等离子体协同光催化去除模拟烟气中SO2的实验研究

近年来,低温等离子体技术以及纳米TiO2光催化技术在烟气脱硫中的应用越来越引起人们的关注.利用填充床反应器将这2种技术有机地结合起来,进行了大量脱硫实验研究.研究结果表明,等离子体协同光催化去除烟气中的SO2与单独采用等离子体技术相比,其SO2的去除率可提高5%～20%.同时,探讨了等离子体协同TiO2光催化剂的脱硫机理,分别研究了外加电压、气体流量和SO2初始浓度等因素对脱硫效率的影响.实验结果表明,当SO2初始浓度为800mg/m3,输入电压为17.5 kV,气体流量为0.2 m3/h时,SO2脱除率可以达到77.6%.     

改进型生物滴滤塔处理H2S臭气的最适工艺条件研究

以H2S气体为研究对象,考察改进型生物滴滤塔的脱臭效能、最适工艺运行条件及其影响因素.试验结果表明,循环液喷淋量为10 L/s,气体流量为400 L/s的情况下,最高H2S负荷率可以达到68.2 g/m3·h;最适气体停留时间68.4 s.当入口H2S浓度分别为0～700 mg/m3、700～1000 mg/m3和大于1000 mg/m3时,对应的最适循环液喷淋量为10 L/s、15 L/s和60 L/s.H2S去除率100%的情况下,最大允许进气浓度可达1870 mg/m3,即最大H2S负荷率为98.4 g/m3·h.该研究表明,改进型生物滴滤塔具有较高的H2S去除能力,最适工艺运行条件的确定对污水厂臭气和化工行业产生的H2S处理具有一定的指导意义.     

生物催化氧化法脱除H2S的试验研究

针对H2S污染的严峻形势,构建了包括催化再生装置和生物滴滤器的生物催化氧化装置.该装置以沸石为填料,以氧化亚铁硫杆菌为脱硫菌种,通过微生物和Fe3 的双重氧化作用高效脱除H2S.试验确定了装置的适宜喷淋量和沸石的最佳粒径.在温度为30 ℃,进气量为0.25 m3/h,进气H2S浓度为2500 mg/m3,喷淋量为1000 mL/h,喷淋液的pH值为1.97、Fe3 浓度为0.05 mol/L的条件下,出气H2S浓度足以达到GB14554-93规定的一级厂界标准值.试验证明,生物催化氧化法是一种新型高效的脱硫技术,应进一步开展中试研究.     

接种物对厌氧同步脱硫反硝化特性的影响实验研究

分别以厌氧污泥、脱氮硫杆菌菌悬液和厌氧污泥并添加脱氮硫杆菌菌悬液为接种物,以硫化物和硝酸盐为进水基质,考察不同接种物条件下,各反应器的硫化物氧化特性、反硝化特性、生化反应机理及微生物特性。结果表明,在无菌条件下,硫化物不能被硝酸盐化学氧化。接种脱氮硫杆菌菌悬液的2#反应器的硫氧化速率为1.98 g S/(m3.h),停留24 h硫化物的去除率高达97%,脱硫能力最强,该接种条件下以硝酸盐氧化硫化物为主反应,优势菌为杆菌,进水的NO3--N/S应控制在0.4以下,可以实现高效生物脱硫。接种厌氧污泥的1#和3#反应器的脱氮效果比2#反应器好,停留时间为24 h时,硝酸盐的平均去除率为96%。单独接种厌氧污泥的1#反应器的硫氧化速率为1.78 g S/(m3.h),其优势菌为球菌,该接种条件下以硝酸盐氧化硫化物和硝酸盐氧化单质硫为主反应,进水的NO3--N/S应控制在0.8左右。以厌氧污泥联合脱氮硫杆菌为接种物时,硫氧化速率为1.71 g S/(m3.h),反应器以硝酸盐氧化硫化物、硝酸盐氧化单质硫以及异养反硝化为主反应,驯化后优势菌为球形、卵圆形和短杆状,应控制进水NO3--N/S为1.2,可以实现同步脱硫反硝化,该工艺既可以用于含硫废水的处理,也可以用于C/N低的硝酸盐废水的处理。     

