for N and 15 km each for P₂O₅ and K₂O consistent rules. An analysis of dairy manure application to different crop types suggest that, on average, 1 ha of land requires 61 tons of dairy manure to meet the recommended N, P₂O₅ and K₂O needs.     

Composting olive mill pomace and other residues from rural southeastern Spain

The costly disposal of the semisolid residual pomace generated in the two phase extraction used in modern olive mills is causing serious problems to the small oil producers of rural southeastern Spain. Composting may be a viable alternative since complementary residues are usually available in these areas to prepare an adequate starting mixture. In this work, four different combinations of residues (pomace+rabbit manure, pomace+sheep manure, pomace+rabbit manure+rice straw, pomace+rabbit manure+almond shells) were composted in 3 ton piles aerated by turnings, using technology available to any small community of oil producers. During the four long processes (9-10 months), a steady decrease of organic matter and increases in the concentrations of nutrient and humic substances were observed, together with large increases in pH and salinity which may reduce the agronomic value of the final products.     

A simplified material flow analysis employing local expert judgment and its impact on uncertainty

Material flow analysis (MFA) is an effective tool for waste management, but low- and middle-income countries lack essential data for MFA. This study proposed a simplified MFA (sMFA) utilizing local expert judgment (LEJ) and examining the impact of simplification on its uncertainty. A stochastic sMFA model was developed for nitrogen and phosphorus in urban Mandalay, Myanmar. This model was compared with the intensive MFA (iMFA) model employing intensive surveys for primary data collection. For the total loadings to the environment, the medians of the sMFA were higher by 3% and 11%, respectively, for nitrogen and phosphorus than those of the iMFA. The widths of the 80% confidence intervals of these loadings in the sMFA, normalized by those in the iMFA, were − 0.05 and − 0.11, respectively. The three largest flows to the environment were the same for the two models: on-site sanitation effluent/leakage, greywater, and industrial wastewater. Large median gaps between the models were observed for industrial wastewater, fecal sludge, and human excreta, associated with informal waste management, whereby LEJ did not work well. Overall, the sMFA demonstrated a good estimation of nitrogen and phosphorus flows with limited increase of uncertainty, still requiring focused attention on informal waste streams.

Graphical abstract

     

Waste rechargeable electric lamps: characterisation and recovery of lead from their lead-acid batteries

Electrical electronics constitute a significant quantity of municipal solid wastes which are discarded after use in open dumpsites especially in the developing countries. The aim of this study was to characterise the material and chemical components, evaluate current management practices and investigate recovery of lead from battery electrodes (BEs) of waste rechargeable electric lamps (RLs). Twenty-six waste RLs of different models were sampled in Nigeria and characterised. Their BEs were analysed for Pb, Cr, Mn, Cu, Zn, Ni and Fe after acid digestion. Questionnaires were distributed to unselected respondents to assess usage and disposal of the lamps. Reaction of citric acid solutions with Pb in the presence of H₂O₂ was used for the recovery of Pb. 69 % of the respondents disposed their waste RLs in open dumpsites. The mean ± SD concentrations of Pb, Cr, Mn, Cu, Zn, Ni and Fe in the BEs were 600 ± 0.2 g/kg, 65.4 ± 40 mg/kg, 5.05 ± 4.0 mg/kg, 6.81 ± 5.0 mg/kg, 5.98 ± 3.0 mg/kg, 50.0 ± 30 mg/kg and 40.2 ± 35 mg/kg, respectively. The results show that the batteries are lead-acid batteries which require management. At the optimal conditions of S/L = 0.14, temperature = 20 °C and leaching time = 5 h, about 95 % Pb was recovered in form of lead citrate from the battery. High recovery of Pb is possible with simple and environment-friendly reactions.     

