A “convective” flow biofilter for the biofiltration of contaminants at sub‐low concentrations

Biofiltration of contaminants at concentrations below a certain level (sub‐low concentrations) is not as effective as at higher concentrations, which leads to incomplete removal of the contaminants, because of diffusive mass transfer of the contaminants inside the biofilm and insufficient carbon and energy sources to sustain biomass growth and maintenance. To overcome the limitation of diffusion, this article proposes the concept of convective flow biofilm in which contaminated air flows through the porous biofilm and thus carries the carbon and energy sources to the biomass. The innovative concept of convective flow biofilm was implemented in a convective flow biofilter (CFB), which was built from activated carbon‐coated ceramic monoliths by selectively blocking the channel openings. The CFB was tested for 11 weeks for the biofiltration of toluene at inlet concentrations below 100 ppmv. The CFB performed consistently better than the conventional diffusive flow biofilter (DFB), as indicated by the higher removal efficiencies and the higher CO₂ productions. The CFB demonstrated up to 30 percent higher removal efficiency and an up to 100 percent higher elimination capacity than the DFB. © 2007 Wiley Periodicals, Inc.     

Formerly utilized sites remedial action program “completed” sites: Lessons for long‐term stewardship

The Formerly Utilized Sites Remedial Action Program (FUSRAP) covers inactive commercial, federal, and university facilities that once supported activities of the Manhattan Project or Atomic Energy Commission. Current responsibilities, established by a Memorandum of Understanding (MOU), are split between the U.S. Department of Energy (US DOE) and the U.S. Army Corps of Engineers. The MOU distinguishes between facilities remediated before 1997 (“completed” sites) and those where remediation remained to be completed at that time. This article evaluates activities conducted at completed sites with regard to considerations for long‐term stewardship, which is defined by the US DOE as all activities necessary to protect human health and the environment after remediation is considered complete. Experience with these FUSRAP sites provides “lessons learned” for the requirements of satisfactory long‐term stewardship. © 2007 Wiley Periodicals, Inc.     

Sustainable soil remediation by refrigerated condensation at sites with “high‐concentration” recalcitrant compounds and NAPL: Two case studies

Remediation of recalcitrant compounds at sites with high concentrations of volatile organic compounds (VOCs) or nonaqueous‐phase liquids (NAPLs) can present significant technical and financial (long‐term) risk for stakeholders. Until recently, however, sustainability has not been included as a significant factor to be considered in the feasibility and risk evaluation for remediation technologies. The authors present a framework for which sustainability can be incorporated into the remediation selection criteria focusing specifically on off‐gas treatment selection for soil vapor extraction (SVE) remediation technology. SVE is generally considered an old and standard approach to in situ remediation of soils at a contaminated site. The focus on off‐gas treatment technology selection in this article allows for more in‐depth analysis of the feasibility evaluation process and how sustainable practices might influence the process. SVE is more commonly employed for recovery of VOCs from soils than other technologies and generally employs granular activated carbon (GAC), catalytic, or thermal oxidation, or an emerging alternative technology known as cryogenic‐compression and condensation combined with regenerative adsorption (C3–Technology). Of particular challenge to the off‐gas treatment selection process is the potential variety of chemical constituents and concentrations changing over time. Guidance is available regarding selection of off‐gas treatment technology (Air Force Center for Environmental Excellence, 1996; U.S. Environmental Protection Agency, 2006). However, there are common shortcomings of off‐gas treatment technology guidance and applications; practitioners have rarely considered sustainability and environmental impact of off‐gas treatment technology selection. This evaluation includes consideration of environmental sustainability in the selection of off‐gas treatment technologies and a region‐specific (Los Angeles, California) cost per pound and time of remediation comparisons between GAC, thermal oxidation, and C3–Technology. © 2008 Wiley Periodicals, Inc.     

