Effect of industrial by-products containing electron acceptors on mitigating methane emission during rice cultivation

Three industrial by-products (fly ash, phosphogypsum and blast furnace slag), were evaluated for their potential re-use as soil amendments to reduce methane (CH₄) emission resulting from rice cultivation. In laboratory incubations, CH₄ production rates from anoxic soil slurries were significantly reduced at amendment levels of 0.5%, 1%, 2% and 5% (wt wt⁻¹), while observed CO₂ production rates were enhanced. The level of suppression in methane production was the highest for phosphogypsum, followed by blast slag and then fly ash. In the greenhouse experiment, CH₄ emission rates from the rice planted potted soils significantly decreased with the increasing levels (2–20 Mg ha⁻¹) of the selected amendments applied, while rice yield simultaneously increased compared to the control treatment. At 10 Mg ha⁻¹ application level of the amendments, total seasonal CH₄ emissions were reduced by 20%, 27% and 25%, while rice grain yields were increased by 17%, 15% and 23% over the control with fly ash, phosphogypsum, and blast slag amendments, respectively. The suppression of CH₄ production rates as well as total seasonal CH₄ flux could be due to the increased concentrations of active iron, free iron, manganese oxides, and sulfate in the amended soil, which acted as electron acceptors and controlled methanogens’ activity by limiting substrates availability. Among the amendments, blast furnace slag and fly ash contributed mainly to improve the soil nutrients balance and increased the soil pH level towards neutral point, but soil acidity was developed with phosphogypsum application. Conclusively, blast slag among the selected amendments would be a suitable soil amendment for reducing CH₄ emissions as well as sustaining rice productivity.     

Briquetting of charcoal from sugar-cane bagasse fly ash (scbfa) as an alternative fuel

Brazil is the largest worldwide producer of alcohol and sugar from sugar-cane and has an extensive alternative program for car fuel which is unique. The objective of this work is to offer one management option of a solid residue produced by this industrial segment. The pressed sugar-cane bagasse is burned to produce steam and electricity by cogeneration. The combustion yields both bottom and fly ashes which contain high amounts of silicon oxide as a major component. Fly ash which contains a high volume (>30% by weight) of charcoal was used in this work. The ash was sieved to separate the thick charcoal from inorganic materials which are concentrated in the thinner fraction. The briquettes were hand pressed using charcoal mixed with a binder (starch) obtained from cassava flour (a tropical root). The results (density, mechanical resistance) obtained with 8% by weight of starch binder are presented here. Thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) were used to characterize the ashes and the briquettes. The results show that sugar-cane bagasse fly ash (SCBFA) can be used to produce briquettes with an average density of 1.12 g cm^?3 and an average calorific value of 25,551 kJ/kg.     

Biodegradable Corn Starch Loose-Fill. II. The Effect of Storage at Different Relative Humidities on the Physical Properties of Loose-Fill

The physical properties of corn starch loose-fill were examined at various relative humidities (r.h.). After 48 h of storage at both 25 and 50% r.h., only a slight change in the dimension and physical properties of the corn starch loose-fill was apparent. A wet environment (75% r.h. for 48 h), however, caused significant shrinkage and the loss of physical properties. The tensile properties, particularly tensile modulus, sharply increased, while the resilience gradually decreased with storage time. Amorphous X-ray diffraction patterns of corn starch loose-fills were transformed into crystalline patterns due to aging at 75% r.h. after 48 h. These changes were attributed to the structural relaxation, which was accelerated by moisture gain. The T _g of corn starch loose-fill decreased with increasing the moisture content in expanded starch. Our proposed model based on Avrami equation was able to describe the time-dependent recrystallization of corn starch by modifying the time-dependent tensile modulus. The growth parameter (n) and time constant (k) for the recrystallization process of corn starch loose-fill were about 3.2 and 8.87 × 10^–18 s^–1, respectively. If the growth parameter of 3.2 is considered, spherulitic growth of crystallization occurred in the corn starch loose-fill in the wet environment.     

