PCDD/F formation from oxy-PAH precursors in waste incinerator flyash

The yield of PCDD/F in relation to the presence of oxygenated PAH in model waste incinerator flyash has been investigated in a fixed bed laboratory scale reactor. Experiments were undertaken by thermal treatment of the model flyash at 250 and 350 °C under a simulated flue gas stream for 2 h. After reaction, the PCDD/F content of the reacted flyash and the PCDD/F released into the exhaust gas, and subsequently trapped by XAD-II resin in a down-stream condensation system were analyzed. The PAHs investigated were, dibenzofuran and benzo[b]naphtho[2,3-d]furan and were spiked onto the model flyash as reactant precursors for PCDD/F formation. The results showed significant formation of furans from both of the PAH investigated, however except from some highly chlorinated dioxin congeners, the formation of dioxins was not so common. Benzonaphthofuran was significantly more reactive than dibenzofuran in PCDD/F formation, in spite of the fact that dibenzofuran is structurally more similar to that of PCDD/F. Thus, there was no clear attribution between the chemical structure of PAH used and the formation of PCDD/F. There were considerable differences between the yields of PCDD/F congeners in the gaseous species and those in the reacted flyash under the same operational conditions. The concentration of PCDD/Fs was reduced at the higher reaction temperature of 350 °C; however, the higher temperature resulted in the majority of the PCDD/F formed on the flyash being released into the gas phase.     

Atmospheric deposition of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) in Guangzhou,China

Atmospheric deposition of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) was investigated at four locations, namely at Yuancun, Wushan, Haizhu and Changban in Guangzhou City, Guangdong Province. The annual deposition fluxes of tetra- to octa-CDD/Fs (total PCDD/Fs) were found to range from 170 to 3000 (mean 1500) pg m⁻² day⁻¹, and the fluxes of total 2, 3, 7, 8-substituted PCDD/F congeners ranged from 2.1 to 41 (mean 20) pg WHO-TEQ m⁻² day⁻¹ at Wushan. The average deposition fluxes of total 2, 3, 7, 8-substituted PCDD/F congeners in rainy season were found to be 37, 27 and 28 pg WHO-TEQ m⁻² day⁻¹ at Yuancun, Haizhu and Changban, respectively, and the PCDD/F deposition fluxes behaved obviously higher in rainy season than in dry season. Results from regression analysis showed that number of rainy days, the amount of wet precipitation, PCDD/F concentrations in particles and organic carbon content played important roles in the variation of PCDD/F deposition fluxes. Monthly average temperatures change little over the year. Therefore, it only played a minor role in monthly variation of PCDD/F deposition fluxes. Particle deposition fluxes were generally not considered as the factor that could cause the differences in PCDD/F deposition fluxes between rainy and dry season, but were found to be related with PCDD/F deposition fluxes in rainy season or dry season. It was found that the profiles of PCDD/F homologs or congeners in the samples were the same either spatially or temporally, indicating that the PCDD/F emission sources were similar to one another. The similarities in PCDD/F homolog patterns and the differences in deposition fluxes between samples collected from heavy-traffic roadside and nearby residence house roof indicated that vehicle exhaust might be an important source for PCDD/F in Guangzhou. PCDD/F concentrations and profiles of PCDD/F homologs in atmospheric deposition were compared with those in both total suspended particles in air and soils, and conclusions indicated that atmospheric deposition possibly tended to remove lower-chlorinated DD/Fs from air and was one of sources for PCDD/Fs in soils.     

