Catalytic oxidation processes for removing dimethylsulfoxide from wastewater

An effective method for removing dimethylsulfoxide (DMSO) from wastewater, based on the mild selective catalytic sulfoxidation with H(2)O(2), is proposed in this study. The catalysts are W-containing layered double hydroxides (LDH), and they were obtained by ionic exchange of the nitrate anions from MAl-LDH precursors (M=Mg(2+) or Zn(2+)) with both WO(4)(2-) and W(7)O(24)(6-) species. Results of X-ray diffraction (XRD), N(2) adsorption, thermal gravimetric analysis (TGA), diffuse reflectance ultraviolet spectroscopy (DRUV) and Raman spectroscopy confirmed the formation of the W-oxospecies inside the interlayer space and the modification of the textural properties upon the exchange process. All catalysts showed very good activity and stability in the DMSO conversion into dimethylsulfone with dilute H(2)O(2) aqueous solution, at low temperatures (20-50 degrees C). The efficiency of the H(2)O(2) was higher than 95% and the behaviour of the water as solvent was very close to that of the organic solvents (ethanol, acetonitrile, 1,4-dioxane).     

Pentachlorophenol association with fulvic acids from recycled wastes

The apparent water solubility of pentachlorophenol was measured at pH=6 and at 25 degrees C in pure water, aqueous solutions of three salts (NaCl, KNO(3) and CaCl(2) at 0.010, 0.10 and 1.0M) and in aqueous solutions of three fulvic acids samples extracted from a natural soil (sFA), composted sewage sludge (csFA) and composted livestock's material (lsFA). A solubility enhancement method was developed for the measurement of partition coefficients (K(oc), L/kg organic carbon). Pentachlorophenol associates strongly with the fulvic acid samples and the calculated K(oc) were the following (averages and standard deviations): (sFA) (211+/-22) x 10(2), (csFA) (253+/-26) x 10(2), (lsFA) (235+/-10) x 10(2). For comparison purposes the K(oc) for pyrene were also calculated for the three FA samples and were the following: (sFA) (119+/-10) x 10(2), (csFA) (239+/-21) x 10(2), (lsFA) (92+/-10) x 10(2). The analysis of variance (one-way ANOVA) of the effect of the type of FA sample on the solubilization of pentachlorophenol and pyrene shows that this factor causes significant differences on the aqueous solubilization of these two organic substances.     

Volatile organic profiles and photochemical potentials from motorcycle engine exhaust

This study surveyed emissions from 2- and 4-stroke new and in-use motorcycles. Emission tests were carried out on a dynamometer following the designated test procedure of the Economic Commission for Europe (ECE). Samples were derived during various driving stages, which included idle, acceleration, 30 km/hr cruise, 50 km/hr cruise, and deceleration. All test motorcycles (10 new and 15 in-use) complied with Taiwan Environmental Protection Administration's Phase III Motorcycle Emission Standards. The dominant volatile organic carbon (VOC) species were isopentane (53 and 295 mg/km, 2- and 4-stroke, respectively), 2-methylpentane (75 and 83 mg/km), 3-methylpentane (34 and 66 mg/km), and toluene (30 and 100 mg/km). The VOC emission factors for the 2-/4-stroke motorcycles were 311/344 (new) and 1479/433 (in-use) mg/km, respectively. In addition, the dominant carbonyl species for the new and in-use motorcycles were formaldehyde (0.4 and 0.7 mg/km, respectively), acetaldehyde (0.6 and 1.2 mg/km), and acetone (0.5 and 0.7 mg/km). The carbonyl compound emission factors for the 2- and 4-stroke motorcycles were 3.2/3.1 (new) and 5.3/4.6 (in-use) mg/km, respectively. The ozone formation potentials, based on an ECE test cycle, show that the values from the in-use motorcycles were higher than those from the new motorcycles. The dominant VOC species for the ozone formation potential were propylene (65 and 502 mg-O3/km, respectively), isopentane (98 and 501 mg-O3/km), 2-methylpentane (152 and 167 mg-O3/ km), 3-methylpentane (79 and 253 mg-O3/km), and toluene (127 and 398 mg-O3/km). Further, the dominant carbonyl species were formaldehyde (4.1 and 6.2 mg-O3/ km, new and in-use, respectively) and acetaldehyde (4.8 and 9 mg-O3/km).     