Preparation and characterization of sorbents prepared from ash (waste material) for sulfur dioxide (SO2) removal

Sorbents synthesized from various types of ash (coal fly ash, coal bottom ash, oil palm ash, and incinerator ash) for flue gas desulfurization were investigated. The sorbents were prepared by mixing the ashes with calcium oxide and calcium sulfate using the water hydration method. The effects of various sorbent preparation variables, such as the hydration period, the ratio of calcium oxide to ash, and the amount of calcium sulfate, on the Brunauer-Emmett-Teller (BET)-specific surface area of the resulting sorbent were studied using a two-level full factorial design. The surface area of the sorbents obtained range from 15.4 to 122.1m²/g. Regression models were developed to correlate the significant variables to the surface area of the sorbents. An analysis of variance (ANOVA) showed that the model was significant at a confidence level of 95%. It was found that apart from all the individual variables studied, interactions between variables also exerted a significant influence on the surface area of the sorbent. From the activity test results, it was found that sorbents prepared from coal fly ash and oil palm ash have the highest SO₂ absorption capacity. Scanning electron microscope (SEM) analysis showed that the sorbent was composed of a compound with a high structural porosity, while an X-ray diffraction spectrum showed that calcium aluminum silicate hydrate compounds are the main products of the hydration reaction.     

Influence of flue-gas desulfurization systems on coal combustion by-product quality at kentucky power stations burning high-sulfur coal

Two Kentucky power plants burning similar blends of high-sulfur western Kentucky and southern Indiana coal provide a unique opportunity to examine the variations in coal combustion by-products due to differences in the method of wet flue-gas desulfurization (FGD). One plant employed carbide lime-based scrubbing for two units and a dual-alkali process for the third unit. The second plant employed a Mississippian limestone from Kentucky for all four units. This study provides an example of optical and SEM petrographic techniques, supplemented by chemical analyses, applied to the study of, at least from the geologic perspective, non-traditional materials. The coal sources comprise a blend of high volatile C and B bituminous, high vitrinite (85–90%, mmf), high-sulfur (> 3%, dry) coals. The fly ash is dominated by glassy phases (70–80%) with about 5–10% spinel (predominately magnetite), 3–10% quartz, and 4–10% isotropic coke comprising the remaining portion of the ash. SEM observations indicate that the glassy particles exhibit a bimodal size distribution with sub-micron glass spheres and a population of larger (several 10s of microns) spheres. The bottom ash has higher proportions of spinels and mullite, with negligible carbon forms, compared to the fly ash from the same units. Fly ashes were observed to be lower in Fe and higher in Al, Si, and S compared to the bottom ashes. Carbide lime, a by-product of acetylene manufacture, soda ash, and limestone were the reagents used in the flue-gas desulfurization processes. The primary FGD by-product is a calcium sulfite slurry which is vacuum filtered and mixed with fly ash and, usually, lime, to form a stable product for disposal. The FGD by-products have some potential, as yet unrealized, for utilization.     

Investigation of hydrogen generation from municipal solid waste incineration fly ash

Hydrogen generation from municipal solid waste incineration fly ash was investigated to understand the influences of contacting method, kinds of contact solution, liquid to solid ratio, and particle size distribution of materials. Redox properties of materials and hydrogen generation were also studied. The largest quantity of gas generated in contact with water was 29.1 ml/g-ash, most of which was hydrogen. Fluidized bed fly ash generated more gas than stoker fly ash. In order to calculate the hydrogen generation potential (the maximum quantity of gas generated in contact with water), a novel system using a Y-shaped test tube and NaOH was utilized. This method gives values which are related to the quantity of generated gas in contact with water. A relationship between the aluminum content and hydrogen generation potential was observed, especially for fluidized bed fly ash. The reducing potential of fluidized bed fly ash was higher than that of stoker fly ash. Only fluidized bed fly ash showed a positive correlation between aluminum content and reducing potential, and between reducing potential and hydrogen generation potential. These results suggest that fluidized bed fly ash contains more Al⁰ than stoker fly ash. Received: September 11, 1998 / Accepted: March 19, 1999     

Removal of carbon constituents from hospital solid waste incinerator fly ash by column flotation

