Radical precursors and related species from traffic as observed and modeled at an urban highway junction

Nitrous acid (HONO) and formaldehyde (HCHO) are important precursors for radicals and are believed to favor ozone formation significantly. Traffic emission data for both compounds are scarce and mostly outdated. A better knowledge of today's HCHO and HONO emissions related to traffic is needed to refine air quality models. Here the authors report results from continuous ambient air measurements taken at a highway junction in Houston, Texas, from July 15 to October 15, 2009. The observational data were compared with emission estimates from currently available mobile emission models (MOBILE6; MOVES [MOtor Vehicle Emission Simulator]). Observations indicated a molar carbon monoxide (CO) versus nitrogen oxides (NO_x) ratio of 6.01 ± 0.15 (r ² = 0.91), which is in agreement with other field studies. Both MOBILE6 and MOVES overestimate this emission ratio by 92% and 24%, respectively. For HCHO/CO, an overall slope of 3.14 ± 0.14 g HCHO/kg CO was observed. Whereas MOBILE6 largely underestimates this ratio by 77%, MOVES calculates somewhat higher HCHO/CO ratios (1.87) than MOBILE6, but is still significantly lower than the observed ratio. MOVES shows high HCHO/CO ratios during the early morning hours due to heavy-duty diesel off-network emissions. The differences of the modeled CO/NO_x and HCHO/CO ratios are largely due to higher NO_x and HCHO emissions in MOVES (30% and 57%, respectively, increased from MOBILE6 for 2009), as CO emissions were about the same in both models. The observed HONO/NO_x emission ratio is around 0.017 ± 0.0009 kg HONO/kg NO_x which is twice as high as in MOVES. The observed NO₂/NO_x emission ratio is around 0.16 ± 0.01 kg NO₂/kg NO_x, which is a bit more than 50% higher than in MOVES. MOVES overestimates the CO/CO₂ emission ratio by a factor of 3 compared with the observations, which is 0.0033 ± 0.0002 kg CO/kg CO₂. This as well as CO/NO_x overestimation is coming from light-duty gasoline vehicles.

Implications: Nitrous acid (HONO) and formaldehyde (HCHO) are important precursors for radicals that ultimately contribute to ozone formation. There still exist uncertainties in emission sources of HONO and HCHO and thus regional air quality modeling still tend to underestimate concentrations of free radicals in the atmosphere. This paper demonstrates that the latest U.S. Environmental Protection Agency (EPA) traffic emission model MOVES still shows significant deviations from observed emission ratios, in particular underestimation of HCHO/CO and HONO/NO_x ratios. Improving the performance of MOVES may improve regional air quality modeling.     

Comparison of the MOVES2010a,MOBILE6.2, and EMFAC2007 mobile source emission models with on-road traffic tunnel and remote sensing measurements

The Desert Research Institute conducted an on-road mobile source emission study at a traffic tunnel in Van Nuys, California, in August 2010 to measure fleet-averaged, fuel-based emission factors. The study also included remote sensing device (RSD) measurements by the University of Denver of 13,000 vehicles near the tunnel. The tunnel and RSD fleet-averaged emission factors were compared in blind fashion with the corresponding modeled factors calculated by ENVIRON International Corporation using U.S. Environmental Protection Agency's (EPA's) MOVES2010a (Motor Vehicle Emissions Simulator) and MOBILE6.2 mobile source emission models, and California Air Resources Board's (CARB's) EMFAC2007 (EMission FACtors) emission model. With some exceptions, the fleet-averaged tunnel, RSD, and modeled carbon monoxide (CO) and oxide of nitrogen (NO_x) emission factors were in reasonable agreement (±25%). The nonmethane hydrocarbon (NMHC) emission factors (specifically the running evaporative emissions) predicted by MOVES were insensitive to ambient temperature as compared with the tunnel measurements and the MOBILE- and EMFAC-predicted emission factors, resulting in underestimation of the measured NMHC/NO_x ratios at higher ambient temperatures. Although predicted NMHC/NO_x ratios are in good agreement with the measured ratios during cooler sampling periods, the measured NMHC/NO_x ratios are 3.1, 1.7, and 1.4 times higher than those predicted by the MOVES, MOBILE, and EMFAC models, respectively, during high-temperature periods. Although the MOVES NO_x emission factors were generally higher than the measured factors, most differences were not significant considering the variations in the modeled factors using alternative vehicle operating cycles to represent the driving conditions in the tunnel. The three models predicted large differences in NO_x and particle emissions and in the relative contributions of diesel and gasoline vehicles to total NO_x and particulate carbon (TC) emissions in the tunnel.