Editor's perspective‐‐‐Shale gas development: Environmental issues and opportunities

Many professionals in the environmental industry have questioned whether the rapid expansion in shale gas development, particularly in the Marcellus Shale Play, is providing business opportunities. While gas production is a routine practice, the development of shale gas requires a process (fracturing, or, more commonly, “fracing'') that uses chemicals and is far more intrusive to the subsurface environment than traditional gas production. In this Editor's Perspective, we evaluate the environmental issues surrounding shale gas development, with a specific focus on the Marcellus Shale Play because it is currently the most active play in the United States, from both the drilling and political perspectives. In addition, we examine where the business opportunities are likely to be for environmental professionals relative to shale gas development. © 2011 Wiley Periodicals, Inc.     

Perils of categorical thinking: “Oxic/anoxic” conceptual model in environmental remediation

Given ambient atmospheric oxygen concentrations of about 21 percent (by volume), the lower limit for reliable quantitation of dissolved oxygen concentrations in groundwater samples is in the range of 0.1–0.5 mg/L. Frameworks for assessing in situ redox condition are often applied using a simple two‐category (oxic/anoxic) model of oxygen condition. The “oxic” category defines the environmental range in which dissolved oxygen concentrations are clearly expected to impact contaminant biodegradation, either by supporting aerobic biodegradation of electron‐donor contaminants like petroleum hydrocarbons or by inhibiting anaerobic biodegradation of electron‐acceptor contaminants like chloroethenes. The tendency to label the second category “anoxic” leads to an invalid assumption that oxygen is insignificant when, in fact, the dissolved oxygen concentration is less than detection but otherwise unknown. Expressing dissolved oxygen concentrations as numbers of molecules per volume, dissolved oxygen concentrations that fall below the 0.1 mg/L field detection limit range from 1 to 10¹⁷ molecules/L. In light of recent demonstrations of substantial oxygen‐linked biodegradation of chloroethene contaminants at dissolved oxygen concentrations well below the 0.1–0.5 mg/L field detection limit, characterizing “less than detection” oxygen concentrations as “insignificant” is invalid. © 2012 Wiley Periodicals, Inc.     

Evaluation of soil-washing process for “unwashable” clays and silts from the palmerton zinc site

The Palmerton Zinc Site is a Superfund site in Palmerton, Pennsylvania. Its former mineral processing operations have contaminated nearby wells and soils with zinc and cadmium. Preliminary analysis of soil and dust sampling conducted in May 1991 has revealed that the dust poses a potential threat to human health. Based on the results of a previous study, which showed a high percentage of silt and clay in soils from Palmerton residential properties, it was concluded that soil washing is not likely to be a viable method to treat the soil and dust contamination in Palmerton. However, since the completion of this study, a soil-washing process for “unwashable” clays and silts has been developed. A residential soil sample from Palmerton, which had low concentrations of arsenic, cadmium, and lead, and a somewhat high concentration of zinc, was washed in a bench-scale version of this process. The results showed that the new soil-washing process for “unwashable” clays and silts may be a viable method to treat the soil and dust contamination in Palmerton, depending on the soil quality criteria concentrations selected for site cleanup.     

Developing Effective Decision Support for the Application of “Gentle” Remediation Options: The GREENLAND Project

Gentle remediation options (GRO) are risk management strategies/technologies that result in a net gain (or at least no gross reduction) in soil function as well as risk management. They encompass a number of technologies, including the use of plant (phyto‐), fungi (myco‐), and/or bacteria‐based methods, with or without chemical soil additives or amendments, for reducing contaminant transfer to local receptors by in situ stabilization, or extraction, transformation, or degradation of contaminants. Despite offering strong benefits in terms of risk management, deployment costs, and sustainability for a range of site problems, the application of GRO as practical on‐site remedial solutions is still in its relative infancy, particularly for metal(loid)‐contaminated sites. A key barrier to wider adoption of GRO relates to general uncertainties and lack of stakeholder confidence in (and indeed knowledge of) the feasibility or reliability of GRO as practical risk management solutions. The GREENLAND project has therefore developed a simple and transparent decision support framework for promoting the appropriate use of gentle remediation options and encouraging participation of stakeholders, supplemented by a set of specific design aids for use when GRO appear to be a viable option. The framework is presented as a three phased model or Decision Support Tool (DST), in the form of a Microsoft Excel‐based workbook, designed to inform decision‐making and options appraisal during the selection of remedial approaches for contaminated sites. The DST acts as a simple decision support and stakeholder engagement tool for the application of GRO, providing a context for GRO application (particularly where soft end‐use of remediated land is envisaged), quick reference tables (including an economic cost calculator), and supporting information and technical guidance drawing on practical examples of effective GRO application at trace metal(loid) contaminated sites across Europe. This article introduces the decision support framework. ©2015 Wiley Periodicals, Inc.     

