Characterization of Air Quality Problems in Five Finnish Indoor Ice Arenas

ABSTRACT

The air quality in five Finnish ice arenas with different volumes, ventilation systems, and resurfacer power sources (propane, gasoline, electric) was monitored during a usual training evening and a standardized, simulated ice hockey game. The measurements included continuous recording of carbon monoxide (CO), nitric oxide (NO), and nitrogen dioxide (NO₂) concentrations, and sampling and analysis of volatile organic compounds (VOCs). Emissions from the ice resurfacers with combustion engines caused indoor air quality problems in all ice arenas. The highest 1-hour average CO and NO₂ concentrations ranged from 20 to 33 mg/m³ (17 to 29 ppm) and 270 to 7440 µg/m³ (0.14 to 3.96 ppm), respectively. The 3-hour total VOC concentrations ranged from 150 to 1200 µg/m³. The highest CO and VOC levels were measured in the arena in which a gasoline-fueled resurfacer was used. The highest NO₂ levels were measured in small ice arenas with propane-fueled ice resurfacers and insufficient ventilation.

In these arenas, the indoor NO₂ levels were about 100 times the levels measured in ambient outdoor air, and the highest 1-hour concentrations were about 20 times the national and World Health Organization (WHO) health-based air quality guidelines. The air quality was fully acceptable only in the arena with an electric resurfacer. The present study showed that the air quality problems of indoor ice arenas may vary with the fuel type of resurfacer and the volume and ventilation of arena building. It also confirmed that there are severe air quality problems in Finnish ice arenas similar to those previously described in North America.     

Summer air quality over an artificial lake

In the summer of 1998, the air quality (indicators: CO, NO, NO₂, O₃) above the water surface of the Lake Balderey (Essen, Ruhr area, North Rhine-Westphalia, Germany), an artificial lake used for recreation purposes, was measured using the Fourier transform infrared spectroscopy (FTIR) and differential optical absorption spectroscopy (DOAS) remote measurement methods. The lake, with an area of 3 km² was created by damming the Ruhr and is surrounded by higher ground. In calm, bright weather conditions, this location results in a low-exchange situation (formation of temperature inversions, cold air dynamics) with a sustained impact on pollutant concentrations over the lake. The results of trace substance measurements (1/2 h mean values) were compared with values from comparison stations (suburban, high traffic and forest) located outside the area of the lake. In general, it was found that mean CO and NO concentrations over the lake were very low (0.3 ppm and 7.5 ppb, respectively). NO₂ values (15 ppb) were some 3.5 times higher than those recorded at the forest station and O₃ values, at 27 ppb, almost reached the same level as at the forest station (30 ppb). Mass flow densities as a function of wind direction, diurnal courses, differences between weekdays and weekends and comparisons with air quality standards are presented for the lake station.     

Analysis of air quality in Dire Dawa,Ethiopia

Ambient air quality was monitored and analyzed to develop air quality index and its implications for livability and climate change in Dire Dawa, Ethiopia. Using survey research design, 16 georeferenced locations, representing different land uses, were randomly selected and assessed for sulfur dioxide (SO₂), nitrogen dioxide (NO₂), carbon dioxide (CO₂), carbon monoxide (CO),volatile organic compounds (VOCs), and meteorological parameters (temperature and relative humidity). The study found mean concentrations across all land uses for SO₂ of 0.37 ± 0.08 ppm, NO₂ of 0.13 ± 0.17 ppm, CO₂ of 465.65 ± 28.63 ppm, CO of 3.35 ± 2.04 ppm, and VOCs of 1850.67 ± 402 ppm. An air quality index indicated that ambient air quality for SO₂ was very poor, NO₂ ranged from moderate to very poor, whereas CO rating was moderate. Significant positive correlations existed between temperature and NO₂, CO₂, and CO and between humidity and VOCs. Significant relationships were also recorded between CO₂ and NO₂ and between CO and CO₂. Poor urban planning, inadequate pollution control measure, and weak capacity to monitor air quality have implications for energy usage, air quality, and local meteorological parameters, with subsequent feedback into global climate change. Implementation of programs to monitor and control emissions in order to reduce air pollution will provide health, economic, and environmental benefits to the city.

