300MW锅炉低NOx燃烧系统改造效果分析

针对日益严重的环境污染、锅炉热效率低等问题，阐述了燃煤锅炉炉内空间分级燃烧技术、煤粉浓淡高效分离技术改造项目和特点，提出了对燃烧器系统、一次风管道、二次风系统和空预器系统等系统进行具体的低氮改造措施。分析了300 MW燃煤锅炉低氮改造后的热经济性和安全性。经试验验证，1号锅炉低氮改造后，锅炉NOx 排放量大幅减少，排放浓度降到了280 mg／m3。     

锅炉低NOx排放改造及试验结果分析

介绍了某电厂利用空气分级燃烧技术对420t／h锅炉燃烧器进行的低NOx排放改造情况，对锅炉改造前、后的NOx排放浓度进行了对比分析。结果表明，对锅炉实施低NOx改造后，NOx排放浓度明显下降，但锅炉热效率亦有所降低。     

大型燃用贫煤和烟煤锅炉NOx排放特性的研究

针对两台分别燃用贫煤和烟煤的３００ＭＷ锅炉（均采用ＷＲ型燃烧器）ＮＯｘ排放特性,分析辽两台锅炉在满负荷和低负荷时ＮＯｘ排放量的差别,并指出了燃用贫煤的锅炉比燃用烟煤的锅炉ＮＯｘ排放量高的原因。     

我国中小型锅炉的NOx排放特征与管理对策

对我国中小型燃煤、燃油、燃气锅炉的NOx排放监测数据进行了统计分析,探讨了NOx的排放特征与管理控制现状.研究结果表明:燃煤锅炉中NOx排放质量浓度小于等于400.00 mg/m3的锅炉占76％,NOx平均排放质量浓度为324.60 mg/m3；燃油锅炉中NOx排放质量浓度小于等于400.00 mg/m3的锅炉占84％...     

应用三级燃烧方法实现大幅度降低燃煤电站锅炉的NOX排放量

本文简要介绍了锅炉燃烧过程中，NOX产生的主要类型及采用二级燃烧、浓淡燃烧来控制NOX排放量的方法，着重介绍了实现大幅度降低燃煤电站锅炉NOX排放量的三级燃烧方法。     

锅炉排污水用于烟气脱硫脱氮

长期以来，由于燃煤烟气中排放的SO2和NO2对大气造成了严重污染，据有关资料报道，在全世界每年排放的有害气体中仅SO2就达1．46亿t，占有害气体总排放量的24％左右，而SO2排放的70％是由燃煤锅炉产生的，在锅炉排烟中除SOx外，还有一定数量的NOx，NOx中NO对人体的危害最大。     

W型无烟煤锅炉氮氧化物排放浓度高的原因分析及解决实例

针对燃煤电厂W型火焰无烟煤锅炉普遍存在的NOx排放浓度高的问题进行了原因分析,与一般燃煤锅炉所排NOx以燃料型为主不同,该锅炉所排NOx的主要类型为热力型,炉膛燃烧温度高是热力型NOx产生量高的主要原因.通过对案例电厂煤质及炉型的分析找到了降低NOx排放的可行方法,对锅炉进行简单改造,掺烧烟煤可显著降低锅炉NOx产生量,通过试验确定掺烧烟煤的合适比例,为类似炉型提供参考.     

降低循环流化床锅炉污染物排放的措施

对循环流化床锅炉运行影响NOx和SO2生成的主要因素进行了分析,并提出了降低NOxSO2排放量的具体措施。     

切向燃煤锅炉新型低氮燃烧器的开发

在前墙燃烧锅炉中,通过高温还原火焰和火焰稳定技术已可使NOx排放量降到很低的程度,并已在切向燃烧中得到了应用,该技术与燃尽风系统相结合可得到更高的脱氮效率,飞灰中未燃炭的含量仍然可以保持很低,这种低氮燃烧器的脱氮效率为50％－80％,在实际运行的锅炉上使用时NOx(以NO2计）排放量可降低到50－70mg/MJ,该技术不仅用于燃烟煤的锅炉,还可用于燃褐煤的锅炉。     

