CuCoOx/TiO2催化氧化NO性能研究

采用浸渍法制备了CuCoOx/TiO₂催化剂，考察了焙烧温度、反应温度、氧含量、NO浓度和空间速度对催化剂催化氧化NO性能的影响，并考察了催化剂的抗硫抗水性能。XRD、TPR和BET分析表明，350℃焙烧的催化剂具有CuCo₂O₄尖晶石结构，比表面积大，对NO的氧化效果好。在空速为5 000 h^-1，NO进口浓度500 mg/m³，含氧量10%的条件下，反应温度300℃时NO转化率可达79.5%，250℃时NO转化率接近50%。该催化剂具有良好的单独抗SO₂、抗H₂O毒化性能，H₂O和SO₂同时存在时很快失活。该催化剂可用于不同时含H₂O和SO₂的含NO气体催化氧化后再吸收处理。     

CuMnOx/γ-Al2O3及稀土助剂对VOCs催化燃烧性能的影响

利用浸渍法制备了Cu-Mn复合氧化物催化剂和加入不同稀土含量的Cu-Mn复合氧化物催化剂，通过实验优选出加入稀土催化剂中稀土含量的最优配比，以气相色谱为检测手段，考察了加入稀土和不加稀土催化剂的催化燃烧性能，结果表明，加入稀土的催化剂T₉₉（催化处理效率达到99%时的温度）比不加稀土的催化剂降低30～40℃，具有更好的低温活性，且对多种VOCs均能降低反应温度。     

溶胶-凝胶法制备颗粒状催化剂低温SCR脱硝性能

采用溶胶凝胶法制备了Mn-Ce/Ti O2催化剂,并将其用于低温NH3选择催化还原NO的反应(NH3-SCR),考察了反应温度、空速、氧气浓度、氮氧化物浓度和氨氮比等反应条件对催化剂性能的影响。结果表明,NO入口浓度为800~1 600 mg/m3时,催化剂活性受NO初始浓度的影响较小。反应温度和氨氮比对NO转化率影响显著,100~150℃温度范围内,NO转化率随温度升高快速上升;当[NH3]/[NO]1.1时,随着[NH3]/[NO]的增加,NO转化率很快上升。反应体系中适当的O2浓度可促进NO还原为N2。空速大于10 000 h-1时,NO转化率随着空速的增大而降低。     

CuCoOx／TiO2催化氧化NO性能研究

采用浸渍法制备了CuCoOx／TiO2催化剂，考察了焙烧温度、反应温度、氧含量、NO浓度和空间速度对催化剂催化氧化NO性能的影响，并考察了催化剂的抗硫抗水性能。XRD、TPR和BET分析表明，350℃焙烧的催化剂具有CuCo2O4尖晶石结构，比表面积大，对NO的氧化效果好。在空速为5000h^-1，NO进口浓度500mg／m^3，含氧量10％的条件下，反应温度300℃时NO转化率可达79．5％，250℃时NO转化率接近50％。该催化剂具有良好的单独抗SO2、抗H2O毒化性能，H2O和SO2同时存在时很快失活。该催化剂可用于不同时含H2O和SO2的含NO气体催化氧化后再吸收处理。     

CuO/γ-Al2O3的制备及其湿式催化氧化性能研究

针对常温常压的废水双氧水催化氧化，采用浸渍法制备CuO/γ-Al₂O₃催化剂，利用比表面积、XRD手段表征了制备工艺对催化剂的影响，以模拟苯酚废水为研究对象考察催化剂的催化性能。研究表明，焙烧温度和活性组分含量等显著影响催化剂的性能，催化剂对双氧水催化氧化苯酚溶液具有较高的催化活性。     

CuCoO_x/TiO_2催化氧化NO性能研究

采用浸渍法制备了CuCoOx/TiO2催化剂,考察了焙烧温度、反应温度、氧含量、NO浓度和空间速度对催化剂催化氧化NO性能的影响,并考察了催化剂的抗硫抗水性能.XRD、TPR和BET分析表明,350℃焙烧的催化剂具有Cu-Co2O4尖晶石结构,比表面积大,对N0的氧化效果好.在空速为5 000 h-1,NO进口浓度500 mg/m3,含氧量10%的条件下,反应温度300cc时N0转化率可达79.5%,250℃时N0转化率接近50%.该催化剂具有良好的单独抗SO2、抗H2O毒化性能,H2O和SO2同时存在时很快失活.该催化剂可用于不同时含H2O和SO2的含NO气体催化氧化后再吸收处理.     

