凹凸棒土/苯胺-邻氨基酚复合吸附剂的制备及其对Cr(Ⅵ)的吸附性能

采用原位聚合法制备了凹凸棒土/苯胺-邻氨基酚（ATP/PANOAP）复合吸附剂,对其进行了SEM和FTIR表征,并通过吸附实验考察了ATP/PANOAP对水中Cr（Ⅵ）的吸附性能。实验结果表明,ATP/PANOAP对水中Cr（Ⅵ）具有良好的去除效果,在Cr（Ⅵ）初始质量浓度为50 mg/L、溶液pH为6、吸附剂加入量为0.375 g/L、温度为298 K的条件下,Cr（Ⅵ）去除率达93.39%。ATP/PANOAP对Cr（Ⅵ）的吸附动力学过程符合准二级动力学模型,吸附热力学过程符合Langmuir单层吸附模型,该吸附过程以化学吸附为主,且为自发进行的吸热反应。     

前驱体溶液pH对核壳型Cr/CeO2催化剂低温选择性催化氧化脱硝性能的影响

采用一步水热法合成了具有核壳结构的铬铈复合氧化物（Cr/CeO₂）,并将其用于选择性催化氧化（SCO）烟气脱硝,考察了前驱体溶液pH对催化剂低温催化活性的影响。实验结果表明,当前驱体溶液pH为2时制得的催化剂（CrCe2）具有较高的低温SCO活性,其在200 ℃下的NO转化率高达59%。XRD,SEM,BET,UV-Vis,TPD等表征结果显示：核壳结构的生成促进了Cr物种的高分散性,同时Cr的掺杂增大了催化剂的比表面积,从而提高了活性位点的总量;在该系列催化剂中,CrCe2催化剂具有最高的表面六价铬和化学吸附氧的占比,因此呈现出最高的低温SCO活性。     

炭化核桃壳对废水中Cr（Ⅵ）的吸附

制备了炭化核桃壳,采用SEM,EDX,FTIR等方法对炭化核桃壳进行了表征,研究了炭化核桃壳对废水中Cr（Ⅵ）的吸附效果。表征结果显示,炭化后的核桃壳为片状结构,且形成了大量的微孔,微孔数量的增加使得核桃壳的比表面积明显增大。实验结果表明,炭化核桃壳吸附处理含Cr（Ⅵ）废水的最佳工艺条件为：初始废水pH 2.0、炭化核桃壳加入量16 g/L、吸附温度25 ℃、转速150 r/min、吸附时间180 min,在此最佳工艺条件下吸附处理Cr（Ⅵ）质量浓度为20 mg/L废水,Cr（Ⅵ）去除率高达98.7%,最大吸附量为8.731 mg/g。Langmuir吸附等温模型可更好地描述炭化核桃壳对Cr（Ⅵ）的吸附过程,吸附属于单分子层吸附。拟二级动力学方程能更好地描述炭化核桃壳对Cr（Ⅵ）的吸附行为,此吸附过程以化学吸附为主控步骤。     

炭化核桃壳对废水中Cr(Ⅵ)的吸附

制备了炭化核桃壳,采用SEM,EDX,FTIR等方法对炭化核桃壳进行了表征,研究了炭化核桃壳对废水中Cr(Ⅵ)的吸附效果。表征结果显示,炭化后的核桃壳为片状结构,且形成了大量的微孔,微孔数量的增加使得核桃壳的比表面积明显增大。实验结果表明,炭化核桃壳吸附处理含Cr(Ⅵ)废水的最佳工艺条件为:初始废水pH 2.0、炭化核桃壳加入量16 g/L、吸附温度25℃、转速150 r/min、吸附时间180 min,在此最佳工艺条件下吸附处理Cr(Ⅵ)质量浓度为20 mg/L废水,Cr(Ⅵ)去除率高达98.7%,最大吸附量为8.731 mg/g。Langmuir吸附等温模型可更好地描述炭化核桃壳对Cr(Ⅵ)的吸附过程,吸附属于单分子层吸附。拟二级动力学方程能更好地描述炭化核桃壳对Cr(Ⅵ)的吸附行为,此吸附过程以化学吸附为主控步骤。     

硫酸盐还原菌原位修复六价铬污染土壤

以FeSO₄化学还原法为对照,开展硫酸盐还原菌原位修复铬污染土壤的田间试验研究。试验结果表明:微生物法处理后,土壤中Cr(Ⅵ)含量从6.48 mg/kg降至0.95 mg/kg,下降率为85.33%,修复后的土地质量符合国家一类建设用地的标准;土壤浸出液中Cr(Ⅵ)质量浓度从0.162 mg/L降至0.004 mg/L,下降率为97.53%;土壤中硫酸根浓度略有降低,硫酸盐还原菌的丰度显著增加。微生物原位修复铬污染土壤的效果好于化学还原法。     

