Development of a PM2 5 Emissions Inventory for the South Coast Air Basin

ABSTRACT

With the promulgation of a national PM_2.5 ambient air quality standard, it is important that PM_2.5 emissions inventories be developed as a tool for understanding the magnitude of potential PM2.5 violations. Current PM₁₀ inventories include only emissions of primary particulate matter (1 ^ï PM), whereas, based on ambient measurements, both PM₁₀ and PM2.5 emissions inventories will need to include sources of both 1^ï PM and secondary particulate matter (2^ï PM). Furthermore, the U. S. Environmental Protection Agency’s (EPA) current edition of AP-42 includes size distribution data for 1o PM that overestimate the PM_2.5 fraction of fugitive dust sources by at least a factor of 2 based on recent studies.

This paper presents a PM_2.5 emissions inventory developed for the South Coast Air Basin (SCAB) that for the first time includes both 1^ï PM and 2^ï PM. The former is calculated by multiplying PM₁₀ emissions estimates by the PM_2.5/PM₁₀ ratios for different sources. The latter is calculated from estimated emission rates of gas-phase aerosol precursor and gas to aerosol conversion rates consistent with the measured chemical composition of ambient PM_2.5 concentrations observed in the SCAB. The major finding of this PM_2.5 emissions inventory is that the ^2ï aerosol component is more than twice the ^1ï aerosol component, which may result in widely different control strategies being required for fine PM and coarse PM.     

Particulate Matter in California: Part 1—Intercomparison of Several PM2.5, PM10–2.5, and PM10 Monitoring Networks

Abstract

It will be many years before the recently deployed network of fine particulate matter with an aerodynamic diameter less than 2.5 [H9262]m (PM_2.5) Federal Reference Method (FRM) samplers produces information on nonattainment areas, trends, and source impacts. However, data on PM_2.5 and its major constituents have been routinely collected in California for the past 20 years. The California Air Resources Board operated as many as 20 dichotomous (dichot) samplers for PM_2.5 and coarse PM (PM_10–2.5). The California Acid Deposition Monitoring Program (CADMP) collected 12-h-average PM_2.5 and PM₁₀ from 1988 to 1995 at ten urban and rural sites and 24-h-average PM_2.5 at five urban sites since 1995. Beginning in 1994, the Children’s Health Study collected 2-week averages of PM_2.5 in 12 communities in southern California using the Two-Week Sampler (TWS). Comparisons of collocated samples establish relationships between the dichot, CADMP, and TWS samplers and the 82-site network of PM_2.5 FRM samplers deployed since 1999 in California. PM mass data from the different monitoring programs have modest to high correlation to FRM mass data, fairly small systematic biases and negative proportional biases ranging from 7 to 22%. If the biases are taken into account, all of the programs should be considered comparable with the FRM program. Thus, historical data can be used to develop long-term PM trends in California.     

Source Apportionment of PM10 and PM25 in Five Chilean Cities Using Factor Analysis

ABSTRACT

Chile is a fast-growing country with important industrial activities near urban areas. In this study, the mass and elemental concentrations of PM₁₀ and PM_2.5 were measured in five major Chilean urban areas. Samples of particles with diameter less than 10 um (PM₁₀) and 2.5 um (PM_2.5) were collected in 1998 in Iquique (northern Chile), Valparaiso, Vina del Mar, Rancagua (central Chile), and Temuco (southern Chile). Both PM₁₀ and PM₂₅ annual mean concentrations (PM₁₀: 56.9-77.6 u,g/m³; PM₂₅: 22.4-42.6 u.g/m³) were significantly higher than the corresponding European Union (EU) and U.S. Environmental Protection Agency (EPA) air quality standards. Moreover, the 24-hr PM₁₀ and PM₂₅ U.S. standards were exceeded infrequently for some of the cities (Rancagua and Valparaiso).     

