纳滤膜深度处理棉针织品印染废水

采用芳香聚酰胺膜(NF-1#)、复合膜(NF-2#)和聚酰胺复合膜(NF-3#)深度处理棉针织品印染废水，考察了膜分离性能及膜污染情况的影响因素。实验结果表明，在操作压力为0.5MPa、废水温度为25~35℃、废水pH为7的条件下，NF-1#膜处理效果最佳，COD去除率最高，为76.0%~85.0%;脱盐率也最高，达90.0%。膜过滤后浓水送污水厂处理，产水回用于车间生产。操作压力增高、废水温度升高和废水pH增大均导致滤饼层阻力(Rc)和膜过滤过程中的总阻力(Rt)增加，Rc是Rt的主要组成部分，同时也是导致膜透过通量下降的主要因素。     

Extracting humic acids from digested sludge by alkaline treatment and ultrafiltration

The concentration of hardly biodegradable humic substances in sludge would relatively increase after anaerobic digestion due to the degradation of other organic substances. Thus, extracting humic substances from digested sludge as a liquid organic fertilizer was tested using alkaline treatment and ultrafiltration, and the dewaterability of the residual sludge was also tested. The results showed that the contents of humic acids and fulvic acids in digested sludge were 16.4 mg/g total solids and 88.9 mg/g total solids, respectively, and most of the humic acids had a molecular weight higher than 50 kDa. Hence, the membrane with a molecular weight cut-off of 50 kDa was used for humic acids recovery from the centrifugation supernatant after alkaline sludge disintegration with an optimum NaOH dose of 0.1 mol/L. Under these conditions, the total concentration of humic acids and fulvic acids was 4239 mg/L in the retention solution, which can be further concentrated and processed for liquid fertilizer. The total recovery rate of sludge humic acids and fulvic acids was about 25 %. The dewatering performance of the residual sludge was better than that of the untreated sludge when the residual sludge was diluted to a water content of 95–98 % and then conditioned with polyacrylamide at a dose of 10–30 mg/L.     

Synthesis and Characterization of a Thin-Film Composite Nanofiltration Membrane Based on Polyamide-Cellulose Acetate: Application for Water Purification

Membrane separation has been widely used for various applications including microfiltration (MF), ultrafiltration (UF), and nanofiltration (NF) processes in the fields of biomedicine, food, and water purification. In this work, a facile synthesis of new polyamide thin-film composite nanofiltration membranes (NF-TFC) for water purification was described. The polyamide thin film was deposed over a synthetic cellulose acetate (CA) support by interfacial polymerization method. 1,3 cyclohexane bis (methylamine) (CHMA) and trimesoyl chloride (TMC) were used as monomers. The membranes were characterized using Scanning Electron Microscopy (SEM), Fourier Transform Infrared spectroscopy (FT-IR), water uptake, porosity, contact angle, water permeability and rejection towards specific salt and dye molecules. The effect of the variation of the CHMA concentration (0.2–2 wt.%) on the morphology, porosity, water permeation and rejection properties of the prepared membranes was studied. SEM results displayed the growth of the membrane thickness when the CHMA concentration increased from 0.2 to 2 wt.%. The strong adhesion between the cellulose acetate substrate and the polyamide layer explained by the formation of the polyamide film in the substrate surface and inside the pores. The water permeability varied from 36.02 to 17.09 L h^?1 m^?2 bar^?1. The salt rejection of Na₂SO₄ and NaCl increased from 9 to 68% and from 38.41% to 89.4%, respectively, when the CHMA concentration was changed from 0.2 to 2 wt.%. The prepared membranes were further applied successfully for the removal of malachite green and congo red. The results indicated that the maximum rejection reached 89% and 85% for malachite green and congo red, respectively.

