Co-digestion of sewage sludge with glycerol to boost biogas production

The feasibility of adding crude glycerol from the biodiesel industry to the anaerobic digesters treating sewage sludge in wastewater treatment plants was studied in both batch and continuous experiments at 35 °C. Glycerol addition can boost biogas yields, if it does not exceed a limiting 1% (v/v) concentration in the feed. Any further increase of glycerol causes a high imbalance in the anaerobic digestion process. The reactor treating the sewage sludge produced 1106 ± 36 ml CH₄/d before the addition of glycerol and 2353 ± 94 ml CH₄/d after the addition of glycerol (1% v/v in the feed). The extra glycerol-COD added to the feed did not have a negative effect on reactor performance, but seemed to increase the active biomass (volatile solids) concentration in the system. Batch kinetic experiments showed that the maximum specific utilization rate (μ_max) and the saturation constant (K_S) of glycerol were 0.149 ± 0.015 h^?1 and 0.276 ± 0.095 g/l, respectively. Comparing the estimated values with the kinetics constants for propionate reported in the literature, it can be concluded that glycerol uptake is not the rate-limiting step during the process.     

A novel process for recycling and resynthesizing LiNi1/3Co1/3Mn1/3O2 from the cathode scraps intended for lithium-ion batteries

To solve the recycling challenge for aqueous binder based lithium-ion batteries (LIBs), a novel process for recycling and resynthesizing LiNi_1/3Co_1/3Mn_1/3O₂ from the cathode scraps generated during manufacturing process is proposed in this study. Trifluoroacetic acid (TFA) is employed to separate the cathode material from the aluminum foil. The effects of TFA concentration, liquid/solid (L/S) ratio, reaction temperature and time on the separation efficiencies of the cathode material and aluminum foil are investigated systematically. The cathode material can be separated completely under the optimal experimental condition of 15 vol.% TFA solution, L/S ratio of 8.0 mL g^?1, reacting at 40 °C for 180 min along with appropriate agitation. LiNi_1/3Co_1/3Mn_1/3O₂ is successfully resynthesized from the separated cathode material by solid state reaction method. Several kinds of characterizations are performed to verify the typical properties of the resynthesized LiNi_1/3Co_1/3Mn_1/3O₂ powder. Electrochemical tests show that the initial charge and discharge capacities of the resynthesized LiNi_1/3Co_1/3Mn_1/3O₂ are 201 mAh g^?1 and 155.4 mAh g^?1 (2.8–4.5 V, 0.1 C), respectively. The discharge capacity remains at 129 mAh g^?1 even after 30 cycles with a capacity retention ratio of 83.01%.     

Oil Erosion in an Annular Flume by Seawater of Varying Turbidities: A Critical Bed Shear Stress Approach

Laboratory experiments were conducted in an annular flume using Hibernia crude oil to determine: (1) the critical shear stress (τ_c) necessary to remove stranded oil from a surface by resuspension and (2) the effect of suspended sediment concentrations (SSCs) on the oil erosion processes. Two types of erosion were evident: Type I––solution and erosion of soluble aromatics; and Type II––mass erosion of visible droplets. In particulate free seawater at 13 °C, the Type II erosion threshold τ_cII is 5.0 Pa. This is equivalent to a mean current velocity (U_y) of 0.55 m s⁻¹. At U_y values <0.55 m s⁻¹, Type I erosion occurred as shown by the increase of oil concentrations without visible erosion of the oil surface. Temperature has a strong control on the threshold and rate of oil erosion: the threshold for Type I erosion at 4 °C was higher and erosion rate lower than at 13 °C. No Type II erosion was observed at 4 °C. SSCs also affects the entrainment of oil. Oil erosion was most efficient at moderate SSCs. At very high SSCs, turbulence suppression and drag reduction became effective and oil erosion rate decreased. SSC at 200–250 mg l⁻¹ were observed to give maximum erosion efficiency and is therefore suggested as the optimal concentration for erosion and elimination of heavy crude oil at a water temperature of 13 °C.     