Cadmium in soil solutions from a transect of soils away from a fertiliser bin

The effects of high inputs of phosphate fertiliser on Cd concentrations were studied in soil solutions extracted from topsoils. Soils were sampled along a transect at distances of 1-100 m away from a fertiliser bin. The transect was sampled four times during 1 year. Soil solutions were analysed for Cd, pH, major cations and anions, and other heavy metals (As, Cr, Cu, Pb). For one of the transect samplings, soil total Cd, Cr, Cu, Pb and P were also measured. Cd speciation in the soil solutions was calculated by the GEO-CHEM-PC computer program. Chemical composition varied substantially along the transect, and also between samplings, indicative of seasonal effects and the influence of a fresh application of superphosphate fertiliser during the year. Application of fertiliser decreased soil solution pH and increased the levels of heavy metals in soil solution. Generally, soil total Cd, Cr, Cu, Pb, and P decreased with increasing distance from the fertiliser bin. Correlations between P and the four heavy metals were: P and Cd (R2 = 0.978), P and Cr (R2 = 0.712), P and Pb (R2 = 0.538), P and Cu (R2 = 0.267). Less than 1% of the total Cd in the soil samples was found in the soil solution. The free metal ion Cd2+ accounted for 55-90% of solution Cd. Of the complexed species of Cd, the chloride and sulphate complexes were usually the most important, even when nitrate and phosphate concentrations were relatively high. The presence of As, Cr, Cu and Pb had no effect on Cd speciation.     

Abatement of sulfur hexafluoride emissions from the semiconductor manufacturing process by atmospheric-pressure plasmas

Sulfur hexafluoride (SF6) is an important gas for plasma etching processes in the semiconductor industry. SF6 intensely absorbs infrared radiation and, consequently, aggravates global warming. This study investigates SF6 abatement by nonthermal plasma technologies under atmospheric pressure. Two kinds of nonthermal plasma processes--dielectric barrier discharge (DBD) and combined plasma catalysis (CPC)--were employed and evaluated. Experimental results indicated that as much as 91% of SF6 was removed with DBDs at 20 kV of applied voltage and 150 Hz of discharge frequency for the gas stream containing 300 ppm SF6, 12% oxygen (O2), and 40% argon (Ar), with nitrogen (N2) as the carrier gas. Four additives, including Ar, O2, ethylene (C2H4), and H2O(g), are effective in enhancing SF6 abatement in the range of conditions studied. DBD achieves a higher SF6 removal efficiency than does CPC at the same operation condition. But CPC achieves a higher electrical energy utilization compared with DBD. However, poisoning of catalysts by sulfur (S)-containing species needs further investigation. SF6 is mainly converted to SOF2, SO2F4, sulfur dioxide (SO2), oxygen difluoride (OF2), and fluoride (F2). They do not cause global warming and can be captured by either wet scrubbing or adsorption. This study indicates that DBD and CPC are feasible control technologies for reducing SF6 emissions.     

Emissions from India's transport sector: Statewise synthesis

A decentralized emission inventories are prepared for road transport sector of India in order to design and implement suitable technologies and policies for appropriate mitigation measures. Globalization and liberalization policies of the government in 90's have increased the number of road vehicles nearly 92.6% from 1980–1981 to 2003–2004. These vehicles mainly consume non-renewable fossil fuels, and are a major contributor of green house gases, particularly CO₂ emission. This paper focuses on the statewise road transport emissions (CO₂, CH₄, CO, NO_x, N₂O, SO₂, PM and HC), using region specific mass emission factors for each type of vehicles. The country level emissions (CO₂, CH₄, CO, NO_x, N₂O, SO₂ and NMVOC) are calculated for railways, shipping and airway, based on fuel types. In India, transport sector emits an estimated 258.10 Tg of CO₂, of which 94.5% was contributed by road transport (2003–2004). Among all the states and Union Territories, Maharashtra's contribution is the largest, 28.85 Tg (11.8%) of CO₂, followed by Tamil Nadu 26.41 Tg (10.8%), Gujarat 23.31 Tg (9.6%), Uttar Pradesh 17.42 Tg (7.1%), Rajasthan 15.17 Tg (6.22%) and, Karnataka 15.09 Tg (6.19%). These six states account for 51.8% of the CO₂ emissions from road transport.     

