4种高级氧化法处理高浓度正丙醇废水的动力学比较

研究了1%和10%(V/V)模拟正丙醇废水在UV/TiO2体系、UV/H2O2体系、Fe2+/H2O2体系和UV/TiO2/Fe2+/H2O2体系等4种工艺条件下的降解动力学过程,对比了降解动力学特点及工艺参数对动力学常数的影响,优化工艺参数。结果表明,UV/TiO2体系和Fe2+/H2O2体系的降解过程可分为零级反应阶段和一级反应阶段,转折点分别在反应开始后2 h和氧化剂浓度为6.7 g/L,UV/H2O2体系和UV/TiO2/Fe2+/H2O2体系分别符合零级反应和一级反应规律;相同工艺参数条件下,6 h反应后,组合工艺UV/TiO2/Fe2+/H2O2体系在处理效率达85%,比前3个体系分别高52.0%、8.3%和32.0%,与UV/TiO2体系和Fe2+/H2O2体系的处理效率之和持平,其协同效应提高了速率常数,在目标物浓度降低时依然可维持较高降解速率。而目标物浓度提高10倍后,UV能量利用率提高35.5倍,氧化剂用量是Fe2+/H2O2体系的1/7.1。     

Comparison of the degradation of p-hydroxybenzoic acid in aqueous solution by several oxidation processes

A comparative study is made of 12 methods of chemical oxidation applied to degrading p-hydroxybenzoic acid in aqueous solution. The oxidation processes tested were: UV, O3, UV/TiO2, O3/Fe2+, O3/H2O2, O3/UV, UV/H2O2, H2O2/Fe2+, H2O2/Fe2+/O3, UV/H2O2/O3, H2O2/Fe2+/UV and O3/UV/H2O2/Fe2+. The 12 processes were ranked by reactivity. In a kinetic study, the overall kinetic rate constant was split up into three components: direct oxidation by UV irradiation (photolysis), direct oxidation by ozone (ozonation), and oxidation by free radicals (mainly OH*).     

Suppression of estrogenic activity of 17-beta-estradiol by beta-cyclodextrin

The suppressive effects of cyclodextrins (CDs) on the strong estrogenic activity of 17β-estradiol (E2) in water environments were investigated in this study. Cyclodextrins are doughnut-shaped molecules that possess a hydrophobic cavity and a hydrophilic exterior. The cavity can incorporate nonpolar molecules as guests to form inclusion complexes. β-CD and 2-hydroxypropyl-β-CD (HP-β-CD) were the most successful in forming a complex with E2 and improving its low aqueous solubility. The E2/CDs complexes bound to the estrogen receptor in a cell-free system as determined by ELISA and suppressed the hormone activities as measured by a yeast two-hybrid assay. These results indicate that hydrophobic E2 is easily transported through the lipid zone of the plasma membrane into the target cell and can bind to the nuclear receptor. However, the hydrophilic E2/β-CD and E2/HP-β-CD complexes do not penetrate the membrane. Therefore, these CDs are able to suppress the hormone activity of E2 through complex formation.     

超声波-光催化氧化降解邻氯苯酚的研究

对超声波一光催化氧化降解邻氯苯酚(2-cp)进行了研究．探讨了溶液初始pH、TiO2投加量、H2O2投加量和溶液初始浓度对2-cp降解率的影响。并对几种不同处理方法降解2-cp的结果进行了对比。结果表明，超声波和紫外光的协同效果明显，在相同的反应时间内，超声波能够明显提高光催化降解2-cp的降解率。超声波和紫外光连用，具有良好的工业应用前景。     

SO2的气相光催化氧化及催化剂的失活和再生研究

在模拟大气环境中,紫外光照射以及纳米TiO2光催化剂的作用下,气相无机污染物SO2被完全氧化为SO3或H2SO4。本文提出了SO2的非均相光催化氧化机理,并得出光催化反应速率符合一级动力学过程;经过连续使用之后,TiO2的光催化活性降低,最后活性消失;经过水洗之后,失活的TiO2可以得到再生。失活的TiO2和新鲜的TiO2的IR和XPS光谱差异表明,失活的TiO2表面存在H2SO4,其被认为是使催化剂失活的成分。     

