On-road measurement of fine particle and nitrogen oxide emissions from light- and heavy-duty motor vehicles

An updated assessment of fine particle emissions from light- and heavy-duty vehicles is needed due to recent changes to the composition of gasoline and diesel fuel, more stringent emission standards applying to new vehicles sold in the 1990s, and the adoption of a new ambient air quality standard for fine particulate matter (PM_2.5) in the United States. This paper reports the measurement of emissions from vehicles in a northern California roadway tunnel during summer 1997. Separate measurements were made of uphill traffic in two tunnel bores: one bore carried both light-duty vehicles and heavy-duty diesel trucks, and the second bore was reserved for light-duty vehicles. Ninety-eight percent of the light-duty vehicles were gasoline-powered. In the tunnel, heavy-duty diesel trucks emitted 24, 37, and 21 times more fine particle, black carbon, and sulfate mass per unit mass of fuel burned than light-duty vehicles. Heavy-duty diesel trucks also emitted 15–20 times the number of particles per unit mass of fuel burned compared to light-duty vehicles. Fine particle emissions from both vehicle classes were composed mostly of carbon; diesel-derived particulate matter contained more black carbon (51±11% of PM_2.5 mass) than did light-duty fine particle emissions (33±4%). Sulfate comprised only 2% of total fine particle emissions for both vehicle classes. Sulfate emissions measured in this study for heavy-duty diesel trucks are significantly lower than values reported in earlier studies conducted before the introduction of low-sulfur diesel fuel. This study suggests that heavy-duty diesel vehicles in California are responsible for nearly half of oxides of nitrogen emissions and greater than three-quarters of exhaust fine particle emissions from on-road motor vehicles.     

Formaldehyde,Melhanol and Hydrocarbon Emissions from Methanol-fueled Cars

Exhaust and evaporative emissions tests were conducted on several methanol- and gasoline-fueled vehicles. Separate samples for chromatographlc analysis of formaldehyde, methanol, and Individual hydrocarbons were collected in each of the three phases of the driving cycle and in each of the two portions of the evaporative emissions test. One vehicle, equipped with an experimental variable-fuel engine, was tested using methanol/gasoline fuel mixtures of 100, 85, 50,15, and 0 percent methanol. Combustion-generated hydrocarbons were lowest using methanol fuel, and increased several-fold as the gasoline fraction was increased. Gasoline components In the exhaust Increased from zero as the gasoline fraction of the fuel was Increased. On the other hand, formaldehyde emissions were several times higher using methanol fuel than they were using gasoline. A dedicated methanol car and the variable-fuel car gave similar emissions patterns when they both were tested using methanol fuel. The organic-carbon composition of the exhaust was 85-90 percent methanol, 5-7 percent formaldehyde, and 3-9 percent hydrocarbons. Several cars that were tested using gasoline emitted similar distributions of hydrocarbons, even through the vehicles represented a broad range of current and developmental engine families and emissions control systems. These vehicles continue the trend of the past twenty years toward less photochemically reactive exhaust, with higher percentages of methane and total alkanes, and correspondingly lower percentages of oleflns and aromatlcs.     

Optimized combinations of abatement strategies for urban mobile sources

The maximum incremental reactivity (MIR) scale was chosen as a practical index for quantifying ozone-forming impacts. The integer linear and nonlinear programming techniques were employed as the optimization method to maximize MIR and volatile organic compound (VOC) reductions, and minimize ozone's marginal cost with varied control costs. Mobile vehicles were divided into nine categories according to the demands of decision makers and the distinctive features of local circumstance in metro-Taipei. The emission factor (EF) and vehicle kilometers traveled (VKT) of each kind of vehicle were estimated by MOBILE5B model via native parameters and questionnaires. Compressed natural gas (CNG) and inspection and maintenance (I/M) were the alternative control programs for buses and touring buses; liquefied petroleum gas (LPG), I/M, methanol, electrical vehicle (EV) were for taxis and low duty gasoline vehicles. EV, methanol, and I/M were the possible control methods for two-stroke and four-stroke engine motorcycles; I/M programs for low-duty diesel trucks, heavy-duty diesel trucks, and low-duty gasoline trucks. The results include the emission ratios of specific vehicle to all vehicles, the best combination of abated measures based on different objectives, and the marginal cost for ozone and VOC with varied control costs.     