     

Market potential of biomethane as alternative transportation fuel in South Korea

This study estimated domestically available energy amount of biomethane including landfill gas (LFG) as a transportation fuel by 2035. The amount of available energy that could be supplied was predicted through four stages of ‘theoretical-’, ‘geographical-’, ‘technical-’, and ‘market potential’ by considering geographical, technical, economic conditions, etc. Energy efficiency and added value of biomethane are largely influenced by the site conditions and the neighboring infrastructures. So, how much of the natural gas used in transportation could be substituted with biomethane was examined by setting limits to the amount of organic wastes generated within urban areas. As a result, the market potential of biomethane including landfill gas was approximately 331 × 10⁶ Nm³/year, corresponding to 25% of the natural gas supply for transportation, which could be replaced by biomethane. Assuming that 2% of natural gas for transportation is replaced by biomethane, it corresponds to 29 × 10⁶ Nm³/year (approximately 9% of market potential of biomethane). However, RFS annual mixing rate may be increased upon introduction and the growth rate of the natural gas supply for transport would be higher than that of market potential of biomethane calculated in this study.     

Some Investigations on the Nylon 6/Zn Composite Material Obtained by Simultaneous Anionic Polymerization-Molding Process

This study is concerned with the behavior of samples based on nylon 6/zinc (Ny6/Zn) composite material in high salinity water that contains NaCl (3.5 wt%) and in aqueous solution of HCl (0.5 N and 1 N). The samples were obtained from parts prepared by in situ anionic ring-opening polymerization of ?-caprolactam (CL) in the presence of zinc (Zn), as filler (15 wt%) using the rotational molding technique. This type of composite was evaluated by the testing of swelling degree, structural modifications, evolution of hydrogen and electrochemical behavior. The properties of Ny6/Zn composite material have ascertained through the combined use of more analysis methods: attenuated total reflectance Fourier transform infrared spectroscopy, wide-angle X-ray diffraction technique, scanning electron microscopy, swelling and electrochemical measurements. It was revealed that regarding swelling behavior the Ny6 matrix has an important role while Zn filler contributes especially to the (electro)chemical corrosion.     

海藻酸钠-聚乙烯醇-聚乙二醇复合膜的制备及其对Cu2+的吸附

采用聚乙烯醇（PVA）、聚乙二醇（PEG）对海藻酸钠（SA）进行改性，制备了一种新型高效SA-PVA-PEG复合膜。研究了该复合膜对Cu²⁺的吸附效果。用IR和SEM等手段对复合膜进行了表征。表征结果显示，复合膜内部存在孔状结构，有利于吸附Cu²⁺。实验结果表明：在初始Cu²⁺质量浓度50 mg/L、复合膜加入量1 g/L、废水pH=5、吸附温度30 ℃、吸附时间60 min的最佳条件下，吸附率最高可达90.1%，吸附量达25.3 mg/g；复合膜吸附Cu²⁺的动力学过程可用二级动力学方程和Elovice方程进行拟合，吸附过程符合Langmuir单层吸附理论。采用浓度为1 mol/L的HCl溶液对吸附后的复合膜进行解吸，当解吸时间为2 min时，解吸率可达80.0%。     

Development of Proteinous Bioplastics Using Bloodmeal

The aim of this work was to investigate the use of bloodmeal as a thermoplastic biopolymer. Processing required water and chemical additives to perform three main functions: breaking covalent cross-links using sodium sulfite (SS), sodium dodecyl sulfate and urea as processing aids, and evaporating some processing water to allow formation of new interactions to stabilize the final structure. Extrusion was only possible in the presence of SS and strongly influenced by water and urea content. It was found that once water had been removed, mechanical properties increased significantly, indicating the formation of new intermolecular forces. SDS was required for processing and consolidation, but, it may restrict formation of new intermolecular forces, if used in excessive quantities. Materials based on optimal additive levels had a tensile strength of 8 MPa, Young’s modulus of 320 MPa and toughness 1.6 MPa m^½.     