1,4‐Dioxane Treatment Technologies

The chlorinated solvent stabilizer 1,4‐dioxane (DX) has become an unexpected and recalcitrant groundwater contaminant at many sites across the United States. Chemical characteristics of DX, such as miscibility and low sorption potential, enable it to migrate at least as far as the chlorinated solvent from which it often originates. This mobility and recalcitrance has challenged remediation professionals to redesign existing treatment systems and monitoring networks to accommodate widespread contamination. Furthermore, remediation technologies commonly applied to chlorinated solvent co‐contaminants, such as extraction and air stripping or in situ enhanced reductive dechlorination, are relatively ineffective on DX removal. These difficulties in treatment have required the industry to identify, develop, and demonstrate new and innovative technologies and approaches for both ex situ and in situ treatment of this emerging contaminant. Great strides have been made over the past decade in the development and testing of remediation technologies for removal or destruction of DX in groundwater. This article briefly summarizes the fate and transport characteristics of DX that make it difficult to treat, and presents technologies that have been demonstrated to be applicable to groundwater treatment at the field scale.  ©2016 Wiley Periodicals, Inc.     

Progress toward remediation of the Sydney Tar Ponds: A major Canadian PCB/PAH “superfund” site

The Muggah Creek estuary in Sydney, Nova Scotia, received liquid and solid wastes from a steel mill and its associated coke ovens for approximately 100 years. This resulted in pollution of soils and sediments with polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs), heavy metals, and other pollutants, including those in untreated domestic wastewaters. The Canadian federal and Nova Scotia provincial governments organized the Sydney Tar Ponds Agency (STPA) to develop a remediation approach for the Coke Ovens site soils and Sydney Tar Ponds sediments. The STPA developed a remediation approach for the Sydney Tar Ponds sediments, involving solidification/stabilization (S/S) through mixing cement and other materials into the sediments, and then capping them as a waste pile. High‐density polyethylene (HDPE) plastic sheeting vertical barriers are proposed to be used to divert groundwater and surface water from entering into the S/S‐treated sediments and to collect any water and associated pollutants released from the S/S‐treated sediments. The Coke Ovens site soils are proposed to be landfarmed to reduce some of the PAHs and other pollutants and then capped with a layer of soil. This remediation program is estimated to cost on the order of $400 million (CAN). This article presents a review of the significant potential problems with the STPA proposed remediation strategy of the Sydney Tar Ponds sediments and Coke Ovens site soils. © 2006 Wiley Periodicals, Inc.     

Full‐scale bioremediation of a dilute 50‐acre plume

Enhanced anaerobic dechlorination is being conducted to remediate a 50‐acre groundwater area impacted with chlorinated volatile organic compounds (CVOCs). The plume, which is over 3,000 feet (ft) long, initially contained tetrachloroethene and breakdown products at concentrations of 2 to 3 milligrams per liter. The site's high groundwater flow velocity (greater than 1,000 ft per year) was incorporated into the design to help with amendment distribution. Bioaugmentation was conducted using a mixed culture containing Dehalococcoides ethenogenes. There is evidence that it has migrated to distances exceeding 600 ft. The major benefit of the high groundwater flow velocity is greater areal coverage by the remediation system, but the downside is the difficulty in delivering sufficient donor to create the required anaerobic conditions. Overall performance has been excellent with total CVOC reductions and conversion to ethene of 98 percent within a 25‐acre area downgradient of the treatment transect that has operated the longest. © 2011 Wiley Periodicals, Inc.     