A life-cycle comparison of alternative automobile fuels

We examine the life cycles of gasoline, diesel, compressed natural gas (CNG), and ethanol (C2H5OH)-fueled internal combustion engine (ICE) automobiles. Port and direct injection and spark and compression ignition engines are examined. We investigate diesel fuel from both petroleum and biosources as well as C2H5OH from corn, herbaceous bio-mass, and woody biomass. The baseline vehicle is a gasoline-fueled 1998 Ford Taurus. We optimize the other fuel/powertrain combinations for each specific fuel as a part of making the vehicles comparable to the baseline in terms of range, emissions level, and vehicle lifetime. Life-cycle calculations are done using the economic input-output life-cycle analysis (EIO-LCA) software; fuel cycles and vehicle end-of-life stages are based on published model results. We find that recent advances in gasoline vehicles, the low petroleum price, and the extensive gasoline infrastructure make it difficult for any alternative fuel to become commercially viable. The most attractive alternative fuel is compressed natural gas because it is less expensive than gasoline, has lower regulated pollutant and toxics emissions, produces less greenhouse gas (GHG) emissions, and is available in North America in large quantities. However, the bulk and weight of gas storage cylinders required for the vehicle to attain a range comparable to that of gasoline vehicles necessitates a redesign of the engine and chassis. Additional natural gas transportation and distribution infrastructure is required for large-scale use of natural gas for transportation. Diesel engines are extremely attractive in terms of energy efficiency, but expert judgment is divided on whether these engines will be able to meet strict emissions standards, even with reformulated fuel. The attractiveness of direct injection engines depends on their being able to meet strict emissions standards without losing their greater efficiency. Biofuels offer lower GHG emissions, are sustainable, and reduce the demand for imported fuels. Fuels from food sources, such as biodiesel from soybeans and C2H5OH from corn, can be attractive only if the co-products are in high demand and if the fuel production does not diminish the food supply. C2H5OH from herbaceous or woody biomass could replace the gasoline burned in the light-duty fleet while supplying electricity as a co-product. While it costs more than gasoline, bioethanol would be attractive if the price of gasoline doubled, if significant reductions in GHG emissions were required, or if fuel economy regulations for gasoline vehicles were tightened.     

An investigation on the physical,chemical and ecotoxicological characteristics of particulate matter emitted from light-duty vehicles

Particulate matter (PM) emitted from three light-duty vehicles was studied in terms of its physicochemical and ecotoxicological character using Microtox^® bioassay tests. A diesel vehicle equipped with an oxidation catalyst emitted PM which consisted of carbon species at over 97%. PM from a diesel vehicle with a particle filter (DPF) consisted of almost equal amounts of carbon species and ions, while a gasoline vehicle emitted PM consisting of ～90% carbon and ～10% ions. Both the DPF and the gasoline vehicles produced a distinct nucleation mode at 120 km/h. The PM emitted from the DPF and the gasoline vehicles was less ecotoxic than that of conventional diesel, but not in direct proportion to the emission levels of the different vehicles. These results indicate that PM emission reductions are not equally translated into ecotoxicity reductions, implying some deficiencies on the actual environmental impact of emission control technologies and regulations.     

A Life-Cycle Comparison of Alternative Automobile Fuels

ABSTRACT

We examine the life cycles of gasoline, diesel, compressed natural gas (CNG), and ethanol (C₂H₅OH)-fueled internal combustion engine (ICE) automobiles. Port and direct injection and spark and compression ignition engines are examined. We investigate diesel fuel from both petroleum and biosources as well as C₂H₅OH from corn, herbaceous bio-mass, and woody biomass. The baseline vehicle is a gasoline-fueled 1998 Ford Taurus. We optimize the other fuel/powertrain combinations for each specific fuel as a part of making the vehicles comparable to the baseline in terms of range, emissions level, and vehicle lifetime. Life-cycle calculations are done using the economic input-output life-cycle analysis (EIO-LCA) software; fuel cycles and vehicle end-of-life stages are based on published model results.

