Phenol removal from wastewater by adsorption on zeolitic composite

It is well known that adsorption is an efficient method of removal of various pollutants from wastewater. The present study examines the phenol removal from water by adsorption on a new material, based on zeolitic volcanic tuff. This compound contains zeolitic tuff and cellulose, another known adsorbent, in a mass ratio of 4 to 1. The performances of the new adsorbent composite were compared with those of a widely used adsorbent material, zeolitic volcanic tuff. The adsorbent properties were tested on batch synthetic solutions containing 1–10 mg L^?1 (1–10 ppm) phenol, at room temperature without pH adjustment. The influence of the adsorbent dose, pH and contact time on the removal degree of phenol from water was investigated. The experimental data were modeled using the Langmuir, Freundlich, and Temkin adsorption isotherms. The Langmuir model was found to best represent our data revealing a monolayer adsorption with a maximum adsorption capacity between 0.12 and 0.53 mg g^?1 at 25 °C, for 2.00 g of adsorbent, depending on the initial phenol concentration. The adsorption kinetic study was performed using a pseudo-first- and pseudo-second-order kinetic models illustrating that phenol adsorption on zeolite composite is well described by pseudo-first kinetic equations. Our results indicated that phenol adsorption on the new adsorbent composite is superior to that on the classic zeolite.     

Highly effective removal of 2,4-dinitrophenolic from surface water and wastewater samples using hydrophilic molecularly imprinted polymers

Novel hydrophilic molecularly imprinted polymers (MIPs) with high adsorption capacity were used as the sorbents to remove 2,4-dinitrophenol (2,4-DNP) from surface water and wastewater samples. Kinetic studies, dynamic adsorption and selectivity experiments of hydrophilic MIPs were investigated in this study. The results indicated that the maximum adsorption capacity of 2,4-DNP on hydrophilic MIPs was 138.9 mg g^?1 and kinetic experimental data were described by the pseudo-second-order model. Furthermore, the effects of flow rate, initial concentration, pH value, and humic acid on the removal efficiency of 2,4-DNP were optimized. Compared with the active carbon, carbon nanotube, C18 sorbents and common MIPs, the removal efficiency of hydrophilic MIPs (100 mg) was very high with all above 92 % even though the sampling volume was more than 1 L. Investigated results of five times adsorption–desorption cycles indicated hydrophilic MIPs were high stability. In a word, the obtained results demonstrated that hydrophilic MIPs could be used as the effective sorbents for 2,4-DNP removal in practical application.     

Removal and recovery of copper and nickel ions from aqueous solution by poly(methacrylamide-co-acrylic acid)/montmorillonite nanocomposites

Nanocomposite hydrogels based on poly(methacrylamide-co-acrylic acid) and nano-sized montmorillonite were prepared by aqueous dispersion and in situ radical polymerization. Optimum sorption conditions were determined as a function of montmorillonite content, contact time, pH, and temperature. The equilibrium data of Cu²⁺ and Ni²⁺ conformed to the Freundlich and Langmuir isotherms in terms of relatively high regression values. The maximum monolayer adsorption capacity of the nanocomposite hydrogel (with 3 wt% montmorillonite content), as obtained from the Langmuir adsorption isotherm, was found to be 49.26 and 46.94 mg g^?1 for Cu²⁺ and Ni²⁺, respectively, at contact time?=?60 min, pH?=?6.8, adsorbent dose?=?100 mg/ml, and temperature?=?318 K. Kinetic studies of single system indicated that the pseudo-second order is the best fit with a high correlation coefficient (R ²?=?0.97–0.99). The result of five times sequential adsorption–desorption cycle shows a good degree of desorption and a high adsorption efficiency.     

