Inactivation of airborne Enterococcus faecalis and infectious bursal disease virus using a pilot-scale ultraviolet photocatalytic oxidation scrubber

High microbial concentrations and emissions associated with livestock houses raise health and environmental concerns. A pilot-scale ultraviolet photocatalytic oxidation (UV-PCO) scrubber was tested for its efficacy to inactivate aerosolized Enterococcus faecalis and infectious bursal disease virus (IBDV). Microbial reduction was determined by the difference in microbial concentrations measured in the upstream and downstream isolators that were connected to the two ends of the UV-PCO scrubber. Two UV irradiance levels were tested by using one or two UV lamps. The theoretical average UV irradiances were 6,595 µ W cm^?2 with one UV lamp and 12,799 µ W cm^?2 with two UV lamps. At the tested ventilation rate (70 m³ hr^?1), the contact time was 1 sec. Reduction rate and other two indexes (k-value and Z-value) that normalized UV radiation were calculated to describe the extent of microbial inactivation. The UV-PCO scrubber eliminated >99.7% of airborne E. faecalis from the incoming airstream under one UV lamp irradiance, and the reduction was further increased by 0.2–0.3% when the second UV lamp was added. The reduction rate for airborne IBDV was 72.4% with one UV lamp. The calculated k-values were 0.501–0.594 cm² mJ^?1 for airborne E. faecalis and 0.217 cm² mJ^?1 for IBDV. The Z-value of airborne E. faecalis to UV irradiance was 9.3 (±1.6)?×?10^?4 cm² µ W^?1 sec^?1. The results indicate that a UV-PCO scrubber can serve as an effective and efficient technology for inactivating airborne bacteria and virus. Scaling up of the pilot-scale scrubber for field use will require considerations such as design air treatment capacity, UV irradiance level, contact time, dust concentration, susceptibility of target microorganisms, and expected reduction rate.

Implications: This work demonstrated that a UV-PCO scrubber can be used to inactivate animal-associated airborne microorganisms, thus reducing microbial emissions from livestock houses and minimizing the biological impact to ambient environment. The microbial reduction efficiency by the UV-PCO scrubber varied depended on the level of UV irradiation and the target microbial species. The tested viral species (infectious bursal disease virus) was more resistant to the UV-PCO scrubber as compared to its counterpart bacterial species (E. faecalis).     

Photoenhanced toxicity of a weathered oil onCeriodaphnia dubia reproduction

Traditionally, the toxic effects of petroleum have been investigated by conducting studies in the absence of ultraviolet radiation (UV). Photomediated toxicity is often not considered, and the toxic effects of an oil spill can be grossly underestimated. The toxicity of a weathered oil collected from a monitoring well at an abandoned oil field toCeriodaphnia dubia was examined in the presence of UV. A solar simulator equipped with UVB, UVA, and cool white lamps was used to generate environmentally comparable solar radiation intensities.C. dubia were exposed to six concentrations of water accommodated fractions (WAF) of weathered oil in conjunction with three levels of laboratory simulated UV (Reference = < 0.002 μW/cm²UVB; 3.0 μW/cm² UVA; Low = 0.30 μW/cm² UVB; 75.0 μW/cm² UVA; High = 2.0 μW/cm² UVB; 340.0 μW/cm² UVA) and visible light. Seven day static renewal bioassays were used to characterize WAF/UV toxicity. WAF toxicity significantly (p < 0.05) increased when the organisms were exposed to WAF in the presence of UV. The photoenhanced toxicity of the WAF increased with WAF concentration within each UV regime. Relative to the reference light regime, the average number of neonates from adults exposed to 1.6 mg TPH/L decreased significantly by 20% within the low light regime, and by 60% within the high light regime. These results indicate that organisms exposed to dissolved-phase weathered oil in the presence of environmentally realistic solar radiation, exhibit 1.3–2.5 times greater sensitivity, relative to organisms exposed under traditional laboratory fluorescent lighting.     