Emissions of PCDD/Fs,PCBs, and PAHs from legacy on-road heavy-duty diesel engines

Exhaust emissions of seventeen 2,3,7,8-substituted polychlorinated dibenzo-p-dioxin/furan (PCDD/F) congeners, tetra–octa PCDD/F homologues, 12 WHO 2005 polychlorinated biphenyl (PCB) congeners, mono–nona chlorinated biphenyl homologues, and 19 polycyclic aromatic hydrocarbons (PAHs) from three legacy diesel engines were investigated. The three engines tested were a 1985 model year GM 6.2 J-series engine, a 1987 model year Detroit Diesel Corporation 6V92 engine, and a 1993 model year Cummins L10 engine. Results were compared to United States’ mobile source inventory for on-road diesel engines, as well as historic and modern diesel engine emission values. The test fuel contained chlorine at 9.8 ppm which is 1.5 orders of magnitude above what is found in current diesel fuel and 3900 ppm sulfur to simulate fuels that would have been available when these engines were produced. Results indicate PCDD/F emissions of 13.1, 7.1, and 13.6 pg International Toxic Equivalency (I-TEQ) L⁻¹ fuel consumed for the three engines respectively, where non-detects are equal to zero. This compares with a United States’ mobile source on-road diesel engine inventory value of 946 pg I-TEQ L⁻¹ fuel consumed and 1.28 pg I-TEQ L⁻¹ fuel consumed for modern engines equipped with a catalyzed diesel particle filter and urea selective catalytic reduction. PCB emissions are 2 orders of magnitude greater than modern diesel engines. PAH results are representative of engines from this era based on historical values and are 3–4 orders of magnitude greater than modern diesel engines.     

Dioxins,furans and polycyclic aromatic hydrocarbons emissions from a hospital and cemetery waste incinerator

An experimental campaign was carried out on a hospital and cemetery waste incineration plant in order to assess the emissions of polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs) and polycyclic aromatic hydrocarbons (PAHs). Raw gases were sampled in the afterburning chamber, using a specifically designed device, after the heat recovery section and at the stack. Samples of slags from the combustion chamber and fly ashes from the bag filter were also collected and analyzed. PCDD/Fs and PAHs concentrations in exhaust gas after the heat exchanger (200–350 °C) decreased in comparison with the values detected in the afterburning chamber. Pollutant mass balance regarding the heat exchanger did not confirm literature findings about the de novo synthesis of PCDD/Fs in the heat exchange process. In spite of a consistent reduction of PCDD/Fs in the flue gas treatment system (from 77% up to 98%), the limit of 0.1 ng ITEQ Nm⁻³ at the stack was not accomplished. PCDD/Fs emission factors for air spanned from 2.3 up to 44 μg ITEQ t⁻¹ of burned waste, whereas those through solid residues (mainly fly ashes) were in the range 41–3700 μg ITEQ t⁻¹. Tests run with cemetery wastes generally showed lower PCDD/F emission factors than those with hospital wastes. PAH total emission factors (91–414 μg kg⁻¹ of burned waste) were in the range of values reported for incineration of municipal and industrial wastes. In spite of the observed release from the scrubber, carcinogenic PAHs concentrations at the stack (0.018–0.5 μg Nm⁻³) were below the Italian limit of 10 μg Nm⁻³.     

Identifying source regions for the atmospheric input of PCDD/Fs to the Baltic Sea

PCDD/F contamination of the Baltic Sea has resulted in the European Union imposing restrictions on the marketing of several fish species. Atmospheric deposition is the major source of PCDD/Fs to the Baltic Sea, and hence there is a need to identify the source regions of the PCDD/Fs in ambient air over the Baltic Sea. A novel monitoring strategy was employed to address this question. During the winter of 2006–2007 air samples were collected in Aspvreten (southern Sweden) and Pallas (northern Finland). Short sampling times (24 h) were employed and only samples with stable air mass back trajectories were selected for analysis of the 2,3,7,8-substituted PCDD/F congeners. The range in the PCDD/F concentrations from 40 samples collected at Aspvreten was a factor of almost 50 (range 0.6–29 fg TEQ/m³). When the samples were grouped according to air mass origin into seven compass sectors, the variability was much lower (typically less than a factor of 3). This indicates that air mass origin was the primary source of the variability. The contribution of each sector to the PCDD/F contamination over the Baltic Sea during the winter half year of 2006/2007 was calculated from the average PCDD/F concentration for each sector and the frequency with which the air over the Baltic Sea came from that sector. Air masses originating from the south–southwest, south–southeast and east segments contributed 65% of the PCDDs and 75% of the PCDFs. Strong correlations were obtained between the concentrations of most of the PCDD/F congeners and the concentration of soot. These correlations can be used to predict the PCDD/F concentrations during the winter half year from inexpensive soot measurements.     