Understanding particulate matter formation in the California San Joaquin Valley: conceptual model and data needs

Quantitative information from the 1995 Integrated Monitoring Study (IMS95) is used to develop a conceptual model, which describes the chemical characteristics and the physical processes responsible for the accumulation of PM in the San Joaquin Valley of California. One significant finding of the conceptual model is the sensitivity of ammonium nitrate (46% of winter PM_2.5) and nitric acid to oxidants, which may be VOC-sensitive rather than NO_x-sensitive. Key gaps in current knowledge are identified using the conceptual model, e.g., the relative sensitivity of winter oxidants to VOC and NO_x, mechanistic details of secondary organic aerosol formation, mechanisms of dispersion under calm conditions, and the importance of dry deposition. Some recommendations are also provided for the formulation of air quality models suitable to address the accumulation of PM in the San Joaquin Valley.     

Characterization of Particulate Matter in California

ABSTRACT

The size, composition, and concentration of particulate matter (PM) vary with location and time. Several monitoring/sampling programs are operated in California to characterize PM less than 2.5 and 10 µm in aerodynamic diameter (PM_2.5 and PM₁₀). This paper presents a broad summary of the spatial and temporal variations observed in ambient PM_2.5 and PM₁₀ concentrations in California. Many areas that have high PM₁₀ concentrations also have relatively high PM_2.5 concentrations, and data indicate that a significant portion of the PM₁₀ air quality problem is caused by PM_2.5. To develop effective plans for attaining the ambient PM standards, improved understanding of these unique problems is needed. Since 1989, pollution control efforts—whether specifically targeted for particulate matter or indirectly via controls on gaseous emissions—have caused annual average PM_2.5 and PM₁₀ concentrations to decline at most sites in California.     

An integrated approach to identify the origin of PM10 exceedances

Purpose

This study was aimed to the development of an integrated approach for the characterization of particulate matter (PM) pollution events in the South of Italy.

Methods

PM₁₀ and PM_2.5 daily samples were collected from June to November 2008 at an urban background site located in Bari (Puglia Region, South of Italy). Meteorological data, particle size distributions and atmospheric dispersion conditions were also monitored in order to provide information concerning the different features of PM sources.

Results

The collected data allowed suggesting four indicators to characterize different PM₁₀ exceedances. PM_2.5/PM₁₀ ratio, natural radioactivity, aerosol maps and back-trajectory analysis and particle distributions were considered in order to evaluate the contribution of local anthropogenic sources and to determine the different origins of intrusive air mass coming from long-range transport, such as African dust outbreaks and aerosol particles from Central and Eastern Europe. The obtained results were confirmed by applying principal component analysis to the number particle concentration dataset and by the chemical characterization of the samples (PM₁₀ and PM_2.5).

Conclusions

The integrated approach for PM study suggested in this paper can be useful to support the air quality managers for the development of cost-effective control strategies and the application of more suitable risk management approaches.     

Estimation of Ambient PM2.5 Concentrations in Maryland and Verification by Measured Values

Abstract

In 1997, Maryland had no available ambient Federal Reference Method data on particulate matter less than 2.5 μm in aerodynamic diameter (PM_2.5), but did have annual ambient data for PM smaller than 10 μm (PM₁₀) at 24 sites. The PM₁₀ data were analyzed in conjunction with local annual and seasonal zip-code-level emission inventories and with speciated PM_2.5 data from four nearby monitors in the IMPROVE network (located in the national parks, wildlife refuges, and wilderness areas) in an effort to estimate annual average and seasonal high PM_2.5 concentrations at the 24 PM₁₀ monitor sites operating from 1992 to 1996. All seasonal high concentrations were estimated to be below the 24-hr PM_2.5 National Ambient Air Quality Standards (NAAQS) at the sites operating in Maryland between 1992 and 1996. The estimates also indicated that 12 monitor sites might exceed the 3-year annual average PM_2.5 NAAQS of 15 ug/m³, but Maryland’s air quality shows signs that it has been improving since 1992. The estimates also were compared with actual measurements after the PM_2.5 monitor network was installed. The estimates were adequate for describing the chemical composition of the PM_2.5, forecasting compliance status with the 24-hr and annual standards, and determining the spatial variations in PM_2.5 across central Maryland.     

