Exploration of the Effect of Chitosan and Crosslinking Agent Concentration on the Properties of Dual Responsive Chitosan-g-Poly (N-Isopropylacrylamide) Co-polymeric Particles

The objective of the present study was to synthesize and evaluate the effect of change in concentration of chitosan (CS) and N,N-methylenebisacrylamide (MBA)- a cross linking agent, on various properties such as lower critical solution temperature (LCST), zeta potential, particle size and poly dispersity index (PDI) of the synthesized co-polymer. Nine different formulations of chitosan-g-poly (N-isopropylacrylamide) (CS-g-PNIPAAm) co-polymer with varying CS and MBA concentrations were synthesized by a surfactant free dispersion copolymerization method. The synthesized co-polymer was further characterized and confirmed for its structure, morphology, particle size, zeta-potential, thermo and pH responsive properties, in-vitro cyto-compatability and stability studies using various analytical tools. The data confirms the successful synthesis of co-polymer. The increase in the concentrations of CS and MBA during the polymerization of co-polymer, resulted in proportional increase of LCST and zeta potential with decrease in particle size of co-polymeric nanoparticles. pH responsive studies showed that as the pH of the medium increases particle size and zeta potential decreases with increase in LCST of co-polymeric nanoparticles. From the results, it can be inferred that the synthesized co-polymeric nanoparticles exerted thermo and pH responsive properties with biocompatibility. By varying the CS and MBA concentrations in the co-polymer, desired LCST, particle size and zeta potential for co-polymeric nanoparticles can be obtained and thus the synthesized co-polymer may have great potential to be used as a drug carrier (nanoform) with both thermo and pH responsiveness.     

Green Synthesis of Silver Nanoparticles and Study of Their Antimicrobial Properties

One of the major disadvantages of polymers when used in food-contact applications is that they are very susceptible to microbial attack. On the other hand, silver nanoparticles have received increased attention as novel antimicrobial agents. Therefore, the introduction of silver nanoparticles into conventional polymers results in new materials with improved properties. In this investigation, colloidal silver nanoparticles using an environmentally friendly procedure were synthesized. An aqueous solution of AgNO₃ was used as a silver precursor with ‘green’ reducing agents either different types of honey, or β-d-glucose. In the first case, different pH values, as well as the addition of poly(ethylene glycol), PEG were studied, while in the latter, the effect of reduction time in the presence of PEG with various average molecular weights was examined. Properties of the nanoparticles were measured using X-Ray diffraction, UV–Vis and FTIR spectroscopy. Using honey it seems that spherical particles are produced with the smaller average particle size obtained at pH 8.5. Use of honey has the advantage of being a natural product, although its main drawback is that its composition varies and it cannot be predefined to result in reproducible results. Use of β-d-glucose results in stable silver nanoparticles with small average particle size after 24 h reduction. The addition of low molecular weight PEG seems to be beneficial in the production of stable nanoparticles. Finally, the antimicrobial activity of the nanoparticles produced was investigated at different concentrations on both Gram positive and negative bacteria, such as Bacillus cereus, Bacillus subtilis, Escherichia coli and Staphylococcus aureus.     

Chitosan/Hydrophilic Plasticizer-Based Films: Preparation,Physicochemical and Antimicrobial Properties

The addition of plasticizers to biopolymer films is a good method for improving their physicochemical properties. The aim of this study was to evaluate the effect of chitosan (CHI) blended with two hydrophilic plasticizers glycerol (GLY) and sorbitol (SOR), at two concentrations (20 and 40 wt%) on their mechanical, thermal, barrier, structural, morphological and antimicrobial properties. The chitosan was prepared through the alkaline deacetylation of chitin obtained from fermented lactic from shrimp heads. The obtained chitosan had a degree of deacetylation (DA) of 84 ± 2.7 and a molecular weight of 136 kDa, which indicated that a good film had formed. The films composed of CHI and GLY (20 wt%) exhibited the best mechanical properties compared to the neat chitosan film. The percentage of elongation at break increase to over 700 % in the films that contained 40 % GLY, and these films also exhibited the highest values for the water vapor transmission rate (WVTR) of 79.6 ± 1.9 g m² h^?1 and a yellow color (b _o  = 17.9 ± 2.0) compared to the neat chitosan films (b _o  = 8.8 ± 0.8). For the structural properties, the Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction analyses revealed an interaction in the acetamide group and changes in the crystallinity of plasticized films. The scanning electron micrographs revealed that all formulations of the chitosan films were smooth, and that they did not contain aggregations, pores or microphase separation. The thermal analysis using differential scanning calorimetry (DSC) revealed a glass transition temperature (Tg) of 130 °C for neat chitosan film, but the addition of SOR or GLY elicited a decrease in the temperature of the peak (120 °C). In addition, the antimicrobial activity of the chitosan films was evaluated against Listeria monocytogenes, and reached a reduction of 2 log after 24 h. The plasticizer concentration of 20 % GLY is sufficient for obtaining flexible chitosan films with good mechanical properties, and it could serve as an alternative as a packaging material to reduce environmental problems associated with synthetic packaging films.     

