分子量和组成成分在渗滤液处理工艺中的变化

南方某垃圾焚烧厂产生的渗滤液采用"进水—厌氧—SBR—混凝—出水"的工艺进行处理。通过对各工艺单元出水进行分子量区分,并且测试各分子量区间的COD;测试渗滤液的组成成分在各工艺单元的含量。结果表明:该处理工艺对不同分子量区间COD去除效果较好,尤其对分子量2 k,去除率可达99%;对渗滤液的DOM组成成分腐殖酸(HA)、富里酸(FA)和亲水性有机质(HyI)的去除效果较好,去除率均达到88%以上。     

垃圾渗滤液处理技术

垃圾渗滤液是垃圾填埋过程中产生的高浓度有机废水,是国内外污水处理的一大难题.综述了垃圾渗滤液的水质特性,并总结了近年来在垃圾渗滤液的预处理、主体工艺及深度处理技术上的研究进展,对垃圾渗滤液处理技术提出研究方向.     

气相色谱法测定黄磷生产尾气中的CO_2

针对黄磷生产尾气具有强化学活性和腐蚀性的特点,选择了TDX-01型碳分子筛色谱柱,采用气相色谱法测定黄磷尾气中的CO2。实验结果表明:黄磷尾气中高浓度的CO2用TCD检测器检测,CO2体积分数在0.1%~10%时,检测下限可达到0.05%,方法的平均回收率为93.6%~104.1%,相对标准偏差为2.1%~3.2%;净化后黄磷尾气中的微量CO2经Ni催化甲烷化转化后用FID检测器测定,CO2体积分数在1.0×10-7~1.0×10-4时,方法的检测下限可达到5.0×10-8,相对标准偏差为1.63%。     

臭氧高级氧化技术在垃圾渗滤液领域的应用研究

垃圾填埋场渗滤液的处理一直是垃圾处理行业公认的难题之一,在膜法普遍应用后,带来了浓缩液的附加问题。从污染物的终端处置以及绿色无二次污染等方面出发,论证臭氧氧化系统对垃圾渗滤液的处理效果,寻求更好地解决现有问题的方案。通过对比分析小型垃圾渗滤液处理项目近一年的运营数据,发现臭氧去除COD的效率较高,配合以前端生化系统,可以实现渗滤液处理的稳定达标排放且无二次污染。     

AHP在人工湿地植物优化组合中的应用

介绍了可应用于垃圾渗滤液处理的三种人工湿地植物组合,并采用层次分析法从技术可行性、经济可行性、环境可行性三个方面对这三种组合进行了分析,得出了最优湿地植物组合为芦苇和凤眼莲组合.     

垃圾焚烧发电厂渗滤液处理站污泥危险特性研究

通过对一例垃圾焚烧发电厂渗滤液处理站污泥进行鉴定,表明该部分污泥不属于危险固废,可以纳入焚烧炉与生活垃圾一起处理。鉴别结果为促进固体废物循环利用及同类企业合理处置渗滤液处理站污泥提供了借鉴。     

煤化工废水中硫酸盐还原菌的分离及鉴定

从煤化工废水和厌氧污泥中分离出2株高效的硫酸盐还原菌,通过革兰氏染色、扫描电子显微镜观察其形态,通过16S r DNA序列分析法鉴定其种属,并研究其生长特性和硫酸盐还原性能。实验结果表明:菌株SRB-1为革兰氏阴性柠檬酸杆菌;菌株SRB-2为革兰氏阳性丁酸梭菌;两种菌株在最佳条件下培养4 d,菌液菌量均可达到1×106个/m L的水平;在SO2-4质量浓度为1 360 mg/L的条件下,两种菌株的SO2-4去除率分别达到93%和95%。     