Implications: The need to develop and implement emission control programs to reduce air pollution in Dire Dawa City is urgent. This will provide enormous economic, health, and environmental benefits. It is expected that economic effects of air quality improvement will offset the expenditures for pollution control. Also, strategies that focus on air quality and climate change present a unique opportunity to engage different stakeholders in providing inclusive and sustainable development agenda for Dire Dawa.     

Fine particles and carbon monoxide from wood burning in 17th–19th century Danish kitchens: Measurements at two reconstructed farm houses at the Lejre Historical–Archaeological Experimental Center

Carbon monoxide (CO) and particulate matter (PM_2.5) were measured in two reconstructed Danish farmhouses (17–19th century) during two weeks of summer. During the first week intensive measurements were performed while test cooking fires were burned, during the second week the houses were monitored while occupied by guest families. A masonry hearth was located in the middle of each house for open cooking fires and with heating stoves. One house had a chimney leading to the outside over the hearth; in the other, a brickwork hood led the smoke into an attic and through holes in the roof. During the first week the concentration of PM_2.5 averaged daily between 138 and 1650 μg m^?3 inside the hearths and 21–160 μg m^?3 in adjacent living rooms. CO averaged daily between 0.21 and 1.9 ppm in living areas, and up to 12 ppm in the hearths. Highest concentrations were measured when two fires were lit at the same time, which would cause high personal exposure for someone working in the kitchens. 15 min averages of up to 25 400 μg m^?3 (PM_2.5) and 260 ppm CO were recorded. WHO air quality guidelines were occasionally exceeded for CO and constantly for PM_2.5. However, air exchange and air distribution measurements revealed a large draw in the chimney, which ensured a fast removal of wood smoke from the hearth area. The guest families were in average exposed to no more than 0.21 ppm CO during 48 h. Based on a hypothetical time-activity pattern, however, a woman living in this type of house during the 17–19th century would be exposed to daily averages of 1.1 ppm CO and 196 μg m^?3 PM_2.5, which exceeds WHO guideline for PM_2.5, and is comparable to what is today observed for women in rural areas of developing countries.     

Tetrachloroethylene Emissions and Exposure in Dry Cleaning

ABSTRACT

Tetrachloroethylene (PCE) emissions and the exposure of workers in six commercial and three industrial dry-cleaning establishments that use dry-to-dry machines were determined. The personal samples and area samples [8-hr time-weighted average (TWA) and short-term exposure] were collected with charcoal tubes and passive monitors. The temporal variation of PCE concentration in the workplace air was monitored using a Fourier transform infrared analyzer (FTIR). The PCE emission rates were determined by multiplying the average PCE concentration in the room and the total airflow rate in the room. The PCE emissions were related to the cleaning rate in units of kg/hr.

The operators' mean TWA exposure in commercial shops and industrial establishments was 28 (4.1 ppm) and 32 mg/m³ (4.6 ppm), and the pressers' exposure was 3.4 (0.5 ppm) and 7.7 mg/m³ (1.1 ppm), respectively. The customer service personnel had the lowest TWA exposure with a mean value of 0.8 mg/m³ (0.1 ppm). The highest peak concentration (2300 mg/m³; 334 ppm) was observed during cleaning of the lint and button trap, during which operation respirators were used. The PCE emission rates ranged from 4 to 118 g/hr corresponding to emission factors (mass of solvent evaporated per mass of cleaned cloths) of 0.3–3.6 g/kg. The workers' exposure to PCE was below the occupational limit values in the United States [according to the American Conference of Governmental Industrial Hygienists (ACGIH)] and in Finland. The outdoor PCE emissions were clearly below the limit values given in the European Union volatile organic compound (VOC) directive requirements.     