Changes in enzymatic activities and microbial properties in vermicompost of water hyacinth as affected by pre-composting and fungal inoculation: A comparative study of ergosterol and chitin for estimating fungal biomass

In this experiment, three different fungal species, viz. Trichoderma viridae, Aspergillus niger and Phanerochaete chrysosporium, were inoculated in 7 day and 15 day partially decomposed water hyacinth to study their effect on enzymatic activities, microbial respiration and fungal biomass of the final stabilized product. The results suggested that increasing the duration of pre-composting from 7 days to 15 days did not show any significant effect on the activities of hydrolytic enzymes. Inoculation of fungi significantly (P ? 0.05) increased cellulase, protease and acid and alkaline phosphatase activities. The highest value of ergosterol was recorded in A. niger-inoculated vermicomposts. Inoculation of P. chrysosporium in initial organic waste registered the highest chitin content in vermicompost. A comparison of fungal biomass and chitin content revealed a conversion factor of 2.628 with a standard deviation of 0.318. Due to significant correlation (r = 0.864), this conversion factor allows for the calculation of fungal biomass from chitin, which is comparatively more stable than ergosterol.     

Microbial oxygen uptake in sludge as influenced by compost physical parameters

The wide range of optimal values reported for the physical parameters of compost mixtures suggest that their interactive relationships should be investigated. The objective of this study was to examine the microbial O₂ uptake rate (OUR) in 16 sludge waste recipes, offering a range of moisture content (MC), waste/bulking agent (W/BA) ratio and BA particle size levels determined using a central composite experimental design. The 3 kg samples were maintained at a constant temperature and aeration rate for 28 days, during which a respirometer recorded O₂ uptake to provide a measure of microbial activity and biodegradability. The cumulative O₂ consumption after 14 and 28 days was found to be significantly influenced by MC, W/BA ratio, BA particle size and the interaction between MC and W/BA ratio (p < 0.05). Using multivariate regression analysis, the experimental data was used to generate a model with good predictive ability for cumulative O₂ consumption after 28 days as a function of the significant physical variables (R² = 0.84). The prediction of O₂ uptake by the model depended highly on the interaction between MC and W/BA ratio. A MC outside of the traditional 50–60% (wet basis) range still resulted in a high level of microbial O₂ uptake as long as the W/BA ratio was adjusted to maintain a suitable O₂ exchange in the sample. The evolution of OUR in the samples was also investigated, uncovering strong associations between short and long-term respirometric indices, such as peak OUR and cumulative O₂ consumption (p < 0.005). Combining peak OUR data with cumulative O₂ consumption after 14 days allowed for accurate predictions of cumulative O₂ after 28 days of aeration (R² = 0.96), implying that future studies need only run trials up to 14 days to evaluate the overall O₂ consumption or biodegradability of similar sludge mixtures.     

What is the acceptable margin of error for the oxygen uptake method in evaluating the reactivity of organic waste?

The acceptable margin of error for the organic waste reactivity measured by the oxygen uptake method was assessed. Oxygen uptake was determined by the Dynamic Respiration Index (DRI) (mgO₂/kgVS h). The composed uncertainty (uC) of the experimental set up used for the DRI test was evaluated and the uncertainty (u) of all the components of the apparatus was evaluated. A procedure for calculating the uC of the apparatus is proposed. The components affecting the uC of the DRI to a more significant extent were the one of the oxygen mass rate and the u of the amount of VS in the sample analyzed. For a confidence level of 99.73%, the extended uC (UC) interval for a DRI = 1024 mgO₂/kgVS h was ±440 mgO₂/kgVS h, whereas for a DRI = 3489 mgO₂/kgVS h, the UC interval was ±1288 mgO₂/kgVS h. When oxygen consumption and VS content become lower than 600 mgO₂/h and 0.9 kg, respectively, the UC interval is similar to the measured DRI.     

Recovery of lithium and cobalt from waste lithium ion batteries of mobile phone

In view of the stringent environmental regulations, availability of limited natural resources and ever increasing need of alternative energy critical elements, an environmental eco-friendly leaching process is reported for the recovery of lithium and cobalt from the cathode active materials of spent lithium-ion batteries of mobile phones. The experiments were carried out to optimize the process parameters for the recovery of lithium and cobalt by varying the concentration of leachant, pulp density, reductant volume and temperature. Leaching with 2 M sulfuric acid with the addition of 5% H₂O₂ (v/v) at a pulp density of 100 g/L and 75 °C resulted in the recovery of 99.1% lithium and 70.0% cobalt in 60 min. H₂O₂ in sulfuric acid solution acts as an effective reducing agent, which enhance the percentage leaching of metals. Leaching kinetics of lithium in sulfuric acid fitted well to the chemical controlled reaction model i.e. 1 ? (1 ? X)^1/3 = k_ct. Leaching kinetics of cobalt fitted well to the model ‘ash diffusion control dense constant sizes spherical particles’ i.e. 1 ? 3(1 ? X)^2/3 + 2(1 ? X) = k_ct. Metals could subsequently be separated selectively from the leach liquor by solvent extraction process to produce their salts by crystallization process from the purified solution.     

