共存物质对重金属絮凝剂MCC除镉性能的影响

为进一步拓展天然高分子絮凝剂壳聚糖的应用范围,以壳聚糖、L-半胱氨酸为原料,通过酰胺化反应制备一种具有重金属捕集功能的高分子重金属絮凝剂-2-氨基-3-巯基丙酰壳聚糖(MCC),研究了水体中常见的阴阳离子、有机配位剂及浊度对MCC除镉性能的影响,探讨了絮体形貌与絮体分形维数及絮凝除镉效果间的关系。结果表明,Na+、Cl-、NO-3、F-、SO2-4的存在对MCC除Cd2+均有促进作用,Ca2+表现为明显的抑制作用;低浓度的EDTA对除镉有促进作用,随着EDTA浓度的增大,逐渐转为抑制作用;低浓度的腐殖酸对MCC去除Cd2+有显著的促进作用;在一定范围内,浊度可促进MCC对Cd2+的去除;絮体间空隙越多,絮体分形维数越小,除镉效果越好。     

共存物质对重金属絮凝剂 MCC 除镉性能的影响简

为进一步拓展天然高分子絮凝剂壳聚糖的应用范围，以壳聚糖、L-半胱氨酸为原料，通过酰胺化反应制备一种具有重金属捕集功能的高分子重金属絮凝剂-2-氨基-3-巯基丙酰壳聚糖（MCC），研究了水体中常见的阴阳离子、有机配位剂及浊度对MCC除镉性能的影响，探讨了絮体形貌与絮体分形维数及絮凝除镉效果间的关系。结果表明，Na⁺、Cl^-、NO₃^-、F^-、SO₄^2-的存在对MCC除Cd²⁺均有促进作用，Ca²⁺表现为明显的抑制作用；低浓度的EDTA对除镉有促进作用，随着EDTA浓度的增大，逐渐转为抑制作用；低浓度的腐殖酸对MCC去除Cd²⁺有显著的促进作用；在一定范围内，浊度可促进 MCC对Cd²⁺的去除；絮体间空隙越多，絮体分形维数越小，除镉效果越好。     

高分子重金属絮凝剂MCC制备及除铜去浊性能

以壳聚糖、L-半胱氨酸为原料,通过酰胺化反应制备了一种具有重金属捕集功能的高分子重金属絮凝剂-2-氨基-3-巯基丙酰壳聚糖(MCC)。以含铜废水为处理对象,通过正交实验研究了MCC的最佳制备条件,对其除铜性能进行了全面探讨,并对絮体形貌进行了观察和分析。结果表明,在最佳条件下制得的MCC具有除浊和捕集重金属离子双重功能,形成的絮体量较大、沉速快,出水水质好,重金属回收率较高,残渣稳定,不易造成二次污染,絮体分形维数越小,空隙越多,除铜效果越好。     

絮凝形态学研究及进展

从水体中原始颗粒、絮凝剂和絮体3个方面综述了絮凝形态学的研究进展，尤其是分形理论在絮凝理论与工程中的应用。絮体是具有自相似或自仿射和标度不变的分形结构，其分形维数是描述絮凝过程的重要因素。絮体分形结构导致了絮体碰撞的作用半径、有效密度等变化，从而对颗粒物分离过程有重要的影响。     

壳聚糖改性红壤去除铜绿微囊藻

研究了聚合氯化铝铁和壳聚糖改性对高岭土、海泡石和红壤去除水中铜绿微囊藻效果的影响。结果表明,壳聚糖改性的红壤对铜绿微囊藻的去除效果最好,其生成絮体密实度大,抗扰动能力强。当改性红壤的投加量为50 mg/L时,叶绿素a和铜绿微囊藻去除率分别达到98.0%、95.1%。该絮凝剂适应性好,在pH为3.0~6.0的范围内对铜绿微囊藻均可取得很好的去除效果,对叶绿素a和浊度的去除率可达90%以上。壳聚糖通过包裹红壤颗粒,借助壳聚糖的粘结架桥和电中和能力,大幅度提高了红壤的絮凝性能。该絮凝剂处理富藻水,具有絮凝效果明显、絮体密实度大、投加量少、绿色环保、经济等优点,在工程上具有较大的实用价值。     

