Metal partitioning in products of incineration of municipal solid waste

Metals contained in the waste transfer to the waste incineration products, including flue gas, fly ash, and bottom ash, as different oxide, nitride, carbides, and other phases. Most of the metal-based phases formed in incineration are toxic and their emissions need to be strictly controlled. Therefore, behavior of metal species during incineration must be well understood. Such understanding is possible based on the experimental identification of the metal phases formed in the waste combustion and determination of their concentration in various incineration products. To avoid well-known experimental difficulties of the industrial waste incinerators associated with the poor fuel/conditions reproducibility and limited instrumentation, a 140,000 Btu/h pilot-scale, laboratory burner was constructed, characterized and operated at NJIT. A synthetic fuel representative of the municipal solid waste in the US was formulated and produced in 600-Lb batches. The solid fuel contained Fe and SiO2 as main constituents, and was doped with trace amounts of Al, Ni, Cr, Hg and PbO. Several experiments have been conducted on combustion of the synthetic fuel in the pilot-scale incinerator with varying fuel-air equivalence ratio. Both gaseous and condensed combustion products were sampled and analyzed. Atomic absorption spectroscopy and X-ray diffraction were used to analyze total metal contents and metal containing phases in the incineration products. Thermodynamic equilibrium computations were performed to obtain the adiabatic flame temperature and identify the phases of the metal-containing products formed at the equilibrium conditions. The results of the equilibrium computations performed at the varied fuel/air ratios were compared with the observed experimental results.     

回转窑式纯氧熔融焚烧垃圾技术研究

生活垃圾安全无害化处理是目前迫切需要解决的问题,直接气化熔融焚烧垃圾技术以降低二恶英排放方面巨大优势得到广泛关注,在此基础上提出纯氧熔融焚烧垃圾技术,几乎可以实现所有二次污染物近零排放。以350 t/d回转窑垃圾焚烧炉为例,对纯氧代替空气应用在回转窑上熔融焚烧垃圾系统进行了详细热力计算及分析。结果表明,纯氧熔融焚烧垃圾系统的锅炉效率可达90.56%,回转窑熔融焚烧系统还可以在垃圾焚烧后灰渣达到熔融温度的条件下,保持该系统热量平衡,稳定燃烧。并参考回转窑设计标准对该纯氧熔融焚烧城市生活垃圾的回转窑参数进行确定。     

城市生活垃圾在机械炉排炉内焚烧过程研究及数值模拟

研究城市生活垃圾在机械炉排炉内焚烧过程，建立了垃圾在炉排炉移动床内燃烧过程中垃圾体积变化、水分蒸发、挥发分析出及燃烧、垃圾颗粒的移动、气-固两相热传递、焦炭燃烧等各个反应阶段的热化学模型，采用一维非稳态模型分别建立了床层内气固两相介质控制方程。通过对炉排上垃圾焚烧过程的数值模拟研究，获得料层中温度分布、料层高度、炉床机械负荷、气相中反应物组分和污染物浓度分布。利用建立的模型对某大型垃圾焚烧炉的燃烧过程进行数值仿真，对燃烧过程、烟气成分进行预测，为垃圾焚烧炉排炉的设计和燃烧控制提供理论依据。     

新型转式垃圾焚烧炉焚烧技术研究

研究了新型转式焚烧炉稳定燃烧工艺和有机垃圾在新型转式焚烧炉中焚烧过程HCl和NOx释放和控制特性。结果表明,新型转式焚烧炉采用二次燃烧技术,能有效控制和降低二次污染物的生成。     

150t/d循环流化床生活垃圾焚烧炉的工艺结构与污染排放

垃圾焚烧处理技术在我国的应用越来越广泛 ,单纯引进国外的垃圾焚烧处理技术已经无法满足我国经济发展的需要。清华大学自主开发研制的 15 0t/d循环流化床生活垃圾焚烧炉已经通过专家鉴定 ,各项焚烧污染物排放指标均达到或优于国家标准 ,总体水平居国内领先水平。本文详细介绍了该焚烧炉的系统及结构 ,并对有关控制污染物排放的技术手段进行了详细分析     

Dioxins and their fingerprint in size-classified fly ash fractions from municipal solid waste incinerators in China—Mechanical grate and fluidized bed units