Emission of NOx from urine-treated pasture

Emission of NO(x) from urine-treated pasture was determined using a system of enclosures coupled to a chemiluminescence NO(x) analyser. Rates of emission ranged from 0 to 190 microg NO(x) - Nm(-2)h(-1), with a mean of 43 microg N m(-2) h(-1). The lowest rates were associated with periods of heavy or persistent rain. On average, NO comprised 68% of the NO(x) produced. Emissions of NO(x) were apparently associated with the nitrification of ammonium N derived from hydrolysis of organic N constituents in the urine applied. Emissions from untreated pasture occurred at a mean rate of 1.7 microg NO(x) -N m(-2) h(-1). NO(x) comprised only a small proportion (<0.1%) of the emission of other nitrogenous gases (NH(3), N(2) and N(2)O) following application of urine. The mean rate of NO(x) emission suggested a total release to the atmosphere of 2.3 x 10(-8) g N year(-1) from urine returned to pasture in the UK. This loss is not significant in agronomic terms and is equivalent to only 0.04% of the estimated anthropogenic emissions for the UK.     

Production of hydrogen-rich gas from methane by thermal plasma reform

This study investigated the reforming characteristics and optimum operating condition of the high-temperature plasma torch (so called plasmatron) for hydrogen-rich gas (syngas) production. At the optimum condition, the composition of produced syngas was 45.4% hydrogen (H2), 6.9% carbon monoxide (CO), 1.5% carbon dioxide (CO2), and 1.1% acetylene (C2H2). The H2/CO ratio was 6.6, hydrogen yield was 78.8%, and the energy conversion rate was 63.6%. To obtain the optimum operating condition, parametric studies were carried out examining the effects of O2/CH4 ratio, steam/CH4 ratio, and Ni catalyst addition in reactor. When the steam/CH4 ratio was 1.23, the production of hydrogen was maximized and the methane conversion rate was 99.7%. The syngas composition was determined to be 50.4% H2, 5.7% CO, 13.8% CO2, and 1.1% C2H2. The H2/CO ratio was 9.7, hydrogen yield was 93.7%, and the energy conversion rate was 78.8%. Hydrogen production with catalyst was effective, compared with no catalyst.     

SynGas production from organic waste using non-thermal-pulsed discharge

The purpose of this study was to develop a technology that can convert biogas to synthesis gas (SynGas), a low-emission substituted energy, using a non-thermal-pulsed plasma method. To investigate the characteristics of SynGas production from simulated biogas, the reforming characteristics in relation to variations in pulse frequency, biogas component ratio (C3H8/CO2), vapor flow ratio (H2O/total flow rate [TFR]), biogas velocity, and pulse power were studied. A maximum conversion rate of 49.1% was achieved for the biogas when the above parameters were 500 Hz, 1.5, 0.52, 0.32 m/sec, and 657 W, respectively. Under the above conditions, the dry basis mole fractions of the SynGas were as follows: H2 = 0.645, CH4 = 0.081, C2H2 = 0.067, C3H6 = 0.049, CO = 0.008 and C2H4 = 0.004. The ratio of hydrogen to the other intermediates in the SynGas (H2/ITMs) was 3.1.     

The utilization of catalyst sorbent in scrubbing acid gases from incineration flue gas

Catalyst sorbents based on alumina-supported CuO, CeO2, and CuO-CeO2 were applied to a dry scrubber to clean up the SO2/HCl/NO simultaneously from pilot-scale fluidized-bed incineration flue gas. In the presence of organic compounds, CO and the submicron particles SO2 and HCI removed by the fresh catalyst sorbents and NO reduced to N2 by NH3 under the catalysis of fresh and spent desulfurization/dechloridization (DeSO2/DeHCl) catalyst sorbents (copper compounds, Cu, CuO, and CuSO4) were evaluated in this paper. The fresh and spent catalyst sorbents were characterized by the Brunner-Emmett-Teller method (BET), X-ray powder diffraction (XRPD), scanning electron microscopy (SEM), inductively coupled plasma-mass spectrometry (ICP-MS), and the elemental analyzer (EA). The study showed that the performances of CuO, CeO2, and CuO-CeO2/gamma-Al2O3 were better than that of Ca(OH)2. The removal efficiency of SO2 and HCl was 80-95% in the dry scrubber system. Under NH3/NO = 1, NO could not be reduced to N2 because it was difficult to control the ratio of air/fuel in the flue gas. For estimating the feasibility of regenerating the spent catalyst sorbents, BET and EA analyses were used. They indicated that the pore structures were nearly maintained and a small amount of carbon accumulated on their surface.     