Vermistabilization and nutrient enhancement of anaerobic digestate through earthworm species Perionyx excavatus and Perionyx sansibaricus

The aim of the study was to examine safe reuse and recycling of organic waste digestate obtained from a biogas plant (5 % total solid) with enhanced nutrient value through vermitechnology. Two indigenous epigeic earthworm species Perionyx excavates and Perionyx sansibaricus were tried individually for this purpose. The results clearly show a significant increase in pH values from 6.5–7.4, electrical conductivity (21.3–21.7 %), total N (84.5–94.6 %), total P (35.9–47.1 %), total K (49.8–52.6 %), Ca (41.9–41.9 %) and a significant decrease in total organic C (17.1–22.4 %), C/N ratio (7.2–6.9), C/P ratio (20.3–20.6), COD (51.9–55.7 %), BOD (85.5–91.2 %). Similarly, indicator organisms (fecal coliforms and fecal streptococci) showed decrement at the end of the composting period (60 days). Fecal Coliforms reduce to nil, while in fecal streptococci a 6 log reduction was observed. Oxygen uptake rate dropped to 67.4–70 % for vermireactors. Overall, the aforementioned findings highlighted that the indigenous earthworm species could enhance the nutrient value of the anaerobic digestate, which could be utilized as an efficient soil conditioner.     

Grafting of Glycidyl Methacrylate onto Poly(lactide) and Properties of PLA/Starch Blends Compatibilized by the Grafted Copolymer

Poly(lactide)-graft-glycidyl methacrylate (PLA-g-GMA) copolymer was prepared by grafting GMA onto PLA in a batch mixer using benzoyl peroxide as an initiator. The graft content was determined with the ¹H-NMR spectroscopy by calculating the relative area of the characteristic peaks of PLA and GMA. The result shows that the graft content increases from 1.8 to 11.0 wt% as the GMA concentration in the feed varies from 5 to 20 wt%. The PLA/starch blends were prepared by the PLA-g-GMA copolymer as a compatibilizer, and the structure and properties of PLA/starch blends with or without the PLA-g-GMA copolymer were characterized by SEM, DSC, tensile test and medium resistance test. The result shows that the PLA/starch blends without the PLA-g-GMA copolymer show a poor interfacial adhesion and the starch granules are clearly observed, nevertheless the starch granules are better dispersed and covered by PLA when the PLA-g-GMA copolymer as a compatibilizer. The mechanical properties of the PLA/starch blends with the PLA-g-GMA copolymer are obviously improved, such as tensile strength at break increasing from 18.6 ± 3.8 MPa to 29.3 ± 5.8 MPa, tensile modulus from 510 ± 62 MPa to 901 ± 62 MPa and elongation at break from 1.8 ± 0.4 % to 3.4 ± 0.6 %, respectively, for without the PLA-g-GMA copolymer. In addition, the medium resistance of PLA/starch blends with the PLA-g-GMA copolymer was much better than PLA/starch blends.     

Cost Effective Production of Poly-β-Hydroxybutyrate by Bacillus subtilis NG05 Using Sugar Industry Waste Water

The present study describes the treatment of sugar industry waste water and its use as a potential low cost substrate for production of bioplastic by Bacillus subtilis NG05. The B. subtilis NG05 grow at the rate of 0.14 g h^?1 L^?1 of production media used and accumulate the 50.1 % of poly β-hydroxybutyrate (PHB). The phase contrast microscopy revealed the presence of PHB granules in B. subtilis NG05 which was further confirmed by Fourier transform infrared spectroscopy and ¹H-nuclear magnetic resonance. The polymer was further analysed by differential scanning calorimetry. PHB production yield was achieved up to 4.991 g L^?1 with Sugar industry waste water as sole nutrient source. Thus the process provided dual benefits of conversion of a waste material into value added product, PHB and waste management.     

Variability of nitrous oxide and carbon dioxide emissions continuously measured in solid waste incinerators

Nitrous oxide and carbon dioxide were continuously measured and variability of emission factors (EFs) was evaluated in five municipal waste incinerators (MWIs) and four industrial waste incinerators (IWIs) from 24 to 86 days between 2008 and 2011. N₂O EFs were calculated by Monte Carlo simulation and mean N₂O EFs were 7.1, 107, 127, 219 g N₂O/ton waste combusted in MWIs with selective catalytic reduction (SCR) for NOx control, MWIs with selective non-catalytic reduction (SNCR), IWIs with SNCR, and a MWI using fluidized bed with SNCR, respectively. Climate-relevant CO₂ EFs ranged from 0.45 to 0.72 ton CO₂/ton waste combusted in MWIs. Maximum values of upper limit for 95% confidence intervals (CIs) of N₂O EFs estimated in each MWIs with SCR, MWIs with SNCR, IWIs with SNCR were 185, 94, 101% of mean N₂O EFs, respectively. Meanwhile, maximum values of upper limit for 95% CIs of CO₂ EFs were much lower as between 18 and 36% in those facilities. 84% CIs of mean N₂O EFs in MWIs with SNCR and IWIs with SNCR were overlapped indicating those values are not significantly different.     