Atmospheric bulk deposition of dioxin and furans to Danish background areas

Polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) were measured in bulk deposition at three Danish rural forest sites with a mutual maximum distance of 450 km. At one of the forest sites concentrations in the ambient atmosphere were sampled from a 12 m high tower. Sampling was carried out within a period of 3 years with sampling intervals of 1–2 months. Mean bulk deposition fluxes were 1 ng m⁻² yr⁻¹ I-TEQ and deviated less than 30% between the sites. Yearly average PCDD/F concentrations in the atmosphere were 24 fg m⁻³ I-TEQ with maximum values in the winter period. During winter months atmospheric concentrations of PCDD/F and oxidized sulphur compounds showed a positive correlation, furthermore seasonal bulk deposition showed correlation between PCDD/F and sulphate.     

A national inventory to estimate release of polychlorinated dibenzo-p-dioxins and dibenzofurans in Portugal

Taking into account current environmental concerns, the main objective of this work focused a national inventory aiming to estimate the amount of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/PCDF) released in Portugal in 2006. The methodology used was based on the Standardized Toolkit for Identification and Quantification of Dioxins and Furan Releases, developed by UNEP Chemicals, in 2005. The method allows the assessment of the amount of PCDD/PCDF released into the environment along five vectors involving air, water, land, products and residues. Facing some difficulties mainly regarding to the availability of data for some activities known to produce PCDD/PCDF, three scenarios (Sc1 to Sc3) corresponding to lower, central and upper estimates were established. The Sc1 scenario (lower estimate) includes the situations where in case of doubt or scarce information, reduced or none emission values were assumed, Sc2 refers to a central estimate, which is believed to be the most realistic for the Portuguese situation, while Sc3 corresponds to the worst case (upper estimate). The results obtained pointed out that the total amount of PCDD/PCDF emitted in Portugal during the period under analysis was in the range of 51.2–217.9 g TEQ year⁻¹, with the most likely value of 95.2 g TEQ year⁻¹ achieved under the Sc2 scenario. This study also showed that the methodology developed by UNEP Chemicals is a very simple one, and the main difficulty is the availability of data. The main indicators calculated in this study were 8.98 μg TEQ/(year person) by taking into account the total amount of PCDD/PCDF released, and 3.63 μg TEQ/(year person) when only air emissions were considered.     

Assessment of variations in atmospheric PCDD/Fs by Asian dust in Southeastern Korea

Atmospheric concentrations of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) were measured in southeastern Korea during the spring of 2002. During this period, severe Asian dust events (ADs) occurred throughout Korea. Total suspended particulates (TSP) of ADs (456.8 μg m⁻³) increased approximately 3.6-fold compared with non-Asian dust events (NADs; 128.5 μg m⁻³). However, the concentrations of PCDD/Fs (average concentration, 3.34 pg m⁻³) did not increase as much as TSP; there was not a significant difference in the concentrations of particle-bound PCDD/Fs collected between ADs (2.45 pg m⁻³) and NADs (2.05 pg m⁻³). Meanwhile, according to TSP levels, the concentrations during NADs were 2.8-fold higher than ADs (16.73 and 5.98 ng g⁻¹-TSP, respectively). High TSP levels during sand storms without an increase in PCDD/Fs reflected an increase in coarse and accumulation mode particles. Gas/particle partitioning studies revealed the additional inputs of particulate matters to the air during ADs which did not relate with the increase of PCDD/Fs. Furthermore, emissions from ADs may consist of relatively complex atmospheric particles; back trajectories showed air masses moving at low altitudes over Korea, but there were no differences in PCDD/Fs or atmospheric pollutants regardless of air movements. The study area, which is located in southeastern Korea, might be affected by both marine and regional anthropogenic sources, which do not appear to cause clear differences in PCDD/F concentrations or congener profiles between different air trajectories.     

