Investigation of Biosurfactant Activity and Asphaltene Biodegradation by <Emphasis Type="Italic">Bacillus cereus</Emphasis>

In this research, a biosurfactant-producing bacterium with capability of asphaltene degradation was isolated from oil-contaminated soil samples, and identified as Bacillus cereus. This strain produced an effective biosurfactant in the presence of molasses and the surface tension was reduced to the level of 36.4 mN/m after 48 h under optimum conditions. The optimum values of carbon-to-nitrogen ratio (C:N), pH, and temperature for biosurfactant production were determined as 30:1, 7.3 and 29 °C, respectively, using response surface methodology. The maximum emulsification activity in the culture broth was 53 % after 48 h using kerosene at 25 °C. The goodness of fit of four growth kinetic models including Tessier, Contois, Logistic and Westerhoff was compared for the bacterial growth and molasses utilization of B. cereus in 5-L batch bioreactor during 120 h. Conducted kinetic study showed that biosurfactant production had a good fit with the Contois growth kinetic model (R² = 0.962) and the maximum specific growth rate (µ _max ), saturation constant (K _s ) and the yield of biomass per substrate (Y _x/s ) were determined to be 0.145 h^?1, 1.83 g/L and 0.428 g/g, respectively. The asphaltene biodegradation in flask was evaluated by FTIR analysis and quantified by a spectrophotometer. This bacterium was able to degrade up to 40 % of asphaltene as a sole carbon and energy source after 60 days at 28 °C. The resulting surface tension of 30.2 mN/m with the critical micelle concentration of 23.4 mg/L indicated good efficiency of the biosurfactant.     

Potential of biogas production from mixed leaf and food waste in anaerobic reactors

Anaerobic digestion of mixed leaf (MLW) and food wastes (FW) was used to explore the potential use of MLW as an accelerator for FW digestion in two parts for biogas production and as a waste management option in a university community. The effects of the single substrate of FW, co-digestion, ratio of MLW and FW (3:2 and 2:3) and ratio of waste feed to inoculum: F/I (0.1 and 0.4), and feeding frequency (every other day and every 2 days) were evaluated in two neutralized anaerobic reactors. The results showed that different mixture ratios with the same F/I ratio were the major factor on biogas (39.87 m³/kg VS_added) and CH₄ yield (25.99 m³/kg VS_added), including %COD removal (84.50%). Co-digestion had the same effect as F/I on biogas production. Only FW provided the lowest biogas and CH₄ yield. The use of a MLW:FW 2:3, F/I 0.4 mixture with every 2 days feeding provided higher biogas production and %COD removal than with every other day feeding. Two neutralized anaerobic reactors were suitable for digestion with a high F/I, and a wider interval feeding. This finding affirms the possibility of biogas production using MLW as the co-substrate with FW, as opposed to using FW alone.     

The mixing and segregation characteristics of rice straw in a cylindrical bubbling fluidized bed

In the present study, an experiment was performed to investigate the mixing and segregation characteristics of standard sand and rice straw particles in a cylindrical bubbling fluidized bed. The mass ratio (rice straw/standard sand = 0.5–1.25 %) of two particles and superficial gas velocity (0.13–0.18 m/s) were changed as experimental variables. The pressure drop curve and Kramer’s equation were used to determine the minimum fluidization velocity and mixing index, respectively. In all cases, the mixing index was the lowest at U/U _mf = 1.15. Based on the point of U/U _mf = 1.15, the segregation region and mixing region were observed. In the segregation region, mass ratio of 0.75 % showed the lowest mixing index. At the U/U _mf = 1.23 which was selected as the starting of fast pyrolysis considering residence time and the previous fast pyrolysis experiment, mass ratio of 1.25 % showed the highest mixing index which was 0.90.     