Alginate beads containing water treatment residuals for arsenic removal from water—formation and adsorption studies

Water treatment residuals (WTRs) produced in large quantities during deironing and demanganization of infiltration water, due to high content of iron and manganese oxides, exhibit excellent sorptive properties toward arsenate and arsenite. Nonetheless, since they consist of microparticles, their practical use as an adsorbent is limited by difficulties with separation from treated solutions. The aim of this study was entrapment of chemically pretreated WTR into calcium alginate polymer and examination of sorptive properties of the obtained composite sorbent toward As(III) and As(V). Different products were formed varying in WTR content as well as in density of alginate matrix. In order to determine the key parameters of the adsorption process, both equilibrium and kinetic studies were conducted. The best properties were exhibited by a sorbent containing 5 % residuals, formed in alginate solution with a concentration of 1 %. In slightly acidic conditions (pH 4.5), its maximum sorption capacity was 3.4 and 2.9 mg g^?1 for As(III) and As(V), respectively. At neutral pH, the adsorption effectiveness decreased to 3.3 mg As g^?1 for arsenites and to 0.7 mg As g^?1 for arsenates. The presence of carboxylic groups in polymer chains impeded in neutral conditions the diffusion of anions into sorbent beads; therefore, the main rate-limiting step of the adsorption, mainly in the case of arsenates, was intraparticle diffusion. The optimal condition for simultaneous removal of arsenates and arsenites from water by means of the obtained composite sorbent is slightly acidic pH, ensuring similar adsorption effectiveness for both arsenic species.     

Kinetics and the mass transfer mechanism of hydrogen sulfide removal by biochar derived from rice hull

The biochar derived from rice hull was evaluated for its abilities to remove hydrogen sulfide (H₂S) from gas phase. The surface area and pH of the biochar were compared. The biochar derived from rice hull was evaluated for its abilities to remove hydrogen sulfide (H₂S) from gas phase. The surface area and pH of the biochar were compared. The different pyrolysis temperature has great influence on the adsorption of H₂S. At the different pyrolysis temperature, the H₂S removal efficiency of rice hull-derived biochar was different. The adsorption capacities of biochar were 2.09 mg·g^–1, 2.65 mg·g^–1, 16.30 mg·g^–1, 20.80 mg·g^–1, and 382.70 mg·g^–1, which their pyrolysis temperatures were 100 °C, 200 °C, 300 °C, 400 °C and 500 °C respectively. Based on the Yoon-Nelson model, it analyzed the mass transfer mechanism of hydrogen sulfide adsorption by biochar.

Implications: The paper focuses on the biochar derived from rice hull–removed hydrogen sulfide (H₂S) from gas phase. The surface area and pH of the biochar were compared. The different pyrolysis temperatures have great influence on the adsorption of H₂S. At the different pyrolysis temperatures, the H₂S removal efficiency of rice hull–derived biohar was different. The adsorption capacities of biochar were 2.09, 2.65, 16.30, 20.80, and 382.70 mg·g^?1, and their pyrolysis temperatures were 100, 200, 300, 400, and 500 °C, respectively. Based on the Yoon-Nelson model, the mass transfer mechanism of hydrogen sulfide adsorption by biochar was analyzed.     

Adsorptive removal of Pb2+ form aqueous solution by macrocyclic calix[4]naphthalene: kinetic, thermodynamic, and isotherm analysis

Background

The adsorption characteristics of Pb²⁺ ions from aqueous solutions onto calix[4]naphthalene have been investigated.

Method

Calix[4]naphthalene was prepared by the condensation of 1-naphthol and formaldehyde (1:2) in presence of hydrochloric acid at 80°C. The effect of various operation parameters, such as solution pH, initial metal ion concentration, contact time, and temperature, on the adsorption capacity of calix[4]naphthalene for Pb²⁺ have been investigated.

Result

Experimental results showed that the adsorption of Pb²⁺ ions increased with the increase in solution pH and temperature. Langmuir and Freundlich isotherms models were used to describe the adsorption behavior of Pb²⁺ by calix[4]naphthalene. Equilibrium data fitted well with the Langmuir isotherm model and the maximum adsorption capacity of calix[4]naphthalene for Pb²⁺ at 30°C was found to be 29.15 mg g^?1. Kinetic studies indicated that the adsorption followed pseudo-second order model and the thermodynamic studies revealed that the adsorption process was spontaneous and endothermic in nature. The obtained results demonstrated that calix[4]naphthalene can be used as an effective adsorbent for Pb²⁺ ions removal from water.     