Hospital solid waste incinerator (HSWI) fly ash contains a large number of carbon constituents including powder activated carbon and unburned carbon, which are the major source of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) in fly ash. Therefore, the removal of carbon constituents could reduce PCDD/Fs in fly ash greatly. In this study, the effects of the main flotation parameters on the removal of carbon constituents were investigated, and the characteristics of the final product were evaluated. The results showed that loss on ignition (LOI) of fly ash increased from 11.1% to 31.6% during conditioning process. By optimizing the flotation parameters at slurry concentration 0.05 kg/l, kerosene dosage 12 kg/t, frother dosage 3 kg/t and air flow rate 0.06 m³/h, 92.7% of the carbon constituents were removed from the raw fly ash. Under these conditions, the froth product has LOI of 56.35% and calorific values of 12.5 MJ/kg, LOI in the tailings was below 5%, and the total toxic equivalent (TEQ) of PCDD/Fs decreased from 5.61 ng-TEQ/g in the raw fly ash to 1.47 ng-TEQ/g in the tailings. The results show that column flotation is a potential technology for simultaneous separation of carbon constituents and PCDD/Fs from HSWI fly ash.     

An examination of the exothermic nature of fluidized bed combustion (FBC) residues

Circulating fluidized bed combustion (CFBC) ashes from nine operational periods at the 183 MWe CFBC boiler at Point Aconi were examined for exothermic behaviour. Bed ashes and fly ashes were investigated using a Parr 1455 solution calorimeter. Limited tests were also carried out with additional samples from Point Aconi and from the 160 MWe TVA Bubbling Fluidized Bed Combustion boiler to evaluate the effects of particle size and aging on exothermic behaviour. For the Point Aconi ashes, heat release from the bed ash ranged from 11 to 52 J/g, and the maximum heat release rates ranged from 0.06 to 0.17 J/g/s. For the fly ash heat release varied from 114 to 187 J/g and the maximum heat release rates ranged from 0.8 to 1.9 J/g/s. In the fly ash samples, 50% or more of available CaO was converted to Ca(OH)₂, while for the bed ash a third or less of the CaO was converted to Ca(OH)₂. The exothermicity of the bed ash is directly proportional to the CaO content of the ash. However, this is not true for the fly ash. The exothermic behaviour of fresh FBC ash appeared to be greatly reduced by exposure in air over a 48-h period. Another conclusion of this work is that particle size effects the exothermic behaviour.     

Synthesis of zeolite from Italian coal fly ash: Differences in crystallization temperature using seawater instead of distilled water

In this study Italian coal fly ash was converted into several types of zeolite in laboratory experiments with temperatures of crystallization ranging from 35 up to 90 °C. Distilled and seawater were used during the hydrothermal synthesis process in separate experiments, after a pre-treatment fusion with NaOH.The results indicate that zeolites could be formed from different kind of Italian coal fly ash at low temperature of crystallization using both distilled and seawater. SEM data and the powder patterns of X-ray diffraction analysis show that faujasite, zeolite ZK-5 and sodalite were synthesized when using both distilled and seawater; zeolite A crystallized only using distilled water. In particular the experiments indicate that the synthesis of zeolite X and zeolite ZK-5 takes place at lower temperatures when using seawater (35 and 45 °C, respectively). The formation of sodalite is always competitive with zeolite X which shows a metastable behaviour at higher temperatures (70–90 °C).The chemical composition of the fly ash source could be responsible of the differences on the starting time of synthesized zeolite with distilled water, in any case our data show that the formation of specific zeolites takes place always at lower temperatures when using seawater.     

REVEGETATION OF WASTE FLY ASH LAGOONS II. SEEDLING TRANSPLANTS AND PLANT NUTRITION

As an alternative or in addition to direct seeding, container-grown transplants provide a means of economically and rapidly revegetating waste fly ash lagoons through the expeditious establishment of vegetation islands. Survival and growth ofEnchylaena tomentosaandNitraria billardiereitransplants were largely dependent on the size of the root volume at transplanting. Growth response of both species in fly ash increased significantly as transplant container size increased from 110 ml to 800 ml. Fly ash incorporated into the potting mix during the containerised stage of growth generally reduced plant growth and survival following eventual transplantation. Gradual hardening ofEnchylaena tomentosaseedlings to increasing concentrations of fly ash in the potting mix (25 to 50 to 75% fly ash), however, improved immediate survival following transplantation, into pure ash. Nitrogen deficiency in Port Augusta fly ash was a major nutritional limitation to growth of these two species. Growth and dry matter production responded optimally to application of N fertiliser (NH₄NO₃) at 100–150 kg N ha⁻¹. Although bicarbonate-extractable P levels in fly ash were high (over 250 mg kg⁻¹), a response ofEnchylaena tomentosato supplementary P application [Ca(H₂PO₄)₂.H₂O] at 100–200 kg P ha⁻¹was observed.N. billardiereidid not respond to supplementary P, and it was suggested that fly ash P may be selectively available to plants on a species dependent basis. No growth responses to K application (KCl) at rates of up to 400 kg K ha⁻¹were found.     