An enhanced PM2.5 air quality forecast model based on nonlinear regression and back-trajectory concentrations

An enhanced PM_2.5 air quality forecast model based on nonlinear regression (NLR) and back-trajectory concentrations has been developed for use in the Louisville, Kentucky metropolitan area. The PM_2.5 air quality forecast model is designed for use in the warm season, from May through September, when PM_2.5 air quality is more likely to be critical for human health. The enhanced PM_2.5 model consists of a basic NLR model, developed for use with an automated air quality forecast system, and an additional parameter based on upwind PM_2.5 concentration, called PM24. The PM24 parameter is designed to be determined manually, by synthesizing backward air trajectory and regional air quality information to compute 24-h back-trajectory concentrations. The PM24 parameter may be used by air quality forecasters to adjust the forecast provided by the automated forecast system. In this study of the 2007 and 2008 forecast seasons, the enhanced model performed well using forecasted meteorological data and PM24 as input. The enhanced PM_2.5 model was compared with three alternative models, including the basic NLR model, the basic NLR model with a persistence parameter added, and the NLR model with persistence and PM24. The two models that included PM24 were of comparable accuracy. The two models incorporating back-trajectory concentrations had lower mean absolute errors and higher rates of detecting unhealthy PM2.5 concentrations compared to the other models.     

Fine Particle (PM25) Measurement Methodology,Quality Assurance Procedures,and Pilot Results of the EXPOLIS Study

ABSTRACT

EXPOLIS is a European multicenter (Athens, Basel, Grenoble, Helsinki, Milan, and Prague) air pollution exposure study. It is the first international, population-based, large-scale study, where personal exposures to PM_{2 5} aerosol particles (together with volatile organic compounds and carbon monoxide) are being monitored. EXPOLIS is performed in six different centers across Europe, the sampled aerosol concentrations vary greatly, and the mi-croenvironmental samples are not collected with the same equipment as the personal samples. Therefore careful equipment selection, methods development and testing, and thorough quality assurance and quality control (QA & QC) procedures are essential for producing reliable and comparable PM_2.5 data. This paper introduces the equipment, the laboratory test results, the pilot results, the standard operating procedures, and the QA & QC procedures of EXPOLIS. Test results show good comparability and repeatability between personal and microenvironmen-tal monitors for PM2.5 at different concentration levels measured across Europe in EXPOLIS centers.     

Wintertime PM2.5 and PM10 Source Apportionment at Sacramento,California

ABSTRACT

The chemical mass balance (CMB) model was applied to winter (November through January) 1991–1996 PM2.5 and PM10 data from the Sacramento 13th and T Streets site in order to identify the contributions from major source categories to peak 24-hr ambient PM_2.5 and PM₁₀ levels. The average monthly PM₁₀ monitoring data for the nine-year period in Sacramento County indicate that elevated concentrations are typical in the winter months. Concentrations on days of highest PM₁₀ are dominated by the PM2.5 fraction. One factor contributing to increased PM_2.5 concentrations in the winter is meteorology (cool temperatures, low wind speeds, low inversion layers, and more humid conditions) that favors the formation of secondary nitrate and sulfate aerosols. Residential wood burning also elevates fine particulate concentrations in the Sacramento area.

The results of the CMB analysis highlight three key points. First, the source apportionment results indicate that primary motor vehicle exhaust and wood smoke are significant sources of both PM_2.5 and PM₁₀ in winter. Second, nitrates, secondarily formed as a result of motor-vehicle and other sources of nitrogen oxide (NO_x), are another principal cause of the high PM_2.5 and PM₁₀ levels during the winter months. Third, fugitive dust, whether it is resuspended soil and dust or agricultural tillage, is not the major contributor to peak winter PM_2.5 and PM10 levels in the Sacramento area.     

