Thermal and Rheological Properties of Poly(lactic acid)/Low-Density Polyethylene Blends and Their Supercritical CO<Subscript>2</Subscript> Foaming Behavior

Low-density polyethylene (LDPE) was employed to improve the thermal and rheological properties as well as the supercritical CO₂ foaming behavior of poly(lactic acid) (PLA) through melt mixing and batch foaming method, due to its long branched chain structure, moderate crystallization capacity and good foamability. The differential scanning calorimetry and polarized optical microscope results showed that the introduction of LDPE had a slight effect for promoting the crystallization of PLA. An important synergistic effect on the rheological properties of PLA/LDPE blends was found through rotational rheometer. With the content of LDPE, the size of spherical LDPE dispersion phase became bigger gradually, which was observed by scanning electron microscope (SEM). A very interesting cellular morphology evolution from flower-like cellular structure to complex cellular structure and then to mono-porous cell structure was found in the SEM images of the PLA/LDPE blending foams with the foaming temperature at 95 °C. The effect of blending ratio and foaming temperature on the cellular morphology and foaming parameters was investigated.     

Effect of Oxidized Starch on Morphology,Rheological and Tensile Properties of Low-Density Polyethylene/Linear Low-Density Polyethylene/Thermoplastic Oxidized Starch Blends

In this work, morphology, rheological and tensile properties of low-density polyethylene/linear low-density polyethylene/thermoplastic oxidized starch (LDPE/LLDPE/TPOS) blends are studied. The blends of LDPE/LLDPE (70/30, w/w) containing 0–20 wt% TPOS in the presence of 3 wt% of PE-grafted maleic anhydride (PE-g-MA) as a compatibilizer are prepared by a twin screw extruder and then converted to appropriate thin films using an extrusion film blowing machine. Scanning electron microscopic images show that there is a relative good dispersion of oxidized starch particles in PE matrices. However, as TPOS content in the blends increases, the starch particle size increases too. The rheological analyses indicate that TPOS can decrease the elasticity and viscosity of the blends. The LDPE/LLDPE/TPOS blends show power-law behavior and as the TPOS content increases the power-law exponent (n) and consistency index (K) decrease. The ultimate tensile strength and elongation at break of the final blend films reduce, when TPOS content increases from 5 to 20 wt%. However, the required mechanical properties for packaging applications are achieved when 10 wt% oxidized starch is added, according to ASTM D4635.     

Conversion of Mixed Low-Density Polyethylene Wastes into Liquid Fuel by Novel CaO/SiO<Subscript>2</Subscript> Catalyst

Plastic wastes disposal can be done by various methods such as landfill, incineration, mechanical and chemical recycling but these are restricted due to some environmental, economic and political problems. Conversion of these plastic wastes into valuable products by degradation is the best option. In the present work waste low density polyethylene was degraded by catalytic process using CaO/SiO₂ as mixed catalyst. The conditions for catalytic degradation were optimized for the production of maximum liquid fuel. It was found that the yield of liquid product was up to 69.10 wt% at optimum condition of temperature (350 °C), time (90 min) and catalyst feed ratio (1:0.4). Liquid fuels obtained from the catalytic degradation were further separated into various fractions by fractional distillation. Composition of liquid fuels was analyzed by FTIR spectroscopy, which showed that the liquid fuels mostly consist of paraffinic and naphthenic hydrocarbons. Different fuel properties such as density, specific gravity, American petroleum institute gravity (API gravity), viscosity, kinematic viscosity, refractive index, refractive intercept and flash point of both the parents and various fractional fuels were determined. All the properties of the obtained fuels are in close agreement with the fuel properties of gasoline, kerosene and diesel. It was found that our catalyst is very much efficient in terms of time, degradation temperature and amount of catalyst.     

Effect of Nano-SiO<Subscript>2</Subscript> and Bark Flour Content on the Physical and Mechanical Properties of Wood–Plastic Composites

The aim of this study is to evaluate the impact of nano-SiO₂ and bark flour (BF) on the natural fiber–plastic composites engineering properties made from high density polyethylene (HDPE) and beech wood flour (WF). For this purpose, WF and BF in 60 mesh size and weight ratio of (50, 0 %), (30, 20 %), (10, 40 %) and (0, 50 %) respectively were mixed with HDPE. In order to increase the interfacial adhesion between the filler and the matrix, the maleic anhydride grafted polyethylene was constantly used at 3 wt% for all formulations as a coupling agent. The nano-SiO₂ particles with weight ratio of 0, 1, 2, and 4 % were also utilized to enhance the composites properties. The materials were mixed in an internal mixer (HAAKE) and then the bark and/or wood–plastic composite samples were made utilizing an injection molding machine. The physical tests including water absorption and thickness swelling, and mechanical tests including bending characteristics and un-notched impact strength were carried out on the samples based on ASTM standard. The results indicated that as the BF content increased in the composite, mechanical and physical properties were reduced, but the given properties were increased with the addition of nano-SiO₂. The addition of nano-SiO₂ had a negative impact on the physical properties, but when it was up to 2 %, it increased the impact strength.     