Large PAHs detected in fine particulate matter emitted from light-duty gasoline vehicles

Emission factors of large PAHs with 6–8 aromatic rings with molecular weights (MW) of 300–374 were measured from 16 light-duty gasoline-powered vehicles (LDGV) and one heavy-duty diesel-powered vehicle (HDDV) operated under realistic driving conditions. LDGVs emitted PAH isomers of MW 302, 326, 350, and 374, while the HDDV did not emit these compounds. This suggests that large PAHs may be useful tracers for the source apportionment of gasoline-powered motor vehicle exhaust in the atmosphere. Emission rates of MW 302, 326, and 350 isomers from LDGVs equipped with three-way catalysts (TWCs) ranged from 2 to 10 (μg L⁻¹ fuel burned), while emissions from LDGVs classified as low emission vehicles (LEVs) were almost a factor of 10 lower. MW 374 PAH isomers were not quantified due to the lack of a quantification-grade standard. The reduced emissions associated with the LEVs are likely attributable to improved vapor recovery during the “cold-start” phase of the Federal Test Procedure (FTP) driving cycle before the catalyst reaches operating temperature. Approximately 2 (μg g⁻¹ PM) of MW 326 and 350 PAH isomer groups were found in the National Institute of Standards and Technology standard reference material (SRM)#1649 (Urban Dust). The pattern of the MW 302, 326, and 350 isomers detected in SRM#1649 qualitatively matched the ratio of these compounds detected in the exhaust of TWC LDGVs suggesting that each gram of Urban Dust SRM contained 5–10 mg of PM originally emitted from gasoline-powered motor vehicles.Large PAHs made up 24% of the total LEV PAH emissions and 39% of the TWC PAH emissions released from gasoline-powered motor vehicles. Recent studies have shown certain large PAH isomers have greater toxicity than benzo[a]pyrene. Even though the specific toxicity measurements on PAHs with MW >302 have yet to be performed, the detection of significant amounts of MW 326 and 350 PAHs in motor vehicle exhaust in the current study suggests that these compounds may pose a significant public health risk.     

Desorption of PCDD/PCDF from municipal solid waste incinerator flyash under post-combustion plant conditions

The influence of temperature on the levels of PCDD and PCDF remaining in, and desorbed from, a municipal solid waste incinerator flyash was investigated by heating the ash to between 200 and 400 degrees C under a simulated flue gas for four days reaction time. Considerable desorption of PCDD/PCDF from the flyash was seen at 275 degrees C and above. Maximum desorption occurred at 350 degrees C, with the equivalent of nearly eight times the total PCDD/PCDF concentration of the original flyash being lost to the vapour phase per unit mass of initial flyash. The I-TEQ value of the desorbed PCDD/PCDF was considerable, being over fourteen times that of the original flyash at 325 degrees C. The results indicate that formation of PCDD/PCDF on flyash deposits in the post-combustion plant of incinerators can result in the release of significant amounts of PCDD/PCDF to the flue gas stream.     

Emission factors of PAHs,methoxyphenols, levoglucosan,elemental carbon and organic carbon from simulated wheat and Kentucky bluegrass stubble burns

Emission factors (EFs) of pollutants from post-harvest agricultural burning are required for predicting downwind impacts of smoke and inventorying emissions. EFs of polycyclic aromatic hydrocarbons (PAH), methoxyphenols (MP), levoglucosan (LG), elemental carbon (EC) and organic carbon (OC) from wheat and Kentucky bluegrass (KBG) stubble burning were quantified in a US EPA test burn facility. The PAH and MP EFs for combined solid+gas phases are 17±8.2 mg kg⁻¹ and 79±36 mg kg⁻¹, respectively, for wheat and 21±15 mg kg⁻¹ and 35±24 mg kg⁻¹, respectively, for KBG. LG, particulate EC and artifact-corrected OC EFs are 150±130 mg kg⁻¹, 0.35±0.16 g kg⁻¹ and 1.9±1.1 g kg⁻¹, respectively, for wheat and 350±510 mg kg⁻¹, 0.63±0.056 g kg⁻¹ and 6.9±0.85 g kg⁻¹, respectively, for KBG. Positive artifacts associated with OC sampling were evaluated and remedied with a two-filter system. EC and OC accounted for almost two-thirds of PM_2.5 mass, while LG accounted for just under 3% of the PM_2.5 mass. Since EFs of these pollutants generally decreased with increasing combustion efficiency (CE), identifying and implementing methods of increasing the CEs of burns would help reduce their emissions from agricultural field burning. PAH, OC and EC EFs are comparable to other similar studies reported in literature. MP EFs appear dependent on the stubble type and are lower than the EFs for hard and softwoods reported in literature, possibly due to the lower lignin content in wheat and KBG.     

