Solid recovery rate of food waste recycling in South Korea

Source-separated collection system of household food waste has been implemented national wide in South Korea. Food waste recycling rate that means conversion rate to recycle is over 90 % in present. However, over the value of 90 %, we need to enhance the efficiency of food waste recycling process. We analyzed material flow of 24 food waste recycling facilities and calculated solid recovery rate to key-process. We found that 3–13 % of the solids from food waste outflows with foreign materials and 27–33 % of the solids outflow with wastewater. As a result, solid recovery rates are 65.3, 60.9, and 56.3 % in wet feed facility, dry feed facility, and composting facility, respectively. Alternative ways to recovery solid from wastewater or collection tools to exclude plastic bags, salt, and moisture content are required to make food waste recycling more efficient.     

Optimal design for sustainable development of a material recovery facility in a fast-growing urban setting

Installing material recovery facilities (MRFs) in a solid waste management system could be a feasible alternative to achieve sustainable development goals in urban areas if current household and curbside recycling cannot prove successful in the long run. This paper addresses the optimal site selection and capacity planning for a MRF in conjunction with an optimal shipping strategy of solid waste streams in a multi-district urban region. Screening of material recovery and disposal capacity alternatives can be achieved in terms of economic feasibility, technology limitation, recycling potential, and site availability. The optimization objectives include economic impacts characterized by recycling income and cost components for waste management, while the constraint set consists of mass balance, capacity limitation, recycling limitation, scale economy, conditionality, and relevant screening constraints. A case study for the City of San Antonio, Texas (USA) presents a vivid example where scenario planning demonstrates the robustness and flexibility of this modeling analysis. It proves especially useful when determining MRF ownership structure. Each scenario experiences two case settings: (1) two MRF sites are proposed for selection and (2) a single MRF site is sought. Cost analysis confirms processing fees are not the driving force in the City's operation, but rather shipping cost. Sensitivity analysis solidifies the notion that significant public participation plays the most important role in minimizing solid waste management expenses.     

Options for sustainable industrial waste management toward zero landfill waste in a high-density polyethylene (HDPE) factory in Thailand

The feasibility of the 3R concept tends to increase the reduction, reuse, and recycling of industrial waste. In this study, we investigated the feasibility of 3R methods to cope with industrial waste generated from high-density polyethylene production in Thailand. The sources and types of waste and existing waste management practices were identified. The four sources of waste generation that we identified were: (1) production, (2) packaging, (3) wastewater treatment, and (4) maintenance, distributed as 47, 46, 4, and 3 %, respectively. The main options for management were: sales to recycling plants (60.41 %), reuse and recycling (25.93 %), and industrial-waste landfilling (10.47 %). After 3R options were introduced, the proposed alternatives were found to be capable of reducing the amount of waste by 33.88 %. The results of life-cycle assessment (LCA) were useful for considering the environmental impact where 3R options were adopted. We also found that net greenhouse gas (GHG) emissions and other environmental impacts could be reduced when industrial waste diverted from landfill is used as alternative fuel. However, the cost of waste disposal seems to be the greatest obstacle for the adoption of 3R methods in Thailand.     

Municipal solid waste management in Lahore City District,Pakistan

This study deals with generation, composition, collection, transportation, and disposal, as well as the present cost of the waste management on the basis of 60% collection of the total waste and the cost of proposed improved system of management on the basis of 100% waste collection using the IWM-2 LCI model. A GIS map of Data Ganj Bakhsh Town (DGBT) of Lahore City District showing communal storage facilities is also provided. DGBT has a population of 1,624,169 living in 232,024 dwellings. The total waste generated per year is 500,000 tons, or 0.84/kg/cap/day. Presently 60% of the MSW is collected and disposed in open dumps, while 40% is not collected and lies along roadsides, streets railway lines, depressions, vacant plots, drains, storm drains and open sewers. In DGBT, 129 containers of 5-m³ capacity, 120 containers of 10-m³ capacity and 380 skips of 2.5-m³ capacity are placed for waste collection. The overall collection and disposal cost of the MSW of DGBT is $3,177,900/yr, which is $10.29/ton. Modeling was conducted using the IWM-2 model for improved collection and disposal on the basis of 100% service, compared to the current 60% service. The modelled cost is $8.3/per ton, which is 20% less than the present cost, but the overall cost of 100% collection and disposal increases to $4,155,737/yr.     