Meta-Analysis of Time-Series Studies of Air Pollution and Mortality: Effects of Gases and Particles and the Influence of Cause of Death,Age, and Season

Abstract

A comprehensive, systematic synthesis was conducted of daily time-series studies of air pollution and mortality from around the world. Estimates of effect sizes were extracted from 109 studies, from single- and multipollutant models, and by cause of death, age, and season. Random effects pooled estimates of excess all-cause mortality (single-pollutant models) associated with a change in pollutant concentration equal to the mean value among a representative group of cities were 2.0% (95% CI 1.5-2.4%) per 31.3 μg/m³ particulate matter (PM) of median diameter <10 μm (PM₁₀); 1.7% (1.2-2.2%) per 1.1 ppm CO; 2.8% (2.1-3.5%) per 24.0 ppb NO₂; 1.6% (1.1-2.0%) per 31.2 ppb O₃; and 0.9% (0.7-1.2%) per 9.4 ppb SO₂ (daily maximum concentration for O₃, daily average for others). Effect sizes were generally reduced in multipollutant models, but remained significantly different from zero for PM₁₀ and SO₂. Larger effect sizes were observed for respiratory mortality for all pollutants except O₃. Heterogeneity among studies was partially accounted for by differences in variability of pollutant concentrations, and results were robust to alternative approaches to selecting estimates from the pool of available candidates. This synthesis leaves little doubt that acute air pollution exposure is a significant contributor to mortality.     

Expected Decline in Carboxyhemogldbin Levels As Related to Automobile Carbon Monoxide Emission Standards

Carboxyhemoglobin (COHb) levels in blood are principally due to inhalation of carbon monoxide, although a low level (approximately 0.3%) of COHb is endogenous. A carboxyhemoglobin level above 1.5 % in non-smokers indicates exposure to CO in excess of the 10 mg/m³ air quality standard established under the Clean Air Act Amendments of 1970.

In most major U.S. cities, automobile emissions constitute the principal source of CO; in Chicago, according to EPA estimates,¹ light duty vehicles are responsible for 69.3% of all CO emissions. Thus as new automobiles incorporating emission controls enter the automotive fleet and older, emission-uncontrolled automobiles are phased out, ambient CO concentrations should decline and corresponding reductions in blood carboxyhemoglobin levels of nonsmokers can be expected.     

Hazardous emissions and concentrations of toxic metalloids and trace elements in charcoals from six commonly used tropical timbers for carbonization

Carbonized wood is a biofuel from cellulose pyrolysis with frequent smoke and life-threatening carcinogenic emissions. Carbon monoxide (CO), particulate matter (PM_2.5), metalloids and trace elements from charcoals from six commonly used tropical timbers for carbonization in Donkorkrom (Ghana) were assessed. During combustion, Anogeissus leiocarpa charcoal emitted the least CO (4.28 ± 1.08 ppm) and PM_2.5 (3.83 ± 1.57 μg/m³), while particulate matter was greatest for Erythrophleum ivorense (28.05 ± 3.08 ppm) and Azadirachta indica (27.67 ± 4.17 μg/m³) charcoals. Erythrophleum ivorense charcoal produced much lead (16.90 ± 0.33 ppm), arsenic (1.97 ± 0.10 ppm) and mercury (0.58 ± 0.003 ppm) but the least chromium (0.11 ± 0.01 ppm) and zinc (2.85 ± 0.05 ppm). Nickel was greatest for A. indica charcoal (0.71 ± 0.01 ppm) and least for Vitellaria paradoxa (0.07 ± 0.004 ppm). Trace elements ranged from 342.01 ± 2.54 ppm (A. indica) to 978.47 ± 1.80 ppm (V. paradoxa) for potassium and 1.74 ± 0.02% (V. paradoxa) to 2.24 ± 0.10% (A. indica) for sulphur. Besides A. leiocarpa charcoal, which ranked safest during combustion, the high PM_2.5 and CO emissions make the other biofuels hazardous indoors. Kitchens need air filters to absorb these emissions together with the use of improved cook stoves. These carcinogenic metalloids would necessitate that their ashes be properly discarded without human contact. Yet, the charcoals would be much suitable as soil amendment bio-char for plant growth quality improvement.