酸性洗涤塔-生物滤塔-生物曝气池组合工艺处理恶臭气体NH3和H2S

采用酸性洗涤塔、生物滤塔和生物曝气池的组合工艺处理NH3、H2S恶臭混合气体,研究表明,该组合工艺对NH3和H2S有很好的去除效果,在进气流量为35 L/min,喷淋量45 L/h时,NH3进气浓度50.15~525.4 mg/m3,H2S进气浓度10.23~110.36 mg/m3时,NH3单一进气去除率稳定在99%以上,H2S单一进气去除率90%以上。混合进气后,NH3去除率几乎为100%,H2S的去除率提高至98%以上。在一定的浓度范围内,NH3和H2S之间的相互作用对两者的去除效果没有明显的影响,而且起到了相互促进降解的作用。同时,进气流量和填料层高度都会影响NH3、H2S的去除率。系统对进气容积负荷变化的缓冲能力强,在偶尔超负荷条件下运行并不能使系统崩溃,并且微生物对高负荷逐渐表现出适应性。大部分溶于水的氨由生物曝气池去除,去除率达到96.9%。     

生物滴滤塔处理H_2S臭气

目前,环保政策极其关注污水处理厂的臭气排放并制定了排放标准。本实验依托3个并联的中试生物滴滤塔对污水提升泵站的H2S臭气展开研究,考察不同H2S进气负荷、停留时间、压降和填料填装方式(竹炭-陶粒分层填装、完全混合及全竹炭填装)等因素对H2S去除率的影响。对生物滴滤塔的出气浓度、滤出液p H、SO2-4离子等进行测试分析,建立传质、降解动力学模型,并分析。在停留时间为25 s连续进气条件下,考察进气负荷在0.59~5.00 g H2S/(m3·h)范围内生物滴滤塔对H2S臭气的去除表现效果。研究结果表明,各生物滴滤塔的去除率(RE)都维持在98%以上,而且出气浓度达到厂界废气排放三级标准;相较于完全混合填装方式,分层填装在去除H2S臭气时略显优势。采用Michaelis-Menten方程描述生物滴滤塔的去除表现,表观半饱和常数Ks和最大表观去除速率Vm分别为5.92 m L/m3和5.84 g H2S/(m3·h)。     

高气速间歇式生物过滤去除高负荷H2S

采用生物过滤法,以鸡粪堆肥和PE混合物为填料,在高气速条件下间歇式处理高负荷H2S废气。空床停留时间为20、15、10、6.7和5 s时,入口浓度3 000 mg/m3下的平均去除率分别为100%、100%、96.5%、89.2%和90.5%。高气速EBRT为5 s时,高入口负荷2 147 g/(m3.h)时的去除负荷为2 023 g/(m3.h),去除率达94%。采用Michaelis-Ment-en模型进行生物降解宏观动力学研究,其中Ks为550 mg/m3,Vm为6.8×104g/(m3.d)。结果表明,在实验温度17～24℃,湿度30%～50%下,生物过滤法间歇式处理高气速高负荷H2S的去除性能好。     

氢氧化钠-钢渣双碱法烧结烟气脱硫工艺

在鼓泡反应器中考察了氢氧化钠-钢渣双碱法烧结烟气脱硫的主要影响因素。结果表明,在温度为常温,钢渣反应时间为2 h,钢渣加入量为40 g,SO2进口浓度为2 400 mg/m3,钢渣粒径为200目以上,烟气流量为0.05 m3/h,循环液pH保持在7～8,Na+浓度为0.5 mol/L,循环液为500 mL的条件下,脱硫率可长时间保持在80%以上。同时,对钢渣-氢氧化钠双碱法烧结烟气脱硫机理进行了探讨。     

生物催化氧化法脱除H2S的填料选择研究

针对H2S污染的严峻形势,构建了包括催化再生装置和生物滴滤器的生物催化氧化装置,进行了装置的填料选择研究.经对比试验得出填料脱硫性能的优劣顺序为:沸石＞焦炭＞多面空心塑料小球.在温度为30 ℃、进气量为0.25 m3/h、进气H2S为2 000 mg/m3、喷淋量为1 000 mL/h、喷淋液的pH为1.97、Fe3 为0.05 mol/L的条件下,装填沸石的生物催化氧化装置的出气H2S浓度足以达到<恶臭污染物排放标准>(GB 14554-93)规定的一级厂界标准值.试验证明,生物催化氧化法是有效的新型脱除H2S技术,具有良好的经济、社会及环境效益,应进一步开展中试研究.     