聚环氧琥珀酸萃取锰泥残渣中铬的研究

聚环氧琥珀酸(PESA)是一种具有无磷及非氮结构、环境友好型水溶性聚合物,且具有螯合多价金属阳离子的性能和可生物降解性的特征,选取其作为锰泥残渣中铬的螯合萃取剂,研究了不同pH、螯合萃取剂剂量、搅拌时间下PESA对铬的萃取率。结果表明:(1)最佳萃取条件为pH=4、PESA剂量30mg/g、搅拌时间60min;在最佳萃取条件下,铬的萃取率可达95%。(2)从结构上看,PESA是由醚基和羧基基团组成的高分子聚合物,羧基基团是与金属离子作用的主要官能团,它对Ca2+、Mg2+、Zn2+、Cr(Ⅲ)、Cr(Ⅵ)和Pb2+等有较强的螯合能力;从溶液的配位角度看,PESA与金属有较强的结合能力。因此,PESA对锰泥残渣中的铬有萃取作用。     

Iron improving bio-char derived from microalgae on removal of tetracycline from aqueous system

Novel magnetic carbonaceous bio-char was hydrothermal prepared from microalgae under different loadings of iron and its structures and surface chemistry were characterized with Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and nitrogen adsorption-desorption isotherm (BET). The morphology of bio-char changed from sheet to particle as iron loading increased and its surface area also increased. When 3.0 g of dried microalgae and 6.0 mmol iron salt ((NH₄)₂SO₄·FeSO₄·6H₂O) were mixed and treated, the obtained bio-char possessing the highest amount of oxygen-containing functional groups resulted in the best adsorption performance on tetracycline (TC). This adsorption process was fitted to Langmuir adsorption isotherm and the maximum adsorption capacity was 95.86 mg/g, which is higher than other bio-char reported. The iron loading contributed to the higher adsorption capacity of bio-char, which may be due to three factors, the high surface area, more hydrogen bonding, and bridging effects of the structural Fe for TC. Our data suggest that bio-char may have more important role in stabilization of pollutants in the environment.     

Occurrence of alternative flame retardants in indoor dust from New Zealand: indoor sources and human exposure assessment

Due to worldwide restrictions on polybrominated diphenyl ethers (PBDEs), the demand for alternative flame retardants (AFRs), such as organophosphate flame retardants (OPFRs), novel brominated FRs (NBFRs) and hexabromocyclododecanes (HBCDs), has recently increased. Little is known about human exposure to NBFRs and OPFRs and that their levels in dust have been scarcely evaluated worldwide. To increase the knowledge regarding these chemicals, we measured concentrations of five major NBFRs, ten OPFRs and three HBCD isomers in indoor dust from New Zealand homes. Dust samples were taken from living room floors (n=34) and from mattresses of the same houses (n=16). Concentrations (ngg(-1)) of NBFRs were: 1,2-bis(2,4,6-tribromophenoxy)ethane (BTBPE) (<2-175), decabromodiphenyl ethane (DBDPE) (<5-1430), 2-ethylhexyl-2,3,4,5-tetrabromobenzoate (TBB) (<2-2285) and bis(2-ethylhexyl)-3,4,5,6-tetrabromophthalate (TBPH) (<2-640). For OPFRs, concentrations (ngg(-1)) ranged between: tri-ethyl-phosphate (TEP) (<10-235), tri-n-butyl-phosphate (TnBP) (<20-7545), tris-(2-chloroethyl)-phosphate (TCEP) (<20-7605), tris-(1-chloro-2-propyl) phosphate (TCPP) (20-7615), tri-(2-butoxyethyl)-phosphate (TBEP) (50-27325), tris-(2,3-dichloropropyl)-phosphate (TDCPP) (20-16560), tri-phenyl-phosphate (TPhP) (20-35190), and tri-cresyl-phosphate (TCP) (<50-3760). HBCD concentrations fell in the range <2-4100ngg(-1). BTBPE, DBDPE, TBPH, TBEP, and TnBP showed significant positive correlation (p<0.05) between their concentrations in mattresses and the corresponding floor dust (n=16). These data were used to derive a range of plausible exposure scenarios. Although the estimated exposure is well below the corresponding reference doses (RfDs), caution is needed given the likely future increase in use of these FRs and the currently unknown contribution to human exposure by other pathways such as inhalation and diet.     

