用沸石吸附稀土冶炼氯铵废水中的氨氮

用天然沸石对稀土冶炼氯铵废水中的氨氮进行吸附实验。通过实验得到的最佳工艺条件为：废水pH7—8、沸石粒径0．5—1．0mm、沸石投加量60g；先以300r／min搅拌1min，再以60r／min搅拌30min，沉降30min。稀土冶炼氯铵废水经沸石吸附处理后，废水中的氨氮质量浓度由13013mg／L降至6168mg／L，氨氮去除率达52．6％。     

沸石-壳聚糖吸附剂吸附废水中的Ni2+

采用沸石-壳聚糖吸附剂吸附废水中的Ni2＋。将粒径为180μm的天然沸石与脱乙酰度90％的壳聚糖混合，制成沸石一壳聚糖吸附剂。考察了沸石一壳聚糖吸附剂对模拟含镍废水中的Ni2＋静态吸附效果的影响因素。正交实验结果表明，在壳聚糖与天然沸石质量比为0．05、吸附剂加入量为14g/L、Ni2＋初始质量浓度为40mg／L、模拟含镍废水pH为6—7、吸附时间为40min的条件下，模拟含镍废水中Ni2＋去除率大于96％。对实际电镀含镍废水的动态吸附实验结果表明，NP的质量浓度由38．0mg／L减少到0．8mg／L，小于GB8978-96《污水综合排放标准》规定值（1．0mg／L）。     

生物质吸附剂处理活性艳红X-3B废水

采用城市污水处理厂二沉池的剩余活性污泥为原料，以浓度为3mol／L的ZnCl2溶液浸泡污泥，采用水蒸气为活化气和保护气，在600℃下活化污泥3h，制备出性能良好的生物质吸附剂，其碘吸附值为388．95mg／g，比表面积为447．79m^2／g，平均孔径为4．39nm，孔体积为0．31cm^3／g，微孔体积为0．09cm^3/g。实验结果表明，用该生物质吸附剂处理活性艳红X-3B废水，在废水（10mL）中活性艳红X-3B质量浓度为300mg／L、生物质吸附剂加入量为0．20g、吸附时间为30min的条件下，废水脱色率可达99．7％。活性艳红X-3B在生物质吸附剂上的吸附行为遵循Lagergren二级动力学规律，同时也可用一级吸附动力学方程描述。     

膨胀石墨对直接染料废水吸附脱色研究

以鳞片石墨、乙酸酐、浓硫酸、重铬酸钾为原料制备了膨胀体积为350mL／g的膨胀石墨。以膨胀石墨为吸附剂，对直接大红4B、甲基橙染料废水进行了吸附脱色研究，探讨了影响吸附的因素。实验结果表明：直接大红4B（质量浓度300mg／L）、甲基橙（质量浓度200mg／L）的吸附平衡时间分别为6h和5h；在相同质量浓度（200mg／L）下，pH对两种染料废水的脱色率影响不大，膨胀石墨对直接大红4B废水的脱色率在93％以上，对甲基橙废水的脱色率最高只有70．4％；直接大红4B废水的脱色率随温度的升高而增加，甲基橙废水的脱色率随温度的升高而减小，但吸附量受温度的影响不大，两种染料的吸附符合Langumuir吸附等温式。     

核桃壳吸附剂对水中Pb2+的吸附

采用自制核桃壳吸附剂，利用静态吸附法，处理模拟含Pb²⁺废水。实验结果表明：当初始Pb²⁺的质量浓度20.00 mg/L、初始废水pH=5.5、吸附剂加入量12 g/L、吸附剂粒径1.60~2.50 mm、吸附时间120 min时，核桃壳吸附剂对Pb²⁺的去除率为91.7%；吸附剂对Pb²⁺的吸附行为满足拟二级吸附动力学方程，吸附等温线满足Langmuir等温方程，饱和吸附量达到3.903 mg/g；吸附饱和的吸附剂可用浓度 0.1 mol/L的硝酸解吸，经解吸后的吸附剂可重复利用3次。     