Laboratory waste minimization by recovery of silver as nano-silver colloidal dispersion from waste silver chloride

The use of cyclic experiments, where the product of one reaction becomes the starting material for the next experiment, was proposed as an effective protocol for waste minimization in an educational lab. A simple, cheap and pollution-free method was developed for recovering silver as nano-silver colloidal dispersion from waste silver chloride in the laboratories of the Faculty of Health, Safety and Environment. Silver nanoparticles of the size 5–18 nm were recovered in the presence of sodium borohydride as a reducing agent and polyvinylpyrrolidone as a stabilizer agent. The nano-silver particles were studied for their formation, structure, stability and size using UV–Vis spectroscopy, transmission electron microscopy and dynamic light scattering techniques. The antibacterial assays of nanoparticles showed satisfactory results for Escherichia coli ATCC25922, Staphylococcus aureus ATCC 29213, and Acinetobacter baumanii (Clinical isolate). A laboratory experiment was designed in which students synthesize yellow colloidal silver solution from chemical waste silver chloride and estimate particle size using visible spectroscopy.     

Effect of Varying Filler Concentration on Zinc Oxide Nanoparticle Embedded Chitosan Films as Potential Food Packaging Material

Prevailing scenario of non-biodegradable food packaging materials worldwide was the motivation for this research. More than half of the packaging materials used today are non-biodegradable and lack one or the other feature that keeps it from being an ideal food packaging material. Based on the current need of food grade packaging materials, the present study illustrates the amelioration of the properties of biodegradable chitosan films with the incorporation of zinc oxide (ZnO) nanoparticles in varying concentration. The ZnO nanoparticles (ZnONPs) used as fillers in the chitosan films were synthesized by supersaturation method. They were characterized using UV–visible spectrophotometry, X-ray diffraction and field emission scanning electron microscopy (FE-SEM). The particles were observed to be around 100–200 nm in size. The chitosan films with varying concentration of ZnONPs were synthesized and characterized using Fourier transform infrared spectroscopy and FE-SEM. The films were studied for their thermal stability, water vapor transmission rate (WVTR) and mechanical properties. The thermal stability, as determined by Thermo Gravimetric Analysis and Differential Scanning Calorimetry increased slightly with increasing percentage of embedded ZnONPs while a substantial decrease in WVTR was observed. Mechanical properties also showed improvements with 77% increment in tensile modulus and 67% increment in tensile strength. The antimicrobial activity of the films was also studied on gram positive bacterium Bacillus subtilis (B. subtilis) and gram negative bacterium Escherichia coli (E. coli) by serial dilution method. A twofold and 1.5-fold increment in the antimicrobial activity was observed for B. subtilis and E. coli, respectively, with increased ZnONPs concentration in the films from 0(w/w) to 2%(w/w). Films thus prepared can prove to be of immense potential in the near future for antimicrobial food packaging applications.     

Preparation and Characterization of Polyaniline and Ag/ Polyaniline Composite Nanoporous Particles and Their Antimicrobial Activities

Polyaniline (PANI) and Ag/PANI nanoporous composite were prepared by an oxidative polymerization method. The oxidation process of PANI nanoparticles was occurred using (NH₄)₂S₂O₈ while the oxidation process of Ag/PANI nanoporous composite was occurred using AgNO₃ under the effect of artificial radiation. The structural, morphological, and optical properties of the PANI and Ag/PANI nanoporous structures were studied using different characterization tools. The results confirm the formation of polycrystalline nanoporous PANI and spherical nanoporous composite of Ag/PANI particles. Antibacterial activity tests against gram-positive bacteria, Bacillus subtilis and Staphylococcus aureus, and gram-negative bacteria, Escherichia coli, and Salmonella species were carried out using different concentrations of PANI nanoparticles and Ag/PANI nanoporous composites. PANI has not antibacterial effect against all studied pathogens. In contrast, Ag/PANI nanoporous composites possessed antibacterial activity that is identified by the zone of inhibition. The inhibition zones of bacteria are in order; Salmonella species?>?S. aureus?>?B. subtilis?>?E. coli. The inhibition zones of all bacteria increased with increasing concentrations of Ag/PANI nanoporous composites from 200 to 400 ppm then decreased with further increasing of the dose concentrations to 600 ppm. Finally, a simplified mechanism based on the electrostatic attraction is presented to describe the antimicrobial activity of Ag/PANI nanoporous composite.     