Partitioning of hydrogen peroxide between the gas and liquid phases in the presence of surfactant

Gas-liquid phase partitioning is a key physical property that can predict the environmental fate of a compound between two phases. Several environmental factors have been known to affect the gas-liquid phase partitioning. We investigated the influence of surfactant on the gas-liquid phase partitioning of hydrogen peroxide (H(2)O(2)). The surfactant used was ammonium perfluorooctanoate (APFO). H(2)O(2) solution containing the surfactant was equilibrated in a closed system and gas phase H(2)O(2) concentration was measured by the peroxyoxalate chemiluminescence (PO-CL) method. Gas phase H(2)O(2) concentrations remained constant below the critical micelle concentration (CMC) and increased linearly with surfactant concentration above the CMC, which indicated that surfactant micelles influenced the gas-liquid phase partitioning of H(2)O(2). This result showed that H(2)O(2)-micelle interactions are less favorable than H(2)O(2)-H(2)O interactions. Surfactant monomers did not affect the gas-liquid phase partitioning of H(2)O(2) due to the absence of micelles. Solvent (methanol) effect was also investigated and showed that gas phase H(2)O(2) concentrations increased with the addition of solvent. This indicated the unfavorable interaction of H(2)O(2) with hydrophobic medium compared to hydrophilic one. It is consistent with the result that H(2)O(2)-micelles has a weaker interaction than H(2)O(2)-water because surfactant micelles are hydrocarbon-like organic phase rather than aqueous phase.     

Comparison of advanced oxidation processes and identification of monuron photodegradation products in aqueous solution

The photodegradation of monuron (3-(4-chlorophenyl)-1,1-dimethylurea) in aqueous solutions under simulated solar irradiation has been conducted by different advanced oxidation processes (UV/H(2)O(2), UV/H(2)O(2)/Fe(2+), UV/H(2)O(2)/TiO(2), UV/TiO(2), dark H(2)O(2)/Fe(3+)). The degradation rates were always higher for the homogeneous catalysis in photo-Fenton reactions (UV/H(2)O(2)/Fe(2+)) compared to the heterogeneous photocatalytic systems (TiO(2)/UV and UV/H(2)O(2)/TiO(2)). Optimal concentrations of Fe(2+) and H(2)O(2) for the abatement of the herbicide in the photo-Fenton system were found to be 1 mM Fe(II) and 10 mM H(2)O(2). Several intermediary products were identified using large volume injection micro-liquid chromatography with UV detection (mu-LC-UV), mu-LC-MS and GC-MS techniques and a degradation mechanism has been proposed.     

Photo-oxidation of cork manufacturing wastewater

Several photo-activated processes have been investigated for oxidation of a cork manufacturing wastewater. A comparative activity study is made between different homogeneous (H2O2/UV-Vis and H2O2/Fe2+/UV-Vis) and heterogeneous (TiO2/UV-Vis and TiO2/H2O2/UV-Vis) systems, with degradation performances being evaluated in terms of total organic carbon (TOC) removal. Results obtained in a batch photo-reactor show that photo-catalysis with TiO2 is not suitable for this kind of wastewater while the H2O2/UV-Vis oxidation process, for which the effect of some operating conditions was investigated, allows to remove 39% of TOC after 4 h of operation (for C(H2O2)=0.59 M, pH=10 and T=35 degrees C). The combined photo-activated process, i.e., using both TiO2 and H2O2, yields an overall TOC decrease of 46% (for C(TiO2)=1.0 gl(-1)). The photo-Fenton process proved to be the most efficient, proceeds at a much higher oxidation rate and allows to achieve 66% mineralization in just 10 min of reaction time (for C(H2O2)=0.31 M, T=30 degrees C, Fe2+:H2O2=0.12 (mol) and pH=3.2).     