Influence of Filler Particle Size on Physical Properties and Biodegradation of Biocomposites Based on Low-Density Polyethylene and Lignocellulosic Fillers

This study examined biocomposites based on low-density polyethylene (LDPE) and lignocellulosic fillers [wood flour (WF) and oil flax straw (FS)] selecting four size fractions of each lignocellulosic material as fillers for the composites. The primary aim was to evaluate the influence of fraction size on the composites’ basic properties; to accomplish this, the composites’ mechanical properties, thermal oxidation, thermophysical characteristics, and water absorption capacity were examined. Then microphotographs of the samples were created and length-to-diameter (L/D) ratio of the fillers was calculated, finding that the L/D ratio increased with increasing particle size. The particle size influenced the oxidative degradation and water absorption processes in composites with oil flax but not in those with WF. Biodegradation tests performed on the recovered soil found that the loss of mass in composites based on LDPE and FS was higher than in the same composites with WF. Moreover, at the initial stage of composting, the biodegradation rate correlated with the size of filler particles (i.e., the larger the particles, the higher the degradation rate of the biocomposite).     

Degradation of starch-plastic composites in a municipal solid waste landfill

The rate and extent of deterioration of starch-plastic composites were determined over a 2-year period for samples buried in a municipal solid waste landfill. The deterioration of the starch-plastic composites following exposure was determined by measuring changes in tensile properties, weight loss, and starch content of samples retrieved from the landfill. Elongation decreases of 92 and 44% were measured for starch-plastic composite LDPE and LLDPE films, respectively, while elongation decreases of 54 and 21% were measured for their corresponding control films following 2 years of burial. Starch loss of 25% for LLDPE and 33% for LDPE starch-plastic composite films was measured following 2 years of landfill burial. Starch-plastic composites did not fragment or lose mass during the 2-year landfill burial. The limited degradation observed for the starch-plastic composites was attributed to the ineffectiveness of the prooxidant additive to catalyze the thermal oxidation of the polyethylene or polypropylene component of the starch-plastic composite under the environmental conditions present within the landfill.     

Tensile and Combustion Properties of PP/IFR/POE/nano-CaCO<Subscript>3</Subscript> Composites

The tensile and combustion properties of polypropylene/polyolyaltha olefin composites filled with intumescent flame retardant (IFR) and nanometer calcium carbonate (nano-CaCO₃) were measured. It was found that the values of the Young’s modulus of the composites increased almost linearly, while the values of the tensile yield strength and tensile fracture strength of the composites decreased with increasing the IFR weight fraction; the values of the elongation at break of the composites decreased quickly when the IFR weight fraction was lower than 10 wt%, and then varied slightly when the IFR weight fraction was higher than 10 wt%. Moreover, the morphology of the specimens after combustion was observed and the frame retardant mechanisms of the composites were discussed.     

Bio-based Polyethylene–Lignin Composites Containing a Pro-oxidant/Pro-degradant Additive: Preparation and Characterization

Formulations of low cost bio-based oxo-biodegradable polyethylene (PE)/Lignin hybrid polymeric composites were prepared by using ethylene/vinyl acetate (EVA) copolymer as compatibilizer and a transition metal salt as oxo-biodegradation promoter. The hybrid composites and relevant Lignin-free blends were formulated by following a statistical mixture design. The effect of Lignin, pro-degradant additive, EVA copolymer and their compatibility with the PE continuous matrix, was evaluated by means of structural features by attenuated total reflectance, morphological by scanning electron microscopy, thermal by differential scanning calorimetry and thermo-gravimetric analysis and mechanical properties by an Instron Machine. The results attained in this study, regarding especially the thermal and mechanical properties, suggest that bio-based oxo-biodegradable hybrid composites offer an interesting way to produce low cost bio-based materials with fairly enhanced properties. The moderate-low cost hybrid materials appear to be attractive for their potential in the mercantile area of commodities including: packaging, personal care products, agricultural mulch films and disposable items. This will constitute a novel added-value contribution aimed at mitigating the environmental burden caused by plastic waste items improperly abandoned in the environment.     