铁氧化物多孔陶粒生物滴滤塔净化硫化氢气体

采用装有凹凸棒石基铁氧化物多孔陶粒作为填料的生物滴滤塔,进行了长期实验室H2S脱臭实验。结果表明,该生物滴滤塔H2S的进气浓度低于500 mg/m3时,循环营养液喷淋量高于1.5 L/h,气体最佳停留时间为54.9 s,去除率在95%以上。代谢产物以SO2-4为主,转化速率在52.42 g/(m3·d)左右。该滴滤塔系统可稳定而有效运行。生物相观察表明,滴滤塔填料表面附着大量微生物,铁氧化物陶粒具有化学和生物惰性,有利于微生物的附着。     

Bio-SR工艺去除硫化氢气体的研究

采用Bio-SR工艺,利用铁盐吸收与氧化亚铁硫杆菌的联合作用对H2S进行脱除实验。通过改进微生物的培养条件,减少了83.9%的沉淀量,一定程度上解决了挂膜后生物填料塔易堵塞的问题,保证了填料塔的连续运行。在实验选取工况下,硫化氢脱除率可达到98.4%以上,当吸收液中Fe3+浓度为5.5～6 g/L、H2S进气浓度为1 g/m3、通气量为0.08～0.12 m3/h时效果最佳,反应器可持续高效地运行。此外,对进气浓度、通气量与硫化氢去除率之间的相关性进行了进一步研究,其结果有利于反应器及运行参数的优化设计。     

一株脱硫菌的分离及脱硫动力学

从污水处理厂二沉池分离获得一株硫酸盐还原菌厌氧菌株,依据生理生化分析和16S rDNA基因序列测定该菌株被鉴定为脱硫脱硫弧菌(Desulfovibrio desulfuricans)。在气体吸收的双膜理论和液相中微生物转化的米门方程基础上,建立了搅拌式生物吸收反应器中脱硫脱硫弧菌净化二氧化硫气体的动力学模型,并求解出相应的动力学参数基质转化最大速度Vmax和米氏常数Km,实验结果所得到的线性方程相关性较好,线性相关系数可以达到0.998,而且脱硫脱硫弧菌吸收液具有较高转化二氧化硫的能力。     

鼓泡反应器中液相络合催化同时脱硫脱硝的研究

在鼓泡反应器中考察了[Co(en)3]2+同时吸收去除SO2和NO的影响因素,实验结果表明,pH值和脱硫剂种类是影响乙二胺合钴同时脱除NO和SO2的最重要影响因素,烟气中的氧促进乙二胺合钴吸收NO和SO2,烟气中的SO2,CO2和NO2对乙二胺合钴吸收NO具有抑制作用。在实验条件温度为20℃,pH为13.0,[Co(en)3]2+浓度为0.025 mol/L,加入1 g NH3.H2O的脱硝率更好,连续吸收60 min,脱硝率均保持在93.5%,加入NaOH和NH3.H2O的脱硫效果最好。乙二胺合钴络合同时脱除NO和SO2完全可以在一个装置中完成。     

Contributions of fermentative acidogenic bacteria and sulfate-reducing bacteria to lactate degradation and sulfate reduction

The roles of fermentative acidogenic bacteria and sulfate-reducing bacteria (SRB) in lactate degradation and sulfate reduction in a sulfidogenic bioreactor were investigated by traditional chemical monitoring and culture-independent methods. A continuously stirred tank reactor fed with synthetic wastewater containing lactate and SO(2-)(4) at 35 degrees C, 10h of hydraulic retention time was used. The results showed that sulfate removal efficiency reached 99%, and sulfide and acetate were the main end products after 20 d of operation. 16S rRNA gene based clone libraries and single-strand conformation polymorphism profiles demonstrated that the proportion of SRB increased from 16% to 95%, and that Desulfobulbus spp., Desulfovibrio spp., Pseudomonas spp. and Clostridium spp. formed a stable, dominant community structure. The decreasing COD/SO(2-)(4) ratio had little effect on the community pattern except that Pseudomonas spp. and Desulfobulbus spp. increased slightly. The addition of molybdate to the influent significantly changed the microbial community, sulfate removal efficiency and the pattern of end products. Clostridium spp., Bacteroides spp. and Ruminococcus spp. became the dominant community members. The main end products switched from acetate to ethanol and then to propionate with the oxidation-reduction potentials increasing from -420 to -290 mV. A lactate degradation pathway was deduced: lactate served as the electronic donor for Desulfovibrio spp., or was fermented by Clostridium spp. and Bacteroides spp. to produce propionate or ethanol, which were subsequently utilized by Desulfobulbus spp. and Desulfovibrio spp. The acidotrophic SRB oxidized part of the acetate finally.     

