微波辐照修复氯丹污染土壤的影响因素

采用微波辐照技术修复氯丹污染土壤,以氯丹的挥发率和分解率为主要评价指标,研究了微波辐照条件对土壤修复效果的影响。实验结果表明:氯丹的挥发率随微波辐照功率的增大而增大,而氯丹的分解率则无明显变化;当活性炭与土壤质量比为9∶120时,氯丹的去除效果最好,去除率达89%;氯丹的挥发性能在前20min内随微波辐照时间的延长而增强,而氯丹的分解性能则刚好相反;当土壤含水率为15%时,氯丹的挥发率最高,为2.5%,而氯丹分解率最小,为16.8%;在酸性偏中性范围内氯丹的去除效果较差,随土壤p H的不断增大,氯丹的挥发率明显升高,且氯丹的分解率也增大。     

复合重金属污染高岭土的电动修复

根据电子废弃物拆解场地的污染特征,以复合重金属(Cu,Cd,Pb)污染高岭土为研究对象,考察了电动技术对污染土壤的修复效果。实验结果表明:在电压梯度为1 V/cm、阳极液为自来水、阴极液为柠檬酸-柠檬酸钠缓冲液(pH=5)、靠近阴极设置活性炭渗透反应墙(PRB)的条件下电动修复96 h后,Cu,Cd,Pb的平均去除率分别可达79.93%,99.43%,39.36%;土壤的酸碱性对电动修复效果影响显著,通过在阴极添加缓冲液维持土壤偏酸性条件,有利于重金属污染物的电动去除;在靠近阴极设置活性炭PRB可富集重金属,减少阴极液的污染;迁移率大的酸可提取态重金属较易去除,残渣态重金属稳定性强,去除率较低。     

电动力修复铅镉复合污染土壤

采用电动力修复技术处理Pb、Cd复合污染土壤,考察了柠檬酸和乙二胺四乙酸二钠（EDTA）作为电解液对棕壤（ZR）和红壤（HR）两种我国典型壤质中Pb、Cd去除效果的影响。实验结果表明：在电压梯度为2 V/cm,修复时间为4 d的条件下,ZR的最佳电解液为EDTA,Pb、Cd平均去除率为13.2%和17.8%,HR的最佳电解液为柠檬酸,Pb、Cd的平均去除率为20.0%和33.8%;延长修复时间至10 d能显著提高HR中Pb、Cd的去除率,电解液为柠檬酸时Cd平均去除率达91.1%,电解液为EDTA时Pb平均去除率达63.2%,修复后土壤中Cd和Pb含量均低于建筑用地土壤污染风险筛选值。综合考虑能耗及修复效果,EDTA是高效且经济的修复电解液。     

生物刺激与生物强化联合修复柴油污染土壤

从柴油污染土壤中筛选分离出一株高效降解柴油的菌株CY-1,考察了自然衰减修复、生物刺激修复、生物强化修复以及生物刺激-生物强化联合修复等4种修复方法对土壤中柴油的降解能力及降解过程中几种土壤微生物酶活性的变化。实验结果表明:该菌为假单胞菌属;采用生物刺激-生物强化联合修复初始柴油质量分数为2.70%的柴油污染土壤,经过31 d的降解,柴油质量分数降至1.09%,柴油去除率达59.6%;经生物刺激-生物强化联合修复,土壤脱氢酶活性和荧光素二乙酸酯水解酶活性最高;通过生物刺激处理可使土壤脲酶活性和磷酸酶活性达到最高。     

土壤残留塑料的热降解脱附研究

针对土壤的塑料污染问题,提出一种采用热脱附降解技术修复污染土壤的方法。选取4种土壤中常见的残留塑料（聚乙烯（PE）、聚氯乙烯（PVC）、聚对苯二甲酸乙二酯（PET）、聚丙烯（PP））为研究对象,通过控制热解温度和土壤含水率对各污染土壤的修复效果进行探究。实验结果表明：在500 ℃的最佳热解温度下处理60 min,PE、PVC、PET和PP的去除率分别达到92.61%、91.73%、90.74%和93.42%;土壤含水率低于16%时对修复效果的影响不显著。表征结果显示,500 ℃热解后土壤中残留有机成分已得到充分挥发,热解油的主要组分为烷烃。     