An advanced study on the hydrometallurgical processing of waste computer printed circuit boards to extract their valuable content of metals

This study refers to two chemical leaching systems for the base and precious metals extraction from waste printed circuit boards (WPCBs); sulfuric acid with hydrogen peroxide have been used for the first group of metals, meantime thiourea with the ferric ion in sulfuric acid medium were employed for the second one. The cementation process with zinc, copper and iron metal powders was attempted for solutions purification. The effects of hydrogen peroxide volume in rapport with sulfuric acid concentration and temperature were evaluated for oxidative leaching process. 2 M H₂SO₄ (98% w/v), 5% H₂O_2, 25 °C, 1/10 S/L ratio and 200 rpm were founded as optimal conditions for Cu extraction. Thiourea acid leaching process, performed on the solid filtrate obtained after three oxidative leaching steps, was carried out with 20 g/L of CS(NH₂)₂, 6 g/L of Fe³⁺, 0.5 M H₂SO₄, The cross-leaching method was applied by reusing of thiourea liquid suspension and immersing 5 g/L of this reagent for each other experiment material of leaching. This procedure has lead to the doubling and, respectively, tripling, of gold and silver concentrations into solution. These results reveal a very efficient, promising and environmental friendly method for WPCBs processing.     

A comparative study of two composts as filter media for the removal of gaseous reduced sulfur compounds (RSCs) by biofiltration: Application at industrial scale

This work presents the use of two composts as filter media for the treatment by biofiltration of odors emitted during the aerobic composting of a mixture containing sewage sludge and yard waste. The chemical analysis of the waste gas showed that the malodorous compounds at trace level were the reduced sulfur compounds (RSCs) which were dimethyl sulfide (Me₂S), methanethiol (MeSH) and hydrogen sulfide (H₂S). Laboratory tests for biofiltration treatment of RSCs were performed in order to compare the properties of two filter media, consisted of a mature compost with yard waste (YW) and a mixture of mature compost with sewage sludge and yard waste (SS/YW). The maximum elimination capacity (EC) values obtained with the YW mature compost as packing material were 12.5 mg m^?3 h^?1 for H₂S, 7.9 mg m^?3 h^?1 for MeSH and 34 mg m^?3 h^?1 for Me₂S, and the removal efficiency decreased in the order of: H₂S > MeSH > Me₂S. Moreover, the YW compost filter medium had a better behavior than the filter medium based on SS/YW in terms of acclimation of the microbial communities and moisture content. According to these results, a YW mature compost as packing material for an industrial biofilter were designed and this industrial biofilter was found effective under specified conditions (without inoculation and addition of water). The results showed that the maximum EC value of RSCs was 935 mg m^?3 h^?1 (100% removal efficiency, RE) for an inlet loads (IL) between 0 and 1000 mg m^?3 h^?1. Thus, YW compost medium was proven efficient for biofiltration of RSCs both at laboratory and industrial scale.     

The usability of the IR,RAC and MRI indices of heavy metal distribution to assess the environmental quality of sewage sludge composts

To assess the environmental quality of compost, it is insufficient to use only total metal concentration. Therefore in this study, the stability of metals in compost and the environmental risk they pose were assessed by three indices that have been proposed for soils or sediments: the I_R, the RAC and the MRI. In mature composts, the highest bonding intensity was for Ni (0.79 < I_R < 0.93), then for Cu (0.56 < I_R < 0.65) and Pb (0.55 < I_R < 0.73), and the lowest for Zn (0.19 < I_R < 0.25). Although, both the I_R and the RAC are useful indices for evaluating the mobility of metals, they do not take into account their toxicity. Therefore, the overall classification of compost should also include the MRI, at which metal toxicity from the most available fractions is considered. Based on the MRI ranged between 10.0 and 11.6, all composts evaluated posed a low risk.     