Effect of deposit age on adsorption and desorption behaviors of ammonia nitrogen on municipal solid waste

Ammonia nitrogen pollution control is an urgent issue of landfill. This research aims to select an optimal refuse for ammonia nitrogen removal in landfill from the point of view of adsorption and desorption behavior. MSW (municipal solid waste) samples which deposit ages were in the range of 5 to 15 years (named as R₁₅, R₁₁, R₇, and R₅) were collected from real landfill site. The ammonia nitrogen adsorption behaviors of MSW including equilibrium time, adsorption isotherms, and desorption behaviors including equilibrium time were determined. Furthermore, the effects of pH, OM, Cu(II), Zn(II), and Pb(II) on adsorption and desorption behavior of ammonia nitrogen were conducted by orthogonal experiment. The equilibrium time of ammonia nitrogen adsorption by each tested MSW was very short, i.e., 20 min, whereas desorption process needed 24 h and the ammonia nitrogen released from refuses was much lesser than that adsorbed, i.e., accounted for 3.20 % (R₁₅), 14.32 % (R₁₁), 20.59 % (R₇), and 20.50 % (R₅) of each adsorption quantity, respectively. The maximum adsorption capacity estimated from Langmuir isotherm appeared in R₁₅-KCl, i.e., 25,000 mg kg^?1. The best condition for ammonia nitrogen removal from leachate was pH >7.5, OM 23.58 %, Cu(II) <5 mg L^?1, Zn(II) <10 mg L^?1, and Pb(II) <1 mg L^?1. Ammonia nitrogen in landfill leachate could be quickly and largely absorbed by MSW but slowly and infrequently released. The refuse deposited for 15 years could be a suitable material for ammonia nitrogen removal.     

Removal of heavy metal ions from wastewater by a novel HEA/AMPS copolymer hydrogel: preparation, characterization, and mechanism

This study aims to synthesize 2-hydroxyethyl acrylate (HEA) and 2-acrylamido-2-methylpropane sulfonic (AMPS) acid-based hydrogels by gamma radiation and to investigate their swelling behavior and heavy metal ion adsorption capabilities. The copolymer hydrogels prepared were characterized via scanning electron microscopy, Fourier transformed infrared spectra, thermal gravimetric analysis, and X-ray photoelectron spectroscopy. The research showed that the copolymer hydrogel was beneficial for permeation due to its porous structure. In addition, the experimental group A-2-d [70 % water volume ratio and (n (AMPS)/n (HEA))?=?1:1] was an optimal adsorbent. The optimal pH was 6.0 and the optimal temperature was 15 °C. Pb²⁺, Cd²⁺, Cu²⁺, and Fe³+ achieved adsorption equilibriums within 24 h, whereas Cr³⁺ reached equilibrium in 5 h. Pb²+, Cd²⁺, Cr³⁺, and Fe³⁺ maximum load capacity was 1,000 mg L^?1, whereas the Cu²⁺ maximum capacity was 500 mg L^?1. The priority order in the multicomponent adsorption was Cr³⁺>Fe³⁺>Cu²⁺>Cd²⁺>Pb²⁺. The adsorption process of the HEA/AMPS copolymer hydrogel for the heavy metal ions was mainly due to chemisorption, and was only partly due to physisorption, according to the pseudo-second-order equation and Langmuir adsorption isotherm analyses. The HEA/AMPS copolymer hydrogel was confirmed to be an effective adsorbent for heavy metal ion adsorption.     