Implications: Although advances have been made to mobile source emission models over the past two decades, the evidence that mobile source emissions of carbon monoxide and hydrocarbons in urban areas were underestimated by as much as a factor of 2–3 in past inventories underscores the need for on-going verification of emission inventories. Results suggest that there is an overall increase in motor vehicle NMHC emissions on hot days that is not fully accounted for by the emission models. Hot temperatures and concomitant higher ratios of NMHC emissions relative to NO_x both contribute to more rapid and efficient formation of ozone. Also, the ability of EPA's MOVES model to simulate varying vehicle operating modes places increased importance on the choice of operating modes to evaluate project-level emissions.     

Use of Subsampled Traffic Data to Estimate Roadway Emissions,Including Conversion to MOBILE6 Vehicle Classifications

Abstract

Air quality is degraded by many factors, among which the emissions from on‐road vehicles play a significant role. Timely and accurate estimate of such emissions becomes very important for policy‐making and effective control measures. However, lack of traffic data and outdated emission software make this task difficult. This research has demonstrated a new method that facilitates the vehicular emission inventories at the local level by using shorter-time Highway Performance Monitoring System (HPMS) traffic data along with the latest U.S. Environment Protection Agency (EPA) emission modeling software, MOBILE6. The conversion methodology was developed for converting readily available HPMS traffic volume data into EPA MOBILE-based traffic classifications, and a corresponding software program was written for automating the process. EPA MOBILE6 model was used to obtain emissions of nitrogen oxides (NO_x), volatile organic compound (VOC), and cabon monoxide (CO) emitted by the parent traffic and subsampled traffic data, and these emissions were additionally compared. The case study has shown that the difference of the magnitude between the emission estimates produced by certain subsampled and parent traffic data are minor, indicating that subsampled HPMS data can be used for reporting parent traffic emissions. It was also observed that traffic emissions follow a Weibull distribution, and NO_x emissions were more sensitive to the traffic data composition than VOC and CO. Lastly, use of average emission values of 20 or 30 consecutive minutes appears to be valid for representing hourly emissions.     

Multispecies remote sensing measurements of vehicle emissions on Sherman Way in Van Nuys,California

As part of the 2010 Van Nuys tunnel study, researchers from the University of Denver measured on-road fuel-specific light-duty vehicle emissions from nearly 13,000 vehicles on Sherman Way (0.4 miles west of the tunnel) in Van Nuys, California, with its multispecies Fuel Efficiency Automobile Test (FEAT) remote sensor a week ahead of the tunnel measurements. The remote sensing mean gram per kilogram carbon monoxide (CO), hydrocarbon (HC), and oxide of nitrogen (NO_x) measurements are 8.9% lower, 41% higher, and 24% higher than the tunnel measurements, respectively. The remote sensing CO/NO_x and HC/NO_x mass ratios are 28% lower and 20% higher than the comparable tunnel ratios. Comparisons with the historical tunnel measurements show large reductions in CO, HC, and NO_x over the past 23 yr, but little change in the HC/NO_x mass ratio since 1995. The fleet CO and HC emissions are increasingly dominated by a few gross emitters, with more than a third of the total emissions being contributed by less than 1% of the fleet. An example of this is a 1995 vehicle measured three times with an average HC emission of 419 g/kg fuel (two-stroke snowmobiles average 475 g/kg fuel), responsible for 4% of the total HC emissions. The 2008 economic downturn dramatically reduced the number of new vehicles entering the fleet, leading to an age increase (>1 model year) of the Sherman Way fleet that has increased the fleet's ammonia (NH₃) emissions. The mean NH₃ levels appear little changed from previous measurements collected in the Van Nuys tunnel in 1993. Comparisons between weekday and weekend data show few fleet differences, although the fraction of light-duty diesel vehicles decreased from the weekday (1.7%) to Saturday (1.2%) and Sunday (0.6%).