The distribution of polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDD/Fs), in brief dioxins, has seldom been addressed systematically in fly ash from municipal solid waste incinerators (MSWIs). This study shows the amount and fingerprint of PCDD/Fs in fly ash from four different Chinese MSWIs, that is, three mechanical grate units and one circulating fluidized bed unit. In these fly ash samples, dioxins-related parameters (international toxic equivalent quantity, total amount of PCDD/Fs, individual isomer classes, and 17 toxic 2,3,7,8-substituted congeners) all tend to increase with decreasing particle size for mechanical grate incinerators, yet only for the finest fraction for fluidized bed units. Moreover, the fluidized bed incinerator seems superior to grate incineration in controlling dioxins, yet a comparison is hampered by internal differences in the sample, for example, the fluidized bed fly ash has much lower carbon and chlorine contents. In addition, the presence of sulfur from mixing coal as supplemental fuel to the MSW may poison the catalytic steps in dioxins formation and thus suppress the formation of dioxins. With more residual carbon and chlorine in the fly ash, it is easier to form dioxins during cooling. Nevertheless, there is no apparent relation between Fe, Cu, and Zn contents and that of dioxins in fly ash.

Implications This paper is of interest because it presents the amounts and distribution of PCDD/Fs in fly ash samples from some typical waste incineration plants in China, featuring distinct incinerator types, combustion conditions, fuel composition, or residual carbon, chloride, and heavy metal contents in fly ash.     

Control of mercury emissions from a municipal solid waste incinerator in Japan

The control of Hg emissions from a municipal solid waste incinerator (MSWI) is very important, because more than 78% of municipal solid waste (MSW) is incinerated. The Hg content of coal used in utility boilers is relatively low in Japan. In this study, recent trends in the Hg content of MSW in Japan and activated carbon (AC) injection as a control technology of Hg emission from an MSWI are discussed. The effect of AC injection on Hg removal from flue gas in an MSWI was investigated by pilot-scale experiments using a bag filter (BF). The injection of AC increases the Hg reduction ratio by 20-30% compared with cases without AC injection. The Hg reduction ratio increases as the flue gas temperature decreases. The Hg reduction ratio is closely related to the inlet Hg concentration and was expressed with a Langmuir-type adsorption isotherm.     

The study on biomass fraction estimate methodology of municipal solid waste incinerator in Korea

In Korea, the amount of greenhouse gases released due to waste materials was 14,800,000 t CO₂eq in 2012, which increased from 5,000,000 t CO₂eq in 2010. This included the amount released due to incineration, which has gradually increased since 2010. Incineration was found to be the biggest contributor to greenhouse gases, with 7,400,000 t CO₂eq released in 2012. Therefore, with regards to the trading of greenhouse gases emissions initiated in 2015 and the writing of the national inventory report, it is important to increase the reliability of the measurements related to the incineration of waste materials.

This research explored methods for estimating the biomass fraction at Korean MSW incinerator facilities and compared the biomass fractions obtained with the different biomass fraction estimation methods. The biomass fraction was estimated by the method using default values of fossil carbon fraction suggested by IPCC, the method using the solid waste composition, and the method using incinerator flue gas.

The highest biomass fractions in Korean municipal solid waste incinerator facilities were estimated by the IPCC Default method, followed by the MSW analysis method and the Flue gas analysis method. Therefore, the difference in the biomass fraction estimate was the greatest between the IPCC Default and the Flue gas analysis methods. The difference between the MSW analysis and the flue gas analysis methods was smaller than the difference with IPCC Default method. This suggested that the use of the IPCC default method cannot reflect the characteristics of Korean waste incinerator facilities and Korean MSW.

Implications: Incineration is one of most effective methods for disposal of municipal solid waste (MSW). This paper investigates the applicability of using biomass content to estimate the amount of CO₂ released, and compares the biomass contents determined by different methods in order to establish a method for estimating biomass in the MSW incinerator facilities of Korea. After analyzing the biomass contents of the collected solid waste samples and the flue gas samples, the results were compared with the Intergovernmental Panel on Climate Change (IPCC) method, and it seems that to calculate the biomass fraction it is better to use the flue gas analysis method than the IPCC method. It is valuable to design and operate a real new incineration power plant, especially for the estimation of greenhouse gas emissions.     