皂素和柠檬酸复合淋洗土壤中的钍

采用振荡淋洗和土柱动态淋洗实验研究了皂素和柠檬酸复合对土壤中钍的淋洗性能。实验结果表明:将质量浓度为20 g/L的皂素与浓度为20 mmol/L的柠檬酸以体积比1∶10配制复合淋洗液对污染土壤中钍的去除效果最佳,淋洗3.0 h,钍去除率为84.98%;准一级动力学方程能更好地描述复合淋洗液对钍的淋洗动力学特征;动态淋洗实验中当复合淋洗液用量为1 600 mL时,钍的累积去除量为73.66 mg/kg;淋洗后土壤中钍的酸可提取态、氧化结合态和有机结合态含量分别减少了79.63%、38.13%和20.34%,残渣态含量变化不大;淋洗后土壤中钍的稳定性增加。     

石油污染土壤的微生物修复技术

介绍了石油污染土壤微生物修复技术的影响因素;概述了生物刺激、生物强化、固定化微生物、植物-微生物联合修复以及电动-微生物联合修复石油污染土壤的技术原理,分析了现阶段土壤修复过程中面临的难题,预测了微生物修复技术的研究方向。指出优化微生物的环境条件、培育新型高效的基因工程菌和开发经济高效的新型修复技术等将是未来微生物修复技术的发展趋势。     

微波辐照处理高浓度邻苯二甲酸二辛酯生产废水

以活性炭为催化剂，采用微波辐照处理高浓度邻苯二甲酸二辛酯（DOP）生产废水，考察了各种因素对废水COD去除率的影响。实验结果表明，在活性炭加入量为30g/L、微波功率为400W、辐照时间为4min的条件下，COD去除率为86．3％。使用过的活性炭可用质量分数为20％的硫酸溶液浸泡，浸泡时间120min时，COD去除率最高（约为86％），再生后的活性炭可重复利用。反应动力学研究表明，该过程近似符合一级反应动力学规律。     

陕北某采油厂石油污染土壤的修复示范工程

调查了陕北某采油厂油井周边石油污染土壤的基本污染情况,采用铜绿假单胞菌-黑麦草联合修复技术对其进行了现场修复示范工程,取得了较好的现场修复效果。调查显示,该油井周边土壤的含油量最高为9 020 mg/kg。90 d的修复周期结束后,土壤的含油量降至402 mg/kg,去油率高达95.5%,并且不同采样位置的土壤含油量检测结果均低于500 mg/kg,满足《农用污泥污染物控制标准》（GB 4284—2018）中的A级土壤标准。单独使用黑麦草或铜绿假单胞菌进行修复,土壤的去油率分别为29.5%或88.8%,而空白区土壤的去油率仅为21.8%。     

氰化物污染土壤微生物修复方法初步研究

利用经过筛选和驯化的降氰菌处理氰化物污染土壤,实现氰化物的降解和去除,据此建立降氰菌修复含氰土壤的新方法。结果表明,降氰菌处理效果快速有效,经过3 d生物培养,氰化物降解率达到31.2%;随着培养时间延长,微生物群落代谢能力发生变化,在第3~8 d氰化物降解率增长缓慢,在第8 d达到33.3%。通过降氰菌种资源的筛选和应用,为氰化物污染土壤的修复提供了清洁、经济、有效的技术思路。     

絮凝#x02014;微波辐射#x02014;Fenton试剂氧化法深度处理焦化废水

用絮凝#x02014;微波辐射#x02014;Fenton试剂氧化法深度处理焦化废水，研究了微波辐射时间、微波功率、FeSO₄加入量、H₂O₂加入量和废水pH对废水处理效果的影响。实验结果表明：在聚合氯化铝加入量为350mg/L、聚丙烯酰胺加入量为12mg/L、废水pH=5、FeSO₄加入量为250mg/L、H₂O₂总加入量为1400mg/L、H₂O₂分3次投加、微波功率为400W、微波辐射时间为60min的条件下，处理后出水的浊度、色度和COD去除率分别为98.59%，97.62%，86.21%。处理后出水澄清透明，COD为50.34mg/L，满足GB50050#x02014;2007《工业循环冷却水处理设计规范》的要求。     