Synthesis,Characterization and NH<Subscript>3</Subscript>/N<Subscript>2</Subscript> Gas Permeation Study of Nanocomposite Membranes

Carbon nanotubes have exceptional mechanical properties which make them very attractive for the development of composite membranes. In this research, NH₃/N₂ gas permeation behavior of flat sheet composite membranes was examined. The cellulose acetate-multiwalled carbon nanotubes composite membranes were synthesized using solution casting method. The morphology and dispersion of carbon nanotubes were observed through SEM. However, the composite membranes were also characterized using several analytical techniques such as X-ray diffraction analysis, tensile testing analysis, and thermal gravimetric analysis. Characterization of these membranes depicted that carboxylic group functionalized MWCNTs are extremely compatible with CA. The permeation experiments were performed with NH₃ and N₂ to explore the host–guest interaction of MWCNTs with chosen gases. The permeability of NH₃ was found pronounced compared to N₂. The NH₃/N₂ selectivity up to 90 was documented.     

Processing and Properties of Mixtures of PHB-V with Post-consumer LDPE

Mixtures of poly-β-(hydroxybutyrate-co-valerate) PHB-V with virgin and post-consumer low density polyethylene (LDPE) were prepared by melt mixing in proportions of 100/0, 90/10, 80/20, 70/30 and 0/100 (wt/wt%). The mixtures were analysed by infrared spectroscopy, differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), melting flow index (MFI), tensile tests, scanning electron microscopy (SEM) and biodegradation in simulated soil. The DMTA and DSC curves of post-consumer LDPE suggested that this polymer was a mixture of LDPE and linear low density polyethylene (LLDPE). Virgin and post-consumer LDPE had lower MFI than PHB-V, but the blends showed higher index as the content of LDPE increased. The addition of LDPE reduced the tensile strength and Young’s modulus of the mixtures compared with PHB-V. SEM indicated poor interfacial adhesion between PHB-V and LDPE. PHB-V degraded slow and gradually, while both LDPE showed virtually no degradation under the conditions studied. The biodegradability of the blends depended on their composition and of the type of LDPE. LDPE improved the biodegradability of the mixtures.     

Green Synthesis of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/Cellulose/Polyvinyl Alcohol Hybride Aerogel and Its Application for Dye Removal

A novel Fe₃O₄/cellulose–polyvinyl alcohol (PVA) aerogel was successfully synthesized by an eco-friendly and facile method in this work. Cellulose/PVA matrix was prepared through an environmental friendly physical cross-linking process and further in-situ decorated with Fe₃O₄. Series of Fe₃O₄ decorated aerogels were prepared and the effects of Fe₃O₄ nanoparticles (NPs) on the aerogels were systematic investigated. As-prepared aerogels exhibited desirable properties including nanostructure, relatively high porosity, improved mechanical and superparamagnetism. The TEM results showed that Fe₃O₄ NPs were integrated in the three-dimensional matrix of cellulose/PVA with a diameter of 9–12 nm. Furthermore, the mechanical strength of the aerogels was significantly enhanced after the introduction of Fe₃O₄ NPs. Meanwhile, the obtained Fe₃O₄/cellulose/PVA aerogel exhibited excellent adsorption performance toward methyl blue dye, and can be reused through fenton-like catalysts oxidative degradation of organic dye in H₂O₂ solution. Therefore, they will have a great potential application as eco-friendly and economical adsorbents.     

A Comparative Study of Doum fiber and Shrimp Chitin Based Reinforced Low Density Polyethylene Biocomposites

The aim of this paper was to study the effects of reinforcing low density polyethylene (LDPE) by using bio-fillers (Doum cellulose or Shrimp chitin) on the mechanical properties. Both, Doum cellulose extracted frsom Doum leaves and Shrimp chitin extracted from shrimp co-products were compounded with LPDE without and with compatibilizer. The biocomposites were prepared by melt blending in a twin-screw extruder. Torsion and flexural tests were performed to investigate the impact of each reinforcement on the biocomposite mechanical properties. The SEM was carried out to study the filler/polymer interface adhesion. The present study has demonstrated that Doum fibers and shrimp chitin succeed in improving the mechanical properties of LPDE bio-composites. The results also showed that the use of maleic anhydride-grafted polyethylene as a compatibilizer improves filler adhesion/matrix and mechanical properties. This study exhibits that polyethylene composites based on Doum fibers or shrimp chitin can be used to replace the polyethylene materials in several fields like packaging and automotive industries.     