Breakthrough in 2D‐CSIA Technology for 1,4‐Dioxane

A dual isotope technology based on compound‐specific stable isotope analysis of carbon and hydrogen (2D‐CSIA) was recently developed to help identify sources and monitor in situ degradation of the contaminant 1,4‐dioxane (1,4‐D) in groundwater. Site investigation and optimized remediation have been the focus of thousands of CSIA applications completed for volatile organic contaminants (VOCs) worldwide. CSIA for the water miscible 1,4‐D, however, has been technically challenging. The most commercially available sample preparation settings “Purge and Trap” for VOC could not efficiently extract 1,4‐D out of water for a reliable CSIA measurement, especially when the concentration is below 100 μg/L. Such a high reporting limit has prevented CSIA from being used for effective site investigation and remediation monitoring at most 1,4‐D contaminated sites, where 1,4‐D is often present at very low ppb levels. This article outlines the recent breakthrough in 2D‐CSIA technology for 1,4‐D in water, reported down to ～1 μg/L for carbon, and ～10 μg/L to 20 μg/L for hydrogen using solid‐phase extraction based on EPA Method 522, and its benefit is highlighted through a case study at a 1,4‐D contaminated site. ©2016 Wiley Periodicals, Inc.     

Complete Degradation of Hexahydro‐1,3,5‐Trinitro‐1,3,5‐Triazine (RDX) by a Co‐Culture of Gordonia sp. KTR9 and Methylobacterium sp. JS178

The presence of hexahydro‐1,3,5‐trinitro‐1,3,5‐triazine (RDX) in soil and groundwater is a major contamination issue at many military facilities around the world. Gordonia sp. KTR9 metabolizes RDX as a nitrogen source for growth producing 4‐nitro‐2,4‐diazabutanal (NDAB) as a dead‐end product. Methylobacterium sp. strain JS178 degrades NDAB as a sole source of nitrogen for growth. A mixed culture of strains KTR9 and JS178 was able to completely degrade RDX. There was no difference in rate of RDX degradation by KTR9 alone or in co‐culture with JS178. The first‐order degradation coefficients of RDX and NDAB in the co‐culture were 0.08 hr^?1 and 0.002 hr^?1, respectively. In the co‐culture that initially contained RDX plus NDAB, strain JS178 degraded the NDAB that was produced by KTR9 as shown by a decrease in the molar yield of NDAB (from RDX) from 1.0 to –0.11. Co‐cultures of strains KTR9 and JS178 could be used to promote complete degradation of RDX in soils or groundwater. ©2016 Wiley Periodicals, Inc.     

Stable Isotope Probing to Confirm Field‐Scale Co‐Metabolic Biodegradation of 1,4‐Dioxane

1,4‐Dioxane, a common co‐contaminant with chlorinated solvents, is present in groundwater at Site 24 at Vandenberg Air Force Base in California. Historical use of chlorinated solvents resulted in concentrations of 1,4‐dioxane in groundwater up to approximately 2,000 μg/L. Starting in 2013, an in situ propane biosparge system operation demonstrated reductions in 1,4‐dioxane concentrations in groundwater. The work detailed herein extends the efforts of the first field demonstration to a second phase and confirms the biodegradation mechanism via use of stable isotope probing (SIP). After two months of operation, 1,4‐dioxane concentrations decreased approximately 45 to 83 percent at monitoring locations in the test area. The results of the SIP confirmed ¹³C‐enriched 1,4‐dioxane was transformed into dissolved inorganic carbon (suggesting mineralization to carbon dioxide) and incorporated into microbial biomass (likely attributed to metabolic uptake of biotransformation intermediates or of carbon dioxide).  ©2016 Wiley Periodicals, Inc.     

Evaluation of natural attenuation at a 1,4‐dioxane‐contaminated site

1,4‐Dioxane entered the environment as a result of historic leaks and spills in the production area at an industrial facility in the southeastern coastal plain. The areal extent of the 1,4‐dioxane plume is several hundred acres and is largely contained on the site. Land use adjacent to the plant property is primarily undeveloped (wetlands or woods) or industrial, with a small area of mixed land use (commercial/residential) to the southwest and north. The surficial aquifer is a relatively simple hydrogeologic system with well‐defined boundaries and is comprised of a 50‐ to 70‐foot‐thick deposit of alluvial/fluvial sand and gravel that overlies an aquitard in excess of 100 feet thick. A groundwater flow model, developed and calibrated using field‐measured data, was used for the fate‐and‐transport modeling of 1,4‐dioxane. The flow‐and‐transport model, combined with the evaluation of other site geochemical data, was used to support the selection of monitored natural attenuation (MNA) as the proposed groundwater remedy for the site. Since the active sources of contamination have been removed and the modeling/field data demonstrated that the plume was stable and not expanding, the proposed MNA approach was accepted and approved by the regulatory agency for implementation in 2004. Subsequent accumulated data confirm that concentrations in the 1,4‐dioxane plume are declining as predicted by the fate‐and‐transport modeling. © 2008 Wiley Periodicals, Inc.     