Removal mechanisms and kinetics of trace tetracycline by two types of activated sludge treating freshwater sewage and saline sewage

Understanding the removal mechanisms and kinetics of trace tetracycline by activated sludge is critical to both evaluation of tetracycline elimination in sewage treatment plants and risk assessment/management of tetracycline released to soil environment due to the application of biosolids as fertilizer. Adsorption is found to be the primary removal mechanism while biodegradation, volatilization, and hydrolysis can be ignored in this study. Adsorption kinetics was well described by pseudo-second-order model. Faster adsorption rate (k ₂?=?2.04?×?10^?2?g?min^?1?μg^?1) and greater adsorption capacity (q _e?=?38.8 μg?g^?1) were found in activated sludge treating freshwater sewage. Different adsorption rate and adsorption capacity resulted from chemical properties of sewage matrix rather than activated sludge surface characteristics. The decrease of tetracycline adsorption in saline sewage was mainly due to Mg²⁺ which significantly reduced adsorption distribution coefficient (K _d) from 12,990?±?260 to 4,690?±?180 L?kg^?1. Species-specific adsorption distribution coefficients followed the order of $ K_{\mathrm{d}}^{{ + 00}} \gg K_{\mathrm{d}}^{{ + - 0}} > K_{\mathrm{d}}^{{ + - - }} $ . Contribution of zwitterionic tetracycline to the overall adsorption was >90 % in the actual pH range in aeration tank. Adsorption of tetracycline in a wide range of temperature (10 to 35 °C) followed the Freundlich adsorption isotherm well.     

Emerging technology for increasing glucosinolates in arugula and mustard greens

Two plant species, arugula (Eruca sativa) and mustard (Brassica juncea) were field-grown under four soil management practices: soil mixed with municipal sewage sludge (SS), soil mixed with horse manure (HM), soil mixed with chicken manure (CM), and no-mulch bare soil (NM) to investigate the impact of soil amendments on the concentration of glucosinolates (GSLs) in their shoots. GSLs, hydrophilic plant secondary metabolites in arugula and mustard were extracted using boiling methanol and separated by adsorption on sephadex ion exchange disposable pipette tips filled with DEAE, a weak base, with a net positive charge that exchange anions such as GSLs. Quantification of GSLs was based on inactivation of arugula and mustard myrosinase and liberation of the glucose moiety from the GSLs molecule by addition of standardized myrosinase (thioglucosidase) and spectrophotometric quantification of the liberated glucose moiety. Overall, GSLs concentrations were significantly greater (1287 µg g^?1 fresh shoots) in plants grown in SS compared to 929, 890, and 981 µg g^?1 fresh shoots in plants grown in CM, HM, and NM soil, respectively. Results also revealed that mustard shoots contained greater concentrations of GSLs (974 µg g^?1 fresh shoots) compared to arugula (651 µg g^?1 fresh shoots).     

Comparative study of adsorption of Pb(II) on native garlic peel and mercerized garlic peel

A comparative study using native garlic peel and mercerized garlic peel as adsorbents for the removal of Pb²⁺ has been proposed. Under the optimized pH, contact time, and adsorbent dosage, the adsorption capacity of garlic peel after mercerization was increased 2.1 times and up to 109.05 mg g^?1. The equilibrium sorption data for both garlic peels fitted well with Langmuir adsorption isotherm, and the adsorbent–adsorbate kinetics followed pseudo-second-order model. These both garlic peels were characterized by elemental analysis, Fourier transform infrared spectrometry (FT-IR), and scanning electron microscopy, and the results indicated that mercerized garlic peel offers more little pores acted as adsorption sites than native garlic peel and has lower polymerization and crystalline and more accessible functional hydroxyl groups, which resulted in higher adsorption capacity than native garlic peel. The FT-IR and X-ray photoelectron spectroscopy analyses of both garlic peels before and after loaded with Pb²⁺ further illustrated that lead was adsorbed on the through chelation between Pb²⁺ and O atom existed on the surface of garlic peels. These results described above showed that garlic peel after mercerization can be a more attractive adsorbent due to its faster sorption uptake and higher capacity.     