炼化企业自备电厂燃煤锅炉烟尘超低排放改造技术

国家要求燃煤电厂锅炉要逐步改造为超低排放,相比新建锅炉或大型电厂锅炉,炼化企业自备电厂锅炉改造难度大。本文通过对炼化企业电厂锅炉现有环保设施和排放现状进行分析,对比了脱硫塔前干式除尘、塔内提级增效、塔后深度除尘等3种工艺技术方案的效果,结合已改造实例指出需关注设备腐蚀、SO3脱除、在线监测等方面问题,并提出深度改造技术方案和实施路线。     

浅议碳排放与废钢铁的节能减排功效

二氧化碳是导致全球气候变暖、人类生存环境恶化的主要原因。简要介绍世界钢铁工业二氧化碳排放情况,针对我国钢铁工业碳排放的具体情况,提出发展我国废钢产业,提高废钢铁的供应能力,是我国钢铁工业摆脱危机,实现低碳发展、绿色发展的主要途径。     

Synthesis and identification of graft copolymers of wood pulp and styrene

Based on the graft copolymerization reactions of lignin and vinyl monomers, a series of graft copolymers of wood pulp and styrene (1-phenylethene) has been synthesized. The wood pulps used in this research are unbleached products produced by chemical, thermal, and mechanical pulping. All of them contain a high content of lignin (25–29 wt%). The grafting reaction is a free radical polymerization coinitiated by calcium chloride, hydrogen peroxide, and wood pulp in dimethylsulfoxide at 30°C. The effect of reaction temperature, reaction time, and the amount of the reactants on the conversion of monomer, yield of product, weight increase of pulp, and grafting efficiency of monomer has been studied. The grafted wood pulp was separated from homopolystyrene formed during the reaction by extraction of the reaction product with benzene in a Soxhlet apparatus for at least 48 h. The results show that after the reaction, the weight of all wood pulps was significantly increased and the weight increase of very high yield sodium bisulfite pulp (VHYS) was 333%. This proves that a part of the polymerized styrene was chemically bound to the wood pulp. The Fourier transform infrared (FTIR) spectra of the extracted products show absorbance peaks characteristic of both wood and polystyrene and, thus, provide strong proof of grafting. Grafting has completely changed the surface properties of the starting wood pulp from hydrophilic to hydrophobic, and under ordinary thermal compression conditions, thermoplastic composite objects of good uniformity can be made directly from reaction products which contain up to 52 wt% wood pulp.     

Fate and effect of linuron and metribuzin on the co-composting of green waste and sewage sludge

The fate and effect of the herbicides linuron and metribuzin on the co-composting of sewage sludge and green waste were addressed in this work. The experiments were conducted in metal cubic containers of 1.0 m³ volume simulating a windrow composting system. A mixture of sludge and green waste was prepared at a ratio of 1:5 v/v. The mixture was split in four equal parts and the two herbicides were added, using a pressure sprayer, as sole or mixed pollutant in each of the three mixtures. The forth mixture was composted without any addition of herbicide, to serve as control. Temperature, physicochemical characteristics, herbicide concentration, carbon dioxide emission, methane emission and microbiological parameters were measured either daily or every time the mixtures were turned, for a period of 80 days. Both herbicides’ concentration decreased significantly resulting in removal efficiencies of 99.1–99.7% and 95.8–96.0% for linuron and metribuzin, respectively. Incubation of microbiologically inactive mixtures at a temperature schedule following the spontaneous temperature evolution in the composters resulted in very little (1–11%) decomposition for both herbicides. Comparison of the variation of physicochemical parameters and microbial populations during composting indicated that both herbicides did not affect the composting process.     