无机陶瓷膜MBR处理己内酰胺生产废水

采用无机陶瓷膜分离装置对己内酰胺生产废水处理工艺中的初沉池出水进行泥水分离.实验结果表明:无机陶瓷膜分离装置能有效去除废水中的悬浮物和COD,悬浮物去除率达90％以上,出水悬浮物质量浓度在1 mg/L以下；COD去除率为70％以上,出水COD在100 mg/L以下；采用质量分数为5％的NaOH溶液能对无机陶瓷膜分离装置...     

Fabrication and Characterization of Biodegradable Composite Films Made of Using Poly(caprolactone) Reinforced with Chitosan

Chitosan was dissolved in 2?% aqueous acetic acid solution and the films were prepared by solution casting. Values of tensile strength (TS), tensile modulus (TM), elongation at break (Eb?%) and water vapor permeability (WVP) of the chitosan films were found to be 30?MPa, 450?MPa, 8?% and 4.7?g?mm/m²?day?kPa, respectively. Poly(caprolactone) (PCL) films were prepared from its granules by compression molding and the values of TS, TM, Eb and WVP were 14?MPa, 220?MPa, 70?% and 1.54?g?mm/m²?day?kPa, respectively. PCL was reinforced with chitosan films, and composite films were prepared by compression molding. Amount of chitosan in the composite films varied from 10 to 50?% (w/w). It was found that with the incorporation of chitosan films in PCL, both the values of TS and TM of composite films increased significantly. The highest mechanical properties were found at 50?% (w/w) of chitosan content. The Oxygen transmission rate (OTR) of composite film was found to decrease significantly than PCL films. Thermal properties of the composite were also improved as compared to PCL. The water uptake test of the composite also showed promising results with a good stability of composite films. The interface of the composite was investigated by scanning electron microscopy and showed good interfacial adhesion between PCL and chitosan films.     

Processing and characterization of a new biodegradable composite made of a PHB/V matrix and regenerated cellulosic fibers

In this study, a biodegradable composite consisting of a degradable continuous cellulosic fiber and a degradable polymer matrix—poly(3-hydroxybutyrate)-co-poly(3-hydroxyvalerate (PHB/V with 19% HV)—was developed. The composite was processed by impregnating the cellulosic fibers on-line withPHB/V powder in a fluidization chamber. The impregnated roving was then filament wound on a plate and hot-pressed. The resulting unidirectional composite plates were mechanically tested and optically characterized by SEM. The fiber content was 9.9 ±0.9 vol% by volumetric determination. The fiber content predicted by the rule of mixture for unidirectional composites was 13.8 ±1.4 vol%. Optical characterization showed that the fiber distribution was homogeneous and a satisfactory wetting of the fibers by the matrix was achieved. Using a blower to remove excess matrix powder during processing increased the fiber content to 26.5 ±3.3 vol % (volumetric) or 30.0 ±0.4 vol% (rule of mixture). The tensile strength of the composite parallel to the fiber direction was 128 ±12 MPa (10 vol% fiber) up to 278 ±48 MPa (26.5 vol% fiber), compared to 20 MPa for the PHB/V matrix. The Young’s modulus was 5.8 ±0.5 GPa (10 vol% fiber) and reached 11.4 ±0.14 GPa (26.5 vol% fiber), versus 1 GPa for the matrix.     

Remediation with cyclodextrin: Recovery of the remedial agent by membrane filtration