Microbial Degradation of UV-Pretreated Low-Density Polyethylene Films by Novel Polyethylene-Degrading Bacteria Isolated from Plastic-Dump Soil

Eleven effective low-density polyethylene (LDPE)-degrading bacterial strains were isolated and identified from landfill soil containing large amounts of plastic materials. The isolates belonged to 8 genera, and included Pseudomonas (areroginosa and putida), Sphingobacterium (moltivorum), Delftia (tsuruhatansis), Stentrophomonas (humi and maltophilia), Ochrobacterum (oryzeae and humi), Micrococcus (luteus), Acinetobacter (pitti), and Citrobacter (amalonaticus). Abiotic degradation of LDPE films by artificial and natural ultraviolet (UV)-exposure was analyzed by FT-IR spectroscopy. LDPE films treated with UV-radiation were also inoculated with the isolates and biofilm production and LDPE degradation were measured. Surface changes to the LDPE induced by bacterial biofilm formation were visualized by Scanning Electron Microscopy. The most active bacterial isolate, IRN19, was able to degrade polyethylene film by 26.8?±?3.04% gravimetric weight over 4 weeks. Analysis of 16S rRNA sequence of this isolate revealed 96.97% similarity in sequence to Acinetobacter pitti, which has not previously been identified as a polyethylene-degrading bacterium. Also, most the effective biofilm forming isolate, IRN11, displayed the highest cell mass production (6.29?±?0.06 log cfu/cm²) after growth on LDPE films, showed 98.74% similarity to Sphingobacterium moltivourum.     

Effect of Recycling on Material Properties of Glass-filled Polyethylene Terephthalate

Recycled plastics are considered low performance materials because their properties are expected to decrease drastically with recycling. The objective of this study was to characterize a 15 wt.% glass filled polyethylene terephthalate (rPET-15GF) using six recycle generations and four recycle ratios. Mechanical properties such as tensile strength, elastic modulus, and percent elongation to failure of the PET composite were determined for various recycle generations and recycle ratios. Results show that the mechanical properties of rPET-15GF decrease slightly per recycle generation. In contrast, thermal properties of rPET-15GF were not at all affected by the recycling process. This data demonstrates that recycled glass filled PET can be used effectively to fabricate components without significantly affecting their mechanical performance.     

Reductive decomposition of waste gypsum with SiO<Subscript>2</Subscript>, Al<Subscript>2</Subscript>O<Subscript>3</Subscript>, and Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> additives

From the point of view of a sustainable and environment-friendly society based on the recycling of material resources, it is preferable to utilize waste gypsum as a substitute for lime, which is currently produced by the calcination of limestone. In the present work, the reductive decomposition of CaSO₄ was investigated under an atmosphere of CO: 2 vol%, CO₂: 30 vol%, with N₂ as a carrier gas without and with the addition of SiO₂, Al₂O₃, or Fe₂O₃. It was found that the decomposition temperature of CaSO₄ was significantly reduced from 1673 K to 1223 K when only 5 wt% Fe₂O₃ was added to CaSO₄. In the case of the addition of SiO₂ or Al₂O₃ to CaSO₄, the decomposition temperature was reduced from 1673 K to 1623 K. This was due to the formation of composite oxides (calcium ferrite, calcium silicate, or calcium aluminate) during the reaction of CaSO₄ with the additives at a lower temperature. In addition, the formation of unfavorable product CaS was inhibited in the presence of 5 wt% Fe₂O₃, and this inhibition effect further increased as the addition of Fe₂O₃ was increased. In contrast, no significant effect on the inhibition of CaS formation was observed on the addition of SiO₂ or Al₂O₃.     

Biodegradability and Thermal Properties of Novel Natural Rubber/Linear Low Density Polyethylene/Thermoplastic Starch Ternary Blends

This work aimed to prepare biodegradable thermoplastic elastomers based on NR/LLDPE/TPS ternary simple blends to achieve some exclusive properties, i.e., good biodegradability in terms of water absorption and weight loss after burial, together with reasonable mechanical and thermal properties. A comparative study on biodegradability and other related properties of NR/LLDPE binary and NR/LLDPE/TPS ternary blends was performed. It was found that increasing the TPS proportion decreased storage modulus and complex viscosity. In addition, the size of dispersed TPS domains in the NR/LLDPE co-continuous matrix increased with TPS proportion, while the mechanical properties in terms of 100% moduli, tensile strength, elongation at break, and hardness decreased. This might be attributed to decreased interfacial adhesion with increasing size of TPS domains. Furthermore, increasing the TPS loading in the blend reduced the temperatures for 5 or 50% mass loss (T₅ or T₅₀) and the degradation temperature (T _d ). However, the biodegradability improved, in terms of increased water absorption and weight loss after burial in soil, with the loading level of TPS.     