Kinetic Analysis of the Temperature Effect on Polyhydroxyalkanoate Production by <Emphasis Type="Italic">Haloferax mediterranei</Emphasis> in Synthetic Molasses Wastewater

Haloferax mediterranei is an extremely halophilic archaeon that is able to synthesize polyhydroxyalkanoate (PHA) in high salt environment with low sterility demand. In this study, a mathematical model was validated and calibrated for describing the kinetic behavior of H. mediterranei at 15, 20, 25, and 35 °C in synthetic molasses wastewater. Results showed that the production of PHA by H. mediterranei, ranging from 390 to 620 mg h^?1 L^?1, was strongly dependent on the temperature. The specific growth rate (µ _max), specific substrate utilization rate (q _max), and specific decay rate (k _d) of H. mediterranei increased with temperature following Arrhenius equation prediction. The estimated activation energy was 58.31, 25.59, and 22.38 kJ mol^?1 for the process of cell growth, substrate utilization, and cell decay of H. mediterranei, respectively. The high temperature triggered the increased PHA storage even without nitrogen limitation. Thus, working at high temperatures seems a good strategy for improving the PHA productivity of H. mediterranei.     

The impact of pretreatment and inoculum to substrate ratio on methane potential of organic wastes from various origins

Biochemical methane potentials (BMP) of two different substrates from macroalgae (MA) and market place wastes (MPW) were investigated using anaerobic granulated sludge from food industry with different ratios of substrate to inoculum (S/X). The substrates were used as MA only, MPW only, MA–MPW mixture, pretreated MA, and pretreated MA–MPW mixture. Research involved investigation of the effects of parameters such as temperature (35, 45, and 55 °C), substrate to inoculum ratio (S/X = 0.5, 2.0, 4.0, and 6.0 as g VS_substrate/g VS_inoculum), and the type of pretreatment (by microwave, thermal, and ultrasonic) on BMP. BMP assays were performed for all substrates. The highest cumulative biogas production (and BMP) were obtained for MA only at an S/X ratio of 4.0 g VS/g VS as 357 L_biogas/kg VS (197 L CH₄/kg VS) and 33 L_biogas/kg VS (17 L CH₄/kg VS), respectively, at 35 and 55 °C. For pretreated substrates, the highest cumulative biogas production and BMP were observed as 287 L_biogas/kg VS and 146 L CH₄/kg VS using pretreated macroalgae at 35 °C. Results suggested that MA only and MA–MPW mixtures are suitable substrates for biogas production. It is also concluded that any type of pretreatment has adverse effects on biogas and methane productions.     

Optimization of mixing ratio of ammoniated rice straw and food waste co-digestion and impact of trace element supplementation on biogas production

The anaerobic co-digestion of biomass waste, a promising process of reusing resources, is capable of improving methane production. However, the characteristics and composition of fermenting raw material negatively influence the efficiency of methane production. Optimization experiments were systematically performed in this study through anaerobic co-digestion with urea-ammoniated rice straw (UARS) and food waste (FW) as co-substrates. Anaerobic co-digestion of UARS and FW in biogas production under mesophilic conditions (35 °C) was investigated in a 1 L enclosed triangular flask with a total organic load of 6 g volatile solids (VS)/L. The optimal mixing ratio of UARS to FW was close to 1:3, and the methane yield increasing by 8.83% compared with the sole substrate. Furthermore, based on the optimization ratio, supplementation of cobalt (Co) and nickel (Ni) on co-digestion were significantly superior to that of a single element. Additionally, kinetic analysis indicated that trace element remarkably facilitated the reaction rate of co-digestion. Noteworthy, the addition of Co, Ni, and the combination of Co and Ni achieved very significant (p < 0.01) improvement of 6.45, 8.36, and 13.65%. Meanwhile, Ni was substantially promoted the removal rate of VS, enhanced the operational stability of co-digestion and increased the methane content significantly.     