薏米壳生物炭的制备及其对Cr（Ⅵ）的吸附性能

采用限氧控温热分解法在不同温度下制备了薏米壳生物炭。研究了薏米壳生物炭对低浓度Cr（Ⅵ）的吸附性能及吸附机理。随碳化温度升高,薏米壳管状通道微孔结构逐渐显现,薏米壳生物炭表面芳香化程度增强。薏米壳生物炭对Cr（Ⅵ）的吸附行为采用Langmuir等温吸附模型吻合度更高,吸附属于单分子层化学吸附,吸附过程是自发的、熵增吸热反应,吸附过程遵循准二级吸附动力学模型,膜扩散和颗粒内扩散共同控制吸附过程。     

薏米壳生物炭的制备及其对Cr(Ⅵ)的吸附性能

采用限氧控温热分解法在不同温度下制备了薏米壳生物炭。研究了薏米壳生物炭对低浓度Cr(Ⅵ)的吸附性能及吸附机理。随碳化温度升高,薏米壳管状通道微孔结构逐渐显现,薏米壳生物炭表面芳香化程度增强。薏米壳生物炭对Cr(Ⅵ)的吸附行为采用Langmuir等温吸附模型吻合度更高,吸附属于单分子层化学吸附,吸附过程是自发的、熵增吸热反应,吸附过程遵循准二级吸附动力学模型,膜扩散和颗粒内扩散共同控制吸附过程。     

CFB锅炉灰渣的应用研究

总结了CFB锅炉灰渣与常规灰渣物理、化学特性的差异，分析了这些特性在应用中的优劣性，并介绍了CFB锅炉灰渣的应用现状．     

气化炉渣的重金属浸出特性及化学形态分析

分别采用硫酸硝酸法、水平振荡法和醋酸缓冲溶液法制取气化炉渣的浸出液，考察了不同提取方式对浸出液中重金属质量浓度的影响。采用改进BCR连续提取法对气化炉渣中的重金属Cr，Zn，Cu，Pb，Ni，As，Cd的化学形态进行了分析。实验结果表明：煤气化工艺中的气化炉渣属第Ⅰ类一般工业固体废物;在3种提取方式中，醋酸缓冲溶液法的重金属浸出种类最多，且浸出量最大;Cd和Cr对环境具有较高的潜在危害性，Cu次之，Zn，Pb，Ni，As主要以残渣态形式存在，对环境的直接危害性较低。     

燃煤电厂汞排放监测和控制研究现状

介绍了燃煤电厂汞控制研究现状,分析了燃煤中汞的含量和赋存状态、燃烧中汞的化学行为特性,探讨了汞的监测和控制技术,为我国燃烧电厂汞排放控制提供参考.     

Determination of the Thermal Efficiency of Pre-boilover Burning of a Slick of Oil on Water

The burning rate of a slick of oil on a water bed is calculated by a simple expression derived from a one-dimensional heat conduction equation. Heat feedback from the flame to the surface is assumed to be a constant fraction of the total energy released by the combustion reaction. The constant fraction (χ) is named the burning efficiency and represents an important tool in assessing the potential of in situ burning as a counter-measure to an oil-spill. The total heat release, as a function of the pool diameter, is obtained from an existing correlation. It is assumed that radiative heat is absorbed close to the fuel surface, that conduction is the dominant mode of heat transfer in the liquid phase and that the fuel boiling temperature remains constant. By matching the characteristic thermal penetration length scale for the fuel/water system and an equivalent single layer system, a combined thermal diffusivity can be calculated and used to obtain an analytical solution for the burning rate. Theoretical expressions were correlated with crude oil and heating oil, for a number of pool diameters and initial fuel layer thickness. Experiments were also conducted with emulsified and weathered crude oil. The simple analytical expression describes well the effects of pool diameter and initial fuel layer thickness permitting a better observation of the effects of weathering, emulsification and net heat feedback to the fuel surface. Experiments showed that only a small fraction of the heat released by the flame is retained by the fuel layer and water bed (of the order of 1%). The effect of weathering on the burning rate decreases with the weathering period and that emulsification results in a linear decrease of the burning rate with water content.     