Effect of UV radiation and temperature on mineralization and volatilization of coumaphos in water

This study was undertaken to determine the dissipation and degradation of coumaphos [O-(3-chloro-4-methyl-2-oxo-2H-1-benzopyran-7-yl) O,O-diethyl phosphorothioate] under different sunlight conditions and at different temperatures. The effect of the ultra violet (UV) component of solar radiation was also studied using quartz tubes in addition to other radiation in the visible range using glass tubes and the results were compared with those obtained under the dark light conditions. Water suspensions of coumaphos were incubated at three temperatures viz. 22°C, 37°C and 53°C in closed systems to study the effect of temperature. Volatilization, mineralization and degradation of coumaphos increased with an increase in temperature and exposure to solar radiation, particularly under the UV component of the solar radiation. Major loss of the pesticide occurred through volatilization. The optimum temperature for the degradation of coumaphos was found to be at 37°C. The data obtained from the mineralization and degradation studies indicated that 53°C crosses the biological range for suitable growth of microorganism. UV radiation exposure along with maintaining temperature at 37°C may prove useful in the dissipation and/or degradation of coumaphos prior to its disposal as waste from cattle dipping vats.     

Seasonal variation of PCDD/Fs in the metropolis of Istanbul,Turkey

Atmospheric concentrations of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/F) compounds were investigated at three different regions of Istanbul which reflect urban, urban/industrial, and sub-urban characteristics. Air samples were collected simultaneously for both gaseous and particulate phases using high volume samplers on monthly time intervals from May 2011 to October 2012. The highest concentrations (3,056 fg/m³ and 156 fg I-TEQ/m³) were observed at the sampling site that reflects traffic, residential, and industrial emission source characteristics, while the lowest concentrations (829 fg/m³ and 38 fg I-TEQ/m³) were observed at the sampling point which is far away from centrum and reflects sub-urban characteristics. Concentrations of PCDD congeners were, in general, found to be higher than PCDF congeners, and OCDD, 1,2,3,4,6,7,8-HpCDD/F, and OCDF congeners were recorded to be the most abundant congeners. Winter season concentrations were also found to be higher especially in particulate phase. As a result, combustion processes such as motor vehicles and residential heating equipment were thought to be the principal sources of emissions of PCDD/F compounds when both congener profiles and seasonal variations are considered. Basic statistical evaluation of the data resembled high degree of inverse correlations between PCDD/F concentrations and UV and solar radiation.     

Aircraft Release of Sulfur Hexafluoride as an Atmospheric Tracer

Abstract

The effect of temperature on polyvinylchloride (PVC) combustion using a downstream tubular furnace was investigated for the formation of polycylcic aromatic hydrocarbons (PAHs) and chlorinated compounds. As the temperature increased, higher levels of PAHs were generated. Chlorinated compounds reached a peak at 600°C, with low emissions recorded at 300 and 900°C. There was a close correlation (R² = 0.97) among polychlorinated bi-phenyls (PCBs), hexachlorobenzene, pentachloroben-zene, and polychlorinated dibenzo-p-dioxins and poly-chlorinated dibenzofurans (PCDD/Fs). PAHs at all temperatures were analyzed in the gas phase. PCDD/Fs and PCBs were emitted as a solid phase at 300 and 600°C and as a gas phase at 900°C. For some PAHs, chloroben-zenes, and PCDD/Fs, a mathematical equation between the gas and solid phase and the reciprocal temperature in semilog proportion was derived. The proposed equation, which is log (amount in gas phase/amount in solid phase) = ?A/T + B, where T is the temperature of the furnace and A and B are constants, for these species relating their gas/solid distributions showed a good relationship.     

Photocatalytic Degradation of an Organophosphorus Pesticide Phosalone in Aqueous Suspensions of Titanium Dioxide

Abstract

The present work deals with photocatalytic degradation of an organophosphorus pesticide, phosalone, in water in the presence of TiO₂ particles under UV light illumination (1000 W). The influence of the basic photocatalytic parameters such as pH of the solution, amount of TiO₂, irradiation time, stirring rate, and distance from UV source, on the photodegradation efficiency of phosalone was investigated. The degradation rate of phosalone was not high when the photolysis was carried out in the absence of TiO₂ and it was negligible in the absence of UV light. The half-life (DT₅₀) of a 20 ppm aqueous solution of phosalone was 15 min in optimized conditions. The plot of lnC (phosalone) vs. time was linear, suggesting first order reaction (K = 0.0532 min^?1). The half-life time of photomineralization in the concentration range of 7.5–20 ppm was 13.02 min. The efficiency of the method was also determined by measuring the reduction of Chemical Oxygen Demand (COD). During the mineralization under optimized conditions, COD decreased by more than 45% at irradiation time of 15 min. The photodegradation of phosalone was enhanced by addition of proper amount of hydrogen peroxide (150 ppm).     