Enhanced bioleaching efficiency of copper from waste printed circuit boards (PCBs) by dissolved oxygen-shifted strategy in <Emphasis Type="Italic">Acidithiobacillus ferrooxidans</Emphasis>

Acidithiobacillus ferrooxidans, as chemolithotrophic aerobic bacterium, can obtain energy by oxidation of ferrous ions (Fe²⁺) to ferric ions (Fe³⁺) and use molecular oxygen (O₂) as terminal electron acceptor. In this study, the effects of dissolved oxygen (DO) levels in culture medium on cell growth and copper extraction from waste printed circuit boards (PCBs) were investigated in A. ferrooxidans. The whole culture period was divided into two stages of cell growth and copper extraction. At the former stage, relatively lower DO level was adopted to satisfy bacterial growth while avoiding excessive Fe²⁺ oxidation. At the later stage, higher DO was used to promote copper extraction. Moreover, shift time of DO from lower to higher level was determined via simulating Gauss function. By controlling DO at 10 % for initial 64 h and switching to 20 % afterwards and with 18 g/l PCBs addition at 64 h, final copper recovery reached 94.1 %, increased by 37.6 and 48.3 % compared to constant DO of 10 and 20 % operations. More importantly, copper leaching periods were shortened from 108 to 60 h. It was suggested that application of DO-shifted strategy to enhancing copper extraction from PCBs with reduced leaching periods is being feasible.     

BMP estimation of landfilled municipal solid waste by multivariate statistical methods using specific waste parameters: case study of a sanitary landfill in Turkey

The main objective of this study was to determine whether methane potential of waste could be estimated more easily by a limited number of waste characterization variables. 36 samples were collected from 12 locations and 3 waste depths in order to represent almost all waste ages at the landfill. Actual remaining methane potential of all samples was determined by the biochemical methane potential (BMP) tests. The cumulative methane production of closed landfill (cLF) samples reached 75–125 mL at the end of experiment duration, while the samples from active landfill (aLF) produced in average 216–266 mL methane. The average experimental k and L ₀ values of cLF and aLF were determined by non-linear regression using BMP data with first-order kinetic equation as 0.0269 day^?1–30.38 mL/g dry MSW and 0.0125 day^?1–102.1 mL/g dry MSW, respectively. The principal component analysis (PCA) was applied to analyze the results for cLF and aLF along with BMP results. Three PCs for the data set were extracted explaining 72.34 % variability. The best MLR model for BMP prediction was determined for seven variables (pH–Cl–TKN–NH4–TOC–LOI–Ca). R ² and Adj. R ² values of this best model were determined as 80.4 and 75.3 %, respectively.     

Assessment of compost dosage in farmland through ecotoxicological tests

A research project was carried out to evaluate ecotoxicological effects of mature compost addition to agricultural soil, using a battery of ecotoxicological tests. The following species were selected: plant of Lepidium sativum, earthworm Eisenia foetida, aquatic crustacean Daphnia magna and bacteria Vibrio fischeri. The tests were classified as “direct tests” using solid compost samples and “indirect tests” using compost leaching test eluate. The direct bioassays were performed using compost added to artificial soil in concentrations ranging from 2.5 to 100 % (w/w); the indirect ones considered compost eluate, added to a standard solution in the same concentrations used in the direct tests. Both tests aimed at obtaining the ecotoxicological parameters (LC₅₀ and EC₅₀). These values were then utilized to implement the Species Sensitivity Distribution (SSD) analysis and extrapolate the Hazard Concentration (HC), a useful threshold to preserve the biodiversity of agricultural ecosystems. Results indicated an increase in compost toxicity with greater compost concentrations; in particular, for direct tests compost dosage below 10 % showed low toxicity, while for indirect ones the toxicity was higher. Furthermore, SSD analysis showed a Hazardous Concentration (HC₅) for direct bioassays of 3.5 % and for indirect of 14 %.     