Pathogen reduction in minimally managed composting of bovine manure

Spread of manure pathogens is of considerable concern due to use of manure for land application. In this study, the effects of four static pile treatment options for bovine manure on die-off of a generic Escherichia coli, E. coli O157:H7 surrogate, Salmonella Senftenberg, Salm. Typhimurium, and Listeria monocytogenes were evaluated. Bovine manure spiked with these bacteria were placed in cassettes at the top, middle, and bottom sections of four static pile treatments that reflect minimal changes in pile construction with and without straw. Temperatures were monitored continuously during the 28 day self-heating period. E. coli and salmonellae were reduced from 8 to 9 log₁₀ CFU g^?1 to undetectable levels (<1.77 log₁₀ MPN g^?1) at 25–30 cm depths within 7 days in all pile sections except for the manure-only pile in which 3–4 logs of reduction were obtained. No L. monocytogenes initially present at 6.62 log₁₀ CFU g^?1 were recovered from straw-amended piles after 14 days, in contrast with manure-only treatment in which this pathogen was recovered even at 28 days. Decline of target bacterial populations corresponded to exposure to temperatures above 45 °C for more than 3 days and amendments of manure with straw to increase thermophilic zones. Use of straw to increase aeration, self-heating capacity, and heat retention in manure piles provides producers a minimal management option for composting that enhances pathogen die-off and thereby reduces risk of environmental spread when manure is applied to land.     

Washing treatment of automotive shredder residue (ASR)

Worldwide, the amount of end-of-life vehicles (ELVs) reaches 50 million units per year. Once the ELV has been processed, it may then be shredded and sorted to recover valuable metals that are recycled in iron and steelmaking processes. The residual fraction, called automotive shredder residue (ASR), represents 25% of the ELV and is usually landfilled. In order to deal with the leachable fraction of ASR that poses a potential threat to the environment, a washing treatment before landfilling was applied. To assess the potential for full-scale application of washing treatment, tests were carried out in different conditions (L/S = 3 and 5 L/kg_TS; t = 3 and 6 h). Moreover, to understand whether the grain size of waste could affect the washing efficiency, the treatment was applied to ground (<4 mm) and not-ground samples. The findings obtained revealed that, on average, washing treatment achieved removal rates of more than 60% for dissolved organic carbon (DOC), chemical oxygen demand (COD) and total Kjeldahl nitrogen (TKN). With regard to metals and chlorides, sulphates and fluoride leachable fraction, a removal efficiency of approximately 60% was obtained, as confirmed also by EC values. The comparison between the results for ground and not-ground samples did not highlight significant differences.     

An innovative example of herb residues recycling by gasification in a fluidized bed

A utilization way of herb residues is designed to convert herb residues to gas fuel in industrial-scale by a circulating fluidized bed gasifier in this paper. The product gas is used in the production of Chinese medicine, and the heat of the flue gas from the boiler can be used in herb residues drying to realize the energy recycling and no herb residues discharge. The gasification characteristics of herb residues in the circulating fluidized bed of 300 kg/h were investigated for about 200 h. The results indicated that the gas composition and tar yield were affected by biomass flow rate, equivalence ratio (ER), moisture content and char circulating. The lower heating value of product gas was 4–5 MJ/m³ using herb residues as feedstock. When mean biomass flow rate was at 5.5 kg m^?2 s^?1 and ER at 0.35, the product gas reached a good condition with lower heating value of 4.89 MJ/m³ and cold gas efficiency of 62.36%. When the moisture content changed from 12.5% to 18.7%, the concentrations of H₂, CO and CO₂ changed from 4.66% to 6.92%, 11.23% to 10.15%, and 16.55% to 17.82% respectively, and the tar content in gas decreased from 15.1 g/m³ to 14.4 g/m³ when the moisture content increased from 12.5% to 15.4%. There are metal oxides in the ash of herb residues, especially CaO, MgO, K₂O, Al₂O₃, and Fe₂O₃ which have obvious function on tar catalytic decomposition. The ash that attaches to the char particles can decrease the tar yield and improve the quality of gas after returning to the gasifier.     