Technical Session Preliminary Schedule Announced for 1988 APCA Annual Meeting

ABSTRACT

Stable heterogeneous catalysts for the oxidative removal of CO from air at ambient temperatures have been developed. An alumina support impregnated with PdCl₂, CuCl₂, and CuSO₄ is described. Optimal activity was obtained with Pd 0.020 mol/kg, Cu 0.50 mol/kg, CuCl₂ 20-30% of total Cu, a 2- to 24-hr soak, filtration of surplus raffinate, and a 2- to 4-hr firing in air at 200-350 °C. The catalysts are effective at 20-26 °C and relative humidities in the 15-90% range. They are reversibly deactivated by completely dry or water-saturated air streams. These catalysts have been tested at space velocities up to 30,000 hr^-1. In contact with <100 ppm CO, they are highly efficient, removing ~99% of the CO with contact times of ~120 msec (pseudo-first order k' > 25 sec^-1). At much higher CO concentrations, the maximum CO loading rate—limited by the Cu(I) reoxidation rate—is approximately 17 m mol CO per Limol Pd per hour.     

Kinetics of simazine advanced oxidation in water

Abstract

Comparison of the effects and kinetics of UV photolysis and four advanced oxidation systems (ozone, ozone/hydrogen peroxide, ozone/UV radiation and UV radiation/hydrogen peroxide) for the removal of simazine from water has been investigated. At the conditions applied, the order of reactivity was ozone < ozone/hydrogen peroxide < UV radiation < ozone/UV radiation and UV radiation/hydrogen peroxide. Rate constants of the reactions between ozone and simazine and hydroxyl radical and simazine were found to be 8.7 M^‐1s^‐1 and 2.1x10⁹ M^‐1s^‐1, respectively. Also, a quantum yield of 0.06 mol.photon^‐1 was found for simazine at 254 nm UV radiation. The high value of the quantum yield corroborated the importance of the direct photolysis process. Percentage contributions of direct reaction with ozone, reaction with hydroxyl radicals and direct photolysis were also quantified.     

Ground-based measurements and modeling of solar UV-B radiation in Lhasa,Tibet

We present results from measurements by a NILU-UV Irradiance Meter of solar UV-B radiation in Lhasa, Tibet for the period from 7 July 1999 to 17 November 2002. The measured maximum UV-B dose rate was 1.50 W/m² during the winter, and 3.96 W/m², during the summer. The clear-sky values were below 3.00 W/m². Comparisons between measured and calculated UV-B dose rates on clear-sky days in Lhasa show good agreement. Comparisons of UV-B radiation levels in Lhasa (Tibet), Oslo (Norway), and Dar-Es-Salaam (Tanzania) show that the UV-B dose rates during the summer in Lhasa are higher than the maximum value in Dar-Es-Salaam, which is at the sea level in the equatorial region, and 60% higher than in Oslo, which is at the sea level but 60 degrees North. We conclude that the UV-B dose rates during the summer on the Tibetan plateau are among the highest levels in habituated regions of the world. Maximum measured daily-integrated UV-B doses in Lhasa range from about 10 kJ/m² in the winter to about 65 kJ/m² in the summer.     

