Toxic emissions during co-combustion of biomass-waste wood-lignite blends in an industrial boiler

The objectives of this work were to study the PCDD/F emissions during the co-combustion of waste wood/coal co-combustion in an industrial boiler and to determine the relation of the toxic emissions to the fuel properties. Co-combustion experiments were performed in a 13.8 MWthermal industrial moving grate combustor. The fuels which were examined in this study included Greek lignite, natural uncontaminated wood, power poles and medium density fibers (MDFs) which were by-products of the plant production process. Fuel blends were prepared by mixing single components in various concentrations. PCDD/F emissions were collected during experimental runs and were analyzed according to standard methods. Low PCDD/F emissions were obtained during the co-combustion tests, lower than the limit value of 0.1 ng TEQ/Nm3. The lowest values were observed during the combustion of fuel blends containing MDF, possibly due to the inhibitory action of some of the N-containing MDF ingredients, such as urea. No direct correlation was found between the PCDD/F and the copper emissions, while examination of the PCDD/F homologue patterns revealed the predominance of the lower chlorinated isomers over the higher ones.     

Emissions of polychlorinated dibenzo-p-dioxins and dibenzofurans from stack gases of electric arc furnaces and secondary aluminum smelters

This study investigates the emissions of polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) from four electric arc furnaces (EAFs) and eight secondary aluminum smelters (secondary ALSs) in Taiwan. The mean PCDD/F International-Toxicity Equivalents (I-TEQ) concentrations in the stack gases of these EAFs and secondary ALSs are 0.28 ng I-TEQ/Nm3 (relative standard deviation [RSD]= 100%) and 3.3 ng I-TEQ/Nm3 (RSD = 260%), respectively. The high RSDs, especially for those obtained from secondary ALSs, could be caused by the intrinsic differences in their involved feeding materials, furnace operating conditions, and air pollution control devices. The mean I-TEQ emission factor of PCDD/Fs for EAFs (1.8 microg I-TEQ/tonne-feedstock) is lower than that for secondary ALSs (37 microg I-TEQ/tonne-feedstock). This result might be because the involved furnace temperatures for secondary ALSs (650-750 degrees C) are lower than those for EAFs (1600-1700 degrees C), resulting in the deterioration of the combustion condition, leading to the formation of PCDD/Fs during the industrial process. This study found that the total PCDD/F emissions from EAFs (20 g I-TEQ/yr) and secondary ALSs (18 g I-TEQ/yr) are approximately 27, 53, and approximately 24, 49 times higher than those from municipal solid waste incinerators (MSWIs; 0.74 g I-TEQ/yr) and medical waste incinerators (MWIs; 0.37 g I-TEQ/yr), respectively; while those are 44 and 40% of total PCDD/F emission from sinter plants (45 g I-TEQ/ yr), respectively. Considering a more stringent emission limit has been applied to waste incinerators (0.1 ng I-TEQ/Nm3) in Taiwan lately, the results suggest that the control of the emissions from metallurgical processes has become the most important issue for reducing the total PCDD/F emission from industrial sectors to the ambient environment.     

Urea as a PCDD/F inhibitor in municipal waste incineration

Emissions of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) from municipal waste incineration have been widely studied because of their extensive toxicity, and many efforts have been made to restrict their emissions. Although a number of chemical compounds have been shown in laboratory-scale tests to inhibit the formation of PCDD/Fs, few have been tested in pilot- or full-scale plants. This work evaluates the effect of urea as a PCDD/F inhibitor in a pilot-scale incinerator that uses refuse-derived fuel (RDF). The decomposition of urea under the test conditions was also studied using detailed kinetic modeling. An aqueous solution of urea was injected into the flue gas stream after the furnace at approximately 730 degrees C, with varied urea concentrations and flue gas residence times used between the furnace and the sampling point. The results demonstrate that urea can successfully inhibit PCDD/F formation in waste incineration if concentrations and injection points are properly adjusted. The kinetic model showed that urea can be rapidly decomposed under appropriate flue gas conditions, indicating that in addition to the urea molecule itself, decomposition products of urea can also be responsible for the reduction of PCDD/F production during incineration.     

