Phanerochaete chrysosporium吸附载体的选择及染料降解研究

研究了游离细胞与载体吸附培养、不同载体材料对Phanerochaete chrysosporium进行连续染料脱色及产酶能力的影响。结果表明,P.chrysosporium可在载体上良好生长,甚至生长到载体内部。木屑、玉米芯、花生壳3种载体材料中,以木屑载体吸附培养物的持续脱色和产酶效果最佳,该培养物经三轮连续脱色后对染料RB5仍能达到最高95%的脱色率,并产生596 U/L锰依赖过氧化物酶（MnP）和1 326 U/L木质素过氧化物酶（LiP）,对染料的持续脱色和产酶能力明显优于游离细胞培养物。     

载体吸附培养黄孢原毛平革菌(Phanerochaete chrysosporium)和云芝(Trametes versicolor)对染料的脱色

比较研究了不同载体吸附培养的黄孢原毛平革菌(Phanerochaete chrysosporium)和云芝(Trametes versicolor)对染料连续脱色的效果。结果表明:(1)白腐真菌黄孢原毛平革菌和云芝分别在含有球形的木屑、玉米芯和花生壳载体的液体环境中振荡培养,菌体以膜状或团状形式大量附着生长在载体表面。(2)连续4轮脱色过程中,不论黄孢原毛平革菌还是云芝,都是木屑为载体的培养液的持续脱色和产酶能力最好,宜选择木屑为载体。其中,木屑为载体的黄孢原毛平革菌培养液经过2轮连续12d脱色后对活性黑RB5的最高脱色率仍能达到97%,在第3轮脱色中对活性红M-3BE的最终脱色率接近96%,并且能产生最高611U/L的锰依赖过氧化物酶(MnP)和1 477U/L的木质素过氧化物酶(LiP)。(3)在实际应用中应该将木屑为载体的黄孢原毛平革菌和云芝培养液都投加到含染料废水处理系统中,强化生物处理效果。     

漆酶对活性黑KN-B和直接大红染料的脱色性能

利用白腐真菌漆酶对活性黑KN-B和直接大红2种偶氮染料进行脱色实验。考察反应时间、加酶量、pH值、染料浓度、温度对脱色率的影响，研究了ABTS介体以及金属离子存在下的脱色效果，并分析了漆酶脱色的动力学性能以及其对偶氮染料的降解规律。结果表明，活性黑KN-B和直接大红脱色适宜条件为：反应时间为30 min，加酶量8 U/mL，pH=7，染料浓度分别为50 mg/L和80 mg/L，温度40~45℃。ABTS介体对酶促偶氮染料脱色没有明显促进作用。Fe²⁺对漆酶脱色有较强的抑制作用；Cu²⁺对漆酶催化活性黑KN-B促进作用较大，对直接大红影响较小。漆酶对2种染料的脱色反应符合米氏方程，其催化活性黑KN-B和直接大红染料的K_m值分别为114.81 mg/L，317.5 mg/L，v_max值分别为6.57 mg/（L·min）和26.0 mg/（L·min）。     

突变灰盖鬼伞过氧化物酶降解刚果红的响应面法优化分析简

酶法降解偶氮染料刚果红是一个复杂的过程，受温度、pH、酶量、刚果红浓度和双氧水浓度显著影响。为研究各因素及因素间交互作用对刚果红降解影响，提高刚果红的降解率，分别使用单因素法和响应面分析法对刚果红降解条件进行了优化。单因素实验结果显示灰盖鬼伞过氧化物酶降解刚果红的最适条件为：pH 5.0、32℃、酶量4.98 U、双氧水0.1 mmol/L、刚果红20 mg/L，此时刚果红最高降解率为34.84%。然后选双氧水浓度、刚果红浓度和灰盖鬼伞过氧化物酶量作为3个因素，通过中心组合设计实验，用响应面法对刚果红降解进行优化分析，最后得到一个拟合度良好的二次多项方程模型（R²=0.9900）。方差分析结果显示，刚果红浓度和酶量是影响最显著的因素，双氧水与酶以及染料与酶之间的交互作用极显著。响应面分析优化后的反应体系为：双氧水浓度0.15 mmol/L，刚果红浓度为27.21 mg/L，酶为2.0 7 U，在此条件下，刚果红降解率达58.13%。     