Implications: On-road remote sensing emission measurements of light-duty vehicles on Sherman Way in Van Nuys, California, show large historical emission reductions for CO and HC emissions despite an older fleet arising from the 2008 economic downturn. Fleet CO and HC emissions are increasingly dominated by a few gross emitters, with a single 1995 vehicle measured being responsible for 4% of the entire fleet's HC emissions. Finding and repairing and/or scrapping as little as 2% of the fleet would reduce on-road tailpipe emissions by as much as 50%. Ammonia emissions have locally increased with the increasing fleet age.     

Comparison of the SCAQS Tunnel Study with Other On Road Vehicle Emission Data

The Van Nuys Tunnel experiment conducted in 1987 by Ingalls et al. (see A&WMA Paper 89-137.3), to verify automotive emission inventories as part of the Southern California Air Quality Study (SCAQS), gave higher CO and HC emission-rate values than expected on the basis of automotive-emission models—by factors of approximately 3 and 4, respectively. The CO/NO_X and HC/NO_X emission-rate ratios moreover were higher than expected—by similar factors (NO_X emission rates were about as expected). The purpose of the present paper is to review the literature on dynamometer and on-road (in tunnels and along roadways) testing of in-use vehicles, and on urban-air CO/HC/NO_X concentration ratios, to see whether the Van Nuys Tunnel results are reasonable in terms of previous experience. The conclusions are that (1) on-road CO and HC emissions higher than expected have been reported before, (2) on-road CO and HC emissions consistent with the Van Nuys Tunnel results have been reported before, and (3) on-road CO/NO_X and HC/NO_X emission-rate ratios higher than expected have been reported before. The Van Nuys Tunnel NO_X results actually are lower than in other on-road experiments, and the CO/NO_X and HC/NO_X ratios consequently are higher. The higher-than-predicted CO/NO_X and HC/NO_X ratios at Van Nuys and other on-road sites suggest richer operation on-road than predicted or than observed in the inuse- vehicle dynamometer tests which serve as the model inputs. Support for these suggestions and conclusions is found in comparison of urban-air and emission-inventory HC/NO_X ratios.     

Assessment of vehicular pollution in China

As the motor vehicle population in China continues to increase at an annual rate of approximately 15%, air pollution related to vehicular emissions has become the focus of attention, especially in large cities. There is an urgent need to identify the severity of this pollution in China. Based on an investigation into vehicle service characteristics, this study used a series of driving cycle tests of in-use Chinese motor vehicles for their emission factors in laboratories, which indicated that CO and HC emission factors are 5-10 times higher, and NOx 2-5 times higher, than levels in developed countries. The MOBILE5 model was adapted to the Chinese situation and used to calculate the emission of pollutants from motor vehicles. Results show that vehicle emission is concentrated in major cities, such as Beijing, Guangzhou, Shanghai, and Tianjin. Motor vehicle emissions contribute a significant proportion of pollutants in those cities, with contribution rates of CO and NOx greater than 80% and 40%, respectively, in Beijing and Guangzhou. Urban air quality is far worse than the national ambient air quality standard. In conclusion, although China has a relatively small number of motor vehicles, most of them are concentrated within metropolitan areas, and their emissions are closely related to urban air pollution problems in large cities.     