ART in‐well technology proves effective in treating 1,4‐dioxane contamination

A common industrial solvent additive is 1,4‐dioxane. Contamination of dissolved 1,4‐dioxane in groundwater has been found to be recalcitrant to removal by conventional, low‐cost remedial technologies. Only costly labor and energy‐intensive pump‐and‐treat remedial options have been shown to be effective remedies. However, the capital and extended operation and maintenance costs render pump‐and‐treat technologies economically unfeasible at many sites. Furthermore, pump‐and‐treat approaches at remediation sites have frequently been proven over time to merely achieve containment rather than site closure. A major manufacturer in North Carolina was faced with the challenge of cleaning up 1,4‐dioxane and volatile organic compound–impacted soil and groundwater at its site. Significant costs associated with the application of conventional approaches to treating 1,4‐dioxane in groundwater led to an alternative analysis of emerging technologies. As a result of the success of the Accelerated Remediation Technologies, LLC (ART) In‐Well Technology at other sites impacted with recalcitrant compounds such as methyl tertiarybutyl ether, and the demonstrated success of efficient mass removal, an ART pilot test was conducted. The ART Technology combines in situ air stripping, air sparging, soil vapor extraction, enhanced bioremediation/oxidation, and dynamic subsurface groundwater circulation. Monitoring results from the pilot test show that 1,4‐dioxane concentrations were reduced by up to 90 percent in monitoring wells within 90 days. The removal rate of chlorinated compounds from one ART well exceeded the removal achieved by the multipoint soil vapor extraction/air sparging system by more than 80 times. © 2005 Wiley Periodicals, Inc.     

Re‐evaluation of treatment approach for a site contaminated with Freon‐113 and 1,1,1‐trichloroethane

This study demonstrates a remedial approach for completing the remediation of an aquifer contaminated with 1,1,2‐trichlorotrifluoroethane (Freon‐113) and 1,1,1‐trichloroethane (TCA). In 1987, approximately 13,000 pounds of Freon‐113 were spilled from a tank at an industrial facility located in the state of New York. The groundwater remediation program consisted of an extraction system coupled with airstripping followed by natural attenuation of residual contaminants. In the first phase, five recovery wells and an airstripping tower were operational from April 1993 to August 1999. During this time period over 10,000 pounds of CFC‐13 and 200 pounds of TCA were removed from the groundwater and the contaminant concentrations decreased by several orders of magnitude. However, the efficiency of the remediation system to recover residual Freon and/or TCA reduced significantly. This was evidenced by: (1) low levels (< 10 ppb) of Freon and TCA captured in the extraction wells and (2) a slight increase of Freon and/or TCA in off‐site monitoring wells. A detailed study was conducted to evaluate the alternative for the second‐phase remediation. Results of a two‐year groundwater monitoring program indicated the contaminant plume to be stable with no significant increase or decrease in contaminant concentrations. Monitored geochemical parameters suggest that biodegradation does not influence the fate and transport of these contaminants, but other mechanisms of natural attenuation (primarily sorption and dilution) appear to control the fate and transport of these contaminants. The contaminants appear to be bound to the soil matrix (silty and clay units) with limited desorption as indicated by the solid phase analyses of contaminant concentrations. Results of fate and transport modeling indicated that contaminant concentrations would not exceed the action levels in the wells that showed a slight increase in contaminant concentrations and in the downgradient wells (sentinel) during the modeled timeframe of 30 years. This feasibility study for natural attenuation led to the termination of the extraction system and a transaction of the property, resulting in a significant financial benefit for the original site owner. © 2003 Wiley Periodicals, Inc.