厌氧污泥对间二氯苯的吸附性能简

为了研究灭活厌氧污泥和活性厌氧污泥对间二氯苯 （m-DCB）的吸附，考察了吸附平衡时间、吸附动力学、吸附等温线、吸附热力学、污泥投加量和pH对吸附m-DCB的影响。结果表明，2种污泥对m-DCB的吸附在1 h内达到平衡。应用伪一级、伪二级反应动力学对实验数据进行验证，表明厌氧污泥吸附m-DCB更符合伪二级反应动力学模型。2种污泥对m-DCB的吸附都可以用Langmuir和Freundlich吸附模型拟合，但Langmuir吸附模型的拟合结果要好于Freundlich模型，且活性厌氧污泥的吸附性能显著高于灭活厌氧污泥。从吸附热力学上看，该吸附为放热反应，低温有利于吸附反应的进行。pH值对2种污泥吸附m-DCB的影响很小。     

漆酶对活性艳蓝染料废水脱色

用白腐真菌漆酶对活性艳蓝X-BR和活性艳蓝K-NR 2种活性染料进行脱色实验。研究了pH、温度、染料浓度和酶活力对脱色率的影响。结果表明,漆酶脱色的适宜条件为:反应温度45℃,pH 6～7,适宜染料浓度为50 mg/L,酶浓度5 U/mL,反应1 h两种染料脱色率可达到75%;通过正交实验确定2种染料的最佳脱色组合分别为:反应温度55℃、pH7、活性艳蓝X-BR浓度50 mg/L、酶浓度5 U/mL和反应温度55℃、pH 6、活性艳蓝K-NR浓度50 mg/L、酶浓度5 U/mL。在所得最优条件下反应1 h,活性艳蓝X-BR和活性艳蓝K-NR的脱色率分别为74.2%和78.6%;反应2 h,脱色率分别为78%和79.5%。     

蠕虫L.variegatus在污泥减量中的作用与应用前景分析

剩余污泥已成为污水处理厂亟待解决的棘手问题。虽然现有污泥减量技术众多，但或多或少都存在着技术或经济上的不足。蠕虫——L.variegatus应用于污泥减量具有较好的实际效果以及潜在的商业利用价值，因此，近年来受到人们关注。首先，介绍L.variegatus一般习性、对污泥减量的试验效果。然后，对L.variegatus应用于大规模连续系统的要点进行了技术分析。最后，对L.variegatus应用于实际污水处理厂污泥减量的技术与经济的合理性进行分析和估算。     

胺基化磁性壳聚糖微球固定化Candida tropicalis处理含酚废水研究

通过戊二醛将Candida tropicalis固定在胺基化磁性壳聚糖微球（NH₂-M-CSm）上，探讨了游离Ct、磁性壳聚糖微球（M-CSm)固定化Ct和NH₂-M-CSm固定化Ct除酚的最适条件。结果表明，游离Ct最适pH为5.5，M-CSm和NH₂-M-CSm固定化Ct均在4~6之间；游离Ct最适温度为35℃，M-CSm和NH₂-M-CSm固定化Ct均为30℃；NH₂-M-CSm固定化Ct的热稳定性＞M-CSm固定化Ct＞游离Ct；离子强度对固定化Ct无影响，而对游离Ct有一定的影响；一价态离子对游离Ct和固定化Ct影响不大；二价态离子对游离Ct起抑制作用，而对固定化Ct起促进作用；三价态离子对游离Ct和固定化Ct均起抑制作用。通过实验还得知，固定化Ct可以通过再培养恢复酶活力，其半衰期至少为90 d。最后，在实际废水处理中，经3 h反应后，NH₂-M-CSm固定化Ct除酚几乎达100%，而游离Ct只达到80%左右。     