Selection of adsorbents for treatment of leachate: batch studies of simultaneous adsorption of heavy metals

The simultaneous adsorption of copper (Cu), cadmium (Cd), nickel (Ni), and lead (Pb) ions from spiked deionized water and spiked leachate onto natural materials (peat A and B), by-product or waste materials (carbon-containing ash, paper pellets, pine bark, and semi-coke), and synthetic materials (based on urea-formaldehyde resins, called blue and red adsorbents) or mixtures thereof was investigated. The adsorbents that gave the highest metal removal efficiencies were peat A, a mixture of peat B and carbon-containing ash, and a mixture of peat A and blue. At an initial concentration of 5 mg/l for each metal, the removal of each species of metal ion from spiked water and spiked leachate solutions was very good (>90%) and good (>75%), respectively. When the initial concentration of each metal in the solutions was twenty times higher (100 mg/l), there was a noticeable decrease in the removal efficiency of Cu²⁺, Cd²⁺, and Ni²⁺, but not of Pb²⁺. Langmuir monolayer adsorption capacities, q_m, on peat A were found to be 0.57, 0.37, and 0.36 mmol/g for Pb²⁺, Cd²⁺, and Ni²⁺, respectively. The order of metal adsorption capacity on peat A was the same in the case of competitive multimetal adsorption conditions as it was for single-element adsorption, namely Pb²⁺ > Cd²⁺ ≥ Ni²⁺. The results show that peat alone (an inexpensive adsorbent) is a good adsorbent for heavy metal ions.     

富拉尔基发电总厂200MW机组除尘器改造

对富拉尔基发电总厂5号炉的设计条件进行了分析，针对燃用低硫煤，飞灰比电阻高，场地较小，除尘效率要求高的情况，在电除尘器的设计上采取有效措施，达到了排放要求。     

Calculation of carbon balances for evaluation of the biodegradability of polymers

Establishing carbon balances has been proven to be an applicable and powerful tool in testing biodegradability of polymers. In controlled degradation tests at a 4-L scale with the model polymer poly(-hydroxybutyrate) (PHB), it was shown that the degree of degradation could not be determined with satisfactory accuracy from CO₂ release alone. Instead, the course of degradation was characterized by means of establishing carbon balances for the degradation of PHB withAcidovorax facilis and a mixed culture derived from compost. Different analytical methods for determining the different carbon fractions were adapted to the particular test conditions and compared. Quantitative determination of biomass and residual polymer were the main problems in establishing carbon balances. Amounts of biomass derived from protein measurements depend strongly on assumptions of the protein content of the biomass. Selective oxidation of biomass with hypochlorite was used as alternative, but here problems arose from insoluble metabolic products. Determination of soluble components with the method of chemical oxygen demand (COD) also includes empirical assumptions but seems acceptable if the dissolved carbon fraction is in the range of some 10% total carbon. Results confirm both analytical assays and theoretical approaches, in ending up at values very close to 100%, within an acceptable standard deviation range under test conditions comparable to standard test practice.Paper presented at the Bio/Environmentally Degradable Polymer Society—Third National Meeting, June 6–8, 1994, Boston, Massachusetts.     

袋式除尘器气流分布数值计算研究

采用结构化/非结构化混合网格技术、多孔介质模型及k-ε两方程湍流模型,对某袋式除尘器及进出口管道内的气体流场进行了数值计算.计算结果表明,合理布置导流板后,袋式除尘器两箱体流量偏差为1.8％;除尘器下游滤袋单元处理气量偏大,中游滤袋单元处理气量较小,最大流量与最小流量偏差为22.3％；靠近除尘器进口处灰斗内存在气流回流特性,易造成粉尘的二次附着现象.     

Kinetics of Hydrolytic Degradation of PLA

The chemical recycling of poly(lactic acid) (PLA) to its monomer is crucial to reduce both the consumption of renewable resources for the monomer synthesis and the environmental impact related to its production and disposal. In particular, the production of lactic acid from PLA wastes, rather than from virgin raw materials, it is also possible to achieve considerable primary energy savings. The focus of this work is to analyse deeply the PLA hydrolytic decomposition by means of a kinetic model based on two reactions mechanism. To this end, new experimental data have been gathered in order to investigate a wider temperature range (from 140 to 180 °C) and to extend the water/PLA ratio up to 50 % of PLA by weight. The reported results clearly highlight that more than 95 % of PLA is hydrolyzed to water-soluble lactic acid within 120 min, when it is hydrolyzed within 160–180 °C. Furthermore, the kinetic constant is highly influenced by reaction temperature. The proposed “two reactions” kinetic mechanism complies satisfactorily with the experimental data under analysis.     

Review of the kinetics of alkaline degradation of cellulose in view of its relevance for safety assessment of radioactive waste repositories