Predictions of binary sorption isotherms for the sorption of heavy metals by pine bark using single isotherm data

The adsorption of three heavy metal ions by pine bark was studied. The study was divided into two parts; single component adsorption of the metals Cu2+, Cd2+ and Ni2+ and bisolute adsorption of the three binary systems Cu2+-Cd2+, Cu2+-Ni2+ and Cd2+-Ni2+. Extended Langmuir model, extended Freundlich model. Sips model and ideal adsorption solution theory (IAST) models were used to predict the equilibrium uptake for Cu2+, Cd2+ and Ni2+ in the binary diluted solutions using the single adsorption constants. The experimental data of single isotherm adsorption process were found to follow Langmuir isotherm model with less accuracy than Freundlich and Sips models. Whereas, the predictions of bisolute adsorption isotherms of the mentioned three systems, Cu2+-Cd2+, Cu2+-Ni2+ and Cd2+-Ni2+, showed good agreement with experimental data when using Extended-Langmuir, Extended-Freundlich and IAST. However, the only good fit of the Sips model was with the Cu2+-Cd2+ system.     

Effect of void structure of photocatalyst paper on VOC decomposition

TiO₂ powder-containing paper composites, called TiO₂ paper, were prepared by a papermaking technique, and their photocatalytic efficiency was investigated. The TiO₂ paper has a porous structure originating from the layered pulp fiber network, with TiO₂ powders scattered on the fiber matrix. Under UV irradiation, the TiO₂ paper decomposed gaseous acetaldehyde more effectively than powdery TiO₂ and a pulp/TiO₂ mixture not in paper form. Scanning electron microscopy and mercury intrusion analysis revealed that the TiO₂ paper had characteristic unique voids ca. 10 μm in diameter, which might have contributed to the improved photocatalytic performance. TiO₂ paper composites having different void structures were prepared by using beaten pulp fibers with different degrees of freeness and/or ceramic fibers. The photodecomposition efficiency was affected by the void structure of the photocatalyst paper, and the initial degradation rate of acetaldehyde increased with an increase in the total pore volume of TiO₂ paper. The paper voids presumably provided suitable conditions for TiO₂ catalysis, resulting in higher photocatalytic performance by TiO₂ paper than by TiO₂ powder and a pulp/TiO₂ mixture not in paper form.     

Toxic effects of low concentrations of Cu on nodulation of cowpea (Vigna unguiculata)

Although Cu is phytotoxic at Cu(2+) activities as low as 1-2 microM, the effect of Cu(2+) on the nodulation of legumes has received little attention. The effect of Cu(2+) on nodulation of cowpea (Vigna unguiculata (L.) Walp. cv. Caloona) was examined in a dilute solution culture system utilising a cation exchange resin to buffer solution Cu(2+). The nodulation process was more sensitive to increasing Cu(2+) activities than both shoot and root growth; whilst a Cu(2+) activity of 1.0 microM corresponded to a 10% reduction in the relative yield of the shoots and roots, a Cu(2+) activity of 0.2 microM corresponded to a 10% reduction in nodulation. This reduction in nodulation with increasing Cu(2+) activity was associated with an inhibition of root hair formation in treatments containing > or =0.77 microM Cu(2+), rather than to a reduction in the size of the Rhizobium population.     

Identification and behavior of reaction products formed by chlorination of ethynylestradiol

Six products were formed by reaction of ethynylestradiol (EE2) with sodium hypochlorite in buffered solutions. 4-Chloroethynylestradiol (4-ClEE2) and 2,4-dichloroethynylestradiol (2,4-diClEE2) were identified as the two major reaction products, using preparative HPLC, MS, and NMR. When EE2 reacted with chlorine at different pHs (pH 5, 7, and 9) or chlorine concentrations (0.2, 1, 2, and 5 mmol/l, corresponding to molar ratios to EE2, 1, 5, 10, and 25, respectively), the formation of 4-ClEE2 and 2,4-diClEE2 was observed under the above conditions, and the highest yields were 20 and 52 mol%, respectively. EE2 was consumed almost completely within 5 min of chlorination by addition of chlorine of more than 1 mmol/l (molar ratio to EE2, 5). On the other hand, the two products existed in highly chlorinated solutions after 60 min (4ClEE2, 1-6 mol%; 2,4-diClEE2, 3-25 mol%). The estrogenic activities of 4-ClEE2 by estrogen receptor alpha or beta binding assay were similar to those of the parent EE2, and the activities of 2,4-diClEE2 were lower about 10 times.     