Idle Emissions from Heavy-Duty Diesel and Natural Gas Vehicles at High Altitude

ABSTRACT

Idle emissions of total hydrocarbon (THC), CO, NO_x, and particulate matter (PM) were measured from 24 heavy-duty diesel-fueled (12 trucks and 12 buses) and 4 heavy-duty compressed natural gas (CNG)-fueled vehicles. The volatile organic fraction (VOF) of PM and aldehyde emissions were also measured for many of the diesel vehicles. Experiments were conducted at 1609 m above sea level using a full exhaust flow dilution tunnel method identical to that used for heavy-duty engine Federal Test Procedure (FTP) testing. Diesel trucks averaged 0.170 g/min THC, 1.183 g/min CO, 1.416 g/min NO_x, and 0.030 g/min PM. Diesel buses averaged 0.137 g/min THC, 1.326 g/min CO, 2.015 g/min NO_x, and 0.048 g/min PM.

Results are compared to idle emission factors from the MOBILE5 and PART5 inventory models. The models significantly (45-75%) overestimate emissions of THC and CO in comparison with results measured from the fleet of vehicles examined in this study. Measured NO_x emissions were significantly higher (30-100%) than model predictions. For the pre-1999 (pre-consent decree) truck engines examined in this study, idle NO_x emissions increased with Health and Environment; June 30, 1999 (available from the authors).     

Near-road air pollutant concentrations of CO and PM2.5: A comparison of MOBILE6.2/CALINE4 and generalized additive models

The contribution of vehicular traffic to air pollutant concentrations is often difficult to establish. This paper utilizes both time-series and simulation models to estimate vehicle contributions to pollutant levels near roadways. The time-series model used generalized additive models (GAMs) and fitted pollutant observations to traffic counts and meteorological variables. A one year period (2004) was analyzed on a seasonal basis using hourly measurements of carbon monoxide (CO) and particulate matter less than 2.5 μm in diameter (PM_2.5) monitored near a major highway in Detroit, Michigan, along with hourly traffic counts and local meteorological data. Traffic counts showed statistically significant and approximately linear relationships with CO concentrations in fall, and piecewise linear relationships in spring, summer and winter. The same period was simulated using emission and dispersion models (Motor Vehicle Emissions Factor Model/MOBILE6.2; California Line Source Dispersion Model/CALINE4). CO emissions derived from the GAM were similar, on average, to those estimated by MOBILE6.2. The same analyses for PM_2.5 showed that GAM emission estimates were much higher (by 4–5 times) than the dispersion model results, and that the traffic-PM_2.5 relationship varied seasonally. This analysis suggests that the simulation model performed reasonably well for CO, but it significantly underestimated PM_2.5 concentrations, a likely result of underestimating PM_2.5 emission factors. Comparisons between statistical and simulation models can help identify model deficiencies and improve estimates of vehicle emissions and near-road air quality.     

Estimations of Real-World N2O Emissions from Road Vehicles by Means of Measurements in a Traffic Tunnel

Abstract

Ambient air measurements of N₂O, NO_x, CO, and HC based on grab sampling were conducted in a major traffic tunnel in Sweden, that carries up to 4,000 vehicles per hour, in order to estimate real-world emissions of N₂O for road traffic. Two different methods—relative and mass balance—were used to calculate a N₂O emission factor for the mixed vehicle fleet, which gave an average emission factor, at average speeds of 30-70 km/h, of approximately 25 mg N₂O/ km, with a range of 7-56 mg/km.     