臭氧气浮工艺絮体尺度与界面理化特性调控

针对臭氧气浮工艺对有机物脱色和去除性能的限制,通过阴、阳离子型聚丙烯酰胺(ployacrylamide,PAM)对以腐殖酸为代表的天然有机物絮体的尺度调控,采用气载絮体尺度、二维分形维数及絮体与微气泡间的接触角对PAM浓度梯度下形成的气载絮体进行了表征;研究了阴阳离子型PAM浓度梯度对腐殖酸的降解效果和气载絮体尺度;并探讨了阴阳离子型PAM、絮体与微气泡间的结合机理。结果表明:PAM的投加提高了臭氧气浮工艺中腐殖酸的去除性能,且气载絮体尺寸、分形维数和接触角均有所增大;在不同类型PAM中均存在最佳PAM剂量,在此剂量下,体系内去除效果、气载絮体大小和接触角最大、分形维数最小;在最佳PAM剂量下,与阴离子型PAM相比,阳离子型PAM形成气载絮体的大小和接触角较大,分形维数较小,且去除效果较好。在臭氧气浮体系中,通过改善PAM、絮体与微气泡结合静电作用力的强弱形成了利于气浮的气载絮体尺度,提高了对腐殖酸的去除效果。     

壳聚糖衍生物的合成及其絮凝性能的研究

对从虾蟹壳中制备的壳聚糖进行改性，分别制得壳聚糖衍生物——壳聚糖季铵盐和羧甲基壳聚糖，用于味精废水的絮凝实验。实验结果表明，壳聚糖、壳聚糖季铵盐和羧甲基壳聚糖作为絮凝剂处理味精废水均有较好的效果，以壳聚糖季铵盐的效果最好，其pH值适用范围宽、絮体沉降快，是一种具有良好反应活性的高分子絮凝剂。     

巯基化条件对巯基乙酰壳聚糖除镉性能的影响

为有效处理含镉废水,同时进一步拓展天然高分子絮凝剂壳聚糖(CTS)的应用范围,通过正交实验得到了一种可用于除镉的高分子絮凝剂——巯基乙酰壳聚糖(MAC)的最佳制备条件。实验结果表明,在该条件下得到的MAC对废水中镉的去除率最高可达99.96%,水中镉的残余量为0.01 mg/L,远低于我国废水排放标准(0.1 mg/L);同时巯基乙酰壳聚糖与壳聚糖相比水溶性大大增强,可溶于pH值11以下的废水。     

絮凝形态学研究及进展

从水体中原始颗粒、絮凝剂和絮体 3个方面综述了絮凝形态学的研究进展 ,尤其是分形理论在絮凝理论与工程中的应用。絮体是具有自相似或自仿射和标度不变的分形结构 ,其分形维数是描述絮凝过程的重要因素。絮体分形结构导致了絮体碰撞的作用半径、有效密度等变化 ,从而对颗粒物分离过程有重要的影响。     

混凝-气浮控制三卤甲烷生成势的研究

研究了混凝一气浮工艺对不同分子量区间三卤甲烷生成势（trihalomethanes formation potential，THMFP）的去除效果及絮体形态对THMFP去除效果的影响。结果表明，混凝一气浮工艺以去除大分子量区间THMFP为主，对小分子量区间THMFP的去除效果较差。UV254值与THMFP值的线性相关系数为0．9449，UV254值可以较好地反映THMFP的含量。絮体的分形维数为1．17～1．2时，孔隙率较大，可增加絮体对THMFP的活性吸附空间，且絮体相对密度较小，可增强同向絮凝作用，增加絮体和THMFP的接触概率，有利于气浮对THMFP的去除。     

巯基酯化壳聚糖的合成及对Cd2＋的去除性能研究

采用化学方法，研究了以巯基甲壳质制备巯基酯化壳聚糖的最佳合成方案。研究表明，巯基甲壳质的脱乙酰条件（包括时间、温度、氢氧化钠浓度）影响其产物巯基酯化壳聚糖对重金属镉离子的吸附效果。当脱乙酰时间为2h，温度为160℃，氢氧化钠浓度为20％时，20mg的合成产物对30mLCd2＋浓度为20mg／L水样的去除率最高，达到85．46％，其对镉离子的吸附量达到28．5mg／g。通过对产物进行红外分析发现，巯基甲壳质中出现脂基特征峰值，脱乙酰后脂基并没有消失，证明最后的产物为巯基酯化壳聚糖。     