Impacts of microwave pretreatments on the semi-continuous anaerobic digestion of dairy waste activated sludge

Microwave (MW) irradiation is one of the new and possible methods used for pretreating the sludge. Following its use in different fields, this MW irradiation method has proved to be more appropriate in the field of environmental research. In this paper, we focused on the effects of MW irradiation at different intensities on solubilization, biodegradation and anaerobic digestion of sludge from the dairy sludge. The changes in the soluble fractions of the organic matter, the biogas yield, the methane content in the biogas were used as control parameters for evaluating the efficiency of the MW pretreatment. Additionally, the energetic efficiency was also examined. In terms of an energetic aspect, the most economical pretreatment of sludge was at 70% intensity for 12 min irradiation time. At this, COD solubilization, SS reduction and biogas production were found to be 18.6%, 14% and 35% higher than the control, respectively. Not only the increase in biogas production was investigated, excluding protein and carbohydrate hydrolysis was also performed successfully by this microwave pretreatment even at low irradiation energy input. Also, experiments were carried out in semi continuous anaerobic digesters, with 3.5 L working volume. Combining microwave pretreatment with anaerobic digestion led to 67%, 64% and 57% of SS reduction, VS reduction and biogas production higher than the control, respectively.     

微波紫外协同降解染料活性艳红X-3B研究

将微波激发的无极紫外灯应用于染料废水的处理研究,考察了反应过程中染料废水脱色率、TOC去除率、溶液pH以及反应前后染料废水高效液相色谱图的变化情况。染料活性艳红X-3B经无极紫外光处理110min后,脱色率达96％,TOC去除率达66％,降解效果明显好于单独使用微波或普通紫外灯的降解效果总和,溶液pH先降低后缓慢升高。     

微波催化氧化法处理甲基橙废水

采用微波催化氧化法处理模拟甲基橙废水,考察了微波功率、辐射时间、H2O2用量、活性炭用量对甲基橙去除率的影响。在微波功率630w、辐射时间9min、H2O2用量10mL／L,活性炭用量10g／L的条件下,甲基橙的去除率达到90％左右,并对实际染料废水、炼焦废水、炼油废水、餐饮废水进行了处理,取得了满意的结果。     

Combined thermal and zero‐valent iron In Situ soil mixing remediation technology

Thermal remediation of contaminated soils and groundwater by injection of hot air and steam using large‐diameter auger in situ soil mixing effectively remediates volatile and semivolatile organic compounds. This technology removes large amounts of contamination during the early treatment stages, but extended treatment times are needed to achieve high removal percentages. Combining thermal treatment with another technology that can be injected and mixed into the soil, and that continues to operate after removal of the drilling equipment, improves removal efficiency, and reduces cost. Using field‐determined pseudo first‐order removal rates, the cost of the combined remediation of chlorinated volatile organic compounds (CVOCs) by thermal treatment followed by reductive dechlorination by iron powder has been estimated as 57 percent of the cost of thermal treatment alone. This analysis was applied to a case‐study remediation of 48,455 cubic yards, which confirmed the cost estimate of the combined approach and showed over 99.8 percent removal of trichloroethene and other chlorinated VOCs. © 2010 Wiley Periodicals, Inc.     

Depolymerization of Waste PET with Phosphoric Acid–Modified Silica Gel Under Microwave Irradiation

Chemical recycling of waste poly(ethylene terephthalate) (PET) using phosphoric acid–modified silica gel as a solid catalyst is reported. Advantageously, microwave irradiation was used to progress the depolymerization of PET. In this study, depolymerization of PET with a small amount of water is suggested as a suitable method. The depolymerized product, terephthalic acid was obtained and assigned by ¹H NMR and FT-IR spectroscopy. Finally, over 90 % conversion to terephthalic acid was achieved when waste plastic bottles were treated with the method. This results confirm the importance of the microwave power technique as a promising recycling method for plastic bottles made from PET, resulting in monomer recovery in addition to substantial energy saving.