Real-world vehicle emissions and VOCs profile in the Taipei tunnel located at Taiwan Taipei area

An in situ field experiment was conducted in a highway road tunnel in the Taipei City to determine the motor vehicle emission factors (EF) of different kinds of air pollution species. These are carbon monoxide (CO), oxides of nitrogen (NO_x), non-methane hydrocarbons (NMHC) and VOCs species. About 56 species of VOCs were sampled by canister sampler and followed by the GC-MS analyzing. Furthermore, the tunnel-drafting rate was determined by SF₆ tracer method.The EF for the highway vehicles determined from this experiment are 3.64, 0.90, 0.44 and 0.24 gm km⁻¹ veh⁻¹ for CO, NO_x, NMHC and the totally measured VOCs, respectively. A comparison of the EFs from the road tunnel experiment to the estimates by the USEPA MOBILE5b (M5b) and the modified Taiwan EPA MOBILE-TAIWAN2.0 (MT2.0) provides a first-hand evaluation of the model characteristics. M5b and MT2.0 both tend to underpredict CO by 10% and 20%, respectively. While M5b overpredicts NO_x and NMHC by 40% and 20%, respectively; MT2.0 has fairly good predictions for these two species. From the GC-MS analysis of the canister samples, it was found that the most abundant species from the traffic-emitted VOCs in Taipei road tunnel are toluene, ethene and 1,2,4-trimethyl-benzene (1,2,4-TMB) by the weight basis. However, ethene, acetylene and toluene are the most abundant in VOCs based on volume. The VOCs’ weight composition in terms of the carbon bond classification is 28% by the paraffins, 33% by the olefins and 39% by the aromatics, respectively. In order to evaluate the ozone formation potential from the typical road emission in Taipei area, the maximum increment reactivity is calculated. It was found that about 1015 mg of O₃ is induced by per vehicle per kilometer traveled emission. Among them, ethene, 1,2,4-TMB and propene from the road vehicle's emission contribute most to the ozone-formation reactivity.     

A Multipurpose Flare Stack for Control of Chemical Process Wastes

Abstract

To test the effectiveness of California’s vehicle inspection/ maintenance (I/M) program, exclusive of vehicle-owner intervention, a fleet of more than 1,100 vehicles that previously had failed California’s Smog Check test were sent to randomly selected Smog Check stations in the Los Angeles area for covert inspections and repairs. The two-speed idle test was used for repairs. For those vehicles that were repaired at the first inspection, their FTP emission reductions were 25%, 14%, and 11% for hydrocarbons (HC), carbon monoxide (CO), and nitrogen oxides (NO_x), respectively, although emissions testing for NO_x was not performed at the Smog Check stations. Idle HC and CO emissions increased for 35% and 43% of the vehicles, respectively, after repairs. This data set shows that most vehicles that fail the Smog Check inspection are only marginal emitters, with 61% and 44% of the total potential for HC and CO emission reductions, respectively, coming from only 10% of the vehicles that currently fail the inspection. When the vehicles were rank-ordered by idle emissions from dirtiest to cleanest, emission reduction costs for the highest-emitting 10% of the fleet averaged $l,100/ton and $250/ton for HC and CO, respectively, attributing all the costs to each pollutant exclusively. For the remaining vehicles, costs increased dramatically.     

On-road remote sensing measurements and fuel-based motor vehicle emission inventory in Hangzhou,China

Motor vehicles are one of the largest sources of air pollutants worldwide. Despite their importance, motor vehicle emissions are inadequately understood and quantified, esp. in developing countries. In this study, the real-world emissions of carbon monoxide (CO), hydrocarbons (HC) and nitrogen oxide (NO) were measured using an on-road remote sensing system at five sites in Hangzhou, China in 2004 and 2005. Average emission factors of CO, HC and NO_x for petrol vehicles of different model year, technology class and vehicle type were calculated in grams of pollutant per unit of fuel use (g l⁻¹) from approximately 32,260 petrol vehicles. Because the availability of data used in traditional on-road mobile source estimation methodologies is limited in China, fuel-based approach was implemented to estimate motor vehicle emissions using fuel sales as a measure of vehicle activity, and exhaust emissions factors from remote sensing measurements. The fuel-based exhaust emission inventories were also compared with the results from the recent international vehicle emission (IVE) model. Results show that petrol vehicle fleet in Hangzhou has significantly high CO emissions, relatively high HC and low NO_x, with the average emission factors of 193.07±15.63, 9.51±2.40 and 5.53±0.48 g l⁻¹, respectively. For year 2005 petrol vehicles exhaust emissions contributed with 182,013±16,936, 9107±2255 and 5050±480 metric ton yr⁻¹ of CO, HC and NO_x, respectively. The inventories are 45.5% higher, 6.6% higher and 53.7% lower for CO, HC and NO_x, respectively, than the estimates using IVE travel-based model. In addition, a number of insights about the emission distributions and formation mechanisms have been obtained from an in-depth analysis of these results.     