海藻酸钠-聚乙烯醇-聚乙二醇复合膜的制备及其对Cu2+的吸附

采用聚乙烯醇（PVA）、聚乙二醇（PEG）对海藻酸钠（SA）进行改性，制备了一种新型高效SA-PVA-PEG复合膜。研究了该复合膜对Cu²⁺的吸附效果。用IR和SEM等手段对复合膜进行了表征。表征结果显示，复合膜内部存在孔状结构，有利于吸附Cu²⁺。实验结果表明：在初始Cu²⁺质量浓度50 mg/L、复合膜加入量1 g/L、废水pH=5、吸附温度30 ℃、吸附时间60 min的最佳条件下，吸附率最高可达90.1%，吸附量达25.3 mg/g；复合膜吸附Cu²⁺的动力学过程可用二级动力学方程和Elovice方程进行拟合，吸附过程符合Langmuir单层吸附理论。采用浓度为1 mol/L的HCl溶液对吸附后的复合膜进行解吸，当解吸时间为2 min时，解吸率可达80.0%。     

焦粉活性炭的制备及其应用

用废弃焦粉制备焦粉活性炭，通过正交实验考察了各种因素对焦粉活性炭性能的影响。实验结果表明：在活化时间80min、活化温度900℃、碱炭比（氢氧化钾与废弃焦粉的质量比）4、废弃焦粉粒径小于0．05mm的最佳条件下，制备的焦粉活性炭的亚甲基蓝吸附值为304．8mg／g，产率为35．6％；废弃焦粉的活化是活化剂刻蚀其颗粒形成丰富孔结构的氧化还原反应过程；用最佳条件下制备的焦粉活性炭处理质量浓度为60mg／t．的模拟含Cr^6＋废水，在废水pH为3—4、焦粉活性炭加入量为4g/L、吸附时间为50min的条件下，Cr^6＋去除率达93．2％。     

苯基周位酸生产废水处理试验研究

采用CHA－111大孔吸附树脂对苯基周位酸生产过程排放的汽提苯胺盐析废水和苯基周位酸酸析母液进行处理试验,效果良好。汽提苯胺盐析废水苯胺质量浓度＞1600mg／L,经树脂吸附处理后苯胺质量浓度＜2mg／L,苯胺去除率＞99．9％,COD去除率＞97％,树脂工作吸附量达120g／L,脱附率＞98％;苯基周位酸酸析母液经树脂吸附、混凝沉淀处理后,苯基周位酸质量浓度＜190mg／L,苯基周位酸去除率为94．8％,COD去除率为94．3％,氨基值去除率为80％,脱附率＞99％。     

海藻酸钠-聚乙烯醇-聚乙二醇复合膜的制备及其对Cu~(2+)的吸附

采用聚乙烯醇(PVA)、聚乙二醇(PEG)对海藻酸钠(SA)进行改性,制备了一种新型高效SA-PVA-PEG复合膜。研究了该复合膜对Cu2+的吸附效果。用IR和SEM等手段对复合膜进行了表征。表征结果显示,复合膜内部存在孔状结构,有利于吸附Cu2+。实验结果表明:在初始Cu2+质量浓度50 mg/L、复合膜加入量1 g/L、废水pH=5、吸附温度30℃、吸附时间60 min的最佳条件下,吸附率最高可达90.1%,吸附量达25.3 mg/g;复合膜吸附Cu2+的动力学过程可用二级动力学方程和Elovice方程进行拟合,吸附过程符合Langmuir单层吸附理论。采用浓度为1 mol/L的HCl溶液对吸附后的复合膜进行解吸,当解吸时间为2 min时,解吸率可达80.0%。     

超声辐射法降解废水中的二甲苯、苯酚和丙烯腈

采用频率为20kHz的超声波处理二甲苯、丙稀腈、苯酚溶液。实验结果表明，在二甲苯初始质量浓度为27．6mg／L、H2O2质量浓度为1．68g／L、溶液温度为25℃、声强为141．32W／cm^2、辐射全程时间为60min的条件下，二甲苯降解率可达99．20％；在丙烯腈初始质量浓度为100．0mg／L、通氧量为15mL／rain、溶液温度为28℃、声强为141．32W／cm^2、辐射全程时间为30rain的条件下，丙烯腈降解率可达98．20％；在苯酚初始质量浓度为20．0mg／L、H202质量浓度为1．50g／L、FeSO4质量浓度为0．22g／L、溶液温度为28℃、声强为48．92W／cm^2、辐射全程时间为40rain的条件下，苯酚降解率可达99．81％。     

Distribution of Cd,Ck, Pb and Zn in Soil and Vegetation Compartments in Stands of Five Boreal Tree Species in N.E. Sweden

Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.     