资源循环科学与工程专业课程体系优化与教学内容创新实践的探索

针对资源循环科学与工程本科专业课程教学,以西安建筑科技大学该专业课程体系为案例,通过对毕业生和专业研讨会调研,分析了课程体系建设的现状和存在的问题。借鉴其他高校资源专业的课程体系和教学内容,通过梳理各门专业课程的教学内容和相互联系,构建了资源专业课程体系课程群,探索了课程体系优化的方法和增加创新实践环节的具体措施。     

Photo-oxidation and Photo-toxicity of Crude and Refined Oils

The fate and effects of an oil spill are effected by solar radiation through the action of photo-oxidation and photo-toxicity. Photo-oxidation, an important process in the weathering of oil, produces a variety of oxidized compounds, including aliphatic and aromatic ketones, aldehydes, carboxylic acids, fatty acids, esters, epoxides, sulfoxides, sulfones, phenols, anhydrides, quinones and aliphatic and aromatic alcohols. Some of these compounds contribute to the marine biota toxicity observed after an oil spill. Photo-toxicity occurs when uptake of certain petroleum compounds, e.g. certain polycyclic aromatic hydrocarbons and benzothiophenes, is followed by solar exposure which results in much greater toxicity than after dark uptake. The mechanism of PAH photo-toxicity includes absorbance of solar radiation by the PAH which produces a free radical and this free radical in turn reacts with oxygen to produce reactive oxygen species that can damage DNA and other cellular macromolecules. While most studies on photo-toxicity have been carried out in the laboratory, there are studies showing that water from an oil spill is photo-toxic to bivalve embryos for at least a few days after the spill. Other studies have found that oil contaminated sediments are photo-toxic to several marine invertebrates. More studies are required to determine if marine fauna at an oil spill site are effected by the action of photo-toxicity and photo-oxidation.     

我国废旧电子电器产品拆解技术、设备应用现状及改进建议

从我国废旧电子电器回收行业基本情况、专业技术人才情况、相关企业拆解技术设备情况等方面，阐述了我国废旧电子电器产品拆解技术、设备应用现状，并提出相关改进提升建议。     

电子废弃物的再循环利用:企业、政府与公众的角色和责任

电子废弃物不仅种类繁多,而且成分复杂,含有多种有毒、有害物质,已成为固体废物中最大的重金属污染源.长期以来,由于对电子废弃物问题缺乏足够认识和有效管理,电子废弃物对人体健康及生活环境可能构成的危害常常被忽视.实现电子废弃物的再循环利用,关键是明确企业、政府和公众在电子产品设计、生产、消费、回收、处置和再利用整个过程中的相关责任.因此,解决电子废弃物的问题,首先要对相关行为主体的角色进行准确定位.     

TEMPO-Mediated Oxidation of Norway Spruce and Eucalyptus Pulps: Preparation and Characterization of Nanofibers and Nanofiber Dispersions

This study deals with 2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPO)-mediated oxidation of cellulose. Softwood and hardwood pulp fibers were suspended in water and oxidized to various extents at pH 10 and 22 °C using sodium hypochlorite in the presence of TEMPO radical and sodium bromide. This reaction system is known to be the most efficient one for the introduction of both surface carboxyl and aldehyde groups. Important relationships between formation of these functional groups and the fibrillation yield, light transmittance of the water dispersions and degree of polymerization of the oxidized softwood and hardwood pulps were established in the present study. A birefringence test confirmed the presence of nanofibers which according to atomic force microscopy analyses had diameters in the 1.6–3.8 nm range.     

Laboratory Experiments and Estimation of Cumulative Infiltration and Sorptivity

Soil water cumulative infiltration affects the environment by controlling the irrigation rate and consequently the water and pollutants movement through the ground. In order to study the cumulative infiltration in a sandy soil sample, experiments were performed in the laboratory. The sample was placed uniformly in a transparent column with an inner diameter of 6 cm. A constant head boundary condition of a 2 mm height was applied on the surface of the sample and the cumulative volume of the incoming water was measured. Soil moisture at four locations of the column was measured, by using the TDR method in order to obtain the moisture profiles. By comparing the values of the infiltrated water volumes with those calculated by the integration of the moisture profiles, a good agreement was found out. Also the Parlange theoretical model fitted very well with the infiltration experimental points.     

硫磺回收装置扩能改造及效果分析

介绍了回收酸性气体生产硫磺的工艺原理与工艺流程,论述了影响硫磺回收装置生产能力的诸多因素与扩能改造的情况。扩能改造后,该装置的酸性气体处理量平均为976m^3／h,瞬时处理量可达1200m^3／h,硫磺的生产能力从4450t／a提高到7500t／a,生产能力提高了68．5％,装置总硫回收率达到93．5％。