Real-world emissions of in-use off-road vehicles in Mexico

Off-road vehicles used in construction and agricultural activities can contribute substantially to emissions of gaseous pollutants and can be a major source of submicrometer carbonaceous particles in many parts of the world. However, there have been relatively few efforts in quantifying the emission factors (EFs) and for estimating the potential emission reduction benefits using emission control technologies for these vehicles. This study characterized the black carbon (BC) component of particulate matter and NOx, CO, and CO₂ EFs of selected diesel-powered off-road mobile sources in Mexico under real-world operating conditions using on-board portable emissions measurements systems (PEMS). The vehicles sampled included two backhoes, one tractor, a crane, an excavator, two front loaders, two bulldozers, an air compressor, and a power generator used in the construction and agricultural activities. For a selected number of these vehicles the emissions were further characterized with wall-flow diesel particle filters (DPFs) and partial-flow DPFs (p-DPFs) installed. Fuel-based EFs presented less variability than time-based emission rates, particularly for the BC. Average baseline EFs in working conditions for BC, NOx, and CO ranged from 0.04 to 5.7, from 12.6 to 81.8, and from 7.9 to 285.7 g/kg-fuel, respectively, and a high dependency by operation mode and by vehicle type was observed. Measurement-base frequency distributions of EFs by operation mode are proposed as an alternative method for characterizing the variability of off-road vehicles emissions under real-world conditions. Mass-based reductions for black carbon EFs were substantially large (above 99%) when DPFs were installed and the vehicles were idling, and the reductions were moderate (in the 20–60% range) for p-DPFs in working operating conditions. The observed high variability in measured EFs also indicates the need for detailed vehicle operation data for accurately estimating emissions from off-road vehicles in emissions inventories.

Implications: Measurements of off-road vehicles used in construction and agricultural activities in Mexico using on-board portable emissions measurements systems (PEMS) showed that these vehicles can be major sources of black carbon and NO_X. Emission factors varied significantly under real-world operating conditions, suggesting the need for detailed vehicle operation data for accurately estimating emissions inventories. Tests conducted in a selected number of sampled vehicles indicated that diesel particle filters (DPFs) are an effective technology for control of diesel particulate emissions and can provide potentially large emissions reduction in Mexico if widely implemented.     

Evaluating Speed Differences between Passenger Vehicles and Heavy Trucks for Transportation-Related Emissions Modeling

Abstract

Heavy-duty trucks make up only 3% of the on-road vehicle fleet, yet they account for >7% of vehicle miles traveled in the United States. They also contribute a significant proportion of regulated ambient emissions. Heavy vehicles emit emissions at different rates than passenger vehicles. They may also behave differently on‐road, yet may be treated similarly to passenger vehicles in emissions modeling. Input variables to the MOBILE software, such as average vehicle speed, are typically specified the same for heavy trucks as for passenger vehicles. Although not frequently considered in modeling emissions, speed differences between passenger vehicles and heavy trucks may influence emissions, because emission rates are correlated to average speed. Differences were evaluated by collecting average and spot speeds for heavy trucks and passenger vehicles on arterials and spot speeds on freeways in Des Moines, IA, and Minneapolis/St. Paul, MN. Speeds were compared by study site. Space mean speeds for heavy trucks were lower than passenger vehicle speeds for all of the arterials with differences ranging from 0.8 to 19 mph. Spot speeds for heavy trucks were also lower at all of the arterial and freeway locations with differences ranging from 0.8 to 6.1 mph. The impact that differences in on‐road speeds had on emissions was also evaluated using MOBILE version 6.2. Misspecification of average truck speed is the most significant at lower and higher speed ranges.     