Programs assessing implementation and effectiveness of state forest practice rules and BMPs in the West

The major forest nonpoint source control programs in the West are largely regulatory, either under forest practices acts (California, Idaho, New Mexico, Nevada, Oregon, and Washington) or a streamside management act (Montana). These programs and the specific rules they enforce continue to undergo intensive scrutiny. Still, the questions are the same for these regulatory programs as for states that base nonpoint source control on voluntary BMPs (Arizona, Colorado, Utah, Wyoming). Are the rules or BMPs being applied, and are they effective in reducing nonpoint source pollution to levels that protect beneficial uses of water? The level of debate about forestry in the West has resulted in detailed monitoring and research to answer these questions. In the past, state agencies have assumed levels of BMP compliance based on the percent of operations without enforcement actions. These estimates are being replaced by statistically valid and reproducible monitoring of forest practices rules and BMP compliance levels. BMP effectiveness is being assessed using both qualitative and quantitative methods. This can involve field assessments, process-based research, and control watershed studies. Some trend monitoring is also beginning. With the regional implementation rate for forestry BMPs at about 94% and rising, it is likely that effectiveness testing will continue to be a priority and consume the majority of assessment resources for this region.     

Hysteresis in Reversal of Central European Mountain Lakes from Atmospheric Acidification

Extremely high emissions of S and N compounds in Central Europe (both 280 mmol m^-2 yr^-1) declined by 70and 35%, respectively, during the last decade. Decreaseddeposition rates of SO₄ ^-2, NO₃ ^-, and NH₄ ⁺ in the region paralleled emission declines. The reduction in atmospheric inputs of S and N to mountain ecosystemshas resulted in a pronounced reversal of acidification in the Tatra Mountains and Bohemian Forest lakes. Between the 1987–1990and 1997–1999 periods, concentrations of SO₄ ^-2 and NO₃ ^- decreased (average ± standard deviation) by 22±7 and 12±7 mol L^-1, respectively, in theTatra Mountains, and by 19±7 and 15±10 mol L^-1, respectively, in the Bohemian Forest. Their decrease was compensated in part (1) by a decrease in Ca²⁺ + Mg²⁺ (17±7 mol L^-1) and H⁺ (4±6 mol L^-1), and an increase in HCO₃ ^-(10±10 mol L^-1) in the Tatra Mountains lakes, and (2) by a decrease in Al (7±4 mol L^-1), Ca²⁺ + Mg²⁺ (9±6 mol L^-1), and H⁺ (6±5 mol L^-1), in Bohemian Forest lakes. Despite the rapid decline in lake water concentrations of SO₄ ^-2 and NO₃ ^- in response to reduced S and N emissions, their present concentrations in some lakes are higher than predictionsbased on observed concentrations at comparable emission rates during development of acidification. This hysteresis in chemical reversal from acidification has delayed biological recovery of the lakes. The only unequivocal sign of biological recovery hasbeen observed in erné Lake (Bohemian Forest) where a cladoceran species Ceriodaphnia quadrangular has recentlyreached its pre-acidification abundance.     

Reconstruction of Long-Term Changes in Lake water Chemistry,Zooplankton and Benthos of a Small,Acidified High-Mountain Lake: Magic Modelling and Palaeolimnogical Analysis

Starolesnianske pleso is a small and shallow acid lake in the High Tatra Mountains, situated at 2000 m above sea level, on granitic bedrock, with sparse and thin soil cover. When detailed measurements began in the 1980s Starolesnianske pleso had pH below 5 and only one species of cladoceran zooplankton, the ubiquitous Chydorus sphaericusPalaeolimnological investigations show changes in cladoceran zooplankton and chironomid zoobenthic assemblages since about 1920 and a major change in 1970–1980. The dynamic acidification model MAGIC was used to reconstruct changes in water chemistry over the past 150 years. The results from MAGIC agree well with the sediment record; pH levels gradually decreased from 6.5 in the mid-1800s to about 5.6 in 1920 (first response in biota) to below 5.0 by 1970, and concentrations of inorganic aluminium rose dramatically beginning about 1960. In the 1990s the lake water chemistry showed clear signs of reversal in acidification brought about by a major decline in S deposition.     