Comprehending adsorption of methylethylketone and toluene and microwave regeneration effectiveness for beaded activated carbon derived from recycled waste bamboo tar

ABSTRACT

Beaded activated carbons (BACs) were derived from waste bamboo tar through carbonization (500°C for 2 hr) followed by physical activation using carbon dioxide (800–900°C for 2–4 hr). The adsorbent was examined for their physical and chemical properties, adsorption capacities toward methylethylketone (MEK) and toluene, and regenerabilities under microwave heating. It was found that the maximum total surface area reached for bamboo-tar-derived BAC after physical activation was 1364 m² g^?1, and more than 95% of the area was attributed to the microporous structures. Langmuir, Freundlich, and Dubinin-Radushkevich (D-R) isotherm models were applied to the adsorption isotherm fitting, and the minimum R² for each model was 0.986, 0.915, and 0.943, respectively. The isosteric heats of adsorption calculated based on D-R parameters for methylethylketone and toluene were 44.04 to 51.50 and 45.88 to 73.27 KJ mol^?1, respectively. They were slightly over the range of physisorption and increased with adsorbate loading, which might be related to the micropore filling mechanism. Microwave regeneration under 600 W of power output removed most of the adsorbate (>93.03%) within 8 min. The results of this study are intended to benefit future study on waste-derived adsorbent in environmental applications.     

Introduction to the Air & Waste Management Association's 29th Annual Critical Review

Abstract

On-road mobile sources contribute substantially to ambient air concentrations of the carcinogens 1,3-butadiene, benzene, and polycyclic aromatic hydrocarbons (PAHs). The current study measured benzene and 1,3-butadiene at the Baltimore Harbor Tunnel tollbooth over 3-hr intervals on seven weekdays (n = 56). Particle-bound PAH was measured on a subset of three days. The 3-hr outdoor 1,3-butadiene levels varied according to time of day and traffic volume. The minimum occurred at night (12 a.m.–3 a.m.) with a mean of 2 µg/m³ (SD = 1.3, n = 7), while the maximum occurred during the morning rush hour (6 a.m.–9 a.m.) with a mean of 11.9 µg/m³ (SD = 4.6, n = 7). The corresponding traffic counts were 1413 (SD = 144) and 16,893 (SD = 692), respectively. During the same intervals, mean benzene concentration varied from 3 µg/m³ (SD = 3.1, n = 7) to 22.3 µg/m³ (SD = 7.6, n = 7). Median PAH concentrations ranged from 9 to 199 ng/m³. Using multivariate regression, a significant association (p < 0.001) between traffic and curbside concentration was observed. Much of the pollutant variability (1,3-butadiene 62%, benzene 77%, and PAH 85%) was explained by traffic volume, class, and meteorology. Results suggest >2-axle vehicles emit 60, 32, and 9 times more PAH, 1,3-butadiene, and benzene, respectively, than do 2-axle vehicles. This study provides a model for estimating curbside pollution levels associated with traffic that may be relevant to exposures in the urban environment.     

Effects of Equilibration Temperature on PM10 Concentrations from the TEOM Method in the Lower Fraser Valley

ABSTRACT

This study investigated the effect of equilibration temperature on PM₁₀ concentrations from the tapered element oscillating microbalance (TEOM) method by operating collocated TEOM monitors at different equilibration temperatures in an airshed (the Lower Fraser Valley, British Columbia). This airshed contained an abundance of par-ticulate semivolatile material (PSVM). For the period when three collocated TEOM monitors were operated, the PM₁₀ from the monitor at an equilibration temperature of 30 ° C was 2.5 μ g/m³ (22%) and 1.7 (17%) μ g/m³ higher, on average, than the PM₁₀ from monitors at 50 and 40 ° C, respectively, and the differences were proportional to the ambient PM₁₀ loading. Greater volatilization of PSVM in the TEOM monitors at higher equilibration temperatures may have been a cause of the differences.     

Performance Characteristics of a Regenerative Catalytic Oxidizer for Treating VOC-Contaminated Airstreams

ABSTRACT

A pilot apparatus of a regenerative catalytic oxidizer (RCO) equipped with two electrical heaters and two 20-cm i.d. × 200-cm height regenerative beds was used to treat methyl ethyl ketone (MEK) and toluene, respectively, in an airstream. The regenerative beds were packed with gravel (approximate particle size 1.25 cm, specific area 205 m²/m³, and specific heat capacity 840 J/kg °C) as a solid regenerative material and K-type thermal couples for measuring solid and gas temperatures, respectively. The catalyst bed temperature was kept around 400 °C and the gas superficial velocity was operated at 0.234 m/sec. This investigation measured and analyzed distributions of solid and gas temperatures with operating time and variations of volatile organic compound (VOC) concentrations in the regenerative beds. The overall VOC removal efficiency exceeded 98% for MEK and 95% for toluene. Degradation of VOCs will exist for MEK on the surface of solid material (gravel) in the temperature range of 330-400 °C, but toluene does not exhibit this phenomenon.     