Evaporative traffic hydrocarbon emissions,traffic CO and speciated HC traffic emissions from the city of Athens

Quasi-continuous measurements of NO_x, CO and C₅–C₁₂ hydrocarbons made during the MEDCAPHOT-TRACE experiment in a street canyon with heavy traffic load were used to estimate the CO/NO_x and 36 individual NMHC/NO_x traffic emission ratios in the Athens basin. A traffic emission inventory has been compiled for Athens and aspects of this inventory were tested against measurements. The results indicate that although the main features of the 9:00 to 15:00 variations of the NMHC/NO_x and CO/NO_x inventory emission ratios are in agreement with observations, during the rest of the day the fine structure of the variations of these ratios cannot be accurately predicted by the inventory. Comparison of pollutant emission ratios derived from ambient measurements with emission ratios predicted by existing inventories for Athens reveals serious discrepancies. Further, the experimental results and theoretical considerations indicate that the speciation of evaporative emissions changes with increasing ambient temperature in favour of the most volatile HC species, thus changing the speciation of traffic emissions during the course of the day. This is an aspect that is not taken into account in present urban photochemical modelling inventories.     

Vehicle emissions of radical precursors and related species observed in the 2009 SHARP campaign

The 2009 Study of Houston Atmospheric Radical Precursors (SHARP) field campaign had several components that yielded information on the primary vehicular emissions of formaldehyde (HCHO) and nitrous acid (HONO), in addition to many other species. Analysis of HONO measurements at the Moody Tower site in Houston, TX, yielded emission ratios of HONO to the vehicle exhaust tracer species NO_x and CO of 14 pptv/ppbv and 2.3 pptv/ppbv, somewhat smaller than recently published results from the Galleria site, although evidence is presented that the Moody Tower values should be upper limits to the true ratios of directly emitted HONO, and are consistent with ratios used in current standard emissions models. Several other Moody Tower emission ratios are presented, in particular a value for HCHO/CO of 2.4 pptv/ppbv. Considering only estimates of random errors, this would be significantly lower than a previous value, though the small sample size and possible systematic differences should be taken into account. Emission factors for CO, NO_x, and HCHO, as well as various volatile organic compounds (VOCs), were derived from mobile laboratory measurements both in the Washburn Tunnel and in on-road exhaust plume observations. These two sets of results and others reported in the literature all agree well, and are substantially larger than the CO, NO_x, and HCHO emission factors derived from the emission ratios reported from the Galleria site.

Implications: Emission factors for the species measured in the various components of the 2009 SHARP campaign in Houston, TX, including HCHO, HONO, CO, CO₂, nitrogen oxides, and VOCs, are needed to support regional air quality monitoring. Components of the SHARP campaign measured these species in several different ways, each with their own potential for systematic errors and differences in vehicle fleets sampled. Comparisons between data sets suggest that differences in sampling place and time may result in quite different emission factors, while also showing that different vehicle mixes can yield surprisingly similar emission factors.     

On-Road,In-Use Gaseous Emission Measurements by Remote Sensing of School Buses Equipped with Diesel Oxidation Catalysts and Diesel Particulate Filters