垃圾焚烧炉干燥段通风阻力特性实验研究

倾斜往复式炉排是我国城市生活垃圾焚烧炉中经常采用的炉排形式之一。垃圾在炉排干燥段的干燥效果直接影响到其着火和燃烧,因此炉排下侧送出的一次风在垃圾层中的流通性显得尤其重要。本研究通过搭建冷态试验台,以Steinmuller炉排为例,测量了炉排和不同厚度的垃圾层在不同一次风流量下的阻力,并研究了炉排和垃圾层的通风阻力特性,为今后更好地组织和控制高水份垃圾在炉内的干燥预热和着火燃烧提供了设计依据。     

北京市朝阳区城市生活垃圾组分分布特性研究

针对垃圾焚烧的需要，按垃圾组分低位热值重新进行了垃圾分类，检验了各组分的正态分布特性，得出了服从正态分布的垃圾组分的概率分布密度函数。进行了垃圾含水率的线性相关性分析，认为垃圾含水率与厨余的相关性最大，降水量对含水率影响不大。     

城市生活垃圾焚烧过程中二次污染物的生成与控制

在我国 ,采用焚烧法处理城市固体垃圾 ,逐渐得到推广和应用。然而焚烧带来的二次污染物 ,如二、细颗粒、重金属、HCl以及SOx、NOx 等也随之引起了广泛关注。对垃圾焚烧过程中各种二次污染物的产生机理及其控制方法进行了综述。并且指出近期我国城市固体垃圾焚烧烟气污染物的重点控制对象应为颗粒物、HCl、SOx 和NOx。     

Prediction for energy content of Taiwan municipal solid waste using multilayer perceptron neural networks

In the past decade, the treatment amount of municipal solid waste (MSW) by incineration has increased significantly in Taiwan. By year 2008, approximately 70% of the total MSW generated will be incinerated. The energy content (usually expressed by lower heating value [LHV]) of MSW is an important parameter for the selection of incinerator capacity. In this work, wastes from 55 sampling sites, including villages, towns, cities, and remote islands in the Taiwan area, were sampled and analyzed once a season from April 2002 to March 2003 to determine the waste characteristics. The LHV of MSW in Taiwan was predicted by the multilayer perceptron (MLP) neural networks model using the input parameters of elemental analysis and dry- or wet-base physical compositions. Although all three of the models predicted LHV values rather accurately, the elemental analysis model provided the most accurate prediction of LHV values. Additionally, the wet-base physical composition model was the easiest and most economical. Therefore, the waste treatment operators can choose the more appropriate analysis method considering situations themselves, such as time, equipment, technology, and cost.     

A life-cycle inventory model of municipal solid waste combustion

Evaluation of alternate strategies for municipal solid waste (MSW) management requires models to calculate environmental emissions as a function of both waste quantity and composition. A methodology to calculate waste component-specific emissions associated with MSW combustion is presented here. The methodology considers emissions at a combustion facility as well as those avoided at an electrical energy facility because of energy recovered from waste combustion. Emission factors, in units of kg pollutant per metric ton MSW entering the combustion facility, are calculated for CO2-biomass, CO2-fossil, SOx, HCl, NOx, dioxins/furans, PM, CO, and 11 metals. Water emissions associated with electrical energy offsets are also considered. Reductions in environmental emissions for a 500-metric-ton-per-day combustion facility that recovers energy are calculated.     

城市生活垃圾卫生填埋场恶臭的防治技术进展

恶臭污染已成为垃圾处理和处置过程中的严重公害。在分析中,介绍了填埋场各区域恶臭的控制措施,综述了卫生填埋场恶臭的常规防治技术,重点讨论了生物技术在填埋场脱臭中的应用,这些防治技术对各类环境卫生设施,如垃圾收集站、中转站、焚烧场、堆肥厂及粪便处理厂的臭气治理均有借鉴意义。     

Control of Mercury Emissions from a Municipal Solid Waste Incinerator in Japan

Abstract

The control of Hg emissions from a municipal solid waste incinerator (MSWI) is very important, because more than 78% of municipal solid waste (MSW) is incinerated. The Hg content of coal used in utility boilers is relatively low in Japan. In this study, recent trends in the Hg content of MSW in Japan and activated carbon (AC) injection as a control technology of Hg emission from an MSWI are discussed. The effect of AC injection on Hg removal from flue gas in an MSWI was investigated by pilot-scale experiments using a bag filter (BF). The injection of AC increases the Hg reduction ratio by 20–30% compared with cases without AC injection. The Hg reduction ratio increases as the flue gas temperature decreases. The Hg reduction ratio is closely related to the inlet Hg concentration and was expressed with a Langmuir-type adsorption isotherm.     