提高三甲氧基苯甲醛医药中间体废水可生化性的研究

分别采用混凝、化学氧化和加Ca(OH)_2曝气的方法对三甲氧基苯甲醛(TMBA)生产废水进行处理。实验结果表明:混凝和化学氧化的方法未能明显改善TMBA废水的可生化性,而加Ca(OH)_2曝气的方法能明显改善TMBA废水的可生化性;当TMBA废水中Ca(OH)_2的质量浓度为20 g/L、曝气时间为3.0 h时,废水的COD去除率为35%,色度去除率达到90%,BOD_5/COD提高到0.35。     

电解法处理采油废水的研究

以提高电解处理工艺的效率、降低处理成本、易于实现工业化为目标,筛选出适合处理采油废水的高效电极材料,考察了电解法处理采油废水的各种影响因素,确定实验室电解氧化法处理采油废水的适宜条件.研究结果表明:以析氯阳极 铁阴极作为试验电极材料,在电流密度为15 mA/cm2,电解时间为80min,水板比约0.10 cm2/cm3,弱碱性,极板间距为10mm的条件下对采油废水进行电解处理,COD去除率可达到73.0%,NH3-N去除率可达到98.5%.     

节煤增效剂研制成功

开封市科委专利技术研究所研制的远征牌节煤增效剂 ,为解决我国工业各种锅窑炉耗煤量高、热效率低、劣质煤和煤泥利用率低、排放污染严重等问题是一大突破。据黑龙江省电力科学院等 1 0余省市节能部门的检测报告 ,在工业锅炉上使用该节煤增效剂 ,热效率可提高 1 5% ,50 0 t煤中添加 1 t节煤增效剂可节省原煤 1 0 0 t,煤渣含碳量下降 50 % ,烟硫排放量减少 30 %～ 6 0 %。使用劣质煤或优、劣混合煤可达到优质煤的燃烧效果 ,4 50 0大卡的煤可抵 6 0 0 0大卡的煤使用 ;在水泥生产生料配煤时使用该节煤增效剂 ,耗煤量可节省 2 0 %～ 30 % ,增产 …     

化学循环燃烧载氧体的研究进展

化学循环燃烧是集分离捕集CO2和去除NOx为一体的新型燃烧技术。介绍了化学循环燃烧的发展背景、工艺原理及特点；综述了化学循环燃烧载氧体的选材、载氧体的性能要求，对各系载氧体（如NiO系、Fe2O3系、CuO系、CoO系和Mn2O3系载氧体）的性能进行了对比分析；提出了Fe2O3、Fe2O3／Al2O3（质量分数为60％的Fe2O3＋质量分数为40％的Al2O3）、NiO／NiAl2O3（质量分数为50％的活性NiO＋质量分数为50％的NiAl2O3）是当前的优势载氧体，并对载氧体的发展做了展望。     

Mechanical,Barrier and Antioxidant Properties of Chitosan Films Incorporating Cinnamaldehyde

Chitosan films (CF) [1 and 2% w/v] alone and with cinnamaldehyde (CNE) [0.25, 0.5 and 1% v/v] were prepared using an emulsion method, and the obtained films were characterized in terms of water vapor permeability (WVP), water solubility and optical, mechanical and antioxidant properties. The incorporation of CNE at 1% (v/v) significantly decreased the water solubility of the film by approximately 4% for the 1 and 2% CF films, whereas the WVP increased (2.5–3.5 times). The incorporation of CNE (0.25 and 0.5%) into 2% CF significantly increased the tensile strength (TS) (62 and 34%, respectively) and the percent elongation (%E) values, 26, 30 and 52% for CF that contained 0.25, 0.5 and 1% CNE, respectively. The largest value of the elasticity modulus (EM) was observed for 2% CF with 0.25% CNE. All films exhibited a yellow appearance (b*), but the CNE content had a marked impact on the coloration of the films. The CNE recoveries of the CF films (1 and 2%) with 1% of CNE were high (43 and 67%). The antioxidant activities indicated that the incorporation of 1% CNE into CF films (1 and 2%) increased the antioxidant activity. The protective effects of the films with and without CNE on erythrocytes were very strong (36–72% hemolysis inhibition). These results suggest there are potential applications for CF-CNE films as active packaging for the preservation of food products.     

