乙醇胺/N-甲基二乙醇胺/三乙烯四胺体系吸收烟气CO_2的研究

在乙醇胺(MEA)/N-甲基二乙醇胺(MDEA)体系(简称二元复合胺体系)中加入少量活化剂三乙烯四胺(TETA),研究了MEA/MDEA/TETA三元复合胺体系(简称三元复合胺体系)对烟气CO2的吸收和再生情况。结果表明,MEA、MDEA、TETA3种组分之间存在交互作用,使得三元复合胺体系中的CO2吸收速率、CO2饱和吸收量均分别小于二元复合胺体系与TETA单体系的CO2吸收速率、CO2饱和吸收量之和。三元复合胺体系的再生温度稍高于二元复合胺体系,其一次再生率约为83.5%,比二元复合胺体系低了约13百分点,三元复合胺体系的再生较二元复合胺体系更困难。     

醇胺溶液吸收与解吸CO2的研究

在温度333K、常压条件下,在羟乙基乙二胺(AEE)总量一定的溶液中,研究了不同浓度AEE对CO2的吸收性能;在总胺质量分数为40%的溶液中,研究了不同配比的AEE N-甲基二乙醇胺(MDEA)对CO2的吸收性能.考察了吸收过程中吸收速率、吸收量、吸收时间、AEE浓度以及吸收液温度的相互关系.控制解吸过程温度为393K,考察了CO2解吸量与解吸时间的关系.实验表明,适当降低AEE浓度有利于充分发挥AEE溶液的CO2吸收性能;在MDEA溶液中加入适量AEE,可以明显提高CO2的吸收与解吸性能;其中质量分数为20?E 20%MDEA的复合溶液在CO2吸收与解吸过程中表现出良好的实际操作性.     

混合胺MEA＋DETA吸收CO2的影响因素

以MEA为主体，DETA为添加剂，考察1h内，在温度298～338K，压力300～700kPa，混合胺溶液初始浓度（质量分数）4％～20％范围内，MEA＋DETA不同配比的混合吸收剂吸收CO2的特性。获得MEA＋DETA混合胺吸收CO2的最佳吸收条件为：308K、500kPa、总胺质量浓度为20％，MEA与DETA的配比为8：2。     

N-甲基二乙醇胺/哌嗪/羟乙基乙二胺三元复合溶液捕集烟气中CO2中试研究

化学吸收法是目前烟气回收CO2技术的研究热点,其中一类重要的吸收剂就是醇胺复合溶液.醇胺复合溶液具有对CO2吸收速率快、吸收容量大及再生简单的特点,成为烟气CO2吸收剂的首选.采用中试连续实验装置,以N-甲基二乙醇胺(MDEA)/哌嗪(PZ)/羟乙基乙二胺(AEEA)(摩尔比为0.70:0.15:0.15)三元复合溶液为吸收剂对烟气中CO2进行吸收处理.研究结果表明,吸收剂最佳摩尔浓度为3.0 mol/L,最佳吸收温度为40℃,最佳液气比为10 L/m3；再沸器的热负荷随着吸收温度、吸收剂浓度以及液气比的增加而增大,脱碳率随着入口烟气中CO2浓度的增加而降低.     

混合胺MEA+DETA吸收CO2的影响因素

以MEA为主体,DETA 为添加剂,考察1 h内,在温度298~338 K,压力300~700 kPa,混合胺溶液初始浓度(质量分数)4%~20%范围内,MEA+DETA不同配比的混合吸收剂吸收CO₂的特性。获得MEA+DETA混合胺吸收CO₂的最佳吸收条件为:308 K、500 kPa、总胺质量浓度为20%,MEA与DETA 的配比为8:2。     

4种脂肪多胺修饰硅胶对铅离子的吸附

为了合成高效铅离子吸附剂,了解其对铅离子的吸附规律。采用(3-氯丙基)三甲氧基硅烷(CPTS)架桥法,以硅胶(SG)为载体,乙二胺(EDA)、二乙烯三胺(DETA)、三乙烯四胺(TETA)和四乙烯五胺(TEPA)为表面修饰剂,合成了4种胺化硅胶,测定了它们的红外光谱、热重等性质以及对Cu2+、Zn2+和Pb2+的吸附能力。结果表明,4种胺化硅胶对Pb2+的吸附量均大于Cu2+和Zn2+的吸附量,其中DETA修饰硅胶对Pb2+的吸附量较高。4种胺化硅胶对Pb2+的吸附过程较好地符合拟二级动力学模型以及Langmuir和Scatchart等温吸附热力学模型,其对Pb2+吸附的速率常数、饱和吸附量以及吸附位点数由大到小的顺序一致,均为SG-DETASG-TEPASG-EDASG-TETA。4种胺化硅胶对Pb2+的吸附速率和吸附量呈现"奇数胺"增强效应,亲和常数则依次减小。阐明了脂肪多胺修饰硅胶对Pb2+的吸附规律,并进一步讨论了Scatchart和Langmuir热力学模型的统一性。     