Urea as a PCDD/F Inhibitor in Municipal Waste Incineration

ABSTRACT

Emissions of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) from municipal waste incineration have been widely studied because of their extensive toxicity, and many efforts have been made to restrict their emissions. Although a number of chemical compounds have been shown in laboratory-scale tests to inhibit the formation of PCDD/Fs, few have been tested in pilot- or full-scale plants. This work evaluates the effect of urea as a PCDD/F inhibitor in a pilot-scale incinerator that uses refuse-derived fuel (RDF). The decomposition of urea under the test conditions was also studied using detailed kinetic modeling. An aqueous solution of urea was injected into the flue gas stream after the furnace at ~730 °C, with varied urea concentrations and flue gas residence times used between the furnace and the sampling point. The results demonstrate that urea can successfully inhibit PCDD/F formation in waste incineration if concentrations and injection points are properly adjusted. The kinetic model showed that urea can be rapidly decomposed under appropriate flue gas conditions, indicating that in addition to the urea molecule itself, decomposition products of urea can also be responsible for the reduction of PCDD/F production during incineration.     

PCDD/PCDF emissions from small firing systems in households

This report presents results of emission measurements of polychlorinated dibenzo-p-dioxins (PCDD) and polychlorinated dibenzofurans (PCDF) in the flue gas of seven oil, nine gas, and two wood firing systems under laboratory conditions. The burn rate of the combustion was in the range of the rated useful heat output. Two additional test series varied the amount of combustion air and thus the heat output. The PCDD/PCDF emissions for oil- and gas-fired boilers are in the range of 0.0020-0.0142 ng I-TEQ/m3 (referring to 3% O2 in the dry flue gas). No correlation between the combustion technique and the PCDD/PCDF emissions could be established. In the tests with the wood-fired furnaces PCDD/PCDF concentrations in the flue gas ranging from 0.014 to 0.076 ng I-TEQ/m3 (referring to 13% O2 in the dry flue gas) were found. A significant correlation between the firing rate of the heating insert and the measured PCDD/PCDF concentrations was found. On examination of three typical 2,3,7,8-CDD/CDF congener profiles, a comparable pattern could be observed with natural gas and light fuel oil. The congener distribution for wood combustion is considerably different.     

Polychlorinated dibenzo-p-dioxin (PCDD) and dibenzofuran (PCDF) isomer patterns from municipal waste combustion: formation mechanism fingerprints

Polychlorinated dibenzo-p-dioxin (PCDD) and dibenzofuran (PCDF) byproducts can be formed in combustion systems by a variety of mechanisms. While total PCDD/F emissions and, to a lesser extent, homologue distributions from incinerators have been found to vary widely depending on combustion conditions, PCDD/F isomer distributions do not. Formation mechanisms can be grouped into two general categories: condensation of precursors, such as chlorinated phenols, and formation from particulate carbon, termed de novo synthesis. In addition to these mechanisms, chlorination and dechlorination reactions may affect isomer patterns. In this work, isomer patterns from field and laboratory municipal waste combustion samples are compared with computed thermodynamic distributions and those from the following experimental investigations: both gas-phase and metal-catalyzed condensation of chlorinated phenols, chlorination of dibenzo-p-dioxin and dibenzofuran, and dechlorination of octachlorodibenzo-p-dioxin and octachlorodibenzofuran. PCDD/F isomer patterns produced by different formation mechanisms in controlled experiments are distinct and robust, largely unaffected by combustion conditions. PCDD isomer patterns from municipal waste combustion are most similar to those produced by CuCl(2)-catalyzed phenol condensation from 10 chlorinated phenols. PCDF isomer patterns are most similar to those produced by chlorination and dechlorination.     