Molecular Transport of Xylene Through Palm Pressed Fibre Filled Low Density Polyethylene: Role of Fibre Content,Alkali Treatment and Particle Size

We report in this paper the transport of an aromatic solvent, xylene through palm pressed fibre filled low density polyethylene composites studied at three different temperatures (40, 60, and 80 °C) by conventional weight-gain method. The diffusion parameters were investigated with special reference to the effect of fibre content, temperature and particle size. The effect of alkali treatment on solvent uptake was also analyzed. The transport coefficients of diffusion, permeation and sorption were determined to evaluate the influence of interface bonding on transport properties. The van’t Hoff relationship was used to determine the thermodynamic parameters and was found that the estimated free energies of sorption were all positive, indicating non-spontaneity of the solubility of PPF/LDPE composites. The first order kinetic rate constant and swelling parameters were also evaluated.     

Biodegradable Composite Foams of PLA and PHBV Using Subcritical CO<Subscript>2</Subscript>

One key strategy for increasing the application potential for biodegradable plastics lies in improving the physical and mechanical characteristics, which can be attained by inducing a cellular morphology in the pure polymer with the aid of a blowing agent, as well as by blending two or more polymers with the desirable properties. This paper examines the effect that blending two biodegradable polymers has on the thermal properties and morphology of the resultant foams blown with carbon dioxide (CO₂). Polylactic acid (PLA), polyhydroxybutyrate-co-valerate (PHBV) and blends of both were foamed and characterized in terms of thermal characteristics, relative density, cell size, and foam morphology. The results indicate that although PLA and PHBV are immiscible, the presence of small quantities of PHBV (25 wt%) could lead to low density foams with finer, more uniform cells. Furthermore, the crystallinity of PHBV was found to be unaffected by the presence of PLA in the composite, which supports the immiscibility of PLA and PHBV.     

Thermoplastic Blends from Albumin and Zein: Plastic Formation and Mechanical Properties Including Modeling

The use of proteins in blending with traditional polymers in the formation of thermoplastics can produce plastics with properties that are superior to traditional petroleum-based plastics. We investigated the physical and thermal properties of albumin and zein thermoplastic blends plasticized with glycerol and mixed with varying amounts of low-density polyethylene (LDPE). Several mechanical models were utilized to determine how tensile properties will be altered when varying amounts of protein/LDPE were added into the thermoplastic blend. When analyzed for thermal properties, we found that as the amount of LDPE in the thermoplastic blend increased, the resulting plastic possessed thermal properties that were more similar to pure LDPE plastics. In terms of mechanical properties, comparison between the experimental data and model predictions points to a synergistic effect between albumin and LDPE that leads to higher modulus, while a potential lack of compatibility between zein and LDPE leads to a plastic with lower modulus. Based on our results, the use of albumin and zein proteins when blended with LDPE in the production of thermoplastics has potential use in the areas of medical and food packaging applications.     

Production of natural and recycled aggregates: the environmental impacts of energy consumption and CO<Subscript>2</Subscript> emissions

Natural aggregates (NA) are crushed and processed in crushing plants after the extraction stage in quarries. In the present study, the aggregates are divided into three scenarios, depending on the production methods. The first scenario considers the production of NA, the second scenario deals with the production of recycled aggregates (RA) with respect to construction and demolition waste, and the third scenario, which is a hybrid scenario, handles the combination of NA and RA by assuming a 50% mixing percentage. In this research, we assess the environmental impacts on the production of aggregates via each scenario, using life cycle assessment; in addition, energy consumption and CO₂ emissions are considered as the environmental variables. We conclude that Iran’s current policy with an annual energy consumption of 1.48 million tons of oil equivalent (toe) can have a footprint of 2.88 million tons of CO₂ eq emissions per year (the first scenario). Achieving 30 and 36% reduction in annual energy consumption and CO₂ emissions, respectively, by the third scenario compared to the first scenario indicates the destructive effect of the first scenario from the environmental outlook.