Comprehending adsorption of methylethylketone and toluene and microwave regeneration effectiveness for beaded activated carbon derived from recycled waste bamboo tar

ABSTRACT

Beaded activated carbons (BACs) were derived from waste bamboo tar through carbonization (500°C for 2 hr) followed by physical activation using carbon dioxide (800–900°C for 2–4 hr). The adsorbent was examined for their physical and chemical properties, adsorption capacities toward methylethylketone (MEK) and toluene, and regenerabilities under microwave heating. It was found that the maximum total surface area reached for bamboo-tar-derived BAC after physical activation was 1364 m² g^?1, and more than 95% of the area was attributed to the microporous structures. Langmuir, Freundlich, and Dubinin-Radushkevich (D-R) isotherm models were applied to the adsorption isotherm fitting, and the minimum R² for each model was 0.986, 0.915, and 0.943, respectively. The isosteric heats of adsorption calculated based on D-R parameters for methylethylketone and toluene were 44.04 to 51.50 and 45.88 to 73.27 KJ mol^?1, respectively. They were slightly over the range of physisorption and increased with adsorbate loading, which might be related to the micropore filling mechanism. Microwave regeneration under 600 W of power output removed most of the adsorbate (>93.03%) within 8 min. The results of this study are intended to benefit future study on waste-derived adsorbent in environmental applications.     

Utilization of water chestnut for reclamation of water environment and control of cyanobacterial blooms

Overgrowth of water chestnut (Trapa spp.) is a regional problem throughout Asia and North America because of waterway blockage and water fouling upon decomposition. In the present study, we investigated the potential of water chestnut to control cyanobacterial blooms, via a high content of phenolic compounds. In addition, we assessed the impact of biomass harvesting and crude extract application on nutrient balance. We showed that the floating parts of water chestnut contained high concentrations of total phenolics (89.2 mg g^?1 dry weight) and exhibited strong antioxidant activity (1.31 mmol g^?1 dry weight). Methanol-extracted phenolics inhibited growth of Microcystis aeruginosa; the half maximal effective concentration (EC₅₀) of the extracted phenolics was 5.8 mg L^?1, which was obtained from only 103 mg L^?1 of dry biomass (the floating and submerged parts). However, the crude extracts also added important quantities of nitrogen, phosphorus, and potassium (1.49, 1.05, and 16.3 mg g^?1, respectively; extracted dry biomass weight basis); therefore, in practice, nutrient removal before and/or after the extraction is essential. On the other hand, biomass harvesting enables recovery of nitrogen, phosphorus, and potassium from the water environment (23.1, 2.9, and 18.7 mg g^?1, respectively; dry biomass weight basis). Our findings indicate that water chestnut contains high concentrations of phenolics and exhibits strong antioxidant activity. Utilization of these resources, including nutrients, will contribute to reclamation of the water environment, and also to disposal of wet biomass.     

Preparation of activated carbon from dried pods of Prosopis cineraria with zinc chloride activation for the removal of phenol

Utilization of agrowaste materials for the production of activated carbon, as an excellent adsorbent with large surface area, is well established industrially, for dephenolation of wastewater. In the present work, dried pods of Prosopis cineraria—a novel and low-cost agrowaste material—were used to prepare activated carbons by zinc chloride activation. Batch adsorption experiments were carried out to study the effects of various physicochemical parameters such as initial phenol concentration, adsorbent dose, initial solution pH, and temperature. Pseudo-first-order second-order and diffusion kinetic models were used to identify the possible mechanisms of such adsorption process. The Langmuir and Freundlich equations were used to analyze the adsorption equilibrium. Maximum removal efficiency of 86 % was obtained with 25 mg?L^?1 of initial phenol concentration. The favorable pH for maximum phenol adsorption was 4.0. Freundlich equation represented the adsorption equilibrium data more ideally than the Langmuir. The maximum adsorption capacity obtained was 78.32 mg?g^?1 at a temperature of 30 °C and 25 mg?L^?1 initial phenol concentration. The adsorption was spontaneous and endothermic. The pseudo-second-order model, an indication of chemisorption mechanism, fitted the experimental data better than the pseudo-first-order Lagergren model. Regeneration of spent activated carbon was carried out using Pseudomonas putida MTCC 2252 as the phenol-degrading microorganism. Maximum regeneration up to 57.5 % was recorded, when loaded phenol concentration was 25 mg?L^?1. The data obtained in this study would be useful in designing and fabricating an efficient treatment plant for phenol-rich effluents.     