Coal fly ash based carbons for SO2 removal from flue gases

Two different coal fly ashes coming from the burning of two coals of different rank have been used as a precursor for the preparation of steam activated carbons. The performance of these activated carbons in the SO₂ removal was evaluated at flue gas conditions (100 °C, 1000 ppmv SO₂, 5% O₂, 6% H₂O). Different techniques were used to determine the physical and chemical characteristics of the samples in order to explain the differences found in their behaviour. A superior SO₂ removal capacity was shown by the activated carbon obtained using the fly ash coming from a subbituminous–lignite blend. Experimental results indicated that the presence of higher amount of certain metallic oxides (Ca, Fe) in the carbon-rich fraction of this fly ash probably has promoted a deeper gasification in the activation with steam. A more suitable surface chemistry and textural properties have been obtained in this case which explains the higher efficiency shown by this sample in the SO₂ removal.     

Dialdehyde starch and zein plastic: Mechanical properties and biodegradability

Dialdehyde starch (DAS) and zein, a hydrophobic corn protein, were investigated to produce biodegradable plastics with improved water resistance and mechanical properties. In the study, dialdehyde starch and zein ratio, plasticizers, and degree of starch oxidation were examined. Increased molding temperature and level of starch oxidation decreased water absorption of the plastic. Tensile strength and Young's modulus increased with starch oxidation. The biodegradation of starting materials and ground plastic specimens was studied in aerobic soil reactors maintained at 25°C for 180 days. Biodegradation of corn starch, zein, and dialdehyde starch for 180 days produced CO₂ equivalent to 64, 63, and 10% of theoretical carbon, respectively. Specimens of molded DAS and zein (3 : 1) plastic showed accelerated CO₂ evolution compared to DAS and other raw materials alone. By 180 days, specimens made with starch of low oxidation (1 and 5% oxidized) demonstrated a 60% biodegradation, and specimens with highly oxidized starch (90% oxidized) achieved 37% biodegradation.Paper presented at the Bio/Environmentally Degradable Polymer Society—Third National Meeting, June 6–8, 1994, Boston, Massachusetts.Journal Paper J-15927 of the Iowa Agriculture and Home Economics Experiment Station, Ames, Project No. 3258.     

Investigation of gamma ray absorption levels of composites produced from copper mine tailings,fly ash,and brick dust

To date, heavyweight concretes have been produced from various heavy aggregates as radiation insulation materials, and their gamma ray absorption levels have been investigated. Many of the studies have used heavy aggregates instead of cement or coarse aggregates from composite material components. The present study prepared lightweight concretes using copper mine tailings, clay brick dust, and fly ash instead of fine aggregates. Some mechanical tests (density, compressive strength, and ultrasonic pulse velocity) were performed on composite blocks with dimensions of 5*5*5 cm, and radiation interaction parameters [linear absorption coefficient (cm⁻¹), mass attenuation coefficient (cm²/gr), HVL (half-value layer) (cm), MFP (cm), and permeability (%)] were measured. Radiation interaction parameters were obtained using a HPGe gamma detector. Radiation measurements were performed at five different photon energies: 583 keV (¹³³Ba), 609 keV (¹³³Ba), 662 keV (¹³⁷Cs), 911 keV (133^Ba), 1173 keV (⁶⁰Co), and 1332 keV (⁶⁰Co). Additionally, the compressive strength and UPV values of composite materials were associated with their gamma ray permeability. Tests revealed that samples with the addition of copper mine tailings yielded the best energy absorption at all energy levels and that absorption decreased as the energy level increased. For example, with the increasing of the energy level, mass attenuation coefficients decreased. The highest mass attenuation coefficients were obtained as 0.128 cm²/g at an energy level of 583 keV in composites produced from copper mine tailings. On the other hand, it was measured at the same energy level as 0.069 cm²/g (a 46% decrease) in the composites produced with fly ash. In addition, it was observed that fly ash used as a fine aggregate did not have a significant effect on mass attenuation coefficient and could be used as a gamma shield if the material thickness was increased to an average of 14 cm. This study revealed that tailings materials could be used as radiation shields. This study also demonstrated that not using heavy aggregates and producing lightweight concrete in radiation shield production significantly reduced shield production cost.