Adsorption of Crystal Violet Dye from Aqueous Solution by Poly(Acrylamide-<Emphasis Type="Italic">co</Emphasis>-Maleic Acid)/Montmorillonite Nanocomposite

Poly(acrylamide-co-maleic acid)/montmorillonite nanocomposites, were synthesized via in situ polymerization with different maleic acid and MMT content. The capability of the hydrogel for adsorption of crystal violet (CV) was investigated in aqueous solutions at different pH values and temperatures. The pseudo-second-order kinetics model could fit successfully the adsorption kinetic data. The effects of maleic acid to acrylamide molar ratio (MA_R), weight percent of MMT (MMT%), the pH of medium and the solution temperature (T) on the CV adsorption capacity (q _e ) of adsorbents were studied by Taguchi experimental design approach. The results indicated that increasing the MMT% leads to a greater q _e . The q _e value of adsorbents increased also with increasing both MA_R and pH, while reduced when the temperature of medium increased. The relatively optimum conditions to achieve a maximum CV adsorption capacity for P(AAm/MA)/MMT adsorbents were found as: 0.06 for MA_R and 5 % of MMT%, medium pH = 7 and T = 20 °C.     

Sulfated Polysaccharides from Tunisian Fish Skins: Antioxidant,DNA Damage Protective Effect and Antihypertensive Activities

Sulfated polysaccharides were isolated from two Tunisian fish skins grey triggerfish (Balistes capriscus) (GTSP) and smooth hound (Mustelus mustelus) (SHSP). Their chemical and physical characteristics were investigated. The Analysis of surface morphology by scanning electron microscopy of both sulfated polysaccharides displayed the same shape with netted structure. The antioxidant activities of GTSP and SHSP were evaluated using various in vitro antioxidant assays: 1,1-diphenyl-2-picrylhydrazyl (DPPH) radical-scavenging activity, reducing power, β-carotene bleaching inhibition assay (IC_{50 GTSP} = 0.5 mg mL^?1 and IC_{50 SHSP} = 0.6 mg mL^?1) and DNA nicking assay. Both sulfated polysaccharides exhibited good antioxidant activities. The sulfated polysaccharides showed strong angiotensin I-converting enzyme inhibitory activities (IC_{50 GTSP} = 0.16 mg mL^?1 and IC_{50 SHSP} = 0.18 mg mL^?1). These results revealed that GTSP and SHSP exhibited significant antihypertensive activities. Overall, the results indicated that grey triggerfish and smooth hound skins can be used to generate high value-added products, thus offering a valuable source of bioactive sulfated polysaccharides for application in wide range of biotechnological applications.     

Comparison of three ornamental plants for phytoextraction potential of chromium removal from tannery sludge

Based on pre-experimentation, three ornamental plants, Mirabilis jalapa, Impatiens Balsamin (I. Balsamin) and Tagetes erecta L., were selected as target plants to study the phytoextraction of chromium (Cr) in tannery sludge irrigated with four treatments according to Cr concentration gradient [Control (CK); 20.50 × 10³ mg kg^?1 (T1); 51.25 × 10³ mg kg^?1 (T2); 102.50 × 10³ mg kg^?1 (T3)]. Results of pot experiments showed that the biomass of Mirabilis jalapa and Tagetes erecta L. had no significant differences among the four treatments, while I. Balsamin showed a decline trend in the biomass with the increase of Cr concentration, probably due to some extent to the poisoning effect of Cr under treatment T2 or T3. Mirabilis jalapa accumulated Cr concentration, with 408.97, 124.97, 630.16 and 57.30 mg kg^?1 in its roots, stems, leaves and inflorescence, respectively. The translocation factor and the bioaccumulation coefficient of Mirabilis jalapa are each greater than 1, indicating that Mirabilis jalapa has the strong ability to tolerate and enrich Cr by biological processes. Comparing accumulation properties of the three ornamental plants, in the amount and allocation, Mirabilis jalapa showed the highest phytoextraction efficiency and could grow well at the high Cr concentration. Our experiments suggest that Mirabilis jalapa is the expected flower species for Cr removal from tannery sludge.     