Effects of silicon and copper on bamboo grown hydroponically

Due to its high growth rate and biomass production, bamboo has recently been proven to be useful in wastewater treatment. Bamboo accumulates high silicon (Si) levels in its tissues, which may improve its development and tolerance to metal toxicity. This study investigates the effect of Si supplementation on bamboo growth and copper (Cu) sensitivity. An 8-month hydroponic culture of bamboo Gigantocloa sp. “Malay Dwarf ” was performed. The bamboo plants were first submitted to a range of Si supplementation (0–1.5 mM). After 6 months, a potentially toxic Cu concentration of 1.5 μM Cu²⁺ was added. Contrary to many studies on other plants, bamboo growth did not depend on Si levels even though it absorbed Si up to 218 mg g^?1 in leaves. The absorption of Cu by bamboo plants was not altered by the Si supplementation; Cu accumulated mainly in roots (131 mg kg^?1), but was also found in leaves (16.6 mg kg^?1) and stems (9.8 mg kg^?1). Copper addition did not induce any toxicity symptoms. The different Cu and Si absorption mechanisms may partially explain why Si did not influence Cu repartition and concentration in bamboo. Given the high biomass and its absorption capacity, bamboo could potentially tolerate and accumulate high Cu concentrations making this plant useful for wastewater treatment.     

Examination of the influence of phenyltrimethylammonium chloride (PTMA) concentration on acetochlor adsorption by modified montmorillonite

The results presented in this paper show an impact of the concentration of the aromatic organic cation on the adsorption of acetochlor on the surface of the organic-modified montmorillonite. Natural montmorillonite from Bogovina (Boljevac municipality, Serbia) was used for organic modification in this experiment. Cation exchange capacity of this montmorillonite (86 mmol 100 g^?1 of clay) was determined using the methylene blue method. In pretreatment, montmorillonite was modified with NaCl. For the purpose of organic modification, three different concentrations of phenyltrimethylammonium chloride (PTMA) have been selected, based on calculated CEC value: 43 mmol 100 g^?1 of clay (0.5 CEC), 86 mmol 100 g^?1 of clay (1 CEC) and 129 mmol 100 g^?1 of clay (1.5 CEC). The changes in the properties of the inorganic and organic modified montmorillonite were examined using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and batch equilibrium method. Freundlich coefficients show higher uptake of the herbicide by montmorillonite modified with PTMA, compared to inorganic-modified montmorillonite. The results also indicate the influence of the organic cation concentration on the adsorption of the selected herbicide.     

Efficient removal of uranium(VI) from aqueous systems by heat-treated carbon microspheres

In this study, uranium(VI) was successfully removed from aqueous solutions using heat-treated carbon microspheres based on a batch adsorption technique. Influence of the parameters, such as solution pH, contact time, initial uranium(VI) concentration, and temperature on the removal efficiency have been investigated in detail. The results reveal that the maximum adsorption capacity of the heat-treated carbon microspheres toward uranium(VI) is 92.08 mg g^?1, displaying a high efficiency for the removal of uranium(VI) from aqueous solution. The experimental data are analyzed using sorption kinetic models. It is revealed that the process obey the pseudo-second-order kinetic model, the determining step might be chemical sorption. The thermodynamic parameters, such as ΔH°, ΔS°, and ΔG° show that the process is endothermic and spontaneous. This work provides an efficient, fast, and convenient approach for the removal of uranium(VI) from aqueous solutions.     

Synthesis of α-Fe2O3 nanofibers for applications in removal and recovery of Cr(VI) from wastewater

Purpose

Nanomaterials such as iron oxides and ferrites have been intensively investigated for water treatment and environmental remediation applications. The purpose of this work is to synthesize α-Fe₂O₃ nanofibers for potential applications in removal and recovery of noxious Cr(VI) from wastewater.

Methods

α-Fe₂O₃ nanofibers were synthesized via a simple hydrothermal route followed by calcination. The crystallographic structure and the morphology of the as-prepared α-Fe₂O₃ nanofibers were characterized by X-ray diffraction, scanning electron microscope, and transmission electron microscope. Batch adsorption experiments were conducted, and Fourier transform infrared spectra were recorded before and after adsorption to investigate the Cr(VI) removal performance and adsorption mechanism. Langmuir and Freundlich modes were employed to analyze the adsorption behavior of Cr(VI) on the α-Fe₂O₃ nanofibers.