一种新型环境矿物材料在废水治理中的应用研究--硅质磷块岩吸附水溶液中镉离子的研究

硅质磷块岩对水溶液中镉离子的吸附实验结果表明,硅质磷块岩对水溶性镉离子具有良好的去除效果,主要影响因素有介质的酸度、作用时间、镉离子的初始浓度和样品用量.在pH=6,作用时间为15 min,初始Cd2+浓度为30mg/L的实验条件下,硅质磷块岩对镉离子的去除率可达98%,有可能利用动态法进行工业废水的连续处理.初步研究结果显示,磷块岩对水溶性镉离子的吸附作用符合Langmuir等温吸附模型,不同产地的硅质磷块岩S1和S2对镉离子的最大吸附容量分别为4.43 mg/g和3.88 mg/g.     

Copper and cadmium removal from synthetic industrial wastewater using chitosan and nylon 6

Purpose

Chitosan with nylon 6 membranes was evaluated as adsorbents to remove copper and cadmium ions from synthetic industrial wastewater.

Methods

Chitosan and nylon 6 with glutaraldehyde blend ratio with (1:1+Glu, 1:2+Glu, and 2:1+Glu) have been prepared and these were used as membranes to remove copper and cadmium ions from synthetic industrial wastewater. Characterization of the synthesized membrane has been done with FTIR, XRD, TGA/DTA, DSC, and SEM. Chemical parameters for quantities of adsorption of heavy metal contamination have been done and the kinetics of adsorption has also been carried out.

Results

The optimal pH for the removal of Cd(II) and Cu(II) using chitosan with nylon 6. Maximum removal of the metals was observed at pH 5 for both the metals. The effect of adsorbent dose also has a pronounced effect on the percentage of removal of the metals. Maximum removal of both the metals was observed at 5 g/100 ml of the adsorbent.

Conclusion

Copper and cadmium recovery is parallel at all time. The percentage of removal of copper increased with increase in the pH from 3 to 5. In the case of cadmium containing wastewater, the maximum removal of metal occurred at pH 5. The uptake amount of Cu²⁺ ions on chitosan increased rapidly with increasing contact time from 0 to 360 min and then reaches equilibrium after 360 min; the equilibrium constant for copper and cadmium ions is more or less the same for the adsorption reaction.     

Polyelectrolyte enhanced ultrafiltration (PEUF) for the removal of Cd(II): effects of organic ligands and solution pH

This study focused on the effects of pH and organic ligands, namely ethylenediaminetetraacetic acid (EDTA), nitrilotriacetic acid (NTA), and citric acids, on the removal and recovery of Cd(II) in polyelectrolyte enhanced ultrafiltration (PEUF). Polyethylenimine (PEI), which can bind with both positively charged metal ions by coordination bonding and negatively charged ligand-metal complexes by charge attraction, was employed as a chelating polymer. The removal and recovery of Cd species was greatly dependent on the chemistry of organic ligands according to solution pH, particularly being related to the distribution of Cd-ligand complexes at different pH levels. In the presence of EDTA, the dominant Cd species are negatively charged Cd(EDTA)(2-) and CdH(EDTA)(-) over the range of pH levels investigated, interacting with PEI via electrostatic attraction and being less pH dependent. On the other hand, the pH effects of both NTA and citric acid systems are similar to that for the system without organic ligands. This was associated with the fact that free Cd ions were predominant at the acidic pH range in both NTA and citric acid systems.     

浮游球衣菌对Pb2+、Cu2+、Zn2+、Cd2+的吸附性能研究

研究了浮游球衣菌（Sphaerotilus natans）在不同吸附条件下对溶液中Pb^2＋、Cu^2＋、Zn^2＋、Cd^2＋的吸附规律。结果表明,Sphaerotilus natans对这4种重金属离子均有一定的吸附作用,并在20min内达到吸附平衡,pH对吸附过程影响较大,pH为5.5时Sphaerotilus natans对这4种金属离子的吸附效果最好,Sphaerotilus natans对它们的吸附选择性为Pb^2＋〉Cu^2＋〉Zn^2＋〉Cd^2＋,Pb^2＋、Cu^2＋能部分置换出已被菌体吸附的Zn^2＋、Cd^2＋。HCI和EDTA溶液可有效地将金属离子从菌体上解吸下来,解吸后的菌体可重复使用。     