We find that recent advances in gasoline vehicles, the low petroleum price, and the extensive gasoline infrastructure make it difficult for any alternative fuel to become commercially viable. The most attractive alternative fuel is compressed natural gas because it is less expensive than gasoline, has lower regulated pollutant and toxics emissions, produces less greenhouse gas (GHG) emissions, and is available in North America in large quantities. However, the bulk and weight of gas storage cylinders required for the vehicle to attain a range comparable to that of gasoline vehicles necessitates a redesign of the engine and chassis. Additional natural gas transportation and distribution infrastructure is required for large-scale use of natural gas for transportation. Diesel engines are extremely attractive in terms of energy efficiency, but expert judgment is divided on whether these engines will be able to meet strict emissions standards, even with reformulated fuel. The attractiveness of direct injection engines depends on their being able to meet strict emissions standards without losing their greater efficiency. Biofuels offer lower GHG emissions, are sustainable, and reduce the demand for imported fuels. Fuels from food sources, such as biodiesel from soybeans and C₂H₅OH from corn, can be attractive only if the co-products are in high demand and if the fuel production does not diminish the food supply. C₂H₅OH from herbaceous or woody biomass could replace the gasoline burned in the light-duty fleet while supplying electricity as a co-product. While it costs more than gasoline, bioethanol would be attractive if the price of gasoline doubled, if significant reductions in GHG emissions were required, or if fuel economy regulations for gasoline vehicles were tightened.     

Toxic emissions from mobile sources: a total fuel-cycle analysis for conventional and alternative fuel vehicles

Mobile sources are among the largest contributors of four hazardous air pollutants--benzene, 1,3-butadiene, acetaldehyde, and formaldehyde--in urban areas. At the same time, federal and state governments are promoting the use of alternative fuel vehicles as a means to curb local air pollution. As yet, the impact of this movement toward alternative fuels with respect to toxic emissions has not been well studied. The purpose of this paper is to compare toxic emissions from vehicles operating on a variety of fuels, including reformulated gasoline (RFG), natural gas, ethanol, methanol, liquid petroleum gas (LPG), and electricity. This study uses a version of Argonne National Laboratory's Greenhouse Gas, Regulated Emissions, and Energy Use in Transportation (GREET) model, appropriately modified to estimate toxic emissions. The GREET model conducts a total fuel-cycle analysis that calculates emissions from both downstream (e.g., operation of the vehicle) and upstream (e.g., fuel production and distribution) stages of the fuel cycle. We find that almost all of the fuels studied reduce 1,3-butadiene emissions compared with conventional gasoline (CG). However, the use of ethanol in E85 (fuel made with 85% ethanol) or RFG leads to increased acetaldehyde emissions, and the use of methanol, ethanol, and compressed natural gas (CNG) may result in increased formaldehyde emissions. When the modeling results for the four air toxics are considered together with their cancer risk factors, all the fuels and vehicle technologies show air toxic emission reduction benefits.     

Toxic Emissions from Mobile Sources: A Total Fuel-Cycle Analysis for Conventional and Alternative Fuel Vehicles