Results

Very thin and porous α-Fe₂O₃ nanofibers have been successfully synthesized for investigation of Cr(VI) removal capability from synthetic wastewater. Batch experiments revealed that the as-prepared α-Fe₂O₃ nanofibers exhibited excellent Cr(VI) removal performance with a maximum adsorption capacity of 16.17 mg g^?1. Furthermore, the adsorption capacity almost kept unchanged after recycling and reusing. The Cr(VI) adsorption process was found to follow the pseudo-second-order kinetics model, and the corresponding thermodynamic parameters ΔG°, ΔH°, and ΔS° at 298 K were calculated to be ?26.60 kJ?mol^?1, ?3.32 kJ?mol^?1, and 78.12 J?mol^?1 K^?1, respectively.

Conclusions

The as-prepared α-Fe₂O₃ nanofibers can be utilized as efficient low-cost nano-absorbents for removal and recovery of Cr(VI) from wastewater.     

Adsorption characteristics of Cu(II) from aqueous solution onto biochar derived from swine manure

The purpose of this study was to investigate adsorption characteristic of swine manure biochars pyrolyzed at 400 °C and 700 °C for the removal of Cu(II) ions from aqueous solutions. The biochars were characterized using BET surface area, Fourier transform infrared spectroscopy (FTIR), zeta potential, scanning electron microscopy/energy dispersive spectrometer (SEM–EDS), and X-ray diffraction (XRD). The adsorption of Cu(II) ions by batch method was carried out and the optimum conditions were investigated. The adsorption processes of these biochars are well described by a pseudo-second-order kinetic model, and the adsorption isotherm closely fitted the Sips model. Thermodynamic analysis suggested that the adsorption was endothermic. The maximum Cu(II) adsorption capacities of biochars derived from fresh and composted swine manure at 400 °C were 17.71 and 21.94 mg g^?1, respectively, which were higher than those at 700 °C. XRD patterns indicated that the silicate and phosphate particles within the biochars served as adsorption sites for Cu(II). The removal of Cu(II) ions from industrial effluent indicated that the fresh swine manure biochar pyrolyzed at 400 °C can be considered as an effective adsorbent.     

Novel chitosan/PVA/zerovalent iron biopolymeric nanofibers with enhanced arsenic removal applications

Enhanced removal application of both forms of inorganic arsenic from arsenic-contaminated aquifers at near-neutral pH was studied using a novel electrospun chitosan/PVA/zerovalent iron (CPZ) nanofibrous mat. CPZ was carefully examined using scanning electron microscopy (SEM) equipped with energy-dispersive X-ray analysis (EDX), transmission electron microscopy (TEM), atomic fluorescence spectroscopy (AFM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), and thermal gravimetric analysis (TGA). Application of the adsorbent towards the removal of total inorganic arsenic in batch mode has also been studied. A suitable mechanism for the adsorption has also been discussed. CPZ nanofibers mat was found capable to remove 200.0?±?10.0 mg g^?1 of As(V) and 142.9?±?7.2 mg g^?1 of As(III) from aqueous solution of pH 7.0 at ambient condition. Addition of ethylenediaminetetraacetic acid (EDTA) enabled the stability of iron in zerovalent state (ZVI). Enhanced capacity of the fibrous mat could be attributed to the high surface area of the fibers, presence of ZVI, and presence of functional groups such as amino, carboxyl, and hydroxyl groups of the chitosan and EDTA. Both Langmuir and Freundlich adsorption isotherms were applicable to describe the removal process. The possible mechanism of adsorption has been explained in terms of electrostatic attraction between the protonated amino groups of chitosan/arsenate ions and oxidation of arsenite to arsenate by Fentons generated from ZVI and subsequent complexation of the arsenate with the oxidized iron. These CPZ nanofibrous mats has been prepared with environmentally benign naturally occurring biodegradable biopolymer chitosan, which offers unique advantage in the removal of arsenic from contaminated groundwater.