Studies of the effects of temperatures and solar radiation on volatilization,mineralization and binding of 14c‐DDT in soil under laboratory conditions

Abstract

The effects of temperatures and solar radiation on the dissipation of ¹⁴C‐p,p'‐DDT from a loam soil was studied by quantifying volatilization, mineralization and binding. The major DDT loss occurred by volatilization, which was 1.8 times more at 45^oC than at ambient temperature (30°C). Mineralization of DDT slowly increased with time but it decreased slightly with increase in temperature. Binding of DDT to soil was found to be less at higher temperatures (35 and 45°C) as compared to ambient temperature. Degradation of DDT to DDE was faster at higher temperatures.

Exposure of non‐sterilized and sterilized soils treated with ¹⁴C‐DDT to sunlight in quartz and dark tubes for 6 weeks resulted in significant losses. Volatilization and mineralization in quartz tubes were more as compared to dark tubes. The volatilized organics from the quartz tubes contained larger amounts of p,p'‐DDE than the dark tubes. Further, higher rates of volatilization were found in non‐sterilized soils than in sterilized soils. The results suggest that faster dissipation of DDT from soil under local conditions relates predominantly to increased volatilization as influenced by high temperature and intense solar radiation.     

Density of foliage mass and area in the boreal forest cover in Finland,with applications to the estimation of monoterpene and isoprene emissions

The distribution of the density of foliage mass and area in forest canopies throughout Finland (60–70°N) were determined on the basis of the permanent sample plots used in the Finnish National Forest Inventory. These parameters were linked to the long-term monthly mean air temperatures for 1961–1990, which had been converted to hourly temperature and radiation values with the help of a weather simulator in order to calculate the spatial distribution of mean yearly emissions of monoterpene and isoprene over Finland. The mean total density of foliage mass in southern Finland (60°⩽latitude<65°N) was around 500 g m⁻², equivalent to 4–5 m² of total foliage area per m² of land area. In northern Finland (65°⩽latitude<70°N), the maximum values remained below 200–300 g m⁻², or 2–3 m² m⁻². The highest values were achieved in forests dominated by mature Norway spruces. The higher temperatures and longer growing season in southern Finland led to greater emissions than in the rest of the country. Total annual emissions of monoterpene were 1070 kg km⁻² yr⁻¹ in southern Finland and 460 kg km⁻² yr⁻¹ in the north, and those of isoprene from Norway spruce canopies 150 and 40 kg km⁻² yr⁻¹, respectively.     

Shift of microbial diversity and function in high-efficiency performance biotrickling filter for gaseous xylene treatment

ABSTRACT

Xylene is the main component of many volatile industrial pollution sources, and the use of biotechnology to remove volatile organic compounds (VOCs) has become a growing trend. In this study, a biotrickling filter for gaseous xylene treatment was developed using activated sludge as raw material to study the biodegradation process of xylene. Reaction conditions were optimized, and long-term operation was performed. The optimal pH was 7.0, gas-liquid ratio was 15:1 (v/v), and temperature was 25 °C. High-throughput sequencing technique was carried out to analyze microbial communities in the top, middle, and bottom layers of the reactor. Characteristics of microbial diversity were elucidated, and microbial functions were predicted. The result showed that the removal efficiency (RE) was stable at 86%–91%, the maximum elimination capacity (EC) was 303.61 g·m^?3·hr^?1, residence time was 33.75 sec, and the initial inlet xylene concentration was 3000 mg·m^?3, which was the highest known degradation concentration reported. Kinetic analysis of the xylene degradation indicated that it was a very high-efficiency-activity bioprocess. The r_max was 1059.8 g·m^?3·hr^?1, and K_s value was 4.78 g·m^?3 in stationary phase. In addition, microbial community structures in the bottom and top layers were significantly different: Pseudomonas was the dominant genus in the bottom layer, whereas Sphingobium was dominant in the top layer. The results showed that intermediate metabolites of xylene could affect the distribution of community structure. Pseudomonas sp. can adapt to high concentration xylene–contaminated environments.