Unusual products of the aqueous chlorination of atenolol

The reaction of the drug atenolol with hypochlorite under conditions that simulate wastewater disinfection was investigated. The pharmaceutical reacted in 1h yielding three products that were separated by chromatographic techniques and characterized by spectroscopic features. Two unusual products 2-(4-(3-(chloro(2-chloropropan-2-yl)amino)-2-hydroxypropoxy)phenyl) acetamide and 2-(4-(3-formamido-2-hydroxypropoxy)phenyl) acetamide were obtained along with 2-(4-hydroxyphenyl) acetamide. When the reaction was stopped at shorter times only 2-(4-(3-amino-2-hydroxypropoxy)phenyl) acetamide and the dichlorinated product were detected. Tests performed on the seeds of Lactuca sativa show that chlorinated products have phytotoxic activity.     

Phototransformation of clodinafop-propargyl

Photodegradation of the herbicide clodinafop-propargyl was investigated on glass surface under sunlight and UV light. Four photoproducts were identified by NMR, IR, and MS. Major photolysis products were 2-[(5-chloro-3-fluoro-2-pyridyloxy) phenoxy] propanoic acid and prop-2-ynyl-2-[(5-chloro-3-hydroxy-2-pyridyloxy) phenoxy] propanoate, while minor were ethyl 2-[(5-chloro-3-fluoro-2-pyridyloxy) phenoxy] propanoate and 1-hydroxypropanyl-2-[(5-chloro-3-fluoro-2-pyridyloxy) phenoxy] propanoate. Rate of photodegradation followed first-order kinetics with significant correlation coefficient. The major photoproducts were observed in maximum quantity on the 7th and 10th day and further degraded within 15-20 days.     

Sequential photochemical-biological degradation of chlorophenols

UV/TiO₂/H₂O₂, UV/TiO₂ and UV/H₂O₂ were compared as pre-treatment processes for the detoxification of mixtures of 4-chlorophenol (4CP), 2,4-dichlorophenol (DCP), 2,4,6-trichlorophenol (TCP) and pentachlorophenol (PCP) prior to their biological treatment. When each chlorophenol was initially supplied at 50 mg l⁻¹, UV/TiO₂/H₂O₂ treatment supported the highest pollutant removal, COD removal, and dechlorination efficiencies followed by UV/TiO₂ and UV/H₂O₂. The remaining toxicity to Lipedium sativum was similar after all pre-treatments. Chlorophenol photodegradation was always well described by a first order model kinetic (r² > 0.94) and the shortest 4CP, DCP, TCP and PCP half-lives of 8.7, 7.1, 4.5 and 3.3 h, respectively, were achieved during UV/TiO₂/H₂O₂ treatment. No pollutant removal was observed in the controls conducted with H₂O₂ or TiO₂ only. Inoculation of all the photochemically pre-treated mixtures with activated sludge microflora was followed by complete removal of the remaining pollutants. Combined UV/TiO₂/H₂O₂-biological supported the highest detoxification, dechlorination (99%) and COD removal (88%) efficiencies. Similar results were achieved when each chlorophenol was supplied at 100 mg l⁻¹. COD and Cl mass balances indicated UV, UV/H₂O₂, and UV/TiO₂ treatments lead to the formation of recalcitrant photoproducts, some of which were chlorinated.     

Evaluation of pectin binding of heavy metal ions in aqueous solutions

Evaluation of adsorption performance of several industrially manufactured pectins towards some toxic heavy metals was carried out. Adsorption isotherms for divalent cations in simulant aqueous solutions were measured and corresponding distribution coefficients were calculated. The following selectivity sequences we found for pectins: Pb2+ > Cu2+ > Co2+ > Ni2+ > Zn2+ > Cd2+. It was shown that a beet pectin exhibits a high affinity for Pb2+ and Cu2+ ions, an apple pectin for Co2+ ion and a citrus pectin for Ni2+ ion. The binding properties of all pectins towards Zn2+ and Cd2+ ions are extremely poor. The quantitative data on adsorption performance of pectins suggest their applicability as food additives or remedies for efficient removal of Pb2+, Cu2+, Co2+, and Ni2+ ions from different biological systems, including human and animal organisms.     