Low emission zones reduce PM10 mass concentrations and diesel soot in German cities

In many European cities mass concentrations of PM₁₀ (particles less than 10 μm in size) are still exceeding air quality standards as set by the European Commission in 1999. As a consequence, many cities introduced low emission zones (LEZs) to improve air quality and to meet the limit values. In Germany currently 48 LEZs are in operation. By means of dispersion modeling, PM₁₀ concentrations were estimated to decrease up to 10%. Analysis of PM₁₀ levels conducted for Cologne, Berlin, and Munich some time after the LEZs were introduced showed reduction of PM₁₀ mass concentration in the estimated range. The PM₁₀ particle fraction is, however, composed of particles with varying toxicity, of which diesel soot is highly health relevant. An evaluation of air quality data conducted in Berlin showed that in 2010 traffic-related soot concentrations measured along major roads decreased by 52% compared to 2007. Diesel particle emissions in Berlin were reduced in 2012 by 63% compared to a business-as-usual scenario (reference year 2007). A strong reduction of the traffic-related particle fraction of PM_2.5 was also reported for Munich. Therefore, it is likely that the effects of LEZs are considerably more significant to human health than was anticipated when only considering the reduction of PM₁₀ mass concentrations.

Implications: The implementation of low emission zones in German cities might result in a reduction of PM₁₀ levels concentrations by up to 10%. However, it is difficult to show a reduction of PM₁₀ annual averages in this order of magnitude as meteorology has a large impact on the year-to-year variation of PM mass concentrations. Monitoring of other PM metrics such as black smoke (BS) or elemental carbon (EC) might be a better strategy for evaluating LEZs effects. The benefit of low emission zones on human health is far greater than is presently visible from routine measurements of PM₁₀.     

Windblown Dust Contributes to High PM25 Concentrations

ABSTRACT

The revised National Ambient Air Quality Standards for PM include fine particulate standards based upon mass measurements of PM₂₅. It is possible in arid and semi-arid regions to observe significant coarse mode intrusion in the PM_2.5 measurement. In this work, continuous PM₁₀, PM_2.5, and PM_1.0 were measured during several windblown dust events in Spokane, WA. PM_{2 5} constituted ~30% of the PM₁₀ during the dust event days, compared with ~48% on the non-dusty days preceding the dust events. Both PM₁₀ and PM_2.5 were enhanced during the dust events. However, PM_1.0 was not enhanced during dust storms that originated within the state of Washington. During a dust storm that originated in Asia and impacted Spokane, PM_1.0 was also enhanced, although the Asian dust reached Washington during a period of stagnation and poor dispersion, so that local sources were also contributing to high particulate levels. The “intermodal” region of PM, defined as particles ranging in aerodynamic size from 1.0 to 2.5 um, was found to represent a significant fraction of PM₂₅ (~51%) during windblown dust events, compared with 28% during the non-dusty days before the dust events.     

Application of positive matrix factorization in characterization of PM(10) and PM(2.5) emission sources at urban roadside

The 24-h average coarse (PM₁₀) and fine (PM_2.5) fraction of airborne particulate matter (PM) samples were collected for winter, summer and monsoon seasons during November 2008-April 2009 at an busy roadside in Chennai city, India. Results showed that the 24-h average ambient PM₁₀ and PM_2.5 concentrations were significantly higher in winter and monsoon seasons than in summer season. The 24-h average PM₁₀ concentration of weekdays was significantly higher (12-30%) than weekends of winter and monsoon seasons. On weekends, the PM_2.5 concentration was found to slightly higher (4-15%) in monsoon and summer seasons. The chemical composition of PM₁₀ and PM_2.5 masses showed a high concentration in winter followed by monsoon and summer seasons.The U.S.EPA-PMF (positive matrix factorization) version 3 was applied to identify the source contribution of ambient PM₁₀ and PM_2.5 concentrations at the study area. Results indicated that marine aerosol (40.4% in PM₁₀ and 21.5% in PM_2.5) and secondary PM (22.9% in PM₁₀ and 42.1% in PM_2.5) were found to be the major source contributors at the study site followed by the motor vehicles (16% in PM₁₀ and 6% in PM_2.5), biomass burning (0.7% in PM₁₀ and 14% in PM_2.5), tire and brake wear (4.1% in PM₁₀ and 5.4% in PM_2.5), soil (3.4% in PM₁₀ and 4.3% in PM_2.5) and other sources (12.7% in PM₁₀ and 6.8% in PM_2.5).     