Thermo-Chemical Decomposition Study of Polyurethane Elastomer Through Glycerolysis Route with Using Crude and Refined Glycerine as a Transesterification Agent

Due to the increasing amount of polyurethane waste, chemical recycling of these materials is a topic of growing interest for many researchers. The primary purpose of polyurethane feedstock recycling is to recover the starting polyol. In this study glycerolysis using glycerine from two sources and two purity grades is proposed as a method of chemical recycling. The main effort of this paper focuses on the employment of commercial glycerine of analytical grade and waste glycerine without purification derived from the biodiesel production, as a decomposing agent for polyurethane recycling. In this study, the influence of polyurethane to glycerine mass ratio (PU/GL) and the type of decomposing agent on the chemical structure by FTIR, ¹H NMR and GPC was examined. FTIR analysis of the glycerolysates showed absorption peaks similar to the virgin polyol. Those results are in compliance with GPC chromatograms, which showed for all samples, well-defined peak at ca. 13 min of retention time. The molecular weight of glycerolysates was ranging from 800 to 1300 g mol^?1 depending on PU/GL mass ratio. The novel decomposition agent, namely waste glycerine derived from biodiesel production was successfully used in glycerolysis process.     

Potential e-waste generated from households in Indonesia using material flow analysis

Waste of electronic and electrical equipment (e-waste) generated in Indonesia is expected to increase due to high growth of the Indonesian economy and fast development in technology. As Indonesia has not yet had specified criteria on e-waste, in this study, e-waste is defined as any obsolete or unwanted electronic and electrical equipment that is introduced into the recycling and disposal process. The objective of this study is to estimate the e-waste generated in Indonesian households using the method of material flow analysis. The amount of generated e-waste could be used for constructing an e-waste recycling management system in Indonesia. E-waste materials that need to be treated could be known. In this study, some types of equipment, such as television, washing machine, refrigerator, personal computer, and mobile phone, were chosen to be tracers. Using the modified material flow analysis model proposed by Steubing et al. (Waste Manage 30:473–482, 38), the potential e-waste that was generated from households was estimated. The total estimated accumulation of generated e-waste from households in 2015 and 2025 is about 285,000 and 622,000 tonnes, respectively. If a proper recycling system was in place, a new source for valuable materials recovery would be created, as well as protecting the environment and health.     

Waste electrical and electronic equipment (WEEE) management in Korea: generation, collection, and recycling systems

In Korea, generation of waste electrical and electronic equipment (WEEE), or electronic waste (e-waste), has rapidly increased in recent years. The management of WEEE has become a major issue of concern for solid waste communities due to the volumes of waste being generated and the potential environmental impacts associated with the toxic chemicals found in most electronic devices. Special attention must be paid when dealing with WEEE because of toxic materials that it contains (e.g., heavy metals, polybrominated diphenyl ethers, phthalates, and polyvinyl chloride). If managed improperly, the disposal of WEEE can adversely affect the environment and human health. Environmental regulatory agencies; electronic equipment manufacturers, retailers, and recyclers; environmental nongovernmental organizations; and many others are much interested in updated statistics with regard to how much WEEE is generated, stored, recycled, and disposed of. In Korea, an extended producer responsibility policy was introduced in 2003 not only to reduce the amount of electronic products requiring disposal, but also to promote resource recovery from WEEE; the policy currently applies to a total of ten electrical and electronic product categories. This article presents an overview of the current recycling practices and management of electrical and electronic waste in Korea. Specifically, the generation rates, recycling systems and processes, and recent regulations of WEEE are discussed. We estimated that 1 263 000 refrigerators, 701 000 washing machines, 1 181 000 televisions, and 109 000 airconditioning units were retired and handled by the WEEE management system in 2006. More than 40% of the products were collected and recycled by producers. Four major producers’ recycling centers and other WEEE recycling facilities are currently in operation, and these process a large faction of WEEE for the recovery of valuable materials. Much attention should still be paid to pollution prevention and resource conservation with respect to WEEE. Several suggestions are made in order to deal with electronic waste management problems effectively and to prevent potential impacts.     

Cost effectiveness of recycling: A systems model

Financial analytical models of waste management systems have often found that recycling costs exceed direct benefits, and in order to economically justify recycling activities, externalities such as household expenses or environmental impacts must be invoked. Certain more empirically based studies have also found that recycling is more expensive than disposal. Other work, both through models and surveys, have found differently. Here we present an empirical systems model, largely drawn from a suburban Long Island municipality. The model accounts for changes in distribution of effort as recycling tonnages displace disposal tonnages, and the seven different cases examined all show that curbside collection programs that manage up to between 31% and 37% of the waste stream should result in overall system savings. These savings accrue partially because of assumed cost differences in tip fees for recyclables and disposed wastes, and also because recycling can result in a more efficient, cost-effective collection program. These results imply that increases in recycling are justifiable due to cost-savings alone, not on more difficult to measure factors that may not impact program budgets.     