Au/SnO2催化氧化CO性能的研究

以SnO₂为载体，Au为活性组分，采用真空浸渍法、共沉淀法、沉积沉淀法制备CO氧化的催化剂，同时还制备双金属体系催化剂Au-Pd/SnO₂和Au-Pt/SnO₂。用气相色谱对所制备的催化剂进行活性评价，运用DSC、SEM、XRD、BET等对催化剂进行表征。在本实验条件下，载体二氧化锡焙烧温度为500 ℃，催化剂成型温度为350 ℃，金负载量为3%(wt.)时，用沉积-沉淀法制备的Au/SnO₂活性最好，在18 ℃，空速为24 000 h-1条件下就能将CO（浓度为4%）完全氧化为CO₂；添加铂和钯可提高Au/SnO₂对CO的催化活性。     

γ-Al_2O_3负载Mn基催化剂低温催化臭氧氧化NO

利用等体积浸渍法制备γ-Al_2O_3负载Mn基催化剂,考察了掺杂元素种类,掺杂元素与Mn元素摩尔比以及煅烧温度对NO低温(100℃)催化氧化活性的影响,并对催化剂在有SO_2或H_2O的烟气中的稳定性进行了探究。结果表明,掺杂元素为Ce,Ce/Mn=0.4,煅烧温度为500℃条件下制备的催化剂NO催化活性最佳,在NO体积浓度为500×10~(-6),臭氧浓度为20.9 mg·L~(-1),n(O_3)/n(NO)=0.2,反应温度为100℃,模拟烟气总流量为1.0 L·min~(-1),模拟烟气相对湿度为4%的条件下,NO的转化率最高可达70%。此外,还对催化剂在不同条件下的稳定性和活性恢复情况进行了探究。实验最终实现了在低O_3浓度条件下达到较高NO转化率的目的,为烟气脱硝提供了一种具有应用潜力的新技术。     

全硅β分子筛催化氧化NO性能研究

针对NO氧化催化剂抗水汽性差、活性温度高等问题,本研究采用疏水型全硅β分子筛为催化剂,在NO进口浓度为0.05%(体积分数)、O2浓度为20.7%(体积分数)条件下,考察了反应温度(20~60℃)、相对湿度(0%~100%)、空速(360 h-1~20 000 h-1)等因素对NO催化氧化的影响。研究结果表明,随着反应温度升高,干气和湿气下NO氧化率都下降,低温有利于NO氧化;在20℃,空速为20 000 h-1条件下,相对湿度从0%增大到100%时,NO氧化率从49%下降到34%。反应温度升高会抑制水汽对NO氧化的影响。240 h催化剂稳定性实验结果表明,在30℃,NO进口浓度为0.05%,空速为7 200 h-1时,干气和饱和水汽下的NO氧化率分别能稳定地维持在67%和56%水平,说明全硅β分子筛即使在饱和水汽下也具有良好的稳定性及抗水汽性。     

制备方法对Mn-Ce/TiO2催化剂低温选择性催化还原活性的影响

采用溶胶凝胶法、浸渍法以及两者相结合的方法制备了Mn-Ce/TiO2催化剂.运用XRD、BET和SEM等技术对催化剂进行了表征,发现溶胶凝胶法制备的Mn-Ce/TiO2催化剂为锐钛矿结构,具有较大的比表面积,中孔结构丰富,Mn、Ce活性组分在载体表面高度分散或形成了无定形结构.实验研究了催化剂对氨选择性催化还原NO反应的催化性能,结果表明,用溶胶凝胶法制备的Mn-Ce/TiO2催化剂脱硝活性最好,当Mn、Ce负载量为20％,NH3/NO摩尔比为1.1,空速为9 436 h-1,烟气温度为240℃时,NO转化率大于90％.     