Heavy Metals Removal by Biosorption and Flotation

The removal of a mixture of heavy (toxic) metal cations (copper, nickeland zinc) from liquid effluents was investigated in this study at pilotscale, using counter-current contact mode. The innovative processinvolved the abstraction of metal ions onto fungal biosorbents, followedby the application of flotation for the subsequent solid/liquid separationof biomass particles. The ability of microorganisms to remove metal ionsfrom aqueous solutions is a well-known phenomenon. Nevertheless,engineering considerations are very important in decisions, concerningthe commercial future of biosorption and practical solutions are neededfor certain problems, such as the efficient post-separation ofmetal-loaded biomass. The two processes (flotation and biosorption) caneffectively operate in combination, in what it was termed biosorptiveflotation process. The sorbents may be recycled, after appropriate elutionof metals, as well as the treated (clean) water.     

Starch-plastic materials—Preparation,physical properties,and biodegradability (a review of recent USDA research)

Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

Bioassessment of silvicultural impacts in streams and wetlands of the Eastern United States

Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.     

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.     

Selection of Autochthonous Plant Species from SE Spain for Soil Lead Phytoremediation Purposes

Mining activity in SE of Spain, in the west Mediterranean coast, originated more than two millenniums ago. It has generated huge areas affected by heavy metals contamination, especially of lead, which is possibly one of the most important. Investigations related to the selection of autochthonous plant taxa from a typical Spanish Mediterranean area, useful for phytoextraction and phytostabilization purposes in these polluted areas are shown. Under these edaphoclimatic conditions 12 interesting species were considered, from them six taxa were chosen for further studies. Some plant species have been proposed either for phytoextraction or phytostabilization purposes. Recommendations for further research have been discussed.     

Concentrations and Pools of Heavy Metals in Urban Soils in Stockholm,Sweden

The concentrations of heavy metals (Cd, Cr, Cu, Hg, Ni, Pb andZn) and arsenic (As) were surveyed and the metal pools estimatedin soils in Stockholm Municipality. The sampling sites were distributed all over the entire municipality with a higher sampling density in the city centre. Soils were sampled to a maximum depth of 25 to 60 cm. Soil texture, total-C content, electrical conductivity and pH were analysed. Heavy metal concentrations were determined after wet digestion with boiling7 M HNO₃.The results showed a wide range in heavy metal concentrations, as well as in other soil properties. The city centre soils constituted a rather homogeneous group whereas outside this areano geographical zones could be distinguished. These soils were grouped based on present land use, i.e. undisturbed soils, public parks, wasteland (mainly former industrial areas), and roadside soils. The city centre and wasteland soils generally hadenhanced heavy metal concentrations to at least 30 cm depth compared to park soils outside the city centre and rural (arable)soils in the region, which were used to estimate background levels. For example, the mean Hg concentration was 0.9 (max 3.3)mg kg^-1 soil at 0–5 cm and 1.0 (max 2.9) at 30 cm depth in the city centre soils, while the background level was 0,04 mg kg^-1. Corresponding values for Pb were 104 (max 444) and135 (max 339) mg kg^-1, at 0–5 and 30 cm, respectively, while the background level was 17 mg kg^-1.The average soil pools (0–30 cm depth) of Cu, Pb and Zn were 21,38 and 58 g m^-2 respectively, which for Pb was 3–4 timeshigher and for Cu and Zn 1.5–2 times higher than the backgroundlevel. The total amount of accumulated metals (down to 30 cm)in the city centre soils (4.5^*10 ⁶ m² public gardens and green areas) was estimated at 80, 1.1, 120 and 40 t for Cu, Hg, Pb and Zn, respectively. The study showed (1) thatfrom a metal contamination point of view, more homogeneous soilgroups were obtained based on present land use than on geographicdistance to the city centre, (2) the importance of establishing a background level in order to quantify the degree of contamination, and (3) soil samples has to be taken below the surface layer (and deeper than 30 cm) in order to quantify theaccumulated metal pools in urban soils.