Investigations on the effect of chlorine in lubricating oil and the presence of a diesel oxidation catalyst on PCDD/F releases from an internal combustion engine

This paper reports on an intensive study into releases of polychlorinated dibenzo-p-dioxins (PCDD), polychlorinated furans (PCDF) and polychlorinated biphenyls (PCB) from a diesel engine and the analysis of PCDD/F and PCB in crankcase lubricating oil. Experimental conditions were set and carefully controlled in order to maximize the possible impact of, and our ability to measure the effect of, changes in the levels of chlorine in the lubricant. Emissions to air were measured using modified EPA methods following the principles of the European EN 1948 standards. A series of 40 experimental runs were completed using three reference lubricants formulated to have three levels of chlorine present as a residual component (at levels of 12, 131 and 259 mg kg(-1) or ppm). The engine was run with and without the diesel oxidation catalyst. All lubricants were realistic oils and the use of unrealistic additives or doping of components - particularly chlorine - in the fuel and lubricant was carefully avoided. Analysis of fuel and lubricant (before and after testing) samples required strenuous attention to achieve acceptable recoveries and showed non-detectable levels of PCB and PCDD/F at a detection limit of around 1.5 ng I-TEQ kg(-1) (ppt), indistinguishable from the laboratory blank. The testing demonstrated the need for extreme care to be taken in developing measurement methods that are sufficiently sensitive for measuring chlorine content of fluids and PCDD/F in oils, the latter being particularly challenging. Mean emissions of PCDD/F with the diesel oxidation catalyst in place were 23 pg I-TEQ l(-1) of fuel and with the diesel oxidation catalyst removed 97 pg I-TEQ l(-1) of fuel. The results of this testing showed that the emissions of PCDD/F were greatly reduced by the presence of a diesel oxidation catalyst in the exhaust, a finding that has not been explicitly tested in previous work. They also show that emissions from the engine were not controlled by the level of chlorine in the lubricant and that emissions did not change in response to a much greater step change in the total chlorine entering the combustion chamber due to a change in the level of chlorine in the fuel. Emissions when the engine was configured with a diesel oxidation catalyst showed a consistent pattern that appears to be unique in the experience of the authors.     

PCDD/F emissions from heavy duty vehicle diesel engines

The currently available information on PCDD/F emissions from diesel vehicles is briefly surveyed. Considerable uncertainty is identified concerning the emissions from heavy duty diesel trucks which have been measured only twice so far. These measurements led to emission factors differing by a factor of 200; similar discrepancy was also revealed by measurements of ambient air in traffic tunnels. New PCDD/F emission measurement results are presented which have been carried out at the exhaust systems of a stationary engine and of a modern heavy duty vehicle engine at transient operation conditions simulated on a test bench. PCDD/F concentrations in the exhaust gases were found to be in the range of control blank samples. Based on the highest concentration observed in the truck engine exhaust (9.7 pg I-TEQ/dry standard m3) a worst case estimate of the annual PCDD/F emission freight from diesel fuel combustion in the European countries of about 30 g I-TEQ/year is calculated. This emission appears to be irrelevant compared to the overall emission rate of more than 6,000 g I-TEQ/year being inventoried recently. Finally the possibilities to link congener/homologue profiles of diesel emission to profiles found in food or human samples are discussed.     

Environmental impact of a new hazardous waste incinerator in Catalonia,Spain: PCDD/PCDF levels in herbage samples

In April 1996 and 1998, the concentrations of polychlorinated dibenzo-p-dioxins (PCDD) and polychlorinated dibenzofurans (PCDF) were determined in 40 herbage samples collected in the neighborhood of a hazardous waste incinerator (HWI) under construction in Constanti (Catalonia, Spain). In April 2000, 20 months after the HWI began operating, herbage samples were again collected at the same sampling points in which samples had been taken in the previous surveys. PCDD/F concentrations ranged between 0.13 and 0.65 ng I-TEQ/kg (dry matter), with a median and mean values of 0.29 and 0.32 ng I-TEQ/kg (dry matter), respectively. The results were compared with those obtained in the 1996 (median, 0.53 ng I-TEQ/kg; mean, 0.61 ng I-TEQ/kg) and the 1998 (median, 0.23 ng I-TEQ/kg; mean, 0.31 ng I-TEQ/kg) surveys. While in the period 1996-1998 a significant decrease (49%, P < 0.001) in the mean PCDD/F levels was noted, in the period 1998-2000 an increase of 3% (P > 0.05) was found in the concentrations of PCDD/Fs. The analysis of the results suggests two potential hypotheses: either the emissions of PCDD/Fs from the HWI are not negligible, or the current PCDD/F emissions from other sources near the HWI remained at similar levels to those reached in 1998. Anyhow, an exhaustive evaluation of the present data shows an absence of notable PCDD/F contamination by the HWI in the area under its direct influence. It seems also probable that the decline in the atmospheric levels of PCDD/Fs due other emission sources of PCDD/Fs in this area is currently stopped.     