Relationship between Pd oxidation states on TiO2 and the photocatalytic oxidation behaviors of nitric oxide

This study has been undertaken to investigate the relationship between Pd oxidation states on TiO₂ photocatalysts and their photocatalytic oxidation behaviors of NO. Three types of Pd-modified TiO₂ with different Pd oxidation states were prepared by wet impregnation method, neutralization method and photodeposition method, respectively. And these Pd-modified photocatalysts were characterized by X-ray diffraction analysis, X-ray photoelectron spectrum analysis (XPS), UV–Vis diffuse reflectance spectra and temperature programmed desorption (TPD). It was found from XPS results that the dominant oxidation states of Pd on these Pd-modified TiO₂ catalysts were Pd²⁺, PdO, and Pd⁰, respectively. NO-TPD results showed that the NO adsorption capacity was improved greatly by the modification of Pd²⁺ ions. The activity tests showed that Pd-modified TiO₂ by a wet impregnation method increased photocatalytic activity compared to pure TiO₂ (Degussa P25). It was concluded that Pd²⁺ ions on as-prepared TiO₂ catalysts provided key contributions to the improvement of photocatalytic activity. However, Pd⁰ and PdO deposits on TiO₂ almost had no positive effect on NO oxidation. The mechanism of photocatalytic oxidation of NO in gas phase over Pd-modified TiO₂ was also proposed.     

The preparation of Zn2+-doped TiO(2) nanoparticles by sol-gel and solid phase reaction methods respectively and their photocatalytic activities

The photocatalytic oxidation of the organic pollutants with TiO(2) as photocatalyst has been widely studied in the world, and many achievements have been made. The degradation of pollutants is highly related to the photocatalytic activity of TiO(2). It is demonstrated that doping ions to TiO(2) is one way to enhance the photocatalytic activity of TiO(2). In this paper, Zn(2+)-doped TiO(2) nanoparticles were prepared through sol-gel and solid phase reaction methods, characterized by means of X-ray diffraction (XRD) and transmission electron microscopy (TEM). The photocatalytic activity of the elaborated powders was studied following the degradation of Rhodamine B. The results showed that the photocatalytic activity of Zn(2+)-doped TiO(2) prepared by sol-gel method is close to that of pure TiO(2) particles, however, the photocatalytic activity of Zn(2+)-doped TiO(2) prepared by solid phase reaction method is much higher than that of pure TiO(2) particles. The most efficient degradation of Rhodamine B was found with TiO(2) particles doped with 0.5% Zn(2+) in mole and calcined at 500 degrees C. Also the reason for the enhancement of the photocatalytic activity of TiO(2) by Zn(2+) doping through solid phase reaction method was discussed.     

H2O和SO2对V2O5-WO3/TiO2催化剂催化氧化NO的影响

研究了在120℃的反应温度下,H2O和SO2对V2O5-WO3/TiO2催化剂选择性催化氧化（SCO）NO的影响。结果表明,在H2O和SO2存在的情况下催化剂失活很快,停止通入H2O和SO2后活性不能恢复,但在加热到250℃后催化活性基本恢复。FT-IR分析表明,催化剂表面形成了金属硝酸盐和Ti的硫酸盐,对催化活性有一定影响,但不影响催化剂在250℃下催化活性的恢复。SO2、H2O和NO的竞争吸附与SO2和NO2的铅室反应是影响催化剂活性的主要原因。     

Characterization and reactivity of natural manganese ore catalysts in the selective catalytic oxidation of ammonia to nitrogen