On achieving the state's household recycling target: a case study of Northern New Jersey, USA

In recent times, the State of New Jersey (USA) has been making attempts at promoting recycling as an environmentally friendly means of attaining self-sufficiency at waste disposal, and the state has put in place a 50% recycling target for its municipal solid waste stream. While the environmental benefits of recycling are obvious, a recycling program must be cost effective to ensure its long-term sustainability. In this paper, a linear programming model is developed to examine the current state of recycling in selected counties in Northern New Jersey and assess the needs to achieve the state's recycling goal in these areas. The optimum quantities of waste to be sent to the different waste facilities, which include landfills, incinerators, transfer stations, recycling and composting plants, are determined by the model. The study shows that for these counties, the gap between the current waste practices where the recycling rate stands at 32% and the state's goal can be bridged by more efficient utilization of existing facilities and reasonable investment in expanding those for recycling activities.     

消耗臭氧层物质销毁技术探讨——以天津市废家电拆解企业为例

以天津市消耗臭氧层物质(ODS)销毁示范项目为背景,介绍了天津市废家电拆解企业涉及ODS的回收及处置情况,并参考国内外淘汰ODS处置经验,以含ODS的废冰箱泡棉为例,介绍了较为适用的焚烧处置技术,为后期大量淘汰的ODS物质处置工作提供了技术参考。     

Municipal solid waste management in China: a comparative analysis

This paper illustrates an overview of the past and present MSWM strategies in China. A comparison is made with MSWM in China, and other developed and developing countries to identify and analyze the problems of existing MSWM, and evaluate some effective suggestion to overcome the limitations. Rapid urbanization and economic growth are the main factors of increasing MSW generation in China. The generating MSW has 55.86 % food waste with high moisture contain due to unavailable source separation. Chinese MSWM is dominated by 60.16 % landfilling, whereas incineration, untreated discharge, and other treatments are 29.84, 8.21, and 1.79 %, respectively. In 2014, a total of 604 sanitary landfills, 188 incineration plants, and 26 other units were used for MSWM. With the magnitude of timing, the increasing rate of incineration unit and disposal capacity is higher than the landfill. In 2004–2014, the disposal capacity of landfill and incineration is increased from 68.89 to 107.44 and 4.49 to 53.3 million tons, respectively. However, the heating value in the majority of Chinese incineration plants is 3000–6700 kJ/kg and the inappropriate leachate treatment can be found in 47 % landfill sites. A proper taxation system for MSW disposal is not fully implemented in China, which has a negative impact on overall MSW recycling. From the comparative study of MSWM, it is revealed that the source separation MSW collection, high energy recovery from incineration plants, appropriate leachate treatment, effective landfill location and management, increase waste recycling and proper taxation system for MSW disposal are essential to improve MSWM in China.     

Environmental friendly automated line for recovering the cabinet of waste refrigerator

A large amount of hazardous trichloromonofluoromethane (CFC-11) is contained in the polyurethane (PUR) foam of refrigerator cabinet. How to recover the cabinet of waste refrigerator with environmental awareness has been the pressing problem in the treatment of waste refrigerator. The published literature of waste refrigerator cabinets recovering mainly focuses on policy making and conceptual design. Little information relates to the production line of waste refrigerator cabinet recovering and its detailed operation, which is the urgent needed literature. In this paper, an environmental friendly production line for recovering the cabinet of waste refrigerators was reported for helping enterprise or government to construct line to recover the obsolete refrigerators. It included closed shearing process, activated carbon fiber absorption (ACFA) process, air current separation, and magnetic/eddy current separation. The optimized operating parameters of every process were obtained from the experiments. Then, experiment of recovering 50 waste refrigerator cabinets by the production line was performed in factory. Mass balances of the recovered materials were carried out. The result shown the recovery rate of waste refrigerator cabinet could reach 97.6%. Finally, comparison between the production line and other recovery technologies was made. The results indicated that the proposed line provided environment-friendly recovery of waste refrigerator cabinets while achieving low cost of production.     