Cleaner co-combustion of lignite-biomass-waste blends by utilising inhibiting compounds of toxic emissions

In this paper, the co-combustion behaviour of coal with wastes and biomass and the related toxic gaseous emissions were investigated. The objective of this work is to add on towards a cleaner co-combustion of lignite-waste-biomass blends by utilizing compounds that could inhibit the formation of toxic pollutants. A series of co-combustion tests was performed in a pilot scale incinerator, and the emissions of polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs) were measured. The co-combustion behaviour of lignite with olive kernels, MDF and sawdust was studied and the ability of additives such as urea, almond shells and municipal sewage sludge to reduce the PCDD/F emissions was examined. All blends were proven good fuels and reproducible combustion conditions were achieved. The addition of inhibitors prior to combustion showed in some cases, relatively high PCDD/F emissions reduction. Among the inhibitors tested, urea seems to achieve a reduction of PCDD/F emissions for all fuel blends, while an unstable behaviour was observed for the others.     

Evaluation of the emission characteristics of PCDD/Fs from electric arc furnaces

Distribution of PCDD/F (polychlorinated dibenzo-p-dioxin and polychlorinated dibenzofuran) congeners at two electric arc furnaces (EAFs) in Taiwan is evaluated via intensive stack sampling and analysis. Two kinds of exhaust system in EAFs including stack system and shutter system are selected for measuring dioxin emissions. In addition, dioxin emissions during oxidation and reduction stages at EAF-A were characterized. Results indicate that the PCDD/F concentration of stack gas in EAF-A was 4.39 ng/N m³ while total Toxic Equivalent Quantity (TEQ) concentration was 0.35 ng I-TEQ/N m³. The PCDD/F concentration of stack gas in EAF-B was 2.20 ng/N m³ and the TEQ concentration was 0.14 ng I-TEQ/N m³. 1,2,3,4,6,7,8-H_pCDF, OCDD and OCDF are the major contributors of the dioxin concentrations for two EAFs investigated and the percentage of PCDD/F in particulate phase increases as the chlorination level of the PCDD/F congener increases. The results obtained on gas/particulate partitioning of PCDD/Fs in flue gases prior to the APCD in EAFs indicate that more than 90% exists in particulate phase. In EAF-A, the PCDD/F concentration during oxidation stage is slightly higher than that measured during reduction stage, including the sampling points of CO converter outlet, prior to bag filter and stack. Majority of PCDD/Fs emitted from steel-making processes exists in particulate-phase (about 60–70%) at both EAFs investigated.     

Emissions behavior and distribution of polychlorinated dibenzo-p-dioxins and furans (PCDD/Fs) from cement kilns in China