Influence of clay on the adsorption of heavy metals like copper and cadmium on chitosan

The influence of clay on the adsorption of heavy metals like copper and cadmium on chitosan from simulated industrial wastewater is evaluated. Chitosan–clay blend with ratio of (1:1), (1:2), and (2:1) have been prepared, and these were used as membranes to remove copper and cadmium ions from synthetic industrial wastewater. The chemical parameters for quantities of adsorption of heavy metal contamination have been done, and the kinetics of adsorption has also been carried out. Clay provides enough absorbable sites to overcome mass transfer limitations. The number of absorbable sites for cadmium is more compared to copper, and thus the rate of recovery of cadmium is faster than copper, and the percentage removal of cadmium is more than copper at all times on clay over nylon 6. This difference indicates the influence of clay in the adsorption of heavy metals in comparison to synthetic polymer nylon 6. Rate constant for first-order kinetics of adsorption, k ₁, for copper and cadmium is less than that of clay, which clearly indicates that clay, which is a natural polymer, is more kinetically favored compared to synthetic polymer. The difference in the intraparticle diffusion in both the natural and synthetic polymer is not much, and it suggests that the particle diffusion mechanism is the same in both cases. Copper and cadmium recovery is parallel at all times. The percentage of removal of copper increased with an increase in pH from 3 to 5. In the case of cadmium containing wastewater, the maximum removal of metal occurred at pH 5. The uptake amount of Cu²⁺ ions on chitosan increased rapidly with increasing the contact time from 0 to 360 min and then reaches equilibrium after 360 min, and the equilibrium constant for copper and cadmium ions are more or less the same for the adsorption reaction. There are more adsorption sites for cadmium in the presence of clay and mass transfer limitation is avoided without resorting to rotation, which is the highlight of the present work. And more so, this is pronounced in the case of natural polymer compared to synthetic polymer.     

一株抗Cd~（2＋）菌株的筛选及其吸附性能

Cd2＋为一种毒性金属元素,为了实际解决污水中低浓度重金属污染,实现污水达标排放,通过12C6＋重离子束辐照诱变技术筛选到一株耐受Cd2＋的菌株C2,研究其对Cd2＋的抗性和低浓度Cd2＋的吸附性能表明,Cd2＋浓度≤100 mg/L时,C2菌株可以生长繁殖,但随Cd2＋浓度升高受到抑制;SEM分析表明,受到Cd2＋胁迫时,C2产生大量胞外产物与Cd2＋形成络合物;吸附过程中菌粉表面空隙得到填充,形成凸起;红外光谱分析表明,吸附过程中的主要作用基团为醇羟基O—H键、氨基和酰胺基团;C2菌粉和固定化菌球都对Cd2＋有较好的吸附能力,菌粉吸附效果比固定化菌球稍好;菌粉和固定化吸附剂的最佳吸附初始pH值为5~6.0,最佳投加量分别为1.0 g/L和10 g/L（实际含菌量为1.0 g/L）;Cd2＋浓度在2~20mg/L时,在最佳吸附条件下,菌粉和固定化吸附剂对Cd2＋的吸附率均在90%左右;2种吸附剂吸附过程与Langmuir等温模型和拟二级动力学模型拟合最佳;热力学研究表明吸附反应均能自发进行。以上研究结果表明,C2菌粉和固定化吸附剂均可用于污水中低浓度Cd2＋的去除。     

EDTA-enhanced extraction of heavy metals from a coarse grained simulated soil by the CEHIXM process

The effect of ethylenediaminetetraacetic acid (EDTA) in extracting heavy metal contaminants, namely Pb, Cd, Zn, and Mn, from soils with organometallic complexes, was explored using the coupled electric-hydraulic gradient assisted by ion exchange medium (CEHIXM) decontamination process. The experiments were conducted with a constant electric voltage of 50 DC V and a constant hydraulic flow rate of 4 cm3/min. The results obtained from the experiments demonstrated that EDTA was effective in extracting Pb, Cd, Zn, and Mn from soils in which acidic pH did not produce significant dissolution. Metal removal as high as 99% was achieved with 0.05 M EDTA solution within 200 hr.