Comparative fertilizer properties of digestates from mesophilic and thermophilic anaerobic digestion of dairy manure: focusing on plant growth promoting bacteria (PGPB) and environmental risk

The fertilizer properties of anaerobic digestate depend on the feedstock and operating conditions of digestion. In this study, the comparative fertilizer properties of mesophilic and thermophilic digestates from dairy manure were evaluated for plant nutrient contents, and special attention was paid to plant growth promoting bacteria (PGPB). Two digestates contained similar plant nutrient contents, while the thermophilic digestate contained higher contents of NH₄⁺–N. The quantity of Bacillus and Pseudomonas in the mesophilic digestate was significantly higher than in the thermophilic digestate. Furthermore, Bacillus showed siderophore production and antifungal activity (43.5–75.3%), and Pseudomonas showed siderophore and phytohormone production (4.2–75.2 µg ml^?1). One phosphate solubilizing isolate was also detected in the mesophilic digestate. These results indicated that two digestates showed different fertilizer properties with respect to nutrient contents and PGPB, and digestates had the potential to increase the availability of phosphorus and iron in the soil, both to provide phytohormones to plant roots and protect plants from fungal phytopathogens. The contents of indicator bacteria and heavy metals were analyzed to determine their environmental risk, and the results showed a high reduction in indicator bacteria and lower levels of heavy metals than in other feedstocks.     

Evaluation of Extracted Chitosan from Portunus Pelagicus for the Preparation of Chitosan Alginate Blend Scaffolds

In recent years there is a growing need in generating a biocompatible and cost effective porous scaffold for tissue engineering purposes. Therefore, this study focused on conversion of the shell waste of locally available crab variety P.pelagicus (Blue swimming crab) into the chitosan scaffold. As the poor mechanical strength of chitosan limits its usage in tissue engineering, it was blended with alginate. The scaffolds were prepared by the freeze gelation method which requires less time and minimum energy, with fewer residual solvent and easier to scale up. To the best of our knowledge there are no reports on scaffold preparation from the extracted chitosan, blended with alginate by freeze gelation method. The biological properties of chitosan-alginate scaffolds (Cts–Alg) were evaluated and compared with those of chitosan scaffolds. The prepared scaffolds were characterized by SEM, swelling property, in vitro enzymatic degradation, and hemo, biocompatibility properties. Chitosan-alginate scaffolds had an average pore size of 40 μm and tensile strength of 0.564 ± 0.0.018 % MPa. Its swelling ratio was 27.5 ± 0.28 %, with mass loss percentage of 10 ± 0.33 % after 4 weeks of degradation. It has exhibited good hemocompatible properties too. Mouse fibroblast 3T3 cells were able to adhere and proliferate well in the blended scaffold. All these results indicated that chitosan-alginate scaffold is a suitable alternative substitute for tissue engineering.     

Anaerobic co-digestion of dairy cow manure and high concentrated food processing waste

Anaerobic co-digestion of dairy manure (DM) and concentrated food processing wastes (FPW) under thermophilic (55 °C) and mesophilic (35 °C) temperatures, and fertilizer value of the effluent were investigated in this study. Two types of influent feedstock were utilized: 100 % DM and a 7:3 mixture (wet weight basis) of DM and FPW. The contents of the FPW, as feedstock were 3:3:3:1 mixture of cheese whey, animal blood, used cooking oil and residue of fried potato. Four continuous digestion experiments were carried out in 10 L digesters. Co-digestion under thermophilic temperature increased methane production per digester volume. However, co-digestion at 35 °C was inhibited. Total Kjeldahl nitrogen (N) recovered after digestion ranged from 73.1 to 91.9 %, while recoveries of ammonium nitrogen (NH₄-N) exceeded 100 %. The high recovery of NH₄-N was attributed to mineralization of influent organic N. The mixture of DM and FPW showed greater recoveries of NH₄-N after digestion compared to DM only, reflecting its greater organic N degradability. The ratios of extractable to total calcium, phosphorus and magnesium were slightly reduced after digestion. These results indicate that co-digestion of DM and FPW under thermophilic temperature enhances methane production and offers additional benefit of organic fertilizer creation.