Natural manganese ore (NMO) catalysts were characterized and tested in the selective catalytic oxidation of ammonia to nitrogen oxides under dilute conditions. Also, the oxidation of ammonia (NH(3)) was carried out using pure MnO(2), Mn(2)O(3) for comparing with the activity. It is found that the activity of NMO was similar to that of MnO(2) at low temperature below 150 degrees C but above this temperature, the activity of these catalysts showed the difference. In the course of NH(3) oxidation, N(2), NO, N(2)O and H(2)O were produced. But the quantity of NO(2) produced in this experiment was negligible. At temperature below 250 degrees C, selectivity into N(2) from NH(3) oxidation was in the order, NMO > MnO(2) > Mn(2)O(3). This is the reverse of activity of these manganese oxides. Also the characterization of NH(3) oxidation was proposed and supported by the effect of space velocity, inlet O(2) and NH(3) concentration. The increase of space velocity remarkably influenced not only the conversion but also selectivity into N(2). The higher the reaction temperature was, the higher the effect of inlet O(2) and NH(3) concentration on the reaction rate was. By introducing NO during NH(3) oxidation reaction, the possibility of NMO as selective catalytic reduction catalyst at low temperature was studied and showed positive results.     

Fe (III) supported on resin as effective catalyst for the heterogeneous oxidation of phenol in aqueous solution

FeIII supported on resin as an effective catalyst for oxidation was prepared and applied for the degradation of aqueous phenol. Phenol was selected as a model pollutant and the catalytic oxidation was carried out in a batch reactor using hydrogen peroxide as the oxidant. The influent factors on oxidation, such as catalyst dosage, H2O2 concentration, pH, and phenol concentration were examined by considering both phenol conversion and chemical oxygen demand (COD) removal. The FeIII-resin catalyst possesses a high oxidation activity for phenol degradation in aqueous solution. The experimental results of this study show that almost 100% phenol conversion and over 80% COD removal can be achieved with the FeIII-resin catalyst catalytic oxidation system. A series of prepared resin were investigated for improving the oxidation efficiency. It was found that the reaction temperature and initial pH in solution significantly affected both of phenol conversion and COD removal efficiency. The activity of the catalyst significantly decreased at high pH, which was similar to the Fenton-like reaction mechanism. Results in this study indicate that the FeIII-resin catalytic oxidation process is an efficient method for the treatment of phenolic wastewater.     

Removal of ammonia solutions used in catalytic wet oxidation processes

Ammonia (NH(3)) is an important product used in the chemical industry, and is common place in industrial wastewater. Industrial wastewater containing ammonia is generally either toxic or has concentrations or temperatures such that direct biological treatment is unfeasible. This investigation used aqueous solutions containing more of ammonia for catalytic liquid-phase oxidation in a trickle-bed reactor (TBR) based on Cu/La/Ce composite catalysts, prepared by co-precipitation of Cu(NO(3))(2), La(NO(3))(2), and Ce(NO(3))(3) at 7:2:1 molar concentrations. The experimental results indicated that the ammonia conversion of the wet oxidation in the presence of the Cu/La/Ce composite catalysts was determined by the Cu/La/Ce catalyst. Minimal ammonia was removed from the solution by the wet oxidation in the absence of any catalyst, while approximately 91% ammonia removal was achieved by wet oxidation over the Cu/La/Ce catalyst at 230 degrees C with oxygen partial pressure of 2.0 MPa. Furthermore, the effluent streams were conducted at a liquid hourly space velocity of under 9 h(-1) in the wet catalytic processes, and a reaction pathway was found linking the oxidizing ammonia to nitric oxide, nitrogen and water. The solution contained by-products, including nitrates and nitrites. Nitrite selectivity was minimized and ammonia removal maximized when the feed ammonia solution had a pH of around 12.0.     

Effect of the Mn oxidation state and lattice oxygen in Mn-based TiO2 catalysts on the low-temperature selective catalytic reduction of NO by NH3

TiO₂-supported manganese oxide catalysts formed using different calcination temperatures were prepared by using the wet-impregnation method and were investigated for their activity in the low-temperature selective catalytic reduction (SCR) of NO by NH₃ with respect to the Mn valence and lattice oxygen behavior. The surface and bulk properties of these catalysts were examined using Brunauer-Emmett-Teller (BET) surface area, X-ray diffraction (XRD), temperature-programmed reduction (TPR), and temperature-programmed desorption (TPD). Catalysts prepared using lower calcination temperatures, which contained Mn⁴⁺, displayed high SCR activity at low temperatures and possessed several acid sites and active oxygen. The TPD analysis determined that the Brönsted and Lewis acid sites in the Mn/TiO₂ catalysts were important for the low-temperature SCR at 80～160 and 200～350 °C, respectively. In addition, the available lattice oxygen was important for attaining high NO to NO₂ oxidation at low temperatures.