The Influence of Artificial Photodegradation on Properties of Poly(3-hydroxybutyrate-<Emphasis Type="Italic">co</Emphasis>-3-hydroxyvalerate)(PHBV)/Graphite Nanosheets (GNS) Nanocomposites

The potential use of poly(3-hydroxybutyrate-co-3-hydroxyvalerate)/graphite nanosheets (GNS) as a biodegradable nanocomposite has been explored. PHBV/GNS nanocomposites films were prepared by solution casting at various concentrations of GNS—0.25, 0.50 and 1.00 wt% GNS. The films were exposed to artificial ultraviolet radiation (UV) during 52 h. The effect of GNS on PHBV photodegradation was investigated and compared to neat PHBV film. The artificial photodegradation induced changes in physical (weight loss), chemical carbonyl index by Fourier transform infrared spectroscopy, thermal degree of crystallinity and melting temperature by differential scanning calorimetry and morphological scanning electron microscopy characteristics. Based on the results obtained from aforementioned analyzes it was verified that GNS inhibits the oxidative degradation of PHBV matrix.     

Green Synthesis and Antioxidant Study of Silver Nanoparticles of Root Extract of <Emphasis Type="Italic">Sageretia thea</Emphasis> and Its Role in Oxidation Protection Technology

Development of environmentally friendly synthesis of nanoparticles is one of the important areas of research in nanotechnology. In present study silver naopartticles (AgNPs) of root extract of Sageretia thea (S. thea) were synthesized at room temperature. The synthesized AgNPs were characterized by UV. Visible spectroscopy (UV), scanning electron microscopy (SEM), X-ray diffraction (XRD), energy dispersive spectroscopy (EDX), transmission electron microscopy (TEM), dynamic light scattering (DLS) and Fourier transform infrared (FT-IR) spectroscopy. Formation of AgNPs was confirmed by visual examination the colour change from yellow to brick red due to surface Plasmon resonance band at 435 nm. SEM and TEM analysis of synthesized AgNPs revealed spherical morphology with average particle size 25 nm. Crystalline nature of the AgNPs in face centered cubic structure is evident from the selected area electron diffraction (SAED) and XRD pattern. The presence of elemental Ag was confirmed by EDX analysis at 3kv. Different functional groups which responsible for reduction and stabilization of reaction medium was confirmed by FTIR spectroscopy. The biosynthesized AgNPs showed strong DPPH and dye protection radical scavenging assay while modest hydrogen peroxide radical scavenging assay as compare to crude extract. The present investigations suggest that biosynthesized nanoparticles have a high potential for use in the preparation of drugs used against various diseases and also a promising candidate for many medical applications.     

Stability of Aqueous Suspensions of Medium-Chain-Length Poly-3-Hydroxyalkanoate Particles

Although poly-3-hydroxyalkanoates (PHAs) and particularily medium-chain-length (mcl)-PHAs are likely to find industrial applications in a latex form, very few studies have examined their behavior in aqueous suspension and none have examined the dense suspensions required commercially. For this reason, the stability of mcl-PHA latexes containing saturated aliphatic (65 mol% 3-hydroxynonanoate, PHN), and for the first time, with vinyl (PHNU) or carboxylated side chains was examined. At 4 g L^?1 with no stabilizing agent, PHNU nanoparticles (199.4 ± 3.6 nm) were significantly smaller than those of PHN (211.5 ± 6.4 nm) while carboxylated PHN nanoparticles (76.1 ± 6.4 nm) were substantially smaller than those of either PHN or PHNU with particles stable for more than 110 days. Increasing the PHN concentration to 10 g L^?1 also resulted in stable latexes but with larger particles (410.8 ± 5.2 nm). Adjusting the pH of the suspending medium (water) before addition of the polymer (dissolved in acetone) resulted in much smaller PHN particles at pH = 11.3 (134 ± 2 nm) than at pH = 4.3 (312 ± 8 nm) at a 4 g L^?1 final polymer concentration. Zeta potentials of PHN suspensions decreased with pH, likely due to the carboxyl end groups. Above a pH of 4.0, adjusting the pH after particle formation had little effect. NaCl addition could be used to agglomerate and ultimately precipitate the particles. Stabilizers such as surfactants will likely be required to produce denser mcl-PHA latexes with suitable particle size for certain applications such as coatings and toner production.     