Preliminary data from the USEPA dry deposition network: 1989

The objective of the National Dry Deposition Network is to determine patterns and trends of dry deposition for various sulfur and nitrogen species at roughly 50 locations throughout the continental USA. Each site is equipped for collection of continuous meteorological and ozone data and weekly average concentrations of SO4(2-), NO3-, SO2 and HNO3, using a three-stage filter pack. Results from 40 eastern US sites operational throughout 1989 show species-dependent variability from site to site, season to season, and day to night. Annual average concentrations of atmospheric SO4(2-), NO3-, SO2 and HNO3 ranged from 2.7 to 7.9, 0.2 to 3.9, 2.4 to 23.2 and 0.7 to 3.6 microg/m(-3), respectively. Seasonal variability was considerable for all constituents. Day/night data indicate that SO2 and HNO3, but not SO4(2-) and NO3-, are typically found at moderately to substantially lower concentrations at night, especially during spring and summer. Estimated dry deposition for SO2 and HNO3 appear to be much greater than for SO4(2-) and NO3-, respectively. Comparison of measured wet deposition and estimated dry deposition at numerous sites suggests that the two are similar in magnitude over much of the eastern USA.     

Mobility of atrazine from alginate-bentonite controlled release formulations in layered soil

The mobility of atrazine [6-chloro-N2-ethyl-N4-isopropyl-1,3,5-triazine-2,4-diamine] from alginate-bentonite-based controlled release (CR) formulations was investigated by using soil columns. Two CR formulations based on sodium alginate (14.0 g kg(-1), atrazine (6.0 g kg(-1), natural or acid-treated bentonite (50 g kg(-1), and water (924 g kg(-1) were compared to technical grade product and commercial liquid (CL) formulation (Gesaprim 500FW). All herbicide treatments were applied to duplicate layered bed systems simulating the typical arrangement under a plastic greenhouse, which is composed of sand (10 cm), peat (2 cm), amended soil (20 cm) and native soil (20 cm). The columns were leached with 39 cm (1500 ml) and 156 cm (6000 ml) of 0.02 M CaCl2 solution to evaluate the effect of water volume applied on herbicide movement. When 39 cm of 0.02 M CaCl2 solution was applied, there was no presence of herbicide in the leachate for the alginate-bentonite CR treatments. However, 0.11% and 0.14% of atrazine appeared in the leachate when the treatment was carried out with technical grade and CL formulations, respectively. When 156 cm of 0.02 M CaCl2 solution was applied, the use of the alginate-acid treated bentonite CR formulation retards and reduces the presence of atrazine in the leachate as compared to technical product. Analysis of the soil columns showed the highest atrazine concentration in the peat layer. Alginate-bentonite CR formulations might be an efficient system for reducing atrazine leaching in layered soil and thus, it could reduce the risks of pollution of groundwater.     

Methane and carbon dioxide emissions from closed landfill in Taiwan

The atmospheric concentrations and emission rates of CH(4) and CO(2) were studied at three sites of the Fu-Der-Kan closed landfill and after as the multi-use recreational park in northern Taiwan. Atmospheric CH(4) and CO(2) concentrations of closed landfill were 1.7-4.6 and 324-409ppm, respectively. CH(4) and CO(2) emission rates ranged from 8.8 to 163mg m(-2)h(-1) and from 495 to 1531mg m(-2)h(-1), respectively. Diurnal variation was noted with higher values at night than those in daytime. After creation of the park, atmospheric CH(4) and CO(2) concentrations were 1.8-3.1 and 332-441ppm, respectively. CH(4) and CO(2) emission rates ranged from -1.1 to 2.3mg m(-2)h(-1) and from -135 to 301mg m(-2)h(-1), respectively. There were no notable diurnal variations in either atmospheric concentrations or emission rates.     

Selenium extractability from a contaminated fine soil fraction: implication on soil cleanup

Two batches of fine soil fraction of an acidic soil were deliberately contaminated with selenite (Se(IV)) and selenate (Se(VI)), respectively, and aged for more than 220 days. Speciation analysis using continuous flow-through hydride generation atomic absorption spectrometry (HGAAS) indicated that the species were predominant in their respective aged soils. A selective sequential extraction scheme was employed to fractionate the Se retained in the soils into six fractions of varying retentions. Abilities of various chemical reagents in extracting the Se in the two soil batches were then evaluated. The reagents investigated were sodium salts such as sodium chloride (NaCl), sodium sulfate (Na2SO4), sodium carbonate (Na2CO3), and sodium phosphate (Na3PO4), and two oxidants, namely, hydrogen peroxide (H2O2) and potassium permanganate (KMnO4). It was found that NaCl, Na2SO4, and Na2CO3 could only extract the exchangeable fraction of Se, while Na3PO4 could extract the exchangeable and strongly-bound fractions. Selenate was extracted more than Se(IV) by the salts. The kinetics of Se(IV) extraction by Na3PO4 could be best described by the Elovich model, while the Ritchie second-order model was the most appropriate to describe Se(VI) extraction. Efficiencies of the oxidants in Se(IV) extraction highly depended on their applied dosages. Both H2O2 and KMnO4 were able to extract greater than 93% of total Se, and therefore were significantly more effective than the salts in Se(IV) extraction.     