Implications: We combined domesticated active sludge and reinforced microbial agent on biotrickling filter. This system performed continuously under a reduced residence time at 33.75 sec and high elimination capacity at 303.61 g·m^?3·hr^?1 in the biotrickling reactor for about 260 days. In this case, predomestication combined with reinforcing of microorganisms was very important to obtaining high-efficiency results. Analysis of microbial diversity and functional prediction indicated a gradient distribution along with the concentration of xylene. This implied a rational design of microbial reagent and optimizing the inoculation of different sites of reactor could reduce the preparation period of the technology.     

Ultraviolet radiation spatio-temporal characteristics derived from the ground-based measurements taken in China

Ultraviolet (UV) radiation and broadband solar radiation (R_s) measured from January 2005 to June 2006 at 31 stations in Chinese Ecosystem Research Network (CERN) were used to investigate the spatio-temporal characteristics of UV radiation and UV fraction (the ratio of UV radiation to R_s) in China. Results indicated that the seasonal variations of UV radiation and R_s were consistent with the solar activities, which reached their lower values during winter period, and increased throughout the spring, peaking in June or July, in most sites. The Meiyu weather system and Southwest Monsoon produced different variation characteristics of UV radiation and R_s in subtropical and tropical regions. The UV fraction values showed a similar seasonal trend as that of UV radiation, which was mainly determined by the seasonal change of the aerosol optical depth (AOD) and water vapor content in atmosphere. The seasonal variations of UV fraction were much smoother in southern China due to high water vapor content over the whole year.The UV radiation showed an increasing trend from east to west in China. In the western area, a simple increasing trend was observed from north to south, with the largest annual mean daily UV value 0.91 MJ m⁻² appearing in the Qinghai-Tibet Plateau area. In east China there was a low center that appeared in the subtropical region due to high aerosol burden, with the lowest value 0.41 MJ m⁻² observed in Yanting site. Two high centers were located in the tropics with higher solar altitudes and the north desert region with low atmospheric attenuation. The largest values of UV fraction appeared in the tropical and subtropical regions due to higher relative humidity (RH) in these areas. However, the smallest value did not appear in the north desert region where the RH was the lowest, they were found at the Luancheng site which featured relatively low humidity and abundant fine aerosols. The variations in the UV fraction were not such distinctive as those of the UV radiation in China due to the more complex influences of aerosol and water vapor.     

Mycobiota and mycotoxins in bee pollen collected from different areas of Slovakia

Contamination by microscopic fungi and mycotoxins in different bee pollen samples, which were stored under three different ways of storing as freezing, drying and UV radiation, was investigated. During spring 2009, 45 samples of bee-collected pollen were gathered from beekeepers who placed their bee colonies on monocultures of sunflower, rape and poppy fields within their flying distance. Bee pollen was collected from bees’ legs by special devices placed at the entrance to hives. Samples were examined for the concentration and identification of microscopic fungi able to grow on Malt and Czapek-Dox agar and mycotoxins content [deoxynivalenol (DON), T-2 toxin (T-2), zearalenone (ZON) and total aflatoxins (AFL), fumonisins (FUM), ochratoxins (OTA)] by direct competitive enzyme-linked immunosorbent assays (ELISA). The total number of microscopic fungi in this study ranged from 2.98 ± 0.02 in frozen sunflower bee pollen to 4.06 ± 0.10 log cfu.g^?1 in sunflower bee pollen after UV radiation. In this study, 449 isolates belonging to 21 fungal species representing 9 genera were found in 45 samples of bee pollen. The total isolates were detected in frozen poppy pollen 29, rape pollen 40, sunflower pollen 80, in dried poppy pollen 12, rape pollen 36, sunflower 78, in poppy pollen after UV radiation treatment 54, rape 59 and sunflower 58. The most frequent isolates of microscopic fungi found in bee pollen samples of all prevalent species were Mucor mucedo (49 isolates), Alternaria alternata (40 isolates), Mucor hiemalis (40 isolates), Aspergillus fumigatus (33 isolates) and Cladosporium cladosporioides (31 isolates). The most frequently found isolates were detected in sunflower bee pollen frozen (80 isolates) and the lowest number of isolates was observed in poppy bee pollen dried (12 isolates). The most prevalent mycotoxin of poppy bee pollen was ZON (361.55 ± 0.26 μg.kg^?1), in rape bee pollen T-2 toxin (265.40 ± 0.18 μg.kg^?1) and in sunflower bee pollen T-2 toxin (364.72 ± 0.13 μg.kg^?1) in all cases in frozen samples.     