Air quality at Santiago,Chile: a box modeling approach II. PM2.5, coarse and PM10 particulate matter fractions

Ambient monitored data at Santiago, Chile, are analyzed using box models with the goal of assessing contributions of different economic activities to air pollution levels. The box modeling approach was applied to PM₁₀, PM_2.5 and coarse (PM₁₀–PM_2.5) particulate matter (PM) fractions; the period analyzed is 1989–1999. A linear model for each PM fraction was obtained, having as independent variables CO and SO₂ concentrations, plus a term proportional to (wind speed)⁻¹ that lumps together non-combustion emissions and secondary generation terms; wet scavenging is included as another independent variable. Model identification results show good agreement for the different parameters across monitoring stations. The washout ratios and scavenging coefficients agree with data published in the literature, being higher for the coarse PM fraction. The CO and SO₂ coefficients fitted for 1989–1995 agree with a priori estimates for the same period. Background estimates for the PM fractions are in agreement with measurement campaigns in upwind sites. Results show that transportation sources have become the dominant contributors to ambient PM levels, while stationary sources have decreased their contributions in the last years. The relative importance of mobile sources to PM_2.5 ambient concentrations has doubled in the last 10 years, whereas stationary sources have reduced their relative contributions to half the value in the early 1990s. Model estimates of regional background of PM_2.5 and PM₁₀ have decreased 50% and 22% in the last decade, respectively; coarse background has shown no significant change. The final conclusion is that there is room and need for a more intensive emission reduction strategy for Santiago, focusing on mobile sources. The approach pursued in this work is feasible for cities or regions where comprehensive, transport and chemistry models are not available yet, but estimates of air quality contributions are needed for policy purposes. The methodology requires data on ambient air quality measurements and surface meteorology.     

Modeling air quality during the California Regional PM10/PM2.5 Air Quality Study (CPRAQS) using the UCD/CIT source-oriented air quality model – Part III. Regional source apportionment of secondary and total airborne particulate matter

A comprehensive air quality modeling project was carried out to simulate regional source contributions to secondary and total (=primary + secondary) airborne particle concentrations in California's Central Valley. A three-week stagnation episode lasting from December 15, 2000 to January 7, 2001, was chosen for study using the air quality and meteorological data collected during the California Regional PM₁₀/PM_2.5 Air Quality Study (CRPAQS). The UCD/CIT mechanistic air quality model was used with explicit decomposition of the gas phase reaction chemistry to track source contributions to secondary PM. Inert artificial tracers were used with an internal mixture representation to track source contributions to primary PM. Both primary and secondary source apportionment calculations were performed for 15 size fractions ranging from 0.01 to 10 μm particle diameters. Primary and secondary source contributions were resolved for fugitive dust, road dust, diesel engines, catalyst equipped gasoline engines, non-catalyst equipped gasoline engines, wood burning, food cooking, high sulfur fuel combustion, and other anthropogenic sources.Diesel engines were identified as the largest source of secondary nitrate in central California during the study episode, accounting for approximately 40% of the total PM_2.5 nitrate. Catalyst equipped gasoline engines were also significant, contributing approximately 20% of the total secondary PM_2.5 nitrate. Agricultural sources were the dominant source of secondary ammonium ion. Sharp gradients of PM concentrations were predicted around major urban areas. The relative source contributions to PM_2.5 from each source category in urban areas differ from those in rural areas, due to the dominance of primary OC in urban locations and secondary nitrate in the rural areas. The source contributions to ultra-fine particle mass PM_0.1 also show clear urban/rural differences. Wood smoke was found to be the major source of PM_0.1 in urban areas while motor vehicle sources were the major contributor of PM_0.1 in rural areas, reflecting the influence from two major highways that transect the Valley.     