     

钛硅分子筛催化双氧水氧化水中间甲酚

探索催化双氧水氧化去除间甲酚对开发炼油厂碱渣废水处理新技术意义重大。采用钛硅分子筛催化双氧水氧化水中间甲酚,考察了反应时间、反应温度、双氧水加入量、催化剂加入量和初始溶液pH对间甲酚去除率的影响。实验结果表明：钛硅分子筛对双氧水氧化间甲酚具有显著的催化作用;在反应时间为90 min、反应温度为80 ℃、n（H₂O₂）∶n（间甲酚）为4、催化剂加入量为1.5 g/L、初始溶液pH为1.0~11.0的条件下,间甲酚去除率约为94%,间甲酚溶液的BOD₅/COD从氧化前的0.26提高到氧化后的0.38,可生化性显著提高。     

High fire resistance in blocks containing coal combustion fly ashes and bottom ash

Fire resistance recycled blocks, containing fly ash and bottom ash from coal combustion power plants with a high fire resistance, are studied in this paper by testing different compositions using Portland cement type II, sand, coarse aggregate and fly ash (up to 50% of total weight) and bottom ash (up to 30% of total weight). The fire resistance, physical-chemical (density, pH, humidity, and water absorption capacity), mechanical (compressive and flexural strength), and leaching properties are measured on blocks made with different proportions of fly ash and bottom ash. The standard fire resistance test is reproduced on 28 cm-high, 18 cm-wide and 3 cm-thick units, and is measured as the time needed to reach a temperature of 180 °C on the non-exposed surface of the blocks for the different compositions.The results show that the replacement of fine aggregate with fly ash and of coarse aggregate with bottom ash have a remarkable influence on fire resistance and cause no detriment to the mechanical properties of the product. Additionally, according to the leaching tests, no environmental problems have been detected in the product. These results lead to an analysis of the recycling possibilities of these by-products in useful construction applications for the passive protection against fire.     

The effect of the addition of fly ash to municipal digested sludge on its electroosmotic dewatering

Effective handling of municipal digested sludge requires that the product cake have low water content. To this end, we investigated the change in sludge dewaterability after the addition of fly ash to municipal digested sludge, dewatering of which is difficult because of its high organic content. The performance of the dewatering is compared with that of electroosmotic dewatering (EDW) and conventional mechanical dewatering (CMD). Fly ash classified by sieving to the size of 25–75 μm and >75 μm is added to the municipal digested sludge by 10, 20, and 50 wt% by wet base. When adding fly ash particles to municipal digested sludge, dewatering efficiency improved with smaller fly ash particle size and with increase in the amount. When sludge was dewatered using an electroosmotic dewatering method, the dewatering efficiency is improved about 40% by adding fly ash of 25–75 μm particle size with 20 wt% when compared with conventional mechanical dewatering method without adding the fly ash. It is concluded that fly ash particles rich in inorganic material are helpful in the dewatering process when added to municipal digested sludge and EDW is more effective than CDW.     

Effect of unburned carbon on lead, zinc, and copper recovery from molten fly ash by chloride-induced volatilization

The present work focuses on investigation of the effective recovery of heavy metals from molten fly ash by applying chloride-induced volatilization. In particular, the effect of unburned carbon on the chloride-induced volatilization of lead, zinc, and copper from model and real molten fly ashes was investigated in the temperature range 873–1173 K under a N₂ atmosphere. As a result, almost 100% of lead and a significant proportion of zinc were volatilized from the real molten fly ash samples at 1173 K. In contrast, for the model fly ash, volatilization ratios of lead and zinc at 1173 K were only 85% and 25%, respectively. Further, the results of X-ray diffraction analysis suggested that PbO in molten fly ash was converted either to Pb₂OCl₂ or Pb by respective chlorination and reduction reactions. Meanwhile ZnO and CuO in the molten fly ash were reduced to Zn and Cu by reaction with unburned carbon. Subsequently, Pb, Zn, and Pb₂OCl₂ were volatilized, but Cu remained in the solid residue. Finally, the volatilization ratio of zinc increased with the addition of carbon, and more than 98% of zinc was volatilized at 1173 K from a fly ash with a carbon content of 20%.     