Characterization of PM2.5-bound polycyclic aromatic hydrocarbons in Atlanta

Twenty-four hour PM_2.5 samples from a rural site, an urban site, and a suburban site (next to a major highway) in the metropolitan Atlanta area in December 2003 and June 2004 were analyzed for 19 polycyclic aromatic hydrocarbons (PAH). Extraction of the air samples was conducted using an accelerated solvent extraction method followed by isotope dilution gas chromatography/mass spectrometry determination. Distinct seasonal variations were observed in total PAH concentration (i.e. significantly higher concentrations in December than in June). Mean concentrations for total particulate PAHs in December were 3.16, 4.13, and 3.40 ng m^?3 for the urban, suburban and rural sites, respectively, compared with 0.60, 0.74, and 0.24 ng m^?3 in June. Overall, the suburban site, which is impacted by a nearby major highway, had higher PAH concentration than did the urban site. Total PAH concentrations were found to be well correlated with PM_2.5, organic carbon (OC), and elemental carbon (EC) in both months (r² = 0.36–0.78, p < 0.05), although the slopes from the two months were different. PAHs represented on average 0.006% of total PM_2.5 mass and 0.017% of OC in June, compared with 0.033% of total PM_2.5 and 0.14% of OC in December. Total PAH concentrations were also correlated with potassium ion (r² = 0.39, p = 0.014) in December, but not in June, suggesting that in winter biomass burning can potentially be an important source for particulate PAH. Retene was found at a higher median air concentration at the rural site than at the urban and suburban sites—unlike the rest of the PAHs, which were found at lower levels at the rural site. Retene also had a larger seasonal difference and had the weakest correlation with the rest of the PAHs measured, suggesting that retene, in particular, might be associated with biomass burning.     

Global atmospheric emission inventory of polycyclic aromatic hydrocarbons (PAHs) for 2004

The global atmospheric emissions of the 16 polycyclic aromatic hydrocarbons (PAHs) listed as the US EPA priority pollutants were estimated using reported emission activity and emission factor data for the reference year 2004. A database for emission factors was compiled, and their geometric means and frequency distributions applied for emission calculation and uncertainty analysis, respectively. The results for 37 countries were compared with other PAH emission inventories. It was estimated that the total global atmospheric emission of these 16 PAHs in 2004 was 520 giga grams per year (Gg y^?1) with biofuel (56.7%), wildfire (17.0%) and consumer product usage (6.9%) as the major sources, and China (114 Gg y^?1), India (90 Gg y^?1) and United States (32 Gg y^?1) were the top three countries with the highest PAH emissions. The PAH sources in the individual countries varied remarkably. For example, biofuel burning was the dominant PAH source in India, wildfire emissions were the dominant PAH source in Brazil, while consumer products were the major PAH emission source in the United States. In China, in addition to biomass combustion, coke ovens were a significant source of PAHs. Globally, benzo(a)pyrene accounted for 0.05% to 2.08% of the total PAH emission, with developing countries accounting for the higher percentages. The PAH emission density varied dramatically from 0.0013 kg km^?2 y in the Falkland Islands to 360 kg km^?2 y in Singapore with a global mean value of 3.98 kg km^?2 y. The atmospheric emission of PAHs was positively correlated to the country's gross domestic product and negatively correlated with average income. Finally, a linear bivariate regression model was developed to explain the global PAH emission data.     