A comparative study of the removal of 3-indolebutyric acid using advanced oxidation processes

In this study, advanced oxidation technologies, namely Fenton Process (FP), Fenton-Like Process (FLP), ozonation (O3) and O3/H2O2 processes, were applied to synthetic wastewater containing 3-indolebutyric acid (IBA). The effectiveness of each process was investigated at different pH values, Fe(+2), Fe(+3), O3 and H2O2 concentrations with respect to the removal efficiencies for chemical oxygen demand (COD) and total organic carbon (TOC). The best removal efficiencies were seen at pH 3 and 2 mM Fe concentration in both FP and FLP, in which the optimum H2O2 concentrations were 6 mM for FP and 10 mM for FLP. Optimum process conditions were pH 12 for the O3 process, pH 9 for the O3/H2O2 process and 1:1 O3/H2O2 molar ratio. The highest COD removal efficiency was 86 percent, obtained in the O3/H2O2 process and the highest TOC removal efficiency was obtained at 77 percent in the FP.     

Comparison of catalytic activity of two platinised TiO2 films towards the oxidation of organic pollutants

Two types of platinised TiO2 films, i.e., Pt-TiO2/ITO and Pt(TiO2)/ITO, were prepared by a procedure of dip-coating and subsequent photo-deposition, and photo-deposition and subsequent dip-coating, respectively. They were well characterized by DRS, XRD spectra, SEM microscopy and photoelectrochemical measurement. Their photocatalytic, dark catalytic and photoelectrocatalytic activities were investigated using formic acid as a model organic pollutants. Compared with pure TiO2/ITO film, the photocatalytic activity of the platinised TiO2 films were apparently improved. However, the improvement was considerably dependent on the preparation method of these films. Pt-TiO2/ITO not only possessed higher photocatalytic activity but also showed a dark catalytic activity towards HCOOH degradation. As a sequence, it was first emphasized that the dark catalytic effect of Pt-TiO2/ITO was partly responsible for degradation of formic acid in the photocatalytic oxidation process. Although the Pt(TiO2)/ITO film does not exhibit the dark catalytic activity, its photocatalytic degradation efficiencies towards HCOOH are higher than that of Pt-TiO2/ITO film. Therefore, in view of enhanced photocatalytic activity, the Pt(TiO2)/ITO was more favored than Pt-TiO2/ITO film.     

Effect of ZnFe2O4 doping on the photocatalytic activity of TiO2

The photocatalytic oxidation of the organic pollutants with the TiO2 as photocatalyst has been widely studied in the world, and many achievements have been got. The degradation of pollutants is highly related with the photocatalytic activity of TiO2. It is demonstrated that doping ions or oxides to TiO2 is one way to enhance the photocatalytic activity of TiO2. In this paper, the ZnFe2O4-doped TiO2 nanoparticles were prepared from butyl titanate by a sol-gel method and characterized by means of X-ray diffraction (XRD) and transmission electron microscopy (TEM). The results showed that when TiO2 was doped with ZnFe2O4, its particle size will decrease and its crystal structure will partly transform from anatase to rutile. The photocatalytic activity of the elaborated powders was studied following the degradation of Rhodamine B. The results showed that doping ZnFe2O4 to TiO2 will enhance the photocatalytic activity of TiO2 and that ZnFe2O4-doped TiO2 in the coexistence of anatase and rutile has higher efficiency for the degradation of Rhodamine B than that in the anatase phase alone. Also the different role of O2 in the direct photolysis and photocatalysis of Rhodamine B was discussed.     

Effects of oxygen on formation of PCB and PCDD/F on extracted fly ash in the presence of carbon and cupric salt

The effect of oxygen-nitrogen atmosphere (N2 + 10%O2, N2 + 1%O2 and 99.999% N2) on the formation of PCB, PCDD and PCDF by the de novo synthetic reactions in the system consisting of extracted fly ash (from municipal waste incinerators--MWI), activated carbon, CuCl2 x 2H2O and NaCl at 340 degrees C was studied. The content of PCDD/F for systems with 10%O2, 1%O2 and 99.999% N2 was decreasing and corresponded to 17,304, 5544, and 1437 ng/sample. In all studied systems the isomer OCDD/F was prevailing. The content of PCBs in the same system was also decreasing from 1214 to 166 ng/g. Formation of nonortho PCB was relatively high compared to the system where only nitrogen was present. The possible mechanism of formation is outlined.