The influence of air inflow on CH4 composition ratio in landfill gas

When landfill gas is collected, air inflow into the landfill can reduce CH₄ productivity. The decline of CH₄ content in landfill gas (LFG) negatively affects energy projects. We studied air inflow rates and LFG characteristics from 699 vertical collection facilities (VCFs) in the 2nd landfill at the Sudokwon Landfill in South Korea. We first determined whether or not N₂ was an effective indicator of air inflow at this site using argon assays. The results of this analysis showed that the denitrification processes could be disregarded and that N₂ was an effective indicator of air inflow. Using the composition of N₂ in LFG samples, we found that air inflow occurred at 73.6 % of the VCFs, and 25.6 % of samples from these facilities showed more than 80 vol% of air inflow. In addition, we observed that the O₂ consumption rate was more than 70 % of the volume in all samples. $ R_{{{\text{CH}}_{ 4} }} $ , which is the ratio of CH₄ to the sum of CH₄ and CO₂, decreased with increasing air inflow. Finally, we found that, as air inflow increased, the variation in $ R_{{{\text{CH}}_{ 4} }} $ values for samples with equal air inflow ratios also increased due to differences in air inflow routes.     

Methane production from food waste leachate in laboratory-scale simulated landfill

Due to the prohibition of food waste landfilling in Korea from 2005 and the subsequent ban on the marine disposal of organic sludge, including leachate generated from food waste recycling facilities from 2012, it is urgent to develop an innovative and sustainable disposal strategy that is eco-friendly, yet economically beneficial. In this study, methane production from food waste leachate (FWL) in landfill sites with landfill gas recovery facilities was evaluated in simulated landfill reactors (lysimeters) for a period of 90 d with four different inoculum–substrate ratios (ISRs) on volatile solid (VS) basis. Simultaneous biochemical methane potential batch experiments were also conducted at the same ISRs for 30 d to compare CH₄ yield obtained from lysimeter studies. Under the experimental conditions, a maximum CH₄ yield of 0.272 and 0.294 L/g VS was obtained in the batch and lysimeter studies, respectively, at ISR of 1:1. The biodegradability of FWL in batch and lysimeter experiments at ISR of 1:1 was 64% and 69%, respectively. The calculated data using the modified Gompertz equation for the cumulative CH₄ production showed good agreement with the experimental result obtained from lysimeter study. Based on the results obtained from this study, field-scale pilot test is required to re-evaluate the existing sanitary landfills with efficient leachate collection and gas recovery facilities as engineered bioreactors to treat non-hazardous liquid organic wastes for energy recovery with optimum utilization of facilities.     

Gasification applicability study of polyurethane solid refuse fuel fabricated from electric waste by measuring syngas and nitrogenous pollutant gases

To recycle polyurethane foam waste generated from electric appliance recycling centers for use as fuel in a gasification process, polyurethane solid refuse fuel fabricated as pellets was analyzed for the characteristics of elemental composition, proximate analysis, heating value, and thermo-gravimetric testing. It has a high heating value of 29.06 MJ/kg with a high content of combustibles, which could be feasibly used in any thermal process. However, the nitrogen content, of up to 7 %, was comparably higher than for other fuels such as coal, biomass, and refuse-derived fuel, and may result in the emission of nitrogenous pollutant gases of HCN and NH₃. By conducting gasification experiments on polyurethane solid refuse fuel in a fixed-bed reactor, a syngas with a heating value of 9.76 kJ/m³ and high content of both H₂ and CO were produced with good gasification efficiency; carbon conversion 54 %, and cold gas efficiency 60 %. The nitrogenous pollutant gases in syngas were measured at the concentrations of 160 ppm hydrogen cyanide and 40 ppm ammonia, which may have to be reduced using proper cleaning technologies prior to the commercialization of gasification technology for polyurethane waste.     

Evaluation of environmental impacts of food waste management by material flow analysis (MFA) and life cycle assessment (LCA)

This paper focuses on the evaluation of potential environmental impacts of food waste management practices by material flow analysis (MFA) and life cycle assessment (LCA) during different life cycle stages toward the environmentally sustainable options for Daejeon Metropolitan City (DMC) in Korea. The MFA and LCA studies were conducted to examine different recycling facilities of food waste. The results of the LCA study indicate that, among the different recycling methodologies currently in practice in DMC, Scenario 4 (wet and dry feed site) conduced to higher global warming potential (GWP) and higher acidification potential (AP), whereas Scenarios 2 (wet feed site 1) and 3 (wet feed site 2) resulted in the lowest impact. This is mainly due to the emission caused during the treatment stage. For eutrophication potential (EP), Scenario 1 (composting site) contributed to higher environmental impacts due to the emission of ammonia generated during the treatment process, while in case of photochemical ozone creation potential (POCP), the collection stage for all recycling facilities led to higher impacts to the environment due to the combustion of fossil fuels. This study indicates that the proper disposal of the final residues, such as solid sludge and screened materials, could aid in reducing environmental burdens.     