Dry deposition fluxes and deposition velocities of PAHs at an urban site in Turkey

Even though dry deposition and air–water exchange of semivolatile organic compounds (SOCs) are important for surfaces in and around the urban areas, there is still no generally accepted direct measurement technique for dry deposition. In this study, a modified water surface sampler (WSS) configuration, including a filter holder and an XAD-2 resin column, was employed to investigate the polycyclic aromatic hydrocarbon (PAH) dry deposition in an urban area. The measured total (particle+dissolved) PAH fluxes to the WSS averaged to be 34 960±16 540 ng m⁻² d⁻¹. Average particulate PAH flux, determined by analyzing the filter in the WSS, was about 8% of the total PAH flux. Temporal flux variations indicated that colder months (October–April) had the highest PAH fluxes. This increase could be attributed to the residential heating as well as meteorological effects including lower mixing height. A high volume air sampler was concurrently employed to collect ambient air concentrations. The average total (gas+particle) atmospheric PAH concentration (456±524 ng m⁻³) was within the range of previously measured values at different urban locations. PAH concentrations in urban areas are more than two orders of magnitude higher than those measured in pristine areas and this result may indicate that urban areas have major source sectors and greater deposition rates are expected near to these areas. The average contribution of particle phase was about 10% in total concentration. Simultaneous particulate phase dry deposition and ambient air samples were collected in this study. Then, particulate phase apparent dry deposition velocities were calculated using the fluxes and concentrations for each PAH compound and they ranged from 0.1 to 1.2 cm s⁻¹. These values are in good agreement with previously reported values.     

Air–water exchange fluxes of polycyclic aromatic hydrocarbons in the tropical coast,Taiwan

Air–water exchange fluxes of polycyclic aromatic hydrocarbons (PAHs) were simultaneously measured in air and water samples from two sites on the Kenting coast, located at the southern tip of Taiwan, from January to December 2010. There was no significant difference in the total PAH (t-PAH) concentrations in both gas and dissolved phases between these two sites due to the less local input which also coincided to the low levels of t-PAH concentration; the gas and dissolved phases averaged 1.29 ± 0.59 ng m^?3 and 2.17 ± 1.19 ng L^?1 respectively. The direction and magnitude of the daily flux of PAHs were significantly influenced by wind speed and dissolved PAH concentrations. Individual PAH flux ranged from 627 ng m^?2 d^?1 volatilization of phenanthrene during the rainy season with storm–water discharges raising dissolved phase concentration, to 67 ng m^?2 d^?1 absorption of fluoranthene during high wind speed periods. Due to PAH annual fluxes through air–water exchange, Kenting seawater is a source of low molecular weight PAHs and a reservoir of high molecular weight PAHs. Estimated annual volatilization fluxes ranged from 7.3 μg m^?2 yr^?1 for pyrene to 50 μg m^?2 yr^?1 for phenanthrene and the absorption fluxes ranged from ?2.6 μg m^?2 yr^?1 for chrysene to ?3.5 μg m^?2 yr^?1 for fluoranthene.     

Influence of temperature on PCDD/PCDF desorption from waste incineration flyash under nitrogen

A municipal solid waste incinerator flyash was heated to between 200 and 400 degrees C under nitrogen in a bench-scale, static bed reactor for 4 days soak time. The influence of temperature on the levels of PCDD and PCDF remaining in and desorbed from the ash were investigated using GC-MS/MS. PCDD and especially PCDF formation was seen on the flyash between 225 and 300 degrees C. Large increases in the I-TEQ of the treated ash relative to the increase in its overall PCDD/PCDF content indicated that the formation of 2378-substituted congeners was favoured over that of other substitution patterns. In the absence of a source of gaseous oxygen, formation was mainly attributed to de novo reactions involving solid phase oxygen. Dechlorination of the PCDD/PCDF in flyash became increasingly important above 275 degrees C. Maximum desorption was seen at 325 degrees C, with the equivalent of 35 wt% of the PCDD/F in the original flyash being recovered from the exhaust traps at this temperature. The desorbed species were mainly M(1)CDD/CDDF-T(3)CDD/CDDF resulting from dechlorination of higher chlorinated PCDD/PCDF, with consequently low I-TEQ values.     