Particulate Matter in California: Part 2—Spatial,Temporal, and Compositional Patterns of PM2.5, PM10–2.5, and PM10

Abstract

Geographic and temporal variations in the concentration and composition of particulate matter (PM) provide important insights into particle sources, atmospheric processes that influence particle formation, and PM management strategies. In the nonurban areas of California, annual-average PM_2.5 and PM₁₀ concentrations range from 3 to 10 [H9262]g/m³ and from 5 to 18 µg/m³, respectively. In the urban areas of California, annual-averages for PM_2.5 range from 7 to 30 [H9262]g/m³, with observed 24-hr peaks reaching levels as high as 160 [H9262]g/m³. Within each air basin, exceedances are a mixture of isolated events as well as periods of elevated PM_2.5 concentrations that are more prolonged and regional in nature. PM_2.5 concentrations are generally highest during the winter months. The exception is the South Coast Air Basin, where fairly high values occur throughout the year. Annual-average PM_2.5 mass, as well as the concentrations of major components, declined from 1988 to 2000. The declines are especially pronounced for the sulfate (SO₄ ^2?) and nitrate (NO₃ ^?) components of PM_2.5 and PM₁₀ and correlate with reductions in ambient levels of oxides of sulfur (SO_x) and oxides of nitrogen (NO_x). Annual averages for PM_10–2.5 and PM₁₀ exhibited similar downwind trends from 1994 to 1999, with a slightly less pronounced decrease in the coarse fraction.     

Spatial and temporal variations in PM10 and PM2.5 source contributions and comparison to emissions during the 1995 integrated monitoring study

The ambient PM₁₀ and PM_2.5 data collected during the fall and winter portions of the 1995 Integrated Monitoring Study (IMS95) were used to conduct Chemical Mass Balance (CMB) Modeling to determine source contribution estimates. Data from the core and saturation monitoring sites provided an extensive database for evaluating the spatial and temporal variations of contributing sources. Geological sources dominated fall samples, while secondary ammonium nitrate and carbonaceous sources were the largest contributors for winter samples. Secondary ammonium nitrate concentrations were uniform across all sites during both the fall and winter. Site-to-site variability was primarily due to differences in geological contributions in the fall, and carbonaceous source contributions in the winter. During the winter, diurnal profiles of particulate matter (PM) were driven by variations in carbonaceous sources at urban sites, and by variations in secondary ammonium nitrate at rural sites. Although records of day-specific PM activities were recorded during the study, no correlation was observed between 24-h CMB results and specific activities. The ambient data collected during IMS95 was also used to evaluate the adequacy of the emissions inventory. Comparison of ambient and emissions based ratios of NMHC/NO_x, PM/NO_x, CO/NO_x, and SO_x/NO_x suggested that emissions of NMHC and CO in some locations may be underestimated, while emissions for PM and SO_x may be overestimated. Comparison of fractional primary CMB source contribution estimates to corresponding fractional emissions estimates indicated that geological sources were overemphasized in the inventory, while carbonaceous sources were underrepresented.     