Formulation and Evaluation of Matrix Type Transdermal Patch Containing Silver Nanoparticles

This research aimed to prepare the silver nanoparticles (AgNPs)-loaded antimicrobial wound dressing patch using ethyl cellulose as a matrix membrane and diethyl phthalate as a plasticizer. The polymer suspension was homogeneously mixed with plasticizer, and then added to the colloidal AgNPs suspension. This mixture was poured into Petri dish and subsequently dried in a hot air oven at 80?±?2 °C for 10 h. The minimum inhibition concentration of the colloidal AgNPs suspension was 2.5 µg/ml. The AgNPs-loaded antimicrobial wound dressing patch was evaluated for physical properties by differential scanning calorimeter, X-ray diffraction, scanning electron microscope, and in vitro study. The antimicrobial wound dressing patch did not exhibit any interaction between the matrix membrane and AgNPs. The AgNPs were evenly dispersed in the patch. The patch could control the release of silver at 102.98?±?4.11% over 12 h. Although the AgNPs-loaded antimicrobial wound dressing patches can be easily prepared by the simple method, in future studies antimicrobial wound dressing patch will be developed by employing different types of film forming agents.     

A novel method for the preparation of silver/chitosan-O-methoxy polyethylene glycol core shell nanoparticles

Uniformly sized silver/chitosan-O-methoxy polyethylene glycol (chitosan-O-MPEG) core shell nanoparticles with different degree of substitution were synthesized. Thus, N-phthaloyl chitosan is reacted with polyethylene glycol monomethyl ether iodide in the presence of silver oxide by the following steps. At first, amino groups of chitosan are protected by fourfold excess of phthalic anhydride. Then N-phthaloyl chitosan is reacted with an appropriate amount of monomethyl ether iodide in the presence of silver oxide and lastly N-phthaloyl groups are removed to yield silver/chitosan-O-MPEG core shell nanoparticles. Structure of prepared silver/chitosan-O-MPEG core shell nanoparticles have been characterized by UV/Vis spectroscopy, transmission electron microscopy (TEM), Fourier transform infrared (FT-IR), X-ray diffraction, and scan electron microscopy (SEM-EDX). Experimental results revealed that the prepared silver core particles had the size 18?±?2?nm. Core shell structure with chitosan-O-MPEG-coating had the size 40?±?2?nm.     

Recycling of the hyperaccumulator Brassica juncea L.: synthesis of carbon nanotube-Cu/ZnO nanocomposites

The methods of synthesizing carbon nanotube (CNTs)-Cu/ZnO nanocomposites using a Cu hyperaccumulator (Brassica juncea L.) constitute a new insight into the recycling of hyperaccumulators and provide a new route for the further development of green nanostructure syntheses. In this paper, CNTs-Cu/ZnO nanocomposites have been synthesized using B. juncea plants as the sources of C, Cu, and Zn. The synthesized CNTs-Cu/ZnO nanocomposites were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive spectra (EDS). The synthesized CNTs were characterized further by selected area diffraction (SAD) patterns and Raman spectroscopy. The results demonstrated that the structure of individual CNTs was middle-hollow, with an outer diameter of about 80 nm. The synthesized CNTs were not at all crystalline and there were a few defects in the walls. The outer diameter of CNTs-Cu/ZnO nanocomposites was 110 nm. The diameters of Cu/ZnO nanoparticles were 29.5/32.7 nm, respectively. Cu/ZnO nanoparticles that had grown onto the CNT surface were nonuniform and agglomerated. The Cu/ZnO nanoparticles were pure.     