Emission of polycyclic aromatic hydrocarbons from gasohol and ethanol vehicles

The exhaust emission of the polycyclic aromatic hydrocarbons (PAHs) considered toxic to human health were investigated on two spark ignition light duty vehicles, one being gasohol (Gasohol, in Brazil, is the generic denomination for mixtures of pure gasoline plus 20–25% of anhydrous ethyl alcohol fuel (AEAF).)-fuelled and the other a flexible-fuel vehicle fuelled with hydrated ethanol. The influence of fuel type and quality, aged lubricant oil type and use of fuel additives on the formation of these compounds was tested using standardized tests identical to US FTP-75 cycle. PAH sampling and chemical analysis followed the basic recommendations of method TO-13 (United States. Environmental Protection Agency, 1999. Compendium Method TO-13A – Determination of polycyclic Aromatic hydrocarbons (PAH) in Ambient Air Using Gas Chromatography/Mass Spectrometry (CG/MS). Center for environmental research information, Cincinnati, p. 78), with the necessary modification for this particular application.Results showed that the total PAH emission factor varied from 41.9 μg km^?1 to 612 μg km^?1 in the gasohol vehicle, and from 11.7 μg km^?1 to 27.4 μg km^?1 in the ethanol-fuelled vehicle, a significant difference in favor of the ethanol vehicle. Generally, emission of light molecular weight PAHs was predominant, while high molecular weights PAHs were not detected. In terms of benzo(a)pyrene toxicity equivalence, emission factors varied from 0.00984 μg TEQ km^?1 to 4.61 μg TEQ km^?1 for the gasohol vehicle and from 0.0117 μg TEQ km^?1 to 0.0218 μg TEQ km^?1 in the ethanol vehicle.For the gasohol vehicle, results showed that the use of fuel additive causes a significant increase in the emission of naphthalene and phenanthrene at a confidence level of 90% or higher; the use of rubber solvent on gasohol showed a reduction in the emission of naphthalene and phenanthrene at the same confidence level; the use of synthetic oil instead of mineral oil also contributed significantly to a decrease in the emission of naphthalene and fluorene. In relation to the ethanol vehicle, the same factors were tested and showed no statistically significant influence on PAH emission.     

Contribution of isoprene to formaldehyde and ozone formation based on its oxidation products measurement in Beijing,China

The atmospheric mixing ratios of methacrolein (MACR) and methyl vinyl ketone (MVK), the two specific products from isoprene oxidation in the atmosphere, were measured in Beijing from March to November, 2006. Distinct amounts of MACR and MVK were detected during vegetable growing seasons from April to October with ambient levels of 0.11–0.67 ppbv and 0.19–1.36 ppbv, respectively. The reacted isoprene and its ozone formation potentials (OFPs) in Beijing were evaluated in the range of 0.49–3.46 ppbv and 6.4–44.7 ppbv, respectively, from April to October. OFP of the reacted isoprene accounted for 10.6–23.6% of the total OFPs of VOCs (including carbonyls and isoprene) and 6.38–29.9% of the photo-chemically produced ozone. The maximum OFP of the original emitted isoprene prior to its photo-oxidation was calculated as 56.0 ppbv in August. The contribution from the reacted isoprene in Beijing to HCHO formation was also estimated to be in the range of 0.35–2.45 ppbv from April to October, which accounted for 4.6–11.5% of ambient HCHO.     

Concentrations of PCDD/PCDF in soil close to a secondary aluminum smelter

Polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDDs/Fs) were analyzed in samples of the emissions from a secondary aluminum smelter (ALS) and soil samples around the plant. The purpose was to estimate the impact of the emissions on the surrounding environment.PCDD/F soil concentrations were higher in the proximity of the plant, exceeding the limit adopted in Italy in soils for green areas and residential uses and the upper limit of several reference concentrations. The most contaminated sites were less than 500 m from the plant and the dioxin concentration with the distance from the ALS.Principal component analysis (PCA) showed that emissions from the ALS were the source of PCDD/F contamination in the soils closest to the plant. Multivariate data analyses such as PCA are therefore useful to identify sources of emission causing contamination.