The production of cement in China is accompanied by various emissions, such as fine particulate matter, heavy metals, nitrogen oxides, sulfur oxides, carbon dioxide…. Moreover, cement kiln presents a potential health risk to its surroundings, linking to emissions of persistent organic pollutants (POPs), such as polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), in brief dioxins. Flue gas samples were collected from five typical cement kilns during twelve runs and were used to evaluate the levels and distribution of PCDD/Fs in the emissions from cement kilns. The PCDD/Fs concentrations (136 congeners) and I-TEQ values ranged from 2.3 to >40 ng/m³ and 9.3?～?90.8?×?10^?3 ng I-TEQ/m³, respectively, which were lower than the emission standard in China (0.1 ng I-TEQ/m³). In weight units, the dominant congeners were OCDD, 1,2,3,4,6,7,8-HpCDF, and OCDF; 2,3,4,7,8-PeCDF is the largest contributor (36–66 %) to the total I-TEQ value of twelve runs. HxCDF and TCDF were the first two most abundant homologue groups (12–85 and 4–52 %), and the homologue concentration decreased with rising chlorine number for PCDDs. In addition, there was no marked difference in homologue profiles when solid wastes (refuse-derived fuel and municipal solid waste) and hazardous wastes (DDT and POPs) were combusted as supplemental fuels. The use of various supplemental fuels had no obvious effect on the fingerprint of PCDD/F homologues. Moreover, there was no significant difference in levels of PCDD/Fs emission due to the diversity of production capacity, which were consistent with reported previously. Air pollution control device had effect on the homologue profiles, and cement system with electrostatic precipitators (ESP) had more fractions of octachloro congeners to the total.     

Sources of dioxins in the United Kingdom: the steel industry and other sources

Several countries have compiled national inventories of dioxin (polychlorinated dibenzo-p-dioxin [PCDD] and polychlorinated dibenzofuran [PCDF]) releases that detail annual mass emission estimates for regulated sources. High temperature processes, such as commercial waste incineration and iron ore sintering used in the production of iron and steel, have been identified as point sources of dioxins. Other important releases of dioxins are from various diffuse sources such as bonfire burning and domestic heating. The PCDD/F inventory for emissions to air in the UK has decreased significantly from 1995 to 1998 because of reduced emissions from waste incinerators which now generally operate at waste gas stack emissions of 1 ng I-TEQ/Nm3 or below. The iron ore sintering process is the only noteworthy source of PCDD/Fs at integrated iron and steelworks operated by Corus (formerly British Steel plc) in the UK. The mean waste gas stack PCDD/F concentration for this process is 1,2 ng I-TEQ/Nm3 based on 94 measurements and it has been estimated that this results in an annual mass release of approximately 38 g I-TEQ per annum. Diffuse sources now form a major contribution to the UK inventory as PCDD/Fs from regulated sources have decreased, for example, the annual celebration of Bonfire Night on 5th November in the UK causes an estimated release of 30 g I-TEQ, similar to that emitted by five sinter plants in the UK.     

Effects of burnings of wax apple stubble and rice straw on polychlorinated dibenzo-p-dioxin and dibenzofuran concentrations in air and soil

Measurements of the concentrations of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) were made in ambient air, ash, and soil impacted by the open burning of wax apple and rice straw residues. Measurements showed that the mean PCDD/F concentration (0.458 pg I-TEQ/Nm3; international toxicity equivalence) in air at two wax apple orchards during open burning increased markedly, -8.1 times higher than that (0.057 pg I-TEQ/Nm3); before open burning. In addition, the mean PCDD/F concentration (0.409 pg I-TEQ/Nm3) in ambient air at a rice straw field was 4.6 times higher than that (0.089 pg I-TEQ/Nm3) before open burning. After burning the residues of wax apple stubble and rice straw, the contents of PCDD/F in ashes were 1.393 and 1.568 ng I-TEQ/kg-ash, respectively, and the contents of PCDD/F in soil were 2.258 and 2.890 ng I-TEQ/kg-soil, respectively. Therefore, the turnover of soil with the ash after open burning over years will result in the accumulation of PCDD/Fs in farm soils.     

Post-combustion syntheses of PCDD/F and PBDD/F from halogen-rich fuel is suppressed by a pebble heater technology