Chemical and physical characterization of electrode materials of spent sealed Ni-Cd batteries

The present work aimed at the chemical and physical characterization of spent sealed MONO-type Ni-Cd batteries, contributing to a better definition of the recycling process of these spent products. The electrode material containing essentially nickel, cadmium and some cobalt corresponds to approximately 49% of the weight of the batteries. The remaining components are the steel parts from the external case and the supporting grids (40%) containing Fe and Ni, the electrolyte (9%) and the plastic components (2%). Elemental quantitative analysis showed that the electrodes are highly concentrated in metals. The phase identification achieved by X-ray powder diffraction combined with chemical analysis and leaching tests allowed the authors to proceed with the composition of the electrode materials as following: cathode: 28.7% metallic Ni, 53.3% Ni(OH)2, 6.8% Cd(OH)2 and 2.8% Co(OH)2; anode: 39.4% metallic Ni and 57.0% Cd(OH)2. The morphology of the electrodes was studied by microscopic techniques and two phases were observed in the electrodes: (1) a bright metallic phase constituted of small nickel grains that acts as conductor, and (2) the main hydroxide phase of the active electrodes into which the nickel grains are dispersed. The disaggregation of the electrode particles from the supporting plates was easily obtained during the dismantling procedures, indicating that a substantial percentage of the electrodes can be efficiently separated by wet sieving after shredding the spent batteries.     

负载Pt对锐钛矿-板钛矿双相TiO_2光催化性能的影响

采用水热法合成了板钛矿-锐钛矿双相TiO_2,通过浸渍和氢还原法将贵金属Pt负载在双相TiO_2表面制成Pt/双相TiO_2催化剂。TEM表征结果显示:Pt/双相TiO_2催化剂中Pt的晶粒尺寸很小,晶粒尺寸分布较窄;低负载量(质量分数0.2%和2.0%)时,Pt晶粒在TiO_2表面分布非常均匀,Pt负载量达到4.0%时,Pt晶粒在TiO_2表面的分散性变差。光催化活性实验结果表明:负载Pt能显著提高双相TiO_2催化剂的甲基橙降解率;2.0%Pt/双相TiO_2催化剂的光降解性能最佳。光催化活性提高的主要原因是由于Pt颗粒的电子贮存能力促进了光生电子-空穴对的分离。     

焦化项目大气污染特征及环境影响评价

以甘肃省酒泉市阿克塞哈萨克族自治县某焦化项目为案例，在分析其工艺流程和排污环节的基础上，利用AERMOD模型定量预测评价该焦化项目对区域大气环境质量的影响程度。预测结果表明：SO2，NO2，NH3，H2S的区域最大地面小时质量浓度占标率分别为15.8%，29.6%，16.8%，24.8%;SO2、NO2、苯并[a]芘、固体悬浮物（TSP）的区域最大日均质量浓度占标率分别为7.5%，11.4%，7.2%，95.8%;TSP最大日均质量浓度坐标点为（500，0），位于厂界内部，高浓度是由焦化厂低矮面源造成的，且浓度随距离消减得较快。     

臭氧氧化—湿式钙法吸收工艺对烟气的同时脱硫脱硝

采用臭氧氧化—湿式钙法吸收工艺对模拟烟气进行同时脱硫脱硝处理。O₃于150 ℃下具有较高的热稳定性,可将NO氧化为高价态氮氧化物,且NO氧化率随n（O₃）∶n（NO）的增大而逐渐提高。烟气中SO₂和H₂O的存在对NO氧化率的影响不大。O₃对SO₂的氧化率较低,约为5%。3%（w）石灰石浆液对SO₂的吸收率接近100%,NO_x吸收率随n（O₃）∶n（NO）的增大而逐渐提高,当n（O₃）∶n（NO）为1.6时NO_x吸收率可达约65%。SO₂能促进吸收液对NO_x的脱除。石灰石浆液中加入0.2%（w）的（NH₄）₂SO₃或Na₂SO₃后NO_x吸收率可达约85%或82%,且吸收率随添加剂加入量的增加而提高,添加（NH₄）₂SO₃的NO_x吸收率略高于添加Na₂SO₃。     

A novel additive for the reduction of acid gases and NO(x) in municipal waste incinerator flue gas.