Development and Evaluation of a Continuous Coarse (PM10–PM25) Particle Monitor

ABSTRACT

In this paper, we describe the development and laboratory and field evaluation of a continuous coarse (2.5-10 um) particle mass (PM) monitor that can provide reliable measurements of the coarse mass (CM) concentrations in time intervals as short as 5-10 min. The operating principle of the monitor is based on enriching CM concentrations by a factor of ~25 by means of a 2.5-um cut point round nozzle virtual impactor while maintaining fine mass (FM)—that is, the mass of PM_{2 5} at ambient concentrations. The aerosol mixture is subsequently drawn through a standard tapered element oscillating microbalance (TEOM), the response of which is dominated by the contributions of the CM, due to concentration enrichment. Findings from the field study ascertain that a TEOM coupled with a PM₁₀ inlet followed by a 2.5-um cut point round nozzle virtual impactor can be used successfully for continuous CM concentration measurements. The average concentration-enriched CM concentrations measured by the TEOM were 26-27 times higher than those measured by the time-integrated PM₁₀ samplers [the micro-orifice uniform deposit     

Analysis of PM2.5and PM10 in the Atmosphere of Mexico City during 2000-2002

Abstract

During the last 10 years, high atmospheric concentrations of airborne particles recorded in the Mexico City metropolitan area have caused concern because of their potential harmful effects on human health. Four monitoring campaigns have been carried out in the Mexico City metropolitan area during 2000-2002 at three sites: (1) Xalos-toc, located in an industrial region; (2) La Merced, located in a commercial area; and (3) Pedregal, located in a residential area. Results of gravimetric and chemical analyses of 330 samples of particulate matter (PM) with an aerodynamic diameter less than 2.5 μm (PM_2.5) and PM with an aerodynamic diameter less than 10 μm (PM₁₀) indicate that (1) PM_2.5/PM₁₀ average ratios were 0.42, 0.46, and 0.52 for Xalostoc, La Merced, and Pedregal, respectively; (2) the highest PM_2.5 and PM₁₀ concentrations were found at the industrial site; (3) PM_2.5 and PM₁₀ concentrations were lower at nighttime; (4) PM_2.5 and PM₁₀ spatial averages concentrations were 35 and 76 μg/m³, respectively; and (5) when the PM_2.5 standard was exceeded, nitrate, sulfate, ammonium, organic carbon, and elemental carbon concentrations were high. Twenty-four hour averaged PM_2.5 concentrations in Mexico City and Sao Paulo were similar to those recorded in the 1980s in Los Angeles. PM₁₀ concentrations were comparable in Sao Paulo and Mexico City but 3-fold lower than those found in Santiago.     

Wintertime Vertical Variations in Particulate Matter (PM) and Precursor Concentrations in the San Joaquin Valley during the California Regional Coarse PM/Fine PM Air Quality Study

Abstract

Air quality monitoring was conducted at a rural site with a tower in the middle of California’s San Joaquin Valley (SJV) and at elevated sites in the foothills and mountains surrounding the SJV for the California Regional PM₁₀/M_2.5 Air Quality Study. Measurements at the surface and on a tower at 90 m were collected in Angiola, CA, from ecember 2000 through February 2001 and included hourly black carbon (BC), particle counts from optical particle counters, nitric oxide, ozone, temperature, relative humidity, wind speed, and direction. Boundary site measurements were made primarily using 24-hr integrated particulate matter (PM) samples. These measurements were used to understand the vertical variations of PM and PM precursors, the effect of stratification in the winter on concentrations and chemistry aloft and at the surface, and the impact of aloft-versus-surface transport on PM concentrations. Vertical variations of concentrations differed among individual species. The stratification may be important to atmospheric chemistry processes, particularly nighttime nitrate formation aloft, because NO₂ appeared to be oxidized by ozone in the stratified aloft layer. Additionally, increases in accumulation-mode particle concentrations in the aloft layer during a fine PM (PM_2.5) episode corresponded with increases in aloft nitrate, demonstrating the likelihood of an aloft nighttime nitrate formation mechanism. Evidence of local transport at the surface and regional transport aloft was found; transport processes also varied among the species. The distribution of BC appeared to be regional, and BC was often uniformly mixed vertically. Overall, the combination of time-resolved tower and surface measurements provided important insight into PM stratification, formation, and transport.