Urea as a PCDD/F inhibitor in municipal waste incineration

Emissions of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) from municipal waste incineration have been widely studied because of their extensive toxicity, and many efforts have been made to restrict their emissions. Although a number of chemical compounds have been shown in laboratory-scale tests to inhibit the formation of PCDD/Fs, few have been tested in pilot- or full-scale plants. This work evaluates the effect of urea as a PCDD/F inhibitor in a pilot-scale incinerator that uses refuse-derived fuel (RDF). The decomposition of urea under the test conditions was also studied using detailed kinetic modeling. An aqueous solution of urea was injected into the flue gas stream after the furnace at approximately 730 degrees C, with varied urea concentrations and flue gas residence times used between the furnace and the sampling point. The results demonstrate that urea can successfully inhibit PCDD/F formation in waste incineration if concentrations and injection points are properly adjusted. The kinetic model showed that urea can be rapidly decomposed under appropriate flue gas conditions, indicating that in addition to the urea molecule itself, decomposition products of urea can also be responsible for the reduction of PCDD/F production during incineration.     

Dioxins and their fingerprint in size-classified fly ash fractions from municipal solid waste incinerators in China--mechanical grate and fluidized bed units

The distribution of polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDD/Fs), in brief dioxins, has seldom been addressed systematically in fly ash from municipal solid waste incinerators (MSWIs). This study shows the amount and fingerprint of PCDD/Fs in fly ash from four different Chinese MSWIs, that is, three mechanical grate units and one circulating fluidized bed unit. In these fly ash samples, dioxins-related parameters (international toxic equivalent quantity, total amount of PCDD/Fs, individual isomer classes, and 17 toxic 2,3,7,8-substituted congeners) all tend to increase with decreasing particle size for mechanical grate incinerators, yet only for the finest fraction for fluidized bed units. Moreover, the fluidized bed incinerator seems superior to grate incineration in controlling dioxins, yet a comparison is hampered by internal differences in the sample, for example, the fluidized bed fly ash has much lower carbon and chlorine contents. In addition, the presence of sulfur from mixing coal as supplemental fuel to the MSW may poison the catalytic steps in dioxins formation and thus suppress the formation of dioxins. With more residual carbon and chlorine in the fly ash, it is easier to form dioxins during cooling. Nevertheless, there is no apparent relation between Fe, Cu, and Zn contents and that of dioxins in fly ash.     

Dioxin emissions from waste incinerators

Mechanisms that have been proposed to account for the emission of PCDD/PCDF from municipal waste incinerators were evaluated in the light of extensive experimental data obtained from the Quebec City municipal solid waste incinerator by Environment Canada. It was found that PCDD/PCDF emissions were closely related to the quantity of material entrained by the combustion gases.     

采用循环流化床技术焚烧城市生活垃圾

根据目前我国城市生活垃圾热值偏低的实际情况 ,提出以煤为辅助燃料 ,采用循环流化床焚烧技术处理生活垃圾 ,可大幅度降低运行成本 ,符合国情。阐述了循环流化床焚烧技术在降低NOx、SO2 和二噁等方面的优越性。尾气处理建议采用喷活性碳 +布袋除尘组合工艺 ,飞灰处理建议采用高温熔融处理     

Systematic Evaluation and Uncertainty Analysis of the Refuse-Derived Fuel Process in Taiwan

ABSTRACT

In the last few years, Taiwan has set a bold agenda in solid waste recycling and incineration programs. Not only were the recycling activities and incineration projects promoted by government agencies, but the related laws and regulations were continuously promulgated by the Legislative Yen. The solid waste presorting process that is to be considered prior to the existing incineration facilities has received wide attention. This paper illustrates a thorough evaluation for the first refuse-derived fuel pilot process from both quantitative and qualitative aspects. The process is to be installed and integrated with a large-scale municipal incinerator. This pilot process, developed by an engineering firm in Tainan County, consists of standard unit operations of shredding, magnetic separation, trommel screening, and air classification. A series of sampling and analyses were initialized in order to characterize its potentials in the solid waste management system. The probabilistic modeling for various types o f waste pro perties derived in this analysis may provide a basic understanding of system reliability.