Thermo-chemical extraction of fuel oil from waste lubricating grease

This study investigated the recovery of oil from waste grease through the process of thermal degradation in an aqueous solution of potassium hydroxide (KOH) followed by solvent extraction. Waste high temperature metal bearing grease was dissolved in a 15 w/w% KOH solution at 80 °C while being agitated at 2000 rpm using a shear action agitator for a period of 15 min. Two distinct layers were observed after 8 min of settling time. The top layer being of dark brown oil and the bottom layer was a heterogeneous mixture. The two layers were separated by decantation. The bottom layer was cooled down to 45 °C followed by slow addition of toluene (C₇H₈) while agitating at 1200 rpm for 15 min to prevent solids settling and minimise rapid volatilisation of the organic compounds in the mixture. Two distinct layers were also formed, the top homogeneous mixture of light brown oil–toluene mixture and the bottom sludge layer. The solvent was recovered from the oil for re-use by fractional distillation of the homogenous mixture. It was observed that 15 w/w% potassium hydroxide solution can chemically degrade the soap matrix in the grease and extract up to 49 w/w% of the fuel oil when subjected to high shear stress at a temperature of 80 °C. The 26 w/w% extraction of oil in the remaining sludge was obtained by solvent extraction process with mass ratios of sludge to solvent of 2:1. Solvent recovery of 88% by mass was obtained via fractional distillation method. The combined extraction processes brought an overall oil yield of 75 w/w% from the waste grease. The fuel oil obtained from this process has similar properties to paraffin oil and can be blended with other oils as an alternative energy source.     

Emission of volatile sulfur compounds during composting of municipal solid waste (MSW)

Volatile sulfur compounds (VSCs) are the main source for malodor from composting plants. In this study, the VSCs generated from composting of 15–80 mm municipal solid waste (T0), kitchen waste (T1) and kitchen waste mixed dry cornstalks (T2) were measured in 60 L reactors with forced aeration for a period of 30 days. The VSCs detected in all treatments were hydrogen sulfide (H₂S), methyl mercaptan (MM), dimethyl sulfide (DMS), carbon bisulfide (CS₂) and dimethyl disulfide (DMDS). Over 90% of the VSCs emissions occurred during the first 15 days, and reached their peak values at days 4–7. The emission profiles of five VSCs species were significantly correlated with internal materials temperature and outlet O₂ concentration (p < 0.05). Total emissions of the VSCs were 216.1, 379.3 and 126.0 mg kg^?1 (dry matter) for T0, T1 and T2, respectively. Among the five VSCs, H₂S was the most abundant compound with 39.0–43.0% of total VSCs released. Composting of kitchen waste from separate collection posed a negative influence on the VSC and leachate production because of its high moisture content. An addition of dry cornstalks at a mixing ratio of 4:1 (wet weight) could significantly reduce the VSCs emissions and avoid leachate. Compared to pure kitchen waste, VSCs were reduced 66.8%.     

Thermogravimetric analysis and kinetic study on large particles of printed circuit board wastes

Pyrolysis of large printed circuit board (PCB) waste particle was conducted on a specially designed laboratory-scale thermobalance (Macro-TG) with sample loading of 30 g under dynamic nitrogen atmosphere. The effects of heating rate (10, 15, 20 and 25 °C min^?1) and particle size (1 mm × 1 mm, 5 mm × 5 mm, 10 mm × 10 mm and 10 mm × 20 mm) were examined. To compare the different decomposition behavior of fine and large one, the thermal decomposition of PCB waste powder (approximately 5 mg) was also performed on a thermogravimetric analyzer (common TG) under various heating rates (10, 15, 20 and 40 °C min^?1) and particle size ranges (0.198–0.165 mm, 0.165–0.074 mm, 0.074–0.055 mm and 0.055–0.047 mm). Experimental results show that large particle has a pyrolysis reaction retardancy compared to fine one. The distributed activation energy model was used to study the pyrolysis kinetics. It was found that during pyrolysis process, values of frequency factor (k₀) changed with different activation energy (E) values. On common TG, the E values range from 156.95 to 319.37 kJ mol^?1 and k₀ values range from 2.67 × 10¹³ to 2.24 × 10²⁷ s^?1. While, on Macro-TG, the range of E was 31.48–41.26 kJ mol^?1 and of the frequency factor was 19.80–202.67 s^?1.     

Potential of anaerobic digestion for material recovery and energy production in waste biomass from a poultry slaughterhouse

This study was carried out to assess the material and energy recovery by organic solid wastes generated from a poultry slaughterhouse. In a poultry slaughterhouse involving the slaughtering of 100,000 heads per day, poultry manure & feather from the mooring stage, blood from the bleeding stage, intestine residue from the evisceration stage, and sludge cake from the wastewater treatment plant were discharged at a unit of 0.24, 4.6, 22.8, and 2.2 Mg day^?1, consecutively. The amount of nitrogen obtained from the poultry slaughterhouse was 22.36 kg 1000 head^?1, phosphate and potash were 0.194 kg 1000 head^?1 and 0.459 kg 1000 head^?1, respectively. As regards nitrogen recovery, the bleeding and evisceration stages accounted for 28.0% and 65.8% of the total amount of recovered nitrogen. Energy recovered from the poultry slaughterhouse was 35.4 N m³ 1000 head^?1 as CH₄. Moreover, evisceration and wastewater treatment stage occupied 88.1% and 7.2% of the total recovered CH₄ amount, respectively.     