Photolysis of low concentration H2S under UV/VUV irradiation emitted from microwave discharge electrodeless lamps

The photolysis of simulating low concentration of hydrogen sulfide malodorous gas was studied under UV irradiation emitted by self-made microwave discharge electrodeless lamps (i.e. microwave UV electrodeless mercury lamp (185/253.7 nm) and iodine lamp (178.3/180.1/183/184.4/187.6/206.2 nm)). Experiments results showed that the removal efficiency (eta H2S) of hydrogen sulfide was decreased with increasing initial H2S concentration and increased slightly with gas residence time; H2S removal efficiency was decreased dramatically with enlarged pipe diameter. Under the experimental conditions with pipe diameter of 36 mm, gas flow rate of 0.42 standard l s(-1), eta H2S was 52% with initial H2S concentration of 19.5 mg m(-3) by microwave mercury lamp, the absolute removal amount (ARA) was 4.30 microg s(-1), and energy yield (EY) was 77.3 mg kW h(-1); eta H2S was 56% with initial H2S concentration of 18.9 mg m(-3) by microwave iodine lamp, the ARA was 4.48 microg s(-1), and the EY was 80.5mg kW h(-1). The main photolysis product was confirmed to be SO4(2-) with IC.     

Biotreatment of hydrogen sulfide- and ammonia-containing waste gases by fluidized bed bioreactor

Gas mixtures of H2S and NH3 are the focus of this study of research concerning gases generated from animal husbandry and treatments of anaerobic wastewater lagoons. A heterotrophic microflora (a mixture of Pseudomonas putida for H2S and Arthrobacter oxydans for NH3) was immobilized with Ca-alginate and packed into a fluidized bed reactor to simultaneously decompose H2S and NH3. This bioreactor was continuously supplied with H2S and NH3 separately or together at various ratios. The removal efficiency, removal rate, and metabolic product of the bioreactor were studied. The results showed that the efficiency remained above 95% when the inlet H2S concentration was below 30 ppm at 36 L/hr. Furthermore, the apparent maximum removal and the apparent half-saturation constant were 7.0 x 10(-8) g-S/cell/day and 76.2 ppm, respectively, in this study. The element sulfur as a main product prevented acidification of the biofilter, which maintained the stability of the operation. As for NH3, the greater than 90% removal rate was achieved as long as the inlet concentration was controlled below 100 ppm at a flow rate of 27 L/hr. In the NH3 inlet, the apparent maximum removal and the apparent half-saturation constant were 1.88 x 10(-6) g-N/cell/day and 30.5 ppm, respectively. Kinetic analysis showed that 60 ppm of NH3 significantly suppressed the H2S removal by Pseudomonas putida, but H2S in the range of 5-60 ppm did not affect NH3 removal by Arthrobacter oxydans. Results from bioaerosol analysis in the bioreactor suggest that the co-immobilized cell technique applied for gas removal creates less environmental impact.     

等离子体协同光催化去除模拟烟气中SO2的实验研究

近年来,低温等离子体技术以及纳米TiO₂光催化技术在烟气脱硫中的应用越来越引起人们的关注。利用填充床反应器将这2种技术有机地结合起来，进行了大量脱硫实验研究。研究结果表明，等离子体协同光催化去除烟气中的SO₂与单独采用等离子体技术相比，其SO₂的去除率可提高5%～20%。同时，探讨了等离子体协同TiO₂光催化剂的脱硫机理，分别研究了外加电压、气体流量和SO₂初始浓度等因素对脱硫效率的影响。实验结果表明，当SO₂初始浓度为800 mg/m³，输入电压为17.5 kV，气体流量为0.2 m³/h时，SO₂脱除率可以达到77.6%。     

生物滴滤池脱除烟气中SO2的实验研究

将分离筛选得到的氧化亚铁硫杆菌固定在生物滴滤池的填料上,组成生物滴滤池反应系统,并研究了进气SO2浓度、气体流量、液气比、循环液中铁离子浓度对脱硫效率的影响,此外还分析了该反应系统的脱硫机理.