Increased 3HV Concentration in the Bacterial Production of 3-Hydroxybutyrate (3HB) and 3-Hydroxyvalerate (3HV) Copolymer with Acid-Digested Rice Straw Waste

Bacterial synthesis of 3-hydroxybutyrate (3HB) and 3-hydroxyvalerate (3HV) copolymer [P(3HB-co-3HV)] using the hydrolysate of rice straw waste as a carbon source was affected by the composition of the hydrolysate, which depends highly on the rice straw pretreatment condition. Acid digestion with 2 % sulfuric acid generated larger production of P(3HB-co-3HV) than 6 % sulfuric acid, but 3HV concentration in the copolymer produced with 2 % acid hydrolysate was only 8.8 % compared to 18.1 % with 6 % acid hydrolysate. To obtain a higher 3HV mole fraction for enhanced flexibility of the copolymer, an additional heating was conducted with the 2 % acid hydrolysate after removal of residual rice straw. As the additional heating time increased a higher concentration of levulinic acid was generated, and consequently, the mole fraction of 3HV in P(3HB-co-3HV) increased. Among the conditions tested (i.e., 20-, 40-, 60-min), 60-min additional heating following 2 % sulfuric acid digestion achieved the highest 3HV mole fraction of 22.9 %. However, a longer heating time decreased the P(3HB-co-3HV) productivity, probably due to the increased intermediates concentrations acting as inhibitors in the hydrolysates. Therefore, the use of additional heating needs to consider both the increase in the 3HV mole fraction and the decrease in the P(3HB-co-3HV) productivity.     

Itaconic Acid Grafted Starch Hydrogels as Metal Remover: Capacity,Selectivity and Adsorption Kinetics

Hydrogels were synthesized by free radical graft copolymerization of itaconic acid (IA) onto corn starch (S-g-IA). For this purpose, potassium permanganate (KMnO₄)-sodium bisulfite (NaHSO₃) was used as redox initiation system. The formation of grafted starches was confirmed by Fourier transform infrared spectroscopy, wide angle X-ray scattering, thermogravimetric analysis and scanning electron microscopy. The effect of monomer concentration, neutralization, addition of crosslinking agent, N,N-bismetilenacrilamide (MBAm), and initiator concentration on grafting efficiency and adsorption capacity of the starch hydrogels was investigated. It was demonstrated that the introduction of carboxyl and carbonyl groups promoted starch hydration and swelling. Grafting degree increased with the decrease of monomer concentration, increase of initiator concentration, grade of neutralization and the addition of MBAm without neutralization. Remarkably the resulting materials exhibited water absorption capacities between 258 and 1878% and the ability to adsorb metal ions. It was experimentally confirmed the metal uptake, obtaining the higher adsorption capacity (q _e  = 35 mg/g) for the product prepared with the pre-oxidation and lower initiator concentration. The removal capacity order was Pb²⁺>Ni²⁺>Zn²⁺>Cd²⁺. Moreover, the experimental kinetic and the equilibrium adsorption data for Ni²⁺ and Pb²⁺ were best fitted to the pseudo-second order and Freundlich isotherm models, respectively. This work describes for the first time the preparation of metal removal hydrogels based on starch and itaconic acid using the pair redox system KMnO₄/NaHSO₃, which avoids the starch hydrolysis and allows itaconic acid grafting incorporation without the requirement of more reactive comonomers.     

Enzyme-Assisted Extraction and Pb<Superscript>2+</Superscript> Biosorption of Polysaccharide from <Emphasis Type="Italic">Cordyceps militaris</Emphasis>