Adsorption and desorption variability of four herbicides used in paddy rice production

This investigation was performed to determine the effect of physicochemical soil properties on penoxsulam, molinate, bentazon, and MCPA adsorption–desorption processes. Four soils from Melozal (35° 43′ S; 71° 41′ W), Parral (36° 08′ S; 71° 52′ W), San Carlos (36° 24′ S; 71° 57′ W), and Panimavida (35° 44′ S; 71° 24′ W) were utilized. Herbicide adsorption reached equilibrium after 4 h in all soils. The Freundlich L-type isotherm described the adsorption process, which showed a high affinity between herbicides and sorption sites mainly because of hydrophobic and H-bonds interaction. Penoxsulam showed the highest adsorption coefficients (4.23 ± 0.72 to 10.69 ± 1.58 mL g^?1) and were related to soil pH. Molinate showed K_d values between 1.72 ± 0.01 and 2.3 ± 0.01 mL g^?1and were related to soil pH and organic matter, specifically to the amount of humic substances. Bentazon had a high relationship with pH and humic substances and its K_d values were the lowest, ranging from 0.11 ± 0.01 to 0.42 ± 0.01 mL g^?1. MCPA K_d ranged from 0.14 ± 0.02 to 2.72 ± 0.01 mL g^?1, however its adsorption was related to humic acids and clay content. According to these results, the soil factors that could explain the sorption process of the studied herbicides under paddy rice soil conditions, were principally humic substances and soil pH. Considering the sorption variability observed in this study and the potential risk for groundwater contamination, it is necessary to develop weed rice management strategies that limit use of herbicides that exhibit low soil adsorption in areas with predisposing conditions to soil leaching.     

Degradation of polycyclic aromatic hydrocarbons in a coking wastewater treatment plant residual by an O3/ultraviolet fluidized bed reactor

Coking wastewater treatment plant (CWWTP) represents a typical point source of polycyclic aromatic hydrocarbons (PAHs) to the water environment and threatens the safety of drinking water in downstream regions. To enhance the removal of residual PAHs from bio-treated coking wastewater, a pilot-scale O₃/ultraviolet (UV) fluidized bed reactor (O₃/UV FBR) was designed and different operating factors including UV irradiation intensity, pH, initial concentration, contact time, and hydraulic retention time (HRT) were investigated at an ozone level of 240 g h^?1 and 25?±?3 °C. A health risk evaluation and cost analysis were also carried out under the continuous-flow mode. As far as we know, this is the first time an O₃/UV FBR has been explored for PAHs treatment. The results indicated that between 41 and 75 % of 18 target PAHs were removed in O₃/UV FBR due to synergistic effects of UV irradiation. Both increased reaction time and increased pH were beneficial for the removal of PAHs. The degradation of the target PAHs within 8 h can be well fitted by the pseudo-first-order kinetics (R ²?>?0.920). The reaction rate was also positively correlated with the initial concentrations of PAHs. The health risk assessment showed that the total amount of carcinogenic substance exposure to surface water was reduced by 0.432 g day^?1. The economic analysis showed that the O₃/UV FBR was able to remove 18 target PAHs at a cost of US$0.34 m^?3. These results suggest that O₃/UV FBR is efficient in removing residuals from CWWTP, thus reducing the accumulation of persistent pollutant released to surface water.