Effect of Gamma Radiation on the Properties of Crosslinked Chitosan Nano-composite Film

Chitosan nano-composite film crosslinked by citric acid and with glycerol as plasticizer and MgO as antibacterial agent was prepared by casting method. MgO nanoparticles were synthesized via calcination method in furnace at 500 °C for 4 h and characterized by X-ray diffraction and transmission electron microscope. The chitosan nano-composite film with composition chitosan/citric/glycerol/magnesium oxide (1 wt%:1 wt%:75 vol%:10 wt%) has high mechanical properties than other films. The effects of different irradiation doses on the mechanical, thermal and antibacterial activity were investigated. The tensile strength enhanced by increasing irradiation dose up to 10 kGy and the elongation negligible changed as irradiation dose increased. The thermal stability slightly increased up to dose 2.5 kGy then decreased with dose increment. The antimicrobial activity film was studied against white mulberry-borne bacterial pathogens either Gram positive or Gram negative bacteria and has positive impact of gamma irradiation on the antimicrobial activity. The use of the selected chitosan nano-composite film which irradiated by dose of 2.5 kGy and has magnesium oxide of average particle size 54.3 nm as new packaging materials found to improve storage quality and shelf-life of mulberry fruit.     

Biodegradation Study of Starch-graft-Acrylonitrile Copolymer

In this study the biodegradability of starch-graft-acrylonitrile (St-g-AN) copolymer has been investigated using some microorganisms including Aspergillus niger. The fungus A. niger was isolated from the soil and from the wastewater of an acrylic fiber company. The effects of four factors including environment temperature, primary inoculum concentration, pH and weight of copolymer film, on the biomass generation as a measure of biodegradation rate of copolymer, were studied using Taguchi experimental design. The statistical analysis of the results showed that the primary inoculum concentration and temperature were the most important factors affecting the biodegradation of St-g-AN copolymer. The optimum levels of temperature, pH, inoculum concentration, and weight of films to attain the maximum biodegradation (as much as 8.59 % by weight percentage during 28 days) were obtained as 30 °C, 4.75, 10⁸ spore/mL, and 1.1 g, respectively. The changes in the structure and morphological properties of the copolymer before and after degradation were determined using transform infrared spectroscopy and scanning electron microscopy.     

Synthesis of CS/PVA Biodegradable Composite Nanofibers as a Microporous Material with Well Controllable Procedure Through Electrospinning

In this study, we have showed a facile route for fabrication of a novel microporous material based on chitosan (CS) and poly(vinyl alcohol) (PVA) biodegradable nanofibers that have high specific surface area, considerable porosity, and small diameter. Scanning electron microscopy, thermogravimetric analysis, differential scanning calorimetry, fourier transform infrared spectroscopy, Brunauer–Emmett–Teller surface area analysis, and CHNS/O elemental analyser were applied to characterize the fabricated CS/PVA composite nanofibers. Moreover, the influences of spinning conditions including concentration, voltage, electrospinning distance, and flow rate, on size distribution and pore diameter of the final product were systematically studied using 2^k?1 factorial design experiments, and the response surface optimization was used for determining the best synthesis parameter. The results obtained from 2^K?1 factorial design experiments showed that electrospinning parameters influenced the size distribution and pore diameter of the CS/PVA microporous material. Based on the response surface methodology, the CS/PVA product could be obtained with a high microporous diameter of 1.8 nm and a small diameter distribution of 15.0 nm under optimized conditions. The obtained results showed that the fabricated samples could be utilized in different applications.     

Facile Preparation of Chitosan Films for High Performance Removal of Reactive Blue 19 Dye from Aqueous Solution

This study aimed at finding effective strategies for high-performance removal of reactive blue 19 (RB19) dye from aqueous solution. Chitosan (CS) films had been prepared by using solvent casting with mild drying for this purpose. The CS films were characterized by X-ray diffraction, field-emission scanning electron microscopy, and Fourier transform infrared (FTIR) spectroscopy. The performance of RB19 removal using CS were evaluated by varying contact time, solution pH, initial dye concentration, and adsorbent dosage. Adsorption isotherms, kinetics, and desorption were investigated by batch experiments. Results showed that CS films exhibited the optimal adsorption performance for RB19 removal and high maximum adsorption capacities of RB19, which were 799 and 822.4 mg g^?1 at 20 and 40 °C, respectively. Adsorption kinetic data were well described by the pseudo-second-order kinetic model. FTIR analyses further indicated that interactions between RB19 and the CS film occurred during adsorption. The CS films also exhibited satisfactory desorption of RB19 at about 80 % after 30 min of desorption at pH 11. Our study demonstrated that the CS films can be easily prepared and applied for effective removal of RB19 in treatment of wastewater.     