The reduction of SO2, HCl, and NO(x) concentrations using calcium magnesium acetate (CMA) as a novel sorbent in a simulated municipal waste incinerator flue gas was investigated. The reduction of individual SO2, HCl, and NO(x) concentrations was tested at 850 degrees C and it was found that CMA could reduce the SO2 concentration by 74%, HCl concentration by 64%, or NO(x) concentration by 94%. It was observed that individual SO2 or HCl capture increased with increasing initial oxygen concentration in the reacting gas or increasing sorbent input. NO(x) reduction decreased with increasing initial oxygen concentration in the reacting gas. The simultaneous reduction of SO2, HCl, and NO(x) concentrations by CMA was also investigated. It was found that CMA could simultaneously capture 60% SO2 and 61% HCl and reduce NO(x) concentrations by 26%, when the initial oxygen concentration in the reacting gas was 4%. During the simultaneous reduction of SO2, HCl, and NO(x), it was noted that as the initial oxygen concentration in the reacting gas increased, the efficiency of SO2 capture increased too, but the efficiency of HCl capture and the efficiency of NO(x) destruction decreased.     

Method to recover and reuse chromated copper arsenate wood preservative from spent treated wood

The volume of chromated copper arsenate (CCA) treated wood products coming out of service is expected to increase dramatically during the next decade. There is a need for an alternative waste management approach to landfilling. This paper investigates the variables affecting extraction of CCA components from wood particles and the potential to oxidize and reuse the recovered chemicals. Most of the CCA components could be extracted by 10% H2O2 at 50 degrees C in 6 h with an average extraction efficiency of 95% for Cr, 94% for Cu and 98% for As. The extract containing Cr(III), Cu(II) and As(V) could be oxidized in several stages by aqueous 2.5% w/w H2O2 in less than 2 h to a condition where it was compatible with CCA treating solutions and could be reused for treating new wood. When the recovered extract was mixed with fresh CCA solution in different ratios, the mixed CCA-C solutions had similar solution stability as freshly prepared CCA-C solution and treated wood had similar leaching properties as wood treated with fresh solution.     

Fe_2O_3和K_2CO_3对钙基添加剂脱硫脱硝的影响

在研究焦炭燃烧过程中使用钙基添加剂固硫的基础上,探讨了Fe_2O_3或K_2CO_3对CaO脱硫脱硝的影响。实验结果表明:添加剂的种类对焦炭燃烧过程中排放的SO_2和NO的浓度及总量均有一定的影响;加入Fe_2O_3或K_2CO_3替代部分CaO后,焦炭燃烧过程中排放的SO_2和NO比单独加入CaO时均有所下降;向焦炭中分别混合3.0%(w)CaO),1.5%(w)CaO+1.5%(w)Fe_2O_3,1.5%(w)CaO+1.5%(w)K_2CO_3的添加剂时,焦炭的SO_2排放总量分别降低了69.93%,75.98%,79.98%,NO排放总量分别降低了64.38%,79.73%,84.14%;加入Fe_2O_3或K_2CO_3后,钙基添加剂的表面性质发生了变化,同时增加了反应的活性中心数,因而复合添加剂能更有效地进行脱硫脱硝。     

曝气-过滤一体化装置脱氮除磷的研究

曝气-过滤一体化装置将生物反应器与过滤机理有机结合，较好地维持了反应器中的高污泥浓度，实现了水力停留时间（HRT）与污泥停留时间的分离。采用连续流间歇曝气工艺对该装置的脱氮除磷效果进行了研究。实验结果表明：在HRT为8h，运行方式为曝气2h、停曝2h的条件下，COD去除率为95．55％，NH3-N未检出，TN为84．90％，TP为93．69％，出水各项指标都达到了GB8978-1996（污水综合排放标准》一级排放标准要求。