Implications: Recently, various Mn catalysts have been evaluated as SCR catalysts. However, there have been no studies on the relationship of adsorption and desorption properties and behavior of lattice oxygen according to the valence state for manganese oxides (MnO_x). Therefore, in this study, the catalysts were prepared by the wet-impregnation method at different calcination temperatures in order to show the difference of manganese oxidation state. These catalysts were then characterized using various physicochemical techniques, including BET, XRD, TPR, and TPD, to understand the structure, oxidation state, redox properties, and adsorption and desorption properties of the Mn/TiO₂ catalysts.     

Aromatic photonitration in homogeneous and heterogeneous aqueous systems

This work describes the nitration of aromatics upon near-UV photolysis of nitrate and nitrite in aqueous solution and upon photocatalytic oxidation of nitrite in TiO2 suspensions. Phenol is used in this work as a model aromatic molecule and as a probe for *NO2/N2O4. The photoinduced nitration of phenol in aqueous systems occurs upon the reaction between phenol and *NO2 or N2O4, and is enhanced by the photocatalytic oxidation of nitrite to *NO2 by TiO2. Aromatic photonitration in the liquid phase can play a relevant role in the formation of nitroaromatics in natural waters and atmospheric hydrometeors, thus being a potential pathway for the condensed-phase nitration of aromatics. Furthermore, the photoinduced oxidation of nitrite to nitrogen dioxide suggests a completely new role for nitrite in natural waters and atmospheric aerosols.     

Enhanced photoelectrocatalytic performance of Zn-doped WO(3) photocatalysts for nitrite ions degradation under visible light

WO(3) and Zn-doped WO(3) thin films were prepared on indium-tin oxide glass by a dip-coating. The composite films were characterized by UV-Vis absorption spectra, X-ray diffraction and scanning electron microscope. The effect of preparation conditions (concentration of Zn, annealing temperature, number of layers) on the photocurrent was studied. It was found that the photocurrent under visible light displayed the highest value for 2% Zn-WO(3) films annealed at 400 degrees C. The photocatalytic activity of the Zn-doped WO(3) was evaluated in terms of decay rate of nitrite ions under visible light. The influence of applied potential, initial pH and nitrite concentration on the reaction rate was studied. The experiments demonstrated that NO(2)(-) could be efficiently degraded on the doped photoanode that showed a higher activity than the undoped WO(3) especially under high anodic potential (>0.7 V). The rate of degradation was enhanced in aqueous NaCl solutions. Furthermore, it was demonstrated that the photodegradation mechanism of NO(2)(-) proceeded mainly indirectly via OH radicals. The possible reason of enhancement of reaction rate was also discussed.     

Ni/Fe-supported over hydrotalcites precursors as catalysts for clean and selective oxidation of Basic Yellow 11: Reaction intermediates determination

In this work, Basic Yellow 11 (BY 11) was employed as model compound to study catalytic wet air oxidation as a pre-treatment step to the conventional biological oxidation. Ni and Fe catalysts supported over hydrotalcite (HT) were prepared by incipient wetness and excess impregnation to obtain catalysts with different metal loadings (from 1 to 10 wt.%). HTs were synthesized by co-precipitation and characterized with XRD, X-ray fluorescence (XRF), BET, thermogravimetric analysis and SEM. Results showed that dye conversion increased with Ni and Fe content up to 7 wt.% and that the most effective catalyst were prepared by incipient wetness impregnation. The influence of metal loading in the catalyst, and the preparation method as well as the reaction conditions was investigated. A mechanism and reaction pathways for BY 11 during catalytic liquid phase oxidation have also been proposed.