Analyses of the recycling potential of medical plastic wastes

This study analyzed the recycling potential of plastic wastes generated by health care facilities. For this study, we obtained waste streams and recycling data from five typical city hospitals and medical centers and three animal hospitals in Massachusetts. We analyzed the sources, disposal costs and plastic content of medical wastes, and also determined the components, sources, types and amounts of medical plastic wastes. We then evaluated the recycling potential of plastic wastes produced by general city hospital departments, such as cafeterias, operating rooms, laboratories, emergency rooms, ambulance service and facilities, and animal hospitals. Facilities, laboratories, operating rooms, and cafeterias were identified as major sources of plastic wastes generated by hospitals. It was determined that the recycling potential of plastics generated in hospital cafeterias was much greater than that in other departments. This was mainly due to a very slight chance of contamination or infection and simplification of purchasing plastic components. Finally, we discuss methods to increase the recycling of medical plastic wastes. This study suggests that a classification at waste generating sources, depending upon infection chance and/or plastic component, could be a method for the improved recycling of plastic wastes in hospitals.     

Assessment of solid waste generation and greenhouse gas emission potential in Yangon city,Myanmar

Due to booming economy, growing population and rapid urbanization, solid waste generation in the cities of developing countries has significantly increased. Yangon is the largest and most densely populated city, with over five million residents in Myanmar. Open dumping is the major waste disposal method and recycling sector remains at an early development stage. With increasing waste generation, current waste management activities in Yangon have significant environmental impacts. Therefore, the study developed two linear models to predict annual solid waste generation, regarding per capita waste generation, population growth scenarios, literacy rates and gross domestic products. The Intergovernmental Panel on Climate Change and Institute for Global Environmental Strategies calculation methods were used for greenhouse gas (GHG) emission prediction from recycling, waste transportation and final disposal sites (FDSs). As a result, the total annual waste generation and GHG emission in 2015 may double over the next decade. Two major FDSs, Htawe Chaung and Hteinpin, may contribute waste disposal of 272–797 kilotons per year and emit 177–518 Gg of CO₂-eq per year by 2025. The assessment of annual solid waste generation and GHG emission potential may offer advantages in assisting development of waste management plans in Yangon.     

Production of Poly(l-Lactide)-Degrading Enzyme by Amycolatopsis orientalis ssp. orientalis and Its Catalytic Ability in Biological Recycling of Poly(l-Lactide)

The fermentation conditions for poly(l-lactide) (PLA)-degrading enzyme production by Amycolatopsis orientalis ssp. orientalis were statistically optimized by response surface methodology. The optimal value of the most important factors was 0.39 % PLA and 0.34 % gelatin for 2.81 days of cultivation. Under these conditions, the model predicted a PLA-degrading activity of 155.30 U/l. The verification showed the production amount of 154.2 U/l. The crude enzyme from A. orientalis ssp. orientalis showed potent PLA-degrading ability, which is efficient for the biological recycling of PLA. Up to 4,000 mg/l of PLA granule was completely degraded within 5 days at 45 °C by the crude enzyme. l-lactic acid (600 mg/l) was obtained as a degradation product of PLA after only 2 h of incubation. The results indicated that the crude PLA-degrading enzyme from A. orientalis ssp. orientalis has the potential to degrade PLA to lactic acid for the recycling of PLA industry and waste disposal.     

Approximate cost functions for solid waste treatment facilities.

Cost estimation is a basic requirement for planning municipal solid waste management systems. The variety of organizational, financial and management schemes and the continuously developing technological advancements render the economic analysis a complex task, made more complex by the scarcity of real cost data. The objectives of this paper were: (1) to explore the problems arising in getting cost estimates from scattered and limited published data; (2) to suggest a procedure for generating cost functions relating initial set-up cost and operating cost with facility size; and (3) to present such cost functions, relevant to European states, for selected types of solid waste treatment and disposal facilities. Regarding the problems of available scarce data, one needs to deal with cost figures which correspond to facilities with variations in size, technology, year of construction, working conditions, level of technological automation, environmental impacts, social acceptance, capacity utilization rate, composition of inflowing waste, waste management policies, degree of compliance with quality standards, etc. The paper addresses this issue and discusses the proper use of statistical analyses in such cases of fragmented data; moreover, it points out some usual misuses of statistics by analysts and the danger of getting erroneous results. The suggested process for generating cost functions acceptable to the decision-makers is pivoted around the question of acceptable approximation level. Finally, approximate cost curves are suggested for waste-to-energy facilities, landfilling facilities, anaerobic digestion facilities and composting facilities.