TEPA/TETA改性SBA-15对CO_2吸附性能的影响

以非离子表面活性剂P123作为模板剂,正硅酸乙酯为硅源,加入扩孔剂合成SBA-15介孔材料。以三乙烯四胺(TETA)和四乙烯五胺(TEPA)作为改性剂,对所得材料分别进行质量百分比20%、30%、35%和40%的负载量改性,得到CO2的吸附材料。用热重法测定材料的CO2吸附脱附性能,氮气物理吸附-脱附和元素分析法对样品进行表征。结果表明,同样负载条件下,TEPA改性效果显著优于TETA改性,这是由于TEPA比TETA多出一个胺基;在4个附载量中,30%~35%的负载量最优,其中35%TEPA负载量的扩孔SBA-15(SBA-15k)的CO2吸附量最高,达2.86 mmol/g;循环吸附脱附的结果表明经过5次吸附脱附,材料的吸附性能没有明显变化;吸附平衡时间很短,不到10 min,有利于实际应用;氮气物理吸附-脱附和元素分析结果表明,改性剂很好地负载到SBA-15k样品上,SBA-15k对TEPA和TETA的负载改性起到促进作用。     

CO2捕集回收技术研究

主要介绍了常用的胺化合物吸收法、钙基吸收剂法、金属氧化物法等CO2捕集回收技术的最新研究进展及存在的问题,综合对比了各种方法的优缺点:胺化合物吸收法吸收速率快,但再生能耗较高,因此开发"高效低耗"的复合吸收剂成为研究的重点;钙基吸收剂法在高温环境下对CO2的吸收有较好的效果,但吸收剂的碳酸化转化率及热稳定性是有待解决的关键问题;金属氧化物法具有高的CO2吸收效率,但成本较高.在此基础上,探索了CO2捕集回收技术改进工艺,提出改善吸收剂性能、开发高效低耗的CO2选择性吸收剂将成为今后CO2捕集回收技术的研究方向.     

填料塔中的DBU溶液吸收CO_2

在自制的1,8-二氮杂双环[5,4,0]十一碳-7-烯(DBU)吸收CO2的填料塔中,研究DBU溶液浓度、入口CO2浓度、DBU溶液流量、气体流量、气体温度以及填料层高度对CO2吸收的影响。结果表明,DBU溶液浓度从1.5%增加到25%,CO2吸收容量和吸收效率均逐步减小;入口CO2浓度从4.5%增加到15%,CO2吸收容量和吸收效率均逐渐增大;DBU溶液流量从20 m L/min增加到120 m L/min,CO2吸收容量和吸收效率略有增加;气体流量从0.7 L/min增加到3.3 L/min,填料层高度从5 cm增加到45 cm,CO2吸收容量和吸收效率均呈先增后减趋势;气体温度从25℃增加到60℃,CO2吸收容量和吸收效率略有下降。DBU溶液在填料塔内能够高效吸收气体中的CO2。     

多循环CCRs法在分离燃煤锅炉尾部烟气中CO2方面的应用

随着温室效应和全球变暖的加剧,煤燃烧所排出的CO2作为引起温室效应的主要气体而引起人们的密切关注.由于燃煤锅炉所排放的尾气中所含的CO2的体积份额低、排放量大,而且处于微负压状态,因此目前控制和分离吸收CO2的方法,包括各类吸收法、吸附法、膜分离法和O2/CO2燃烧技术等,能够经济可行地适用于电力工业燃煤锅炉尾部烟气中CO2分离的方法非常少.与上述各类方法相比,钙基吸收剂CCRs(calcination/carbonation reactions)法是一种新兴的经济可行的分离燃煤锅炉尾部烟气中CO2的方法.对采用该法时,吸收剂的选择、吸收剂在多次CCRs过程中结构特点的变化、提高吸收剂对CO2的吸收容量以及防止吸收剂反应性的衰减等方面进行了详细的阐述.     

Aerobic biodegradability of methyldiethanolamine (MDEA) used in natural gas sweetening plants in batch tests and continuous flow experiments

Mixtures of different amines including tertiary amines (methyldiethanolamine, MDEA) are commonly used for the removal of CO₂ from gas mixtures or in gas sweetening processes for the extraction of CO₂ and H₂S. The absorber solutions used can be released into the industrial waste water due to continuous substitution of degraded MDEA, periodically cleaning processes or an accidental spill. In this study, the aerobic biodegradability of MDEA was investigated in a standardised batch test and a continuous flow experiment (40 l/d). The results of the batch test indicated that the MDEA-solution was non-biodegradable during the test period of 28 days, whereas the continuous flow experiments showed biodegradation of more than 96% based on TOC-measurements. This was probably due to the adaptation of the microorganisms to this particular waste water contamination during continuous flow experiment.     