不同培养条件下锰过氧化物酶(MnP)的合成及其对甲基橙的降解

高效、大规模、低成本合成木质素降解酶是直接采用其降解难降解有机污染物所必须解决的问题.对锰过氧化物酶(MnP)降解甲基橙和在非灭菌的反应器中连续合成MnP的可行性进行考察.结果表明,在采用2 mmol H2O2和1.5 mmol MnSO4的降解体系中,获最大脱色效果,且100、200和300 U/L的MnP可在8h内将甲基橙分别脱色18％、23％和35％;在非灭菌的反应器水平上实现了固定化培养的P.chrysosporium连续23 d合成MnP,但MnP酶活仅为2～ 23 U/L,难以酶解甲基橙;然而,在摇瓶培养条件下固定化的P.chrysosporium合成的MnP却能达1 152 U/L.因此,直接采用MnP对污染物进行降解以及在非灭菌的反应器中持续合成MnP是可行的,但就在非灭菌条件下如何提高MnP的合成量还有待开展深入的研究.     

仿生矿化法制备壳聚糖/纳米CdS复合粒子对猩红B光催化降解研究

用仿生矿化法制备了壳聚糖/纳米CdS复合粒子，并用于可见光光催化降解猩红B染料模拟废水，系统地研究了染料初始浓度、pH值、催化剂投加量、光照情况和催化剂重复使用等因素对猩红B的光解脱色效率的影响。结果表明，当pH=3.0，催化剂投加量为0.7 g/L的条件下，对初始溶液为20 mg/L的猩红B模拟废水，60 min之内脱色率超过96%。酸性媒介比碱性媒介更有利于猩红B染料光解脱色。实验范围内Br^-、NO^-₃和Cl^-等无机阴离子，均对降解脱色有促进作用，其中NO₃^-对脱色作用促进最显著。处理前后的UV-Vis谱图分析表明猩红B在壳聚糖/纳米CdS复合粒子可见光光解处理过程中脱色是因为染料发生氧化光降作用。催化剂重复利用5次后，处理60 min对猩红B的脱色率仍可达到80.7%。     

基于人工神经网络和遗传算法研究锰过氧化酶脱色甲基橙

基于锰过氧化物酶(MnP)氧化脱色偶氮类染料的原理,实验研究MnP对甲基橙的脱色工艺,采用人工神经网络(ANN)和遗传算法(GA)建立脱色模型并优化工艺。建立的ANN模型的误差、相关系数、均方根误差和绝对平均偏差分别为0.0009、0.9971、1.21和6.82,模型有效且能够用于预测和工艺优化。采用GA对ANN模型进行数值寻优,得到的最佳工艺条件为酶液量0.6 mL,Mn2+浓度4 mmol/L,H2O2浓度0.49 mmol/L。该条件下脱色率达到(90.74±0.59)%。ANN耦合GA有效地建立了锰过氧化物酶脱色甲基橙的模型,并优化了工艺参数,为甲基橙脱色的研究提供一定参考。     

Use of fungi for the bioconversion of rice straw into cellulase enzyme

Cellulase production was carried out by solid state bioconversion (SSB) method using rice straw, a lignocellulosic material and agricultural waste, as the substrate of three Trichoderma spp. and Phanerochaete chrysosporium in lab-scale experiments. The results were compared to select the best fungi among them for the production of cellulase. Phanerochaete chrysosporium was found to be the best among these species of fungi, which produced the highest cellulase enzyme of 1.43 IU/mL of filter paper activity (FPase) and 2.40 IU/mL of carboxymethylcellulose activity (CMCase). The “glucosamine” and “reducing sugar” parameters were observed to evaluate the growth and substrate utilization in the experiments. In the case of Phanerochaete Chrysosporium, the highest glucosamine concentration was 1.60 g/L and a high concentration of the release of reducing sugar was measured as 2.58 g/L obtained on the 4th day of fermentation. The pH values were also recorded. The range of the pH was about 5.15 to 5.56 in the case of Phanerochaete Chrysosporium.     