The enzyme assisted extraction conditions of polysaccharide from Cordyceps militaris mycelia were firstly investigated by kinetics analysis and the optimal operating was found to be: extraction temperature 40 °C; solid-solvent ratio 1:20; extraction pH 4.0; cellulase concentration 2.0%. The polysaccharide extraction yield was 5.99% under these optimized conditions. Furthermore, a fundamental investigation of the biosorption of Pb²⁺ from aqueous solution by the C. militaris polysaccharide was performed under batch conditions. The suitable pH (5.0), polysaccharide concentration (0.20 g L^?1), initial Pb²⁺ concentration (300 mg L^?1) and contact time (40 min) were outlined to enhance Pb²⁺ biosorption from aqueous medium. The Langmuir isotherm model and pseudo first order kinetic model fitted well to the data of Pb²⁺ biosorption, suggesting the biosorption of Pb²⁺ onto C. militaris polysaccharide was monolayer biosorption and physical adsorption might be the rate-limiting step that controlled the adsorption process. FTIR analysis showed that the main functional groups of C. militaris polysaccharide involved in adsorption process were carbonyl, carboxyl, and hydroxyl groups.     

Evaluation of batch anaerobic co-digestion of palm pressed fiber and cattle manure under mesophilic conditions

Palm pressed fiber (PPF) and cattle manure (CM) are the waste which can be managed properly by anaerobic co-digestion. The biogas production in co-digested PPF and CM at three volatile solids (VS) ratios of 3:1, 1:1, and 1:3 was investigated in a series of batch experiments at an organic loading rate of 30.0 g VS/L under mesophilic (37 ± 1 °C) conditions. The highest daily biogas yield of PPF and CM only, was 90.0 mL/g VS_added at day 12 and 23.4 mL/g VS_added at day 7. For co-digestion of PPF/CM at mixing ratios of 3:1, 1:1 and 1:3, there were 93.6 mL/g VS_added at day 11, 86.8 and 26.4 mL/g VS_added at day 8. VS removal rate for PPF, CM, and co-digestion at mixing ratio of 3:1, 1:1, and 1:3 were 91.1%, 86.0% and 71.0%, respectively. The anaerobic digestion of PPF and CM and their co-digestion systems were stable in operation with low range of volatile fatty acids (VFA)/TIC (total inorganic carbon) of (0.035–0.091). The main volatile fatty acids were propionic, and iso-butyric acids for PPF, iso-butyric and n-butyric acids for CM. The VFAs and ammonium inhibition were not occurred. The modified Gompertz model can be used to perform a better prediction with a lower difference between the measured and predicted biogas yields. A VS ratio of 3:1 is recommended for practice.     

Water Absorption Kinetics and Hygrothermal Aging of Poly(lactic acid) Containing Halloysite Nanoclay and Maleated Rubber

Poly(lactic acid)/halloysite nanoclay composites (PLA/HNC) containing maleic anhydride grafted styrene-ethylene/butylene-styrene (SEBS-g-MAH) were produced using melt compounding followed by compression molding. The effects of hygrothermal aging on the thermal properties and functional groups changes of the HNC reinforced PLA (with and without SEBS-g-MAH) at three different temperatures (i.e., 30, 40 and 50 °C) were analyzed using differential scanning calorimetry and Fourier transform infrared spectroscopy techniques. The diffusion coefficient (D) of PLA was decreased by the incorporation of HNC and SEBS-g-MAH. The activation energy of water diffusion (E _a ) of PLA/HNC/SEBS-g-MAH nanocomposites was higher than that of pure PLA. The glass transition temperature (T _g ), cold-crystallization temperature (T _cc ) and melting temperature (T _m ) of the PLA sample were shifted to lower temperature and the effect was more pronounced at 50 °C. The carbonyl index values of all PLA samples increased after immersed in 40 and 50 °C, which is due to the formation of higher amount of carboxyl groups during the hydrolysis process.     