Cyclodextrin‐enhanced flushing of contaminants from the subsurface is a promising innovative remediation technology. It will become more economically viable at more sites if methods can be developed to recover and reconcentrate the cyclodextrin solution after it has been flushed through an aquifer. The goal of this study was to determine if membrane technology is capable of meeting that need. Five membranes with different material properties were tested for this purpose in the laboratory. The results of these tests indicate that there are large differences both in the efficiency of these membranes to extract hydroxpropyl‐β‐cyclodextrin (HPCD) and their stability when exposed to trichloroethylene (TCE) at concentrations near aqueous solubility. Not only does the molecular weigh cutoff (MWCO) of a membrane determine if HPCD can be retained, but crucial selection criteria are the membrane's resistance and compatibility with TCE. Of the five membrane materials tested, only two (polymer composite membrane and polysulfone) met both these requirements. The polymer composite membrane (MPF‐44) showed reliable and stable HPCD recoveries (>95 percent) even when exposed to high TCE concentrations. The polysulfone membrane showed high HPCD recoveries, 88.5 ± 0.4 percent to 97 percent ±1 percent for ultrafiltration and nanofiltration membranes, respectively. However, membrane swelling and deterioration became a problem at high TCE concentrations (>1,000 mg/L). These problems diminished when the TCE concentration was less than 1 mg/L. Field tests demonstrated that batch mode treatment by ultrafiltration doubled the cyclodextrin concentration from 5 to 10 percent within three hours at a constant operating pressure of 13 psi. Under continuous single‐pass treatment conditions, cyclodextrin concentration also increased, although the rate of increase was much smaller than in batch mode. Overall, these tests showed that cyclodextrin recovery is possible under field conditions. © 2007 Wiley Periodicals, Inc.     

Electrodialysis for NaCl/EG solution using ion-exchange membranes

A new concept for the recycling of poly(vinyl chloride) (PVC) has been introduced, including the dehydrochlorination of PVC in ethylene glycol (EG) with NaOH as a reactant, the subsequent separation of NaCl from EG by electrodialysis, and the recovery of chlorine for the synthesis of new PVC. In this work, the separation of NaCl by electrodialysis was investigated. About 98 % of the salt were recovered from EG, with less than 10 % of the EG permeating the membranes after 5 h.     

催化臭氧氧化—好氧生化—膜分离组合工艺处理砷化镓生产废水的工程应用

为了解决砷化镓生产废水含有磷酸盐、氟化物、砷化物以及难沉降亚微米级悬浮物的处理难点,首先采用催化臭氧氧化—好氧生化深度预处理废水,再采用RO膜分离工艺进行处理。结果表明：催化臭氧氧化法使废水中亚微米级悬浮物脱稳,有利于悬浮物的混凝沉降,并优化了膜分离阶段的分离环境,可延长膜使用寿命,降低运行成本;经过膜分离后,出水砷质量浓度为0.01 mg/L,氟质量浓度为1.0 mg/L,COD、TP、TN和ρ（NH₃-N）为10,0.01,0.50,0.50 mg/L,均达到《地表水环境质量标准》（GB3838—2002）Ⅲ类水质标准。     

聚结晶紫膜修饰电极的制备及对水中对苯二酚和邻苯二酚的测定

通过电化学的方法将结晶紫聚合在玻碳电极表面制备聚结晶紫(PCV)膜修饰电极，并研究了对苯二酚和邻苯二酚在PCV膜修饰电极上的电化学行为。PCV膜修饰电极对对苯二酚和邻苯二酚的氧化有良好的电催化作用。在最佳的实验条件下，氧化峰电流在对苯二酚和邻苯二酚的浓度为4.0×10-6~2.8×10-4mol/L之间呈良好线性关系，对苯二酚和邻苯二酚的线性相关系数分别为0.9991和0.9823，检出限分别为6.2×10-7mol/L和9.0×10-7mol/L。PCV膜修饰电极具有良好的灵敏度、重现性和稳定性，可以应用于实际水样中两种物质的同时测定。     

The Removal of Acid Violet 90 from Aqueous Solutions Using PANI and PANI/Clinoptilolite Composites: Isotherm and Kinetics