Abstract

A remote sensing device was used to obtain on-road and in-use gaseous emission measurements from three fleets of schools buses at two locations in Washington State. This paper reports each fleet’s carbon monoxide (CO), hydrocarbon (HC), nitric oxide (NO), and nitrogen dioxide (NO₂) mean data. The fleets represent current emission retrofit technologies, such as diesel particulate filters and diesel oxidation catalysts, and a control fleet. This study shows that CO and HC emissions decrease with the use of either retrofit technology when compared with control buses of the same initial emission standards. The CO and HC emission reductions are consistent with published U.S. Environmental Protection Agency verified values. The total oxides of nitrogen (NO_x), NO, and the NO₂/NO_x ratio all increase with each retrofit technology when compared with control buses. As was expected, the diesel particulate filters emitted significantly higher levels of NO₂ than the control fleet because of the intentional conversion of NO to NO₂ by these systems. Most prior research suggests that NO_x emissions are unaffected by the retrofits; however, these previous studies have not included measurements from retrofit devices on-road and after nearly 5 yr of use. Two 2006 model-year buses were also measured. These vehicles did not have retrofit devices but were built to more stringent new engine standards. Reductions in HCs and NO_x were observed for these 2006 vehicles in comparison to other non-retrofit earlier model-year vehicles.     

Effects of improved spatial and temporal modeling of on-road vehicle emissions

Numerous emission and air quality modeling studies have suggested the need to accurately characterize the spatial and temporal variations in on-road vehicle emissions. The purpose of this study was to quantify the impact that using detailed traffic activity data has on emission estimates used to model air quality impacts. The on-road vehicle emissions are estimated by multiplying the vehicle miles traveled (VMT) by the fleet-average emission factors determined by road link and hour of day. Changes in the fraction of VMT from heavy-duty diesel vehicles (HDDVs) can have a significant impact on estimated fleet-average emissions because the emission factors for HDDV nitrogen oxides (NOx) and particulate matter (PM) are much higher than those for light-duty gas vehicles (LDGVs). Through detailed road link-level on-road vehicle emission modeling, this work investigated two scenarios for better characterizing mobile source emissions: (1) improved spatial and temporal variation of vehicle type fractions, and (2) use of Motor Vehicle Emission Simulator (MOVES2010) instead of MOBILE6 exhaust emission factors. Emissions were estimated for the Detroit and Atlanta metropolitan areas for summer and winter episodes. The VMT mix scenario demonstrated the importance of better characterizing HDDV activity by time of day, day of week, and road type. More HDDV activity occurs on restricted access road types on weekdays and at nonpeak times, compared to light-duty vehicles, resulting in 5-15% higher NOx and PM emission rates during the weekdays and 15-40% lower rates on weekend days. Use of MOVES2010 exhaust emission factors resulted in increases of more than 50% in NOx and PM for both HDDVs and LDGVs, relative to MOBILE6. Because LDGV PM emissions have been shown to increase with lower temperatures, the most dramatic increase from MOBILE6 to MOVES2010 emission rates occurred for PM2.5 from LDGVs that increased 500% during colder wintertime conditions found in Detroit, the northernmost city modeled.     

Use of subsampled traffic data to estimate roadway emissions, including conversion to MOBILE6 vehicle classifications

Air quality is degraded by many factors, among which the emissions from on-road vehicles play a significant role. Timely and accurate estimate of such emissions becomes very important for policy-making and effective control measures. However, lack of traffic data and outdated emission software make this task difficult. This research has demonstrated a new method that facilitates the vehicular emission inventories at the local level by using shorter-time Highway Performance Monitoring System (HPMS) traffic data along with the latest U.S. Environment Protection Agency (EPA) emission modeling software, MOBILE6. The conversion methodology was developed for converting readily available HPMS traffic volume data into EPA MOBILE-based traffic classifications, and a corresponding software program was written for automating the process. EPA MOBILE6 model was used to obtain emissions of nitrogen oxides (NOx), volatile organic compound (VOC), and cabon monoxide (CO) emitted by the parent traffic and subsampled traffic data, and these emissions were additionally compared. The case study has shown that the difference of the magnitude between the emission estimates produced by certain subsampled and parent traffic data are minor, indicating that subsampled HPMS data can be used for reporting parent traffic emissions. It was also observed that traffic emissions follow a Weibull distribution, and NOx emissions were more sensitive to the traffic data composition than VOC and CO. Lastly, use of average emission values of 20 or 30 consecutive minutes appears to be valid for representing hourly emissions.