The degradation of cellulose (a substantial component of low- and intermediate-level radioactive waste) under alkaline conditions occurs via two main processes: a peeling-off reaction and a basecatalyzed cleavage of glycosidic bonds (hydrolysis). Both processes show pseudo-first-order kinetics. At ambient temperature, the peeling-off process is the dominant degradation mechanism, resulting in the formation of mainly isosaccharinic acid. The degradation depends strongly on the degree of polymerization (DP) and on the number of reducing end groups present in cellulose. Beyond pH 12.5, the OH^- concentration has only a minor effect on the degradation rate. It was estimated that under repository conditions (alkaline environment, pH 13.3-12.5) about 10% of the cellulosic materials (average DP = 1000-2000) will degrade in the first stage (up to 10⁵ years) by the peeling-off reaction and will cause an ingrowth of isosaccharinic acid in the interstitial cement pore water. In the second stage (10⁵-10⁶ years), alkaline hydrolysis will control the further degradation of the cellulose. The potential role of microorganisms in the degradation of cellulose under alkaline conditions could not be evaluated. Proper assessment of the effect of cellulose degradation on the mobilization of radionuclides basically requires knowing the concentration of isosaccharinic acid in the pore water. This concentration, however, depends on several factors such as the stability of ISA under alkaline conditions, sorption of ISA on cement, formation of sparingly soluble ISA-salts, etc. A discussion of all the relevant processes involved, however, is far beyond the scope of the presented overview.     

Study of Aging Characteristics of Ternary Blends of Polyethylenes—II

Six film samples of low-density polypropylene (LDPE)/linear LDPE (LLDPE)/high-density polypropylene (HDPE) with varying ratios of LDPE (20–45 ... wt%) and LLDPE (25–50 wt%) having a fixed amount of HDPE at 30 wt% were prepared by blown film extrusion technique. The samples were aged at four different temperatures, 55°, 70°, 85°, and 100°C, for four different time periods in the interval of between 150 hours and up to 600 hours. The change in the structure of various constituents and the formation of various oxygenated (peroxy and hydroperoxy) and unsaturated groups during thermo-oxidative degradation was discussed by infrared spectroscopy. The visiosity-average molecular weight was found to have decreased slowly in the initial aging hours and temperatures, whereas it decreased by 10% with its previous value tensile strength that is, 100°C when aged for 600 hours. The tensile strength of the sample first increased by 67% at 55°C and 89% at 70°C up to 450 hours, whereas the values increased by 52.5% at 85°C and 33.9% at 100°C when aged for 150 hours and then decreased. The percentage elongation at break increased by 2.7% at 55°C and 10.7% at 70°C for 150 and 300 hours of aging, respectively, whereas the percentage decreased when aged at 85°C and 100°C for up to 600 hours of aging. The values of gel content (percent) increased and initial degradation temperature decreased with aging time and temperature.     

Effect of Degree of Substitution of Octenyl Succinate Starch on Enzymatic Degradation

Octenyl succinate starch of degree of substitution (ds) 0.03, 0.07, and 0.11 was synthesized in an aqueous medium. These compounds were then tested for the susceptibility to enzymatic degradation. The multiple-enzyme regime of -amylase, amyloglucosidase, and pullulanase was chosen for the evaluation. This combination of enzymes had been proven to degrade 99.5% of unmodified starch to glucose and hence was chosen for this study. It was found that even small amounts of subsituent caused a considerable decrease in the extent of degradation. The net extent of degradation decreased with increasing ds. Surprisingly, the amount of glucose from all three substituted substrates was quite similar, suggesting the effect small amounts of subtituent had on the enzymatic activity.     

Effects of temperature on the release of nutrient elements of solid organic materials under conditions of oversaturation

The effects of temperature on the release of chemical components of six solid organic materials under conditions of oversaturation were investigated in this paper. The six materials were peat moss (PM), weathered coals (WC), charred rice husks (CRH), sawdust (Sd), turfgrass clippings (TC), and chicken manure (CM). Significant differences were observed in the available nitrogen and phosphorus content of the aqueous extracts of organic materials at different temperatures. The available nitrogen content in aqueous extracts of PM and WC at 25 °C was higher than that registered at 15 °C and 35 °C. Available nitrogen content in the aqueous extracts of CRH, Sd, TC, and WC at 35 °C was higher than at 15 °C and 25 °C. The available phosphorus content in the aqueous extracts of organic materials at 35 °C was higher than that available at 15 °C and 25 °C, with the exception of Sd. In addition, the release of available phosphorus in the aqueous solution of organic materials at different temperatures varied constantly for 108 h. The release of potassium (K⁺) and sodium (Na⁺) ions in the aqueous extracts of organic materials was basically steady over time, with the exception of CM. High temperature (35 °C) may significantly hasten the release of K⁺ from organic substrates (except for WC) with low temperatures significantly inhibiting release of K⁺ in Sd and CRH. High temperatures (35 °C) might significantly facilitate the release of Na⁺ in CM and TC. However, no significant differences were manifested in the release of Na⁺ from organic substrates at different temperatures, with the exception of CM and TC. Moreover, no significant differences were observed in the release of calcium, magnesium and iron ions with time, nor were there any significant differences in the contents of iron ions in the aqueous extracts of organic materials at different temperatures. The results indicate that multiple mediums should be pretreated in water for a week before being used for planting. They should be used when all mineral elements of organic materials are steady and ignoring the effect of organic mediums.