ABSTRACT

Mobile sources are among the largest contributors of four hazardous air pollutants—benzene, 1,3-butadiene, acetal-dehyde, and formaldehyde—in urban areas. At the same time, federal and state governments are promoting the use of alternative fuel vehicles as a means to curb local air pollution. As yet, the impact of this movement toward alternative fuels with respect to toxic emissions has not been well studied. The purpose of this paper is to compare toxic emissions from vehicles operating on a variety of fuels, including reformulated gasoline (RFG), natural gas, ethanol, methanol, liquid petroleum gas (LPG), and electricity. This study uses a version of Argonne National Laboratory's Greenhouse Gas, Regulated Emissions, and Energy Use in Transportation (GREET) model, appropriately modified to estimate toxic emissions. The GREET model conducts a total fuel-cycle analysis that calculates emissions from both downstream (e.g., operation of the vehicle) and upstream (e.g., fuel production and distribution) stages of the fuel cycle. We find that almost all of the fuels studied reduce 1,3-buta-diene emissions compared with conventional gasoline (CG). However, the use of ethanol in E85 (fuel made with 85% ethanol) or RFG leads to increased acetaldehyde emissions, and the use of methanol, ethanol, and compressed natural gas (CNG) may result in increased formaldehyde emissions. When the modeling results for the four air toxics are considered together with their cancer risk factors, all the fuels and vehicle technologies show air toxic emission reduction benefits.     

Determination of single particle mass spectral signatures from heavy-duty diesel vehicle emissions for PM2.5 source apportionment

The size and chemical composition of individual diesel exhaust particles were measured in order to determine unique mass spectral signatures that can be used to identify particle sources in future ambient studies. The exhaust emissions from seven in-use heavy-duty diesel vehicles (HDDVs) operating on a chassis dynamometer were passed through a dilution tunnel and residence chamber and analyzed in real time by aerosol time-of-flight mass spectrometry (ATOFMS). Seven distinct particle types describe the majority of particles emitted by HDDVs and were emitted by all seven vehicles. The dominant chemical types originated from unburned lubricant oil, and the contributions of the various types varied with particle size and driving conditions. A comparison of light-duty vehicle (LDV) exhaust particles with the HDDV signatures provide insight into the challenges associated with developing an accurate source apportionment technique and possible ways of how they may be overcome.     

Emission rates and comparative chemical composition from selected in-use diesel and gasoline-fueled vehicles

Emission samples for toxicity testing and detailed chemical characterization were collected from a variety of gasoline- and diesel-fueled in-use vehicles operated on the Unified Driving Cycle on a chassis dynamometer. Gasoline vehicles included normal particle mass (particulate matter [PM]) emitters (tested at 72 and 30 degrees F), "black" and "white" smokers, and a new-technology vehicle (tested at 72 degrees F). Diesel vehicles included current-technology vehicles (tested at 72 and 30 degrees F) and a high PM emitter. Total PM emission rates ranged from below 3 mg/mi up to more than 700 mg/mi for the white smoker gasoline vehicle. Emission rates of organic and elemental carbon (OC/EC), elements (metals and associated analytes), ions, and a variety of particulate and semi-volatile organic compounds (polycyclic aromatic hydrocarbons [PAH], nitro-PAH, oxy-PAH, hopanes, and steranes) are reported for these vehicles. Speciated organic analysis also was conducted on the fuels and lube oils obtained from these vehicles after the emissions testing. The compositions of emissions were highly dependent on the fuel type (gasoline vs. diesel), the state of vehicle maintenance (low, average, or high emitters; white or black smokers), and ambient conditions (i.e., temperature) of the vehicles. Fuel and oil analyses from these vehicles showed that oil served as a repository for combustion byproducts (e.g., PAH), and oil-burning gasoline vehicles emitted PAH in higher concentrations than did other vehicles. These PAH emissions matched the PAH compositions observed in oil.     

不同类型机动车尾气中芳香烃化合物含量分析

首次对北京市9种车辆、5种燃料在不同工况下排放芳香烃化合物的特征．进行了定量研究。结果表明，车型、燃料、净化器及工况等因素对排放量产生影响，电喷车比化油器车芳香烃化合物排放量低；汽油车排放量最高，柴油车其次，LPG及CNG车排放量最低；使用净化器可以降低芳香烃排放量；不同工况对排放量的影响随车型，燃料类型的不同而不同。     

Semi-volatile and particulate emissions from the combustion of alternative diesel fuels