Polyaniline (PANI) and polyaniline/Gördes-clinoptilolite (PANI/GC) composite materials were synthesized by the chemical oxidative polymerization technique and used in the adsorption of Acid Violet 90 metal-complex dye (AV 90). The samples were characterized by X-ray diffractions, nitrogen adsorption–desorption isotherms, scanning electron microscopes and Fourier transform infrared. The effect of initial pH (2–8), sorbent dosage (0.5–4.0 g/L) and initial dye concentrations (50–400 mg/L) on adsorption onto PANI and PANI/GC were examined in a batch system. Langmuir, Freundlich and Temkin isotherm models were used to investigate the adsorption mechanism of AV 90 on PANI and PANI/GC. Langmuir isotherm model for PANI/GC and Freundlich isotherm model for PANI were fitted well with the experimental data. The highest dye uptake capacities were obtained with Langmuir isotherm model as 153.85 mg/g and 72.46 mg/g for PANI and PANI/GC, respectively. In order to determine the adsorption kinetics, pseudo first-order and second-order kinetic models were studied. As a result, the adsorption of AV 90 dye on PANI and PANI/GC was better identified with Pseudo second-order kinetic model than the first one.     

Properties of Composite Panels Made from Tetra-Pak and Polyethylene Waste Material

The objective of this study was to evaluate some of the properties of experimental composite panels manufactured from waste packaging materials without using any additional binders. Particles from three types of materials, namely Tetra-Pak, food packaging films (FPEF) as recycled stretch wraps, and candy polyethylene wrappers (CPEW) were used at different ratios in the panels at a target density of 900 kg/m³. Modulus of rupture (MOR), screw holding strength and dimensional stability in the form of thickness swelling and water absorption of the panels were determined according to European (EN) standards. Based on the findings in this work it was determined that the ratio of different raw materials significantly influenced overall properties of the samples. The highest MOR value of 15.5 MPa was determined for the samples having 40 % Tetra-Pak and 60 % CPEW particles. Modulus of rupture values of the panels decreased with decreasing content of CPEW in the samples. The increased content of Tetra-Pak particles in the samples also resulted in reduction of their strength characteristics and dimensional stability. Properties of the samples considered in this work satisfied minimum requirements of typical particleboard stated in EN standards. It appears that such waste material would have potential to be used as raw material for value-added composite production using no adhesive in the panels and, therefore, such panels would possibly create significant ecological impact as green product.     

Preparation of Natural Rubber/Condensed Tannin Semi-interpenetrating Polymer Network Composites by Hematin-Catalyzed Cross-Linking

In this study, the preparation of semi-interpenetrating polymer network (semi-IPN) composites composed of natural rubber and condensed tannin was performed by means of the enzyme-mimetic cross-linking of condensed tannin catalyzed by hematin. Prior to the preparation of the composites, the hematin-catalyzed cross-linking behavior of condensed tannin was evaluated by the TGA measurement. The TGA results indicated that condensed tannin was sufficiently cross-linked by the hematin-catalyzed reaction in the presence of appropriate amounts of 30% (w/v) H₂O₂ aq. to give the relatively thermostable materials. For the preparation of the composites, a solution of condensed tannin and hematin, and subsequently 30% (w/v) H₂O₂ aq. were added to natural rubber latex and the mixture was stirred at room temperature for 10 min to perform the cross-linking of condensed tannin, followed by drying of the reaction mixture at 50 °C for 5 h, which was subsequently put into a heat device and hot-pressed at 100 °C and 20 MPa for 20 min to give the semi-IPN composite. The tensile stress?Cstrain measurement of the composites was conducted to evaluate the mechanical properties, which were changeable depending on the weight ratios of natural rubber to condensed tannin and the amounts of 30% (w/v) H₂O₂ aq. Moreover, the miscibility of the cross-linked tannin with natural rubber in the composite was evaluated by the SEM measurement.     

Composition and management of rechargeable electric torch wastes in Ibadan,Nigeria