膜基活化溶液中活化剂在回收温室气体CO2过程中的作用

将AMP和PZ作为活化剂添加于MDEA溶液中，形成活化溶液，研究了膜基活化溶液回收温室气体CO₂性能，着重考察活化剂的活化作用和对膜接触器传质加强的影响，提出一个活化机理来解释活化现象，建立了阻力层方程模型, 并模拟膜基活化溶液回收CO₂的传质过程。结果表明，活化剂对膜接触器传质的加强起到重要作用，具有双氨基环状结构的PZ对传质的加强作用高于具有空间位阻结构的AMP；活化溶液的CO2回收率和传质通量明显高于未活化的MDEA溶液，活化性能PZ＞AMP；活化剂的活化效应与分子结构有关；流体力学的改变对传质的影响有限，活化剂的反应动力学对传质的加强起主导作用；阻力层方程模型能较好地模拟膜基活化溶液回收CO₂传质过程，传质通量和总传质系数的模型值与实验值符合较好。     

Effect of pH on the aggregation of a gray humic acid in colloidal and solid states

The potential of triethylenetetramine (TETA) to inhibit the oxidation of three pyrrhotites, Garson, McCreedy and Po-97 has been studied systematically and confirmed by comparing the release of Fe and SO4(2-) from samples with and without coating treatment. Each sample, original or coated by TETA, was exposed to oxygen, 1 x 10(-3) M FeCl3, and Acidithiobacillus ferrooxidans, respectively, for specific oxidation periods. Both abiotic and biotic oxidation of samples treated by this passivating agent has been reduced significantly in this study. Under the aerobic condition, lower concentrations of ferric, total Fe or SO4(2-) were obtained from the coated samples than those from the uncoated samples. In the presence of 1 x 10(-3) M FeCl3 at 30 degrees C, TETA was able to reduce oxidation rates of Garson, McCreedy and Po-97 by 83%, 79%, and 81% (based on Fe release), respectively. A higher pH, lower Eh, and lower concentrations of total Fe and SO4(2-) were also observed in the biotic oxidation of coated Garson by Acidithiobacillus ferrooxidans. The protection of pyrrhotite surface from oxidant attack by TETA barrier and the alkaline property of this coating agent can be used to interpret the inhibition of oxidation.     

The effect of triethylene tetramine upon the selective removal of nickel (II), iron (II), manganese (II) and tin (II) in rats

The distribution of Nickel-63, Iron-59, Manganese-54 and Tin-113 in plasma was studied in rats which received single intravenous (i.v.) injection of aqueous solutions of their salts alone, and in rats which also received single intramuscular (im) injection of triethylene tetramine (TETA). TETA was extremely effective in reducing the plasma concentration of Nickel-63 followed by that of Iron-59, Manganese-54 and Tin-113.     

旋转填充床吸收模拟工业废气中SO2的研究

选择3%SO2作为模拟工业废气,一乙醇胺（MEA）作为吸收剂在超重力条件下对模拟工业废气中脱硫工艺进行了实验研究,考察了旋转填充床转速、气液比、吸收剂入口温度以及吸收剂浓度对脱硫率的影响,确定了MEA作为吸收剂时适宜的操作条件。同时在旋转填充床中考察了几种不同吸收剂对3%SO2脱除率的影响。研究表明,1 mol/L哌嗪（PZ）的脱除率最优,1 mol/L N-甲基乙醇胺（MDEA）的脱除率最低。     

旋转填充床吸收模拟工业废气中SO2的研究

选择3%SO2作为模拟工业废气,一乙醇胺(MEA)作为吸收剂在超重力条件下对模拟工业废气中脱硫工艺进行了实验研究,考察了旋转填充床转速、气液比、吸收剂入口温度以及吸收剂浓度对脱硫率的影响,确定了MEA作为吸收剂时适宜的操作条件.同时在旋转填充床中考察了几种不同吸收剂对3%SO2脱除率的影响.研究表明,1 mol/L哌嗪...     

Absorption and reaction kinetics of amines and ammonia solutions with carbon dioxide in flue gas

The removal system for the absorption of CO2 with amines and NH3 is an advanced air pollution control device to reduce greenhouse gas emissions. Absorption of CO2 by amines and NH3 solutions was performed in this study to derive the reaction kinetics. The absorption of CO2 as encountered in flue gases into aqueous solutions of monoethanolamine (MEA), diethanolamine (DEA), and NH3 was carried out using a stirred vessel with a plane gas-liquid interface at 50 degrees C. Various operating parameters were tested to determine the effect of these variables on the absorption kinetics of the reactants in both gas and liquid phases and the effect of competitions between various reactants on the mass-transfer rate. The observed absorption rate increases with increasing gas-liquid concentration, solvent concentration, temperature, and gas flow rate, but changes with the O2 concentration and pH value. The absorption efficiency of MEA is better than that of NH3 and DEA, but the absorption capacity of NH3 is the best. The active energies of the MEA and NH3 with CO2 are 33.19 and 40.09 kJ/mol, respectively.