Synthesis and Properties of Polyesters from Waste Grapeseed Oil: Comparison with Soybean and Rapeseed Oils

The aim of this study was to investigate the application of grapeseed oil, a waste product from the wine industry, as a renewable feedstock to make polyesters and to compare the properties of these materials with those derived from soybean and rapeseed oils. All three oils were epoxidized to give renewable epoxy monomers containing between 3.8 and 4.7 epoxides per molecule. Polymerisation was achieved with cyclic anhydrides catalysed by 4-methyl imidazole at 170 and 210 °C. Polymers produced from methyl tetrahydrophthalic anhydride (Aradur917^®) had greater tensile strength and Young’s Modulus (tensile strength = 12.8 MPa, Young’s Modulus = 1005 MPa for grapeseed) than methyl nadic anhydride (MNA) derived materials (5.6 and 468 MPa for grapeseed) due to increased volume of MNA decreasing crosslink density. Soybean and grapeseed oils produced materials with higher tensile strength (5.6–29.3 MPa) than rapeseed derived polyesters (2.5–3.9 MPa) due to a higher epoxide functionality increasing crosslinking. T _g’s of the polyesters ranged from ?36 to 62 °C and mirrored the trend in epoxide functionality with grapeseed producing higher T _g polymers (?17 to 17 °C) than soybean (?25 to 6 °C) and rapeseed (?36 to ?27 °C). Grapeseed oil showed similar properties to soybean oil in terms of T _g, thermal degradation and Young’s Modulus but produced polymers of lower tensile strength. Therefore grapeseed oil would only be a viable substitute for soybean for low stress applications or where thermal properties are more important.     

Application of ameliorated wood pulp to recover Cd(II), Pb(II), and Ni(II) from e-waste

In this study, dl-malic acid and hydrogen peroxide were used as leaching agents to remove metals from e-waste (printed-circuit boards) and itaconic acid-grafted poly(vinyl alcohol)-encapsulated wood pulp (IA-g-PVA-en-WP) to uptake metals from leachate with high proficiency [11.63 mg g^?1; 93.03 % for Cd(II), 11.90 mg g^?1; 95.18 % for Pb(II), and 12.14 mg g^?1; 97.08 % for Ni(II)]. Metals were recovered from the loaded biosorbent by desorption studies. The standard analytical techniques, such as elemental analysis, Fourier-transform-infrared spectroscopy, scanning electron microscopy, atomic force microscopy, and thermogravimetric analysis, were used to characterize the recovering agent (biosorbent). At equilibrium, the metal uptake data were fitted to Langmuir and D–R isotherms (R ² > 0.99) significantly, revealing, the homogeneous distribution of active sites on biosorbent’s backbone. The possible mechanism appeared to be ion exchanges of metal ions with H⁺ together with binding over functionalities (COO^?). Dimensionless equilibrium parameter (R _L) showed the favourability of metal uptake at lower concentration, while mean adsorption energy (E) certified the physical binding of metal on functionalities which was further confirmed by sticking probability and activation energy parameters. Reusability studies were also conducted to state the performance of biosorbent.     

In Vivo and In Vitro Degradation Studies for Poly(3-hydroxybutyrate-<Emphasis Type="Italic">co</Emphasis>-3-hydroxyhexanoate) Biopolymer

Studies have shown that the copolymer poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) [P(HB-co-HHx)] possesses favorable mechanical properties for use in medical supplies and products (e.g., sutures, scaffolds, bone plates). One of the major under-addressed issues associated with the use of biodegradable, bio-based PHA polymers in resorbable medical products is the correlation between the mechanical properties and the in vivo material degradation over time. In this study, P(HB-co-17 mol% HHx) matrices were mechanically tested after either incubation in cultures of human embryonic kidney cells (HEK) for in vitro degradation studies for up to 4 weeks, or inserted into Danio rerio (zebrafish) tissues for in vivo degradation studies for up to 7 weeks. The mechanical properties and scanning electron microscopy (SEM) images of the degraded materials were examined and later correlated to understand the degradation phenomenon. Our results show that Young’s modulus of P(HB-co-17 mol%HHx) during in vitro studies decreased from 3.26 to 2.42 GPa within 4 weeks, and in vivo breakdown resulted in a significant decrease in Young’s modulus with a decrease from 3.26 to 0.51 GPa and a mass loss of 59 % within 7 weeks. SEM images showed the development of pores and cracks on the surface of the material over time. Plasticization and recrystallization were observed and likely play a role in the alteration of mechanical properties.