The consumption, disposal, material and chemical compositions of rechargeable electric torch wastes (RETWs) were investigated in Ibadan, Nigeria. Twenty-five RETWs of ten models were collected and disassembled. Their battery electrodes (BEs) and printed circuit boards (PCBs) were acid digested and leached using United States Environmental Protection Agency (USEPA) method 3050B and USEPA Method 1311, respectively. The digests and extracts were analysed for total and extractable Pb, Cd, Cr and Ni using atomic absorption spectrophotometer. The US Test method (CPSC-CH-E 1002-08) was used for digestion of the plastic components. Two hundred questionnaires were distributed to users in Ibadan to determine their usage of RETs and their management when spent. The results indicated that BEs contributed the highest percentage (44 %) component, followed by plastic (38 %). Other components include metal, PCBs, glass and wire. Of the respondents, 61.9 % dispose their spent torches in dumpsites. The mean ± SD concentrations of Pb, Cd, Cr and Ni in the BEs were 500 ± 109 g/kg, 3.94 ± 6.84 mg/kg, 0.33 ± 0.88 mg/kg, 1.68 ± 0.74 mg/kg respectively; in the PCBs, they were 684 ± 42 g/kg, 13.7 ± 17.8 mg/kg, 13.5 ± 10.2 mg/kg and 193 ± 437 mg/kg; and in the plastics, they were 14.1 g/kg, 5.33 mg/kg, 17 mg/kg, and 4.67 mg/kg respectively. The extractable Pb in BE (2670 mg/L) and PCBs (235 mg/L) exceeded the Toxicity Characteristics Leaching Procedure (TCLP) limit of 5 mg/L. RETWs present potential environmental problems in the absence of effective recycling.     

High Toughness and Fast Crystallization Poly(Lactic Acid)/Polyamide 11/SiO<Subscript>2</Subscript> Composites

A poly(lactic acid) (PLA)/polyamide 11 (PA11)/SiO₂ composite was mixed from PLA, PA11, and nanosilica particles through twin-screw extrusion. The PLA/PA11/SiO₂ composite was evaluated with tensile and Izod impact tests, light transmission and haze measurement, and isothermal and nonisothermal crystallization behavior determinations. The PLA/PA11/SiO₂ (97.0/3.0) composite had approximately 10.8% less ultimate tensile strength than neat PLA, but it had greater ductility and approximately ninefold greater elongation at break. A dimple morphology was observed on the fractural surface of the PLA/PA11/SiO₂ composite, indicating that the incorporation of PA11 and nanosilica particles increased the ductility of the PLA matrix. PLA with less than 3 wt% of PA11 and 0.5 phr of nanosilica particles had an Izod impact strength of 8.72 kJ/m². PA11 and nanosilica particles effectively toughened this PLA polymer; they accelerated both isothermal and nonisothermal crystallization rates and increased the crystallinities of the resulting composites under isothermal and nonisothermal crystallization processes.     

Synthesis and Properties of Polyesters from Waste Grapeseed Oil: Comparison with Soybean and Rapeseed Oils

The aim of this study was to investigate the application of grapeseed oil, a waste product from the wine industry, as a renewable feedstock to make polyesters and to compare the properties of these materials with those derived from soybean and rapeseed oils. All three oils were epoxidized to give renewable epoxy monomers containing between 3.8 and 4.7 epoxides per molecule. Polymerisation was achieved with cyclic anhydrides catalysed by 4-methyl imidazole at 170 and 210 °C. Polymers produced from methyl tetrahydrophthalic anhydride (Aradur917^®) had greater tensile strength and Young’s Modulus (tensile strength = 12.8 MPa, Young’s Modulus = 1005 MPa for grapeseed) than methyl nadic anhydride (MNA) derived materials (5.6 and 468 MPa for grapeseed) due to increased volume of MNA decreasing crosslink density. Soybean and grapeseed oils produced materials with higher tensile strength (5.6–29.3 MPa) than rapeseed derived polyesters (2.5–3.9 MPa) due to a higher epoxide functionality increasing crosslinking. T _g’s of the polyesters ranged from ?36 to 62 °C and mirrored the trend in epoxide functionality with grapeseed producing higher T _g polymers (?17 to 17 °C) than soybean (?25 to 6 °C) and rapeseed (?36 to ?27 °C). Grapeseed oil showed similar properties to soybean oil in terms of T _g, thermal degradation and Young’s Modulus but produced polymers of lower tensile strength. Therefore grapeseed oil would only be a viable substitute for soybean for low stress applications or where thermal properties are more important.