Case study of landfill leachate recirculation using small-diameter vertical wells

A case study of landfill liquids addition using small diameter (5 cm) vertical wells is reported. More than 25,000 m³ of leachate was added via 134 vertical wells installed 3 m, 12 m, and 18 m deep over five years in a landfill in Florida, US. Liquids addition performance (flow rate per unit screen length per unit liquid head) ranged from 5.6 × 10^?8 to 3.6 × 10^?6 m³ s^?1 per m screen length per m liquid head. The estimated radial hydraulic conductivity ranged from 3.5 × 10^?6 to 4.2 × 10^?4 m s^?1. The extent of lateral moisture movement ranged from 8 to 10 m based on the responses of moisture sensors installed around vertical well clusters, and surface seeps were found to limit the achievable liquids addition rates, despite the use of concrete collars under a pressurized liquids addition scenario. The average moisture content before (51 samples) and after (272 samples) the recirculation experiments were 23% (wet weight basis) and 45% (wet weight basis), respectively, and biochemical methane potential measurements of excavated waste indicated significant (p < 0.025) decomposition.     

Building a better methane generation model: Validating models with methane recovery rates from 35 Canadian landfills

The German EPER, TNO, Belgium, LandGEM, and Scholl Canyon models for estimating methane production were compared to methane recovery rates for 35 Canadian landfills, assuming that 20% of emissions were not recovered. Two different fractions of degradable organic carbon (DOC_f) were applied in all models. Most models performed better when the DOC_f was 0.5 compared to 0.77. The Belgium, Scholl Canyon, and LandGEM version 2.01 models produced the best results of the existing models with respective mean absolute errors compared to methane generation rates (recovery rates + 20%) of 91%, 71%, and 89% at 0.50 DOC_f and 171%, 115%, and 81% at 0.77 DOC_f. The Scholl Canyon model typically overestimated methane recovery rates and the LandGEM version 2.01 model, which modifies the Scholl Canyon model by dividing waste by 10, consistently underestimated methane recovery rates; this comparison suggested that modifying the divisor for waste in the Scholl Canyon model between one and ten could improve its accuracy. At 0.50 DOC_f and 0.77 DOC_f the modified model had the lowest absolute mean error when divided by 1.5 yielding 63 ± 45% and 2.3 yielding 57 ± 47%, respectively. These modified models reduced error and variability substantially and both have a strong correlation of r = 0.92.     

Impact of nitrate-enhanced leachate recirculation on gaseous releases from a landfill bioreactor cell

This study evaluates the impact of nitrate injection on a full scale landfill bioreactor through the monitoring of gaseous releases and particularly N₂O emissions. During several weeks, we monitored gas concentrations in the landfill gas collection system as well as surface gas releases with a series of seven static chambers. These devices were directly connected to a gas chromatograph coupled to a flame ionisation detector and an electron capture detector (GC-FID/ECD) placed directly on the field. Measurements were performed before, during and after recirculation of raw leachate and nitrate-enhanced leachate. Raw leachate recirculation did not have a significant effect on the biogas concentrations (CO₂, CH₄ and N₂O) in the gas extraction network. However, nitrate-enhanced leachate recirculation induced a marked increase of the N₂O concentrations in the gas collected from the recirculation trench (100-fold increase from 0.2 ppm to 23 ppm). In the common gas collection system however, this N₂O increase was no more detectable because of dilution by gas coming from other cells or ambient air intrusion. Surface releases through the temporary cover were characterized by a large spatial and temporal variability. One automated chamber gave limited standard errors over each experimental period for N₂O releases: 8.1 ± 0.16 mg m^?2 d^?1 (n = 384), 4.2 ± 0.14 mg m^?2 d^?1 (n = 132) and 1.9 ± 0.10 mg m^?2 d^?1 (n = 49), during, after raw leachate and nitrate-enhanced leachate recirculation, respectively. No clear correlation between N₂O gaseous surface releases and recirculation events were evidenced. Estimated N₂O fluxes remained in the lower range of what is reported in the literature for landfill covers, even after nitrate injection.