Motor vehicle emissions are a major anthropogenic source of air pollution and contribute to the deterioration of urban air quality. In this paper, we report results of a laboratory investigation of particle formation from four different alternative diesel fuels, namely, compressed natural gas (CNG), dimethyl ether (DME), biodiesel, and diesel, under fuel-rich conditions in the temperature range of 800-1200 degrees C at pressures of approximately 24 atm. A single pulse shock tube was used to simulate compression ignition (CI) combustion conditions. Gaseous fuels (CNG and DME) were exposed premixed in air while liquid fuels (diesel and biodiesel) were injected using a high-pressure liquid injector. The results of surface analysis using a scanning electron microscope showed that the particles formed from combustion of all four of the above-mentioned fuels had a mean diameter less than 0.1 microm. From results of gravimetric analysis and fuel injection size it was found that under the test conditions described above the relative particulate yields from CNG, DME, biodiesel, and diesel were 0.30%. 0.026%, 0.52%, and 0.51%, respectively. Chemical analysis of particles showed that DME combustion particles had the highest soluble organic fraction (SOF) at 71%, followed by biodiesel (66%), CNG (38%) and diesel (20%). This illustrates that in case of both gaseous and liquid fuels, oxygenated fuels have a higher SOF than non-oxygenated fuels.     

Model and algorithm for bi-fuel vehicle routing problem to reduce GHG emissions

Because of the harmful effects of greenhouse gas (GHG) emitted by petroleum-based fuels, the adoption of alternative green fuels such as biodiesel and compressed natural gas (CNG) is an inevitable trend in the transportation sector. However, the transition to alternative fuel vehicle (AFV) fleets is not easy and, particularly at the beginning of the transition period, drivers may be forced to travel long distances to reach alternative fueling stations (AFSs). In this paper, the utilization of bi-fuel vehicles is proposed as an operational approach. We present a mathematical model to address vehicle routing problem (VRP) with bi-fuel vehicles and show that the utilization of bi-fuel vehicles can lead to a significant reduction in GHG emissions. Moreover, a simulated annealing algorithm is adopted to solve large instances of this problem. The performance of the proposed algorithm is evaluated on some random instances.     

Exhaust Emissions From In-Use Alternative Fuel Vehicles

Abstract

This study examines exhaust emissions from 11 vehicles tested on compressed natural gas, liquefied petroleum gas, methanol, ethanol, and reformulated gasoline fuels (22 vehicle/ fuel combinations). The paper highlights ozone precursor and toxic emissions. Emission rates from some of the presumably well-maintained, low-mileage test vehicles were higher than expected, but fuel effects were consistent with findings of similar studies. Aggregate toxic and non-methane organic emission rates from the variable/flexible fuel vehicles were higher with alcohol fuels than with reformulated gasoline. Lower specific reactivities for emissions with the alcohol fuels offset this negative trait. Specific reactivities of the organic emissions with the alternative fuels were consistently lower than those with the gasoline blends. Compressed natural gas and liquefied petroleum gas fuels had the lowest values. Although specific reactivities were expected to vary from fuel-to-fuel, they also varied considerably from vehicle-to-vehicle.     

Germany

ABSTRACT

The 1988 Alternative Motor Fuels Act and the 1990 Clean Air Act Amendments require examination of the potential to favorably influence air quality by changing the composition of motor vehicle fuels. Motor vehicle tailpipe and evaporative emissions were characterized using laboratory simulations of roadway driving conditions and a variety of vehicle-fuel technologies (reformulated gasoline (RFG), methanol (M85), ethanol (E85), and natural gas (CNG)). Speciated organic compound (with Carter MIR ozone potential), CO, and NO_x emission rates and fuel economy were characterized. The Carter MIR ozone potential of combined Federal Test Procedure (FTP) tailpipe and evaporative emissions was reduced more than 90% with CNG relative to RFG, M85, and E85 fuels. FTP toxic compound emissions (benzene, formaldehyde, acetalde-hyde, and 1,3-butadiene) were greater with M85 and E85 fuels than with RFG fuel, and less with CNG fuel than RFG fuel. The most abundant toxic compound was benzene with RFG fuel, formaldehyde with M85 fuel, and acetaldehyde with E85 fuel. FTP MPG fuel economies were reduced with M85 and E85 fuels relative to RFG fuel, consistent with their lower BTU/gal. Energy efficiencies (BTU/mi) were improved with all the alternative fuels relative to RFG. Carter MIR ozone potential was generally reduced with the alternative fuels relative to RFG fuel under REP05 (high speeds and acceleration rates) driving conditions (most significantly with CNG). Toxic aldehyde emissions were reduced under REP05 conditions relative to FTP conditions with all the tested fuels, and toxic benzene emissions were elevated under high acceleration conditions.     