Characterization of Super Paramagnetic Nanoparticles Coated with a Biocompatible Polymer Produced by Dextransucrase from <Emphasis Type="Italic">Weissella cibaria</Emphasis> JAG8

Magnetic nanoparticles (MNPs) synthesised by chemical co-precipitation method was subjected to dextran coating by sonication method. The dextran was enzymatically synthesised by extracellular dextransucrase isolated from Weissella cibaria JAG8. The crystalline nature of MNPs and dextran coated MNPs were confirmed by X-ray diffraction studies with average particle size of 25 nm, which was confirmed further by high resolution transmission electron microscopy. The surface morphology of MNPs and dextran coated MNPs were monitored by scanning electron microscopy studies. The vibrating sample magnetometer investigation displayed the super paramagnetic nature of MNPs and dextran coated MNPs. FT-IR analysis of MNPs and dextran coated MNPs, displayed characteristic band of Fe–O bond at 582 cm^?1. Thermo-gravimetric analysis of MNPs and dextran coated MNPs (1:1) ratio displayed a weight loss of 15 and 18 %, which clearly indicated 3.0 % of dextran was coated on to the MNPs. The elemental composition study by scanning electron microscopy confirmed the association of dextran with MNPs. The in vitro effect of MNPs and dextran coated MNPs was performed on human colon cancer (HT-29) cell lines and the results showed that dextran coated: MNPs (2:1) displayed good biocompatibility results over dextran coated: MNPs (1:1) and un-coated MNPs.     

Phosphogypsum Waste Used as Reinforcing Fillers in Polypropylene Based Composites: Structural,Mechanical and Thermal Properties

The industrial production of wet phosphoric acid in Morocco led to controversial stockpiling of waste phosphogypsum by-products resulting in the release of significant amounts of toxic impurities in salt marshes. In the framework of fighting against global climate change and efforts to reduce toxic industrial wastes (phosphate industry), this work presents a new polymer composite based on phosphogypsum (PhG) and polypropylene (PP).The compounds were produced by twin-screw extrusion and injection molding. The morphological results show that good affinity between PhG and PP led to good particle dispersion/distribution in the polymer matrix. Thermal characterizations showed that PhG particles improved the thermal stability of PP with a 50 °C increase at 40 wt%. The optimum tensile modulus was also obtained at 40 wt% with a 74 % increase over neat PP. Dynamical mechanical analysis showed that PhG addition can improve the viscoelastic properties of PP for potential applications under dynamic stress. Overall, it can be concluded that PhG is potential reinforcing filler for the production of PP composites and represents a promising avenue for the valorization of this waste as a new raw material while resolving some environmental issues.     

Preparation and Properties of a Chitosan–Hyaluronic Acid-Polypyrrole Conductive Hydrogel Catalyzed by Laccase

Electro conductive hydrogels, consisting of chitosan (CS), hyaluronic acid (HA), and polypyrrole (PPy), were prepared via an in situ enzymic polymerization of pyrrole in the CS–HA hydrogel, using laccase as the catalyst. This CS–HA–PPy composite hydrogel showed good conductivity. The chemical structure and morphology of this conductive hydrogel were studied by Fourier transform infrared spectroscopy, scanning electron microscopy, and X-ray diffraction technique. For CS–HA–PPy and CH–HA hydrogel, the temperature at which fastest decomposition occurred was 260 and 244 °C, respectively. That means the thermal stability of CS–HA–PPy is better than CS–HA hydrogel. The conductive hydrogel also showed excellent swelling and deswelling behaviors.     

Extraction and Characterization of Nanocrystalline Cellulose from Doum (<Emphasis Type="Italic">Chamaerops humilis</Emphasis>) Leaves: A Potential Reinforcing Biomaterial

The aim of this investigation was to extract nanocrystalline cellulose (NCC) from Moroccan Doum fibers (Chamaerops humilis) by chemical treatment to examine their potential for use as reinforcement fibers in bionanocomposite applications. The chemical composition, morphological and structural properties of the Doum fibers was determined at different stages of chemical treatment. Morphological (transmission electron microscopy and scanning electron microscopy), structural characterization (X-ray diffraction, Fourier transformed infrared), thermal characterization (thermogravimetric analysis). The suspension electrostatic stabilization (zeta potential) of NCCs was also carried out. The results of these characterization analysis found that average size of the NCC is 220 nm in length and 11 nm in diameter, with high crystallinity index (93 %), a thermal stability comparable to that of untreated Doum fibers (degradation temperature 340 °C), which is reasonably promising for the use of these nanofibers in reinforced-polymer manufacturing, and a good stability in water suspension that it allows their utilization such as reinforcement of the water-soluble polymers to prepare the bio-nanocomposite.