A study of disposed fly ash from landfill to replace Portland cement

The landfills of fly ash are the problem of all power plants because this disposed fly ash is not used in any work. This research studies the potential of using disposed fly ashes which have disposal time of 6-24 months from the landfill of Mae Moh power plants in Thailand to replace Portland cement type I. Median particle sizes of disposed fly ashes between 55.4 and 99.3 microm were ground to reduce the sizes to about 7.1-8.4 microm. Both original and ground disposed fly ashes were investigated on physical and chemical properties. Compressive strengths of disposed fly ash mortars were determined when Portland cement type I was replaced by disposed fly ashes at the rate of 10%, 20%, and 30% by weight of cementitious material (Portland cement type I and disposed fly ash). The results presented that most particles of original disposed fly ashes were solid and sphere with some irregular shape while those of ground disposed fly ashes were solid and irregular shape. CaO and LOI contents of disposed fly ashes with different disposal times had high variation. The compressive strengths of original disposed fly ash mortars were low but those of ground disposed fly ash mortars at the age of 7 days were higher than 75% of the standard mortar and increased to be higher than 100% after 60 days. From the results, it could be concluded that ground disposed fly ashes were excellent pozzolanic materials and could be used as a partial replacement of cement in concrete, even though they were exposed to the weather for 24 months.     

Flue gas desulfurization gypsum and coal fly ash as basic components of prefabricated building materials

The manufacture of prefabricated building materials containing binding products such as ettringite (6CaO·Al₂O₃·3SO₃·32H₂O) and calcium silicate hydrate (CSH) can give, in addition to other well-defined industrial activities, the opportunity of using wastes and by-products as raw materials, thus contributing to further saving of natural resources and protection of the environment.Two ternary mixtures, composed by 40% flue gas desulfurization (FGD) gypsum or natural gypsum (as a reference material), 35% calcium hydroxide and 25% coal fly ash, were submitted to laboratory hydrothermal treatments carried out within time and temperature ranges of 2 h–7 days and 55–85 °C, respectively. The formation of (i) ettringite, by hydration of calcium sulfate given by FGD or natural gypsum, alumina of fly ash and part of calcium hydroxide, and (ii) CSH, by hydration of silica contained in fly ash and residual lime, was observed within both the reacting systems. For the FGD gypsum-based mixture, the conversion toward ettringite and CSH was highest at 70 °C and increased with curing time. Some discrepancies in the hydration behavior between the mixtures were ascribed to differences in mineralogical composition between natural and FGD gypsum.     

A methodology to determine gaseous emissions in a composting plant

Environmental impacts associated to different waste treatments are of interest in the decision-making process at local, regional and international level. However, all the environmental burdens of an organic waste biological treatment are not always considered. Real data on gaseous emissions released from full-scale composting plants are difficult to obtain. These emissions are related to the composting technology and waste characteristics and therefore, an exhaustive sampling campaign is necessary to obtain representative and reliable data of a single plant. This work proposes a methodology to systematically determine gaseous emissions of a composting plant and presents the results obtained in the application of this methodology to a plant treating source-separated organic fraction of municipal solid waste (OFMSW) for the determination of ammonia and total volatile organic compounds (VOC). Emission factors from the biological treatment process obtained for ammonia and VOC were 3.9 kg Mg OFMSW⁻¹ and 0.206 kg Mg OFMSW⁻¹ respectively. Emissions associated to energy use and production were also quantified (60.5 kg CO₂ Mg OFMSW⁻¹ and 0.66 kg VOC Mg OFMSW⁻¹). Other relevant parameters such as energy and water consumption and amount of rejected waste were also determined. A new functional unit is presented to relate emission factors to the biodegradation efficiency of the composting process and consists in the reduction of the Respiration Index of the treated material. Using this new functional unit, the atmospheric emissions released from a composting plant are directly related to the plant specific efficiency.