Variations in speciated emissions from spark-ignition and compression-ignition motor vehicles in California's south coast air basin

The U.S. Department of Energy Gasoline/Diesel PM Split Study examined the sources of uncertainties in using an organic compound-based chemical mass balance receptor model to quantify the contributions of spark-ignition (SI) and compression-ignition (CI) engine exhaust to ambient fine particulate matter (PM2.5). This paper presents the chemical composition profiles of SI and CI engine exhaust from the vehicle-testing portion of the study. Chemical analysis of source samples consisted of gravimetric mass, elements, ions, organic carbon (OC), and elemental carbon (EC) by the Interagency Monitoring of Protected Visual Environments (IMPROVE) and Speciation Trends Network (STN) thermal/optical methods, polycyclic aromatic hydrocarbons (PAHs), hopanes, steranes, alkanes, and polar organic compounds. More than half of the mass of carbonaceous particles emitted by heavy-duty diesel trucks was EC (IMPROVE) and emissions from SI vehicles contained predominantly OC. Although total carbon (TC) by the IMPROVE and STN protocols agreed well for all of the samples, the STN/IMPROVE ratios for EC from SI exhaust decreased with decreasing sample loading. SI vehicles, whether low or high emitters, emitted greater amounts of high-molecular-weight particulate PAHs (benzo[ghi]perylene, indeno[1,2,3-cd]pyrene, and coronene) than did CI vehicles. Diesel emissions contained higher abundances of two- to four-ring semivolatile PAHs. Diacids were emitted by CI vehicles but are also prevalent in secondary organic aerosols, so they cannot be considered unique tracers. Hopanes and steranes were present in lubricating oil with similar composition for both gasoline and diesel vehicles and were negligible in gasoline or diesel fuels. CI vehicles emitted greater total amounts of hopanes and steranes on a mass per mile basis, but abundances were comparable to SI exhaust normalized to TC emissions within measurement uncertainty. The combustion-produced high-molecular-weight PAHs were found in used gasoline motor oil but not in fresh oil and are negligible in used diesel engine oil. The contributions of lubrication oils to abundances of these PAHs in the exhaust were large in some cases and were variable with the age and consumption rate of the oil. These factors contributed to the observed variations in their abundances to total carbon or PM2.5 among the SI composition profiles.     

Effects of Fuel Variables on Diesel Emissions

The body of information presented in this paper is directed towards engineers in the field of environmental sciences involved in measuring and/or evaluating the emissions from a variety of diesel engines or vehicles. This paper summarizes recent data obtained by EPA on identification and quantification of different emissions (i.e. characterization) from a variety of diesel engines.

Extensive work has been done comparing emissions from some light duty diesel and gasoline passenger cars. The work on the diesel vehicles was expanded to include tests with five different diesel fuels to determine how fuel composition affects emissions. This work showed that use of a poorer quality fuel frequently made emissions worse. The investigation of fuel composition continued with a project in which specific fuel parameters were systematically varied to determine their effect on emissions. EPA is presently testing a variety of fuels derived from coal and oil shale to determine their effects on emissions.

EPA has also tested a heavy duty Volvo diesel bus engine designed to run on methanol and diesel fuel, each injected through its own injection system. The use of the dual fuel resulted in a reduction in particulates and NO _x but an increase in HC and CO compared to a baseline Volvo diesel engine running on pure diesel fuel.