The role of metals in dioxin formation from combustion of newspapers and polyvinyl chloride in an incinerator

Newspapers impregnated with NaCl mixed with various chloride metals (CuCl2, MgCl2, MnCl2, FeCl3, NiCl2, and CoCl2) and electric wire coated with polyvinyl chloride (PVC) were combusted in a well-controlled incinerator. Exhaust gas samples collected at the outlet of the incinerator were analyzed for dioxins (PCDDs, PCDFs, and coplanar PCBs) by gas chromatography/mass spectrometry. The amount of total dioxins formed from newspaper samples ranged from 34.2 ng/g (with NaCl+CoCl2) to 67.0 ng/g (with NaCl+CuCl2). PCDFs composed 88-94% of the total dioxins formed in the exhaust gases. The highest levels of PCDF isomers obtained were Cl3-CDF from the sample with NaCl+CuCl2 (14.8 ng/g), Cl2-CDF from the sample with NaCl+MgCl2 (12.3 ng/g), and Cl(1)-CDF from samples with NaCl+MnCl2 (12.6 ng/g), with NaCl+FeCl3 (11.8 ng/g), and with NaCl+NiCl2 (13.3 ng/g), and with NaCl+CoCl2 (8.62 ng/g). The total of Cl4-8-CDDs comprised 76-88% of the total Cl1-8-CDDs. In particular, Cl7-CDDs had the highest levels except for the sample with NaCl+NiCl2. Total dioxins formed from samples of electric wire coated with PVC and PVC alone were 38.3 ng/g and 112 ng/g, respectively, suggesting that the presence of copper reduced dioxin formation.     

Rat urinary metabolites from O,O-diethyl-O-(3,5,6-trichloro-2-pyridyl) phosphorothioate.

Rats metabolized single oral doses of O,O-diethyl-O(3,5,6-trichloro-2-pyridyl-2,6-14C) phosphorothioate to at least six radiolabeled urinary metabolites. The urine contained about 90 percent of the dose. Three of these metabolites were identified as the glucuronide of 3,5,6-trichloro-2-pyridinol (80% the urinary 14C), a glycoside of 3,5,6-trichloro-2-pyridinol (4%), and 3,5,6-trichloro-2-pyridinol (12%).     

Halogen production from aqueous tropospheric particles

Box model studies have been performed to study the role of aqueous phase chemistry with regard to halogen activation for marine and urban clouds and the marine aerosol as well. Different chemical pathways leading to halogen activation in diluted cloud droplets and highly concentrated sea salt aerosol particles are investigated. The concentration of halides in cloud droplets is significantly smaller than in sea-salt particles, and hence different reaction sequences control the overall chemical conversions. In diluted droplets radical chemistry involving OH, NO(3), Cl/Cl(2)(-)/ClOH(-), and Br/Br(2)(-)/BrOH(-) gains in importance and pH independent pathways lead to the release of halogens from the particle phase whereas the chemistry in aerosol particles with high electrolyte concentrations is controlled by non-radical reactions at high ionic strengths and relatively low pH values.For the simulation of halogen activation in tropospheric clouds and aqueous aerosol particles in different environments a halogen module was developed including both gas and aqueous phase processes of halogen containing species. This module is coupled to a base mechanism consisting of RACM (Regional Atmospheric Chemistry Mechanism) and the Chemical Aqueous Phase Radical Mechanism CAPRAM 2.4 (MODAC-mechanism). Phase exchange is described by the resistance model by Chemistry of Multiphase Atmospheric Systems, NATO ASI Series, 1986.It can be shown that under cloud conditions the bromine atom is mainly produced by OH initiated reactions, i.e. its concentration maximum is reached at noon. In contrast, the concentration level of chlorine atoms is linked to NO(3) radical chemistry leading to a smaller amplitude between day and night time concentrations.The contribution of radical processes to halogen atom formation in the particle phase is evident, e.g. by halogen atoms which undergo direct phase transfer. Furthermore, the application of the multiphase model for initial concentrations for sea-salt aerosols shows that the particle phase can act as a main source of halogen containing molecules (Cl(2), BrCl, Br(2)) which are photolysed in the gas phase to yield halogen atoms (about 70% of all Cl sources and more than 99% for Br).