Decolorization of palm oil mill effluent using growing cultures of Curvularia clavata

Agricultural wastewater that produces color are of environmental and health concern as colored effluent can produce toxic and carcinogenic by-products. From this study, batch culture optimization using response surface methods indicated that the fungus isolated from the pineapple solid waste, Curvularia clavata was able to decolorize sterile palm oil mill effluent (POME) which is mainly associated with polyphenol and lignin. Results showed successful decolorization of POME up to 80 % (initial ADMI [American Dye Manufacturing Index] of 3,793) with 54 % contributed by biosorption and 46 % by biodegradation after 5 days of treatment. Analysis using HPLC and GC-MS showed the degradation of color causing compound such as 3-methoxyphenyl isothiocynate and the production of new metabolites. Ecotoxicity test indicated that the decolorized effluent is safe for discharge. To determine the longevity of the fungus for a prolonged decolorization period, sequential batch decolorization studies were carried out. The results showed that lignin peroxidase and laccase were the main ligninolytic enzymes involved in the degradation of color. Carboxymethyl cellulase (CMCase) and xylanase activities were also detected suggesting possible roles of the enzymes in promoting growth of the fungus which consequently contributed to improved decolorization of POME. In conclusion, the ability of C. clavata in treating color of POME indicated that C. clavata is of potential use for decolorization and degradation of agricultural wastewater containing polyphenolic compounds.     

Highly efficient decolorization of Malachite Green by a novel Micrococcus sp. strain BD15

Purpose

Malachite Green (MG) is used for a variety of applications but is also known to be carcinogenic and mutagenic. In this study, a novel Micrococcus sp. (strain BD15) was observed to efficiently decolorize MG. The purposes of this study were to explore the optimal conditions for decolorization and to evaluate the potential use of this strain for MG decolorization.

Methods

Optical microscope and UV?Cvisible analyses were carried out to determine whether the decolorization was due to biosorption or biodegradation. A Plackett?CBurman design was employed to investigate the effect of various parameters on decolorization, and response surface methodology was then used to explore the optimal decolorization conditions. Kinetics analysis and antimicrobial activity tests were also performed.

Results

The results indicated that the decolorization by the strain was mainly due to biodegradation. Concentrations of MG, urea, and yeast extract and inoculum size had significantly positive effects on MG decolorization, while concentrations of CuCl₂ and MgCl₂, and temperature had significantly negative effects. The interaction between different parameters could significantly affect decolorization, and the optimal conditions for decolorization were 1.0 g/L urea, 0.9 g/L yeast extract, 100 mg/L MG, 0.1 g/L inoculums (dry weight), and incubation at 25.2°C. Under the optimal conditions, 96.9% of MG was removed by the strain within 1 h, which represents highly efficient microbial decolorization. Moreover, the kinetic data for decolorization fit a second-order model well, and the strain showed a good MG detoxification capability.

Conclusion

Based on the results of this study, we propose Micrococcus sp. strain BD15 as an excellent candidate strain for MG removal from wastewater.     

天然沸石负载La2O3-ZnO-TiO2光催化降解活性艳红K-2BP

利用80目天然斜发沸石作载体制备La₂O₃(0.5%)-ZnO(20%)-TiO₂/沸石复合光催化剂，以20 W紫外灯为光源，在自制的光催化反应器中降解活性艳红K-2BP，考察了光照时间、空气通入量、催化剂用量、溶液初始浓度、H₂O₂与Fe³⁺投加量等对活性艳红K-2BP光催化降解率的影响。结果表明，当溶液初始浓度为60 mg/L，催化剂投加量为12 g/L，通气量为1 200 mL/min，光照2.5 h，活性艳红K-2BP的降解率可达99.2%；H₂O₂和Fe³⁺投加量为4 mL/L和3 g/L时，光照1 h活性艳红K-2BP降解率分别为100%和97.2%。紫外可见吸收光谱显示，LZTZ光催化剂可有效降解印染废水。     

二鼠李糖脂对白腐菌降解稻草中木质纤维素的影响

通过固态发酵方式采用白腐菌对稻草中木质纤维素进行降解,并研究了生物表面活性剂二鼠李糖脂对该降解过程的影响。结果表明,不同浓度的二鼠李糖脂能在不同程度上提高降解过程水溶性有机碳的含量,添加0.007%和0.021%二鼠李糖脂的实验组最高TOC(total organic carbon)浓度较对照组分别提高了83.6%和54.5%,这有利于黄孢原毛平革菌的生长,且延缓了菌体的衰退。添加临界胶束浓度0.007%和0.021%浓度的二鼠李糖脂可使LiP(lignin peroxidase)酶活分别提高85.7%和41.2%,二鼠李糖脂对MnP(manganese peroxidase)酶活没有显著影响。生物表面活性剂的介入促进了白腐菌对稻草中木质素的降解,添加0.007%二鼠李糖脂可使木质素降解率提高54%。     