Finally, some Ames bioassay tests have been performed on samples from the diesel passenger cars operated on various fuels and blends. An increase in Ames test response (mutagenicity) was seen when the higher aromatic blend was used and also when a commercial cetane improver was used. Samples from the Volvo diesel bus engine fueled with methanol and diesel fuel showed that use of a catalyst increased the Ames response.     

Mercury emissions from automobiles using gasoline,diesel, and LPG

Mercury (Hg) emissions from gasoline, diesel, and liquefied petroleum gas (LPG) vehicles were measured and speciated (particulate, oxidized, and elemental mercury). First, three different fuel types were analyzed for their original Hg contents; 571.1±4.5 ng L⁻¹ for gasoline, 185.7±2.6 ng L⁻¹ for diesel, and 1230.3±23.5 ng L⁻¹ for LPG. All three vehicles were then tested at idling and driving modes. Hg in the exhaust gas was mostly in elemental form (Hg⁰), and no detectable levels of particulate (Hg^p) or oxidized (Hg²⁺) mercury were measured. At idling modes, Hg concentrations in the exhaust gas of gasoline, diesel, and LPG vehicles were 1.5–9.1, 1.6–3.5, and 10.2–18.6 ng m⁻³, respectively. At driving modes, Hg concentrations were 3.8–16.8 ng m⁻³ (gasoline), 2.8–8.5 ng m⁻³ (diesel), and 20.0–26.9 ng m⁻³ (LPG). For all three vehicles, Hg concentrations at driving modes were higher than at idling modes. Furthermore, Hg emissions from LPG vehicle was highest of all three vehicle types tested, both at idling and driving modes, as expected from the fact that it had the highest original fuel Hg content.     

机动车尾气VOCs排放特征及减排措施研究

分析了机动车尾气挥发性有机物(VOCs)的排放特征,发现尾气VOCs排放具有明显的日变化和季节变化特征。不同区域不同车型机动车尾气VOCs成分谱略有差异,轻型汽油车尾气VOCs中芳香烃和烷烃含量较高,柴油车烷烃含量较高。尾气排放受机动车保有量、行驶里程、维护保养水平、行驶速度和燃油标准、排放标准等因素影响。从优先控制汽油车、加快机动车更新、采取本地化减排措施、加强多元管理措施、提高科研水平等方面提出了针对性的减排措施。     

Ft. McHenry tunnel study: Source profiles and mercury emissions from diesel and gasoline powered vehicles

During the fall of 1998, the US Environmental Protection Agency and the Florida Department of Environmental Protection sponsored a 7-day study at the Ft. McHenry tunnel in Baltimore, MD with the objective of obtaining PM_2.5 vehicle source profiles for use in atmospheric mercury source apportionment studies. PM_2.5 emission profiles from gasoline and diesel powered vehicles were developed from analysis of trace elements, polycyclic aromatic hydrocarbons (PAH), and condensed aliphatic hydrocarbons. PM_2.5 samples were collected using commercially available sampling systems and were extracted and analyzed using conventional well-established methods. Both inorganic and organic profiles were sufficiently unique to mathematically discriminate the contributions from each source type using a chemical mass balance source apportionment approach. However, only the organic source profiles provided unique PAH tracers (e.g., fluoranthene, pyrene, and chrysene) for diesel combustion that could be used to identify source contributions generated using multivariate statistical receptor modeling approaches. In addition, the study found significant emission of gaseous elemental mercury (Hg⁰), divalent reactive gaseous mercury (RGM), and particulate mercury (Hg(p)) from gasoline but not from diesel powered motor vehicles. Fuel analysis supported the tunnel measurement results showing that total mercury content in all grades of gasoline (284±108 ng L⁻¹) was substantially higher than total mercury content in diesel fuel (62±37 ng L⁻¹) collected contemporaneously at local Baltimore retailers.