GOAL, SCOPE AND BACKGROUND: Changes in German and European legislation shifted processing of polymer-rich shredding residues (SR) from landfill to thermal treatment. However, when waste of electric and electronic equipment (WEEE) is the source of SR, thermal treatment is complicated by halogens as well as the presence of polybrominated dioxins and furans (PBDD/F) and brominated flame retardants (BFR). Hence, WEEE requires high temperature incineration with sufficient residence times. Post-combustion synthesis of polyhalogenated dioxins and furans (PXDD/F) is dominant in the temperature range between 250-450 degrees C. Thus, a very rapid gas cooling from 450 degrees to 250 degrees C is important for proper raw gas treatment. The pebble heater technology developed by ATZ Entwicklungszentrum (Sulzbach-Rosenberg, Germany) might serve as an alternative to the state-of-the-art quench cooling. It is based on the application of a pebble bed of natural bulk material, which the exhaust gases flows through radially. It provides an excellent heat transfer and a temperature gradient in the range of 1,500-2,000 K/m. The paper presents data of a pilot application of the pebble heater technology for the treatment of raw gas derived from the incineration of polymeric materials from WEEE. METHODS: A liquid fuel was chosen in order to minimise technical modifications of the plant. It was analysed for halogens by x-ray fluorescence, for brominated flame retardants by HPLC-UV/MS and for PXDD/F by GC-HRMS. Combustion gases were rapidly cooled down to temperatures below 200 degrees C and emissions of PBDD/F and PCDD/ F were estimated without further off-gas treatment. PBDD/F emissions were computed as PCDD/F toxicity equivalents applying two different calculation approaches. RESULTS AND DISCUSSION: PCDD/F emissions accounted for 0.04 ng I-TEQ/Nm3 and are in compliance with European emission limits. Calculated PBDD/F toxicity equivalents exceeded the emission limit of 0.1 ng I-TEQ/Nm3 by factors of 75 and 208 depending on the calculation approach. A mass balance of PBDD/F and PCDD/F congeners revealed an efficient elimination of more than 95% in most cases. Lower reduction rates (76% for 2,3,7,8-TeBDF and 82% for 1,2,3,7,8-PeBDF) were attributed to incomplete combustion. An intended recovery of halogens by one-stage scrubbing downstream of the pebble heater was ineffective, recovering 28% of the applied chlorine and 9% of the bromine, only. CONCLUSIONS: Our pilot incineration test indicates that the pebble heater technology can effectively suppress a post-combustion synthesis of PCDD/F and PBDD/F, resulting in low PCDD/F emission levels without further off-gas treatment. The presented data state that WEEE is sensible to incomplete combustion, which will lead to increased PBDD/F emissions without increasing PCDD/F emission limits. This finding is especially relevant for small and low-technical incineration appliances, which have been reported to treat WEEE in developing countries and are considered to serve as a significant source of PXDD/F these days. RECOMMENDATIONS AND PERSPECTIVES: Monitoring of PCDD/F emissions only might considerably underestimate the total emission of dioxins and dioxin-like compounds. It is therefore an ineffective means for assessing resulting health risks, at least for those waste treatment plants which are considered to handle the increasing amounts of PBDD/ F-containing polymers from WEEE in future. Consequently, it is recommended to initiate a screening programme for PXDD/F emissions in large scale incineration facilities which are capable of treating WEEE shredder residues.     

Formation of PCDD/PCDF

One option of recycling used contaminated packaging is to recover its high energy content. This can be performed in a normal multi-fuel power plant by co-combustion of packaging-derived fuel (PDF) or refuse-derived fuel (RDF) with fossil fuels, such as coal or peat. This work includes the results of 17 co-combustion tests and an evaluation of the results by the Principal Component Analysis (PCA) and the Partial Least Squares Projections to Latent Structures (PLS). PCA and PLS calculations showed that especially Pb, but also Cr, and Cu correlated with lower chlorinated furans (PCDFs) in the fly ash. Correlation between Sn and lower chlorinated dioxins (PCDDs) in the fly ash was also noticed. CO and PAH emission in the flue gas correlated with total PCDD/Fs in the flue gas. In a real full-scale combustion process, a single parameter in fuel, flue gas or a combustion parameter did not provide a guide to PCDD/F formation or to a level of the total PCDD/F emission, but correlations between different parameters and PCDD/Fs could be found. Although PDFs and RDF had catalytic heavy metals and chlorine, the co-combustion results showed that they can be co-combusted with peat and coal in a fluidized-bed boiler at least up to 26 % with very low total PCDD and PCDF emissions.     