Decolouration of azo dyes by <Emphasis Type="Italic">Phanerochaete chrysosporium</Emphasis> immobilised into alginate beads

Background, aim and scope  

Because of high discharged volumes and effluent composition, wastewater from the textile industry can be considered as the most polluting amongst all industrial sectors, thus greatly requiring appropriate treatment technologies. Although some abiotic methods for the reduction of several dyes exist, these require highly expensive catalysts and reagents. Biotechnological approaches were proven to be potentially effective in the treatment of this pollution source in an eco-efficient manner. The white-rot fungi are, so far, the most efficient microorganisms in degrading synthetic dyes. This white-rot fungi’s property is due to the production of extracellular lignin-modifying enzymes, which are able to degrade a wide range of xenobiotic compounds because of their low substrate specificity. In this paper, we studied the ability of the white-rot fungus Phanerochaete chrysosporium immobilised into Ca-alginate beads to decolourise different recalcitrant azo dyes such as Direct Violet 51 (DV), Reactive Black 5 (RB), Ponceau Xylidine (PX) and Bismark Brown R (BB) in successive batch cultures. To the best of our knowledge, this is the first study on the immobilisation of P. chrysosporium into Ca-alginate beads for its application in dye decolouration.     

高压电弧放电处理偶氮染料废水

用高压电弧放电产生的低温等离子体对含偶氮染料的废水进行了处理，以甲基橙为例研究了电压幅值、处理时间、溶液初始浓度、溶液初始pH值、投加Fe^2＋和Fe^3＋对染料脱色的影响。实验结果表明，甲基橙浓度为50mg／L时其降解率随时间和电压幅值的增加而增加。溶液初始浓度对染料去除效果影响较为明显，同等条件下初始浓度越低降解率越高。酸性条件下有利于低温等离子体处理甲基橙。Fe^2＋和Fe^3＋对低温等离子体降解甲基橙有一定的催化作用。电压8kV处理3min，Fe^2＋为20mg／L时去除率由89．64％增至99．72％。Fe2（SO4），的最佳投加量为5mg／L（以Fe^3＋计），而FeCl，的最佳投加量为80mg／L（以Fe^3＋计）。     

Batch and continuous biodegradation of Amaranth in plain distilled water by P. aeruginosa BCH and toxicological scrutiny using oxidative stress studies

Bacterium Pseudomonas aeruginosa BCH was able to degrade naphthylaminesulfonic azo dye Amaranth in plain distilled water within 6 h at 50 mg?l^?1 dye concentration. Studies were carried out to find the optimum physical conditions and which came out to be pH?7 and temperature 30 °C. Amaranth could also be decolorized at concentration 500 mg?l^?1. Presence of Zn and Hg ions could strongly slow down the decolorization process, whereas decolorization progressed rapidly in presence of Mn. Decolorization rate was increased with increasing cell mass. Induction in intracellular and extracellular activities of tyrosinase and NADH-DCIP reductase along with intracellular laccase and veratryl alcohol oxidase indicated their co-ordinate action during dye biodegradation. Up-flow bioreactor studies with alginate immobilized cells proved the capability of strain to degrade Amaranth in continuous process at 20 ml?h^?1 flow rate. Various analytical studies viz.—HPLC, HPTLC, and FTIR gave the confirmation that decolorization was due to biodegradation. From GC-MS analysis, various metabolites were detected, and possible degradation pathway was predicted. Toxicity studies carried out with Allium cepa L. through the assessment of various antioxidant enzymes viz. sulphur oxide dismutase, guaiacol peroxidase, and catalase along with estimation of lipid peroxidation and protein oxidation levels conclusively demonstrated that oxidative stress was generated by Amaranth.