PCDD/F reduction in incinerator flue gas by adding urea to RDF feedstock

The effect of urea on PCDD/F formation in a pilot incinerator was studied by incinerating urea with refuse-derived fuel (RDF) at three concentrations (0.1%, 0.5% and 1.0%, of the fuel feed). A distinct reduction in both PCDD/F and chlorophenol concentrations could be noticed when urea was introduced into the system. Partial-least-square (PLS) analysis of the data showed the importance of certain chlorophenol isomers as PCDD/F precursors, pointing to the possibility that the impact point of the urea inhibitor could be before the precursor molecules, i.e. chlorophenols, have been formed.     

Influence of start-up on PCDD/F emission of incinerators

This study aims to evaluate the influence of start-up on polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) concentration in the stack flue gas of incinerators and its contributing PCDD/F emission. The PCDD/F emission of the first sample among three consecutive stack flue gas samples of five intermittent incinerators, which sampled at a stable combustion condition after start-up, is 2-3 times higher than the mean of the others. For verifying the PCDD/F characteristics of incinerators during start-up, one continuous MSWI was investigated for two years. The elevated PCDD/F emissions of the MSWI during start-up could reach 96.9 ng I-TEQN m(-3) and still maintained a high PCDD/F emission (40 times higher than the Taiwan emission limit) even 18 h after the injection of activated carbon, indicating the memory effect. Taking the MSWI for example, which consists of four incinerators, the estimated annual PCDD/F emission from normal operational conditions was 0.112 g I-TEQ. However, one start-up procedure can generate approximately 60% of the PCDD/F emissions for one whole year of normal operations. And the PCDD/F emission, which is the result of the start-ups of four incinerators, was at least two times larger than that of a whole year's normal operations, without consideration for the PCDD/F emission contributed by the long lasting memory effect.     

Correlation of PCDD/F and PCB concentrations in soil samples from the Swiss soil monitoring network (NABO) to specific parameters of the observation sites

Concentrations of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/F) and polychlorinated biphenyls (PCB) were determined in 23 soil samples collected at reference sites of the Swiss national soil monitoring network (NABO). Total PCDD/F and PCB concentrations are well correlated and proportional (R2=0.720). The total PCDD/F levels were between 72 and 703 ng/kg corresponding to 1.1-11 ng I-TEQ/kg, total PCB concentrations (sum of seven congeners IUPAC no. 28, 52, 101, 118, 138, 153, and 180) were from 1.1 to 12 microg/kg. In all samples, the PCDD/F and PCB concentrations were in the range of background levels for these contaminants in Central Europe. Ninteen samples revealed PCDD/F levels below the guide value of 5 ng I-TEQ/kg set by the Swiss ordinance relating to impacts on the soil (OIS); concentrations for the remaining four samples were below the trigger value (20 ng I-TEQ/kg). All PCB concentrations were below the guide value of 100 microg/kg. The elevated PCDD/F and PCB levels in some of the samples originating from forested sites could be attributed to the scavenging effect of forest canopies for semivolatile organic compounds. This interpretation could be substantiated by the observed distortion of the congener and homolog patterns of PCDD/F and PCB which is characteristic for forested sites.     

Levels and characteristic homologue patterns of polychlorinated dibenzo-p-dioxins and dibenzofurans in various incinerator emissions and in air collected near an incinerator

Polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) were monitored in stack gas and fly ash of various Korean incinerators and in air samples collected near the facilities. Concentrations of PCDD/Fs in emissions were investigated, and characteristic PCDD/F homologue patterns were classified using statistical analyses. The PCDD/F emission levels in stack gas and fly ash samples from small incinerators (SIs) were higher than those from municipal solid waste incinerators (MSWIs). The PCDD/F concentrations ranged between 0.38 and 1.16 pg I-TEQ/m3 (21.2-75.2 pg/m3) in ambient air samples. The lower-chlorinated furans were the dominant components in most of the stack gas and fly ash samples from SIs, although this was not the case for fly ash from MSWIs. This homologue pattern is consistent with other studies reporting a high fraction of lower-chlorinated furans in most environmental samples affected by incinerator emissions, and it can be used as an indicator to assess the impact of such facilities on the surrounding environment.