     

Source apportionment of emissions from light-duty gasoline vehicles and other sources in the United States for ozone and particulate matter

Federal Tier 3 motor vehicle emission and fuel sulfur standards have been promulgated in the United States to help attain air quality standards for ozone and PM_2.5 (particulate matter with an aerodynamic diameter <2.5 μm). The authors modeled a standard similar to Tier 3 (a hypothetical nationwide implementation of the California Low Emission Vehicle [LEV] III standards) and prior Tier 2 standards for on-road gasoline-fueled light-duty vehicles (gLDVs) to assess incremental air quality benefits in the United States (U.S.) and the relative contributions of gLDVs and other major source categories to ozone and PM_2.5 in 2030. Strengthening Tier 2 to a Tier 3-like (LEV III) standard reduces the summertime monthly mean of daily maximum 8-hr average (MDA8) ozone in the eastern U.S. by up to 1.5 ppb (or 2%) and the maximum MDA8 ozone by up to 3.4 ppb (or 3%). Reducing gasoline sulfur content from 30 to 10 ppm is responsible for up to 0.3 ppb of the improvement in the monthly mean ozone and up to 0.8 ppb of the improvement in maximum ozone. Across four major urban areas—Atlanta, Detroit, Philadelphia, and St. Louis—gLDV contributions range from 5% to 9% and 3% to 6% of the summertime mean MDA8 ozone under Tier 2 and Tier 3, respectively, and from 7% to 11% and 3% to 7% of the maximum MDA8 ozone under Tier 2 and Tier 3, respectively. Monthly mean 24-hr PM_2.5 decreases by up to 0.5 μg/m³ (or 3%) in the eastern U.S. from Tier 2 to Tier 3, with about 0.1 μg/m³ of the reduction due to the lower gasoline sulfur content. At the four urban areas under the Tier 3 program, gLDV emissions contribute 3.4–5.0% and 1.7–2.4% of the winter and summer mean 24-hr PM_2.5, respectively, and 3.8–4.6% and 1.5–2.0% of the mean 24-hr PM_2.5 on days with elevated PM_2.5 in winter and summer, respectively.

Implications: Following U.S. Tier 3 emissions and fuel sulfur standards for gasoline-fueled passenger cars and light trucks, these vehicles are expected to contribute less than 6% of the summertime mean daily maximum 8-hr ozone and less than 7% and 4% of the winter and summer mean 24-hr PM_2.5 in the eastern U.S. in 2030. On days with elevated ozone or PM_2.5 at four major urban areas, these vehicles contribute less than 7% of ozone and less than 5% of PM_2.5, with sources outside North America and U.S. area source emissions constituting some of the main contributors to ozone and PM_2.5, respectively.     

Assessment of air quality benefits from national air pollution control policies in China. Part II: Evaluation of air quality predictions and air quality benefits assessment

Following the meteorological evaluation in Part I, this Part II paper presents the statistical evaluation of air quality predictions by the U.S. Environmental Protection Agency (U.S. EPA)’s Community Multi-Scale Air Quality (Models-3/CMAQ) model for the four simulated months in the base year 2005. The surface predictions were evaluated using the Air Pollution Index (API) data published by the China Ministry of Environmental Protection (MEP) for 31 capital cities and daily fine particulate matter (PM_2.5, particles with aerodiameter less than or equal to 2.5 μm) observations of an individual site in Tsinghua University (THU). To overcome the shortage in surface observations, satellite data are used to assess the column predictions including tropospheric nitrogen dioxide (NO₂) column abundance and aerosol optical depth (AOD). The result shows that CMAQ gives reasonably good predictions for the air quality.The air quality improvement that would result from the targeted sulfur dioxide (SO₂) and nitrogen oxides (NO_x) emission controls in China were assessed for the objective year 2010. The results show that the emission controls can lead to significant air quality benefits. SO₂ concentrations in highly polluted areas of East China in 2010 are estimated to be decreased by 30–60% compared to the levels in the 2010 Business-As-Usual (BAU) case. The annual PM_2.5 can also decline by 3–15 μg m^?3 (4–25%) due to the lower SO₂ and sulfate concentrations. If similar controls are implemented for NO_x emissions, NO_x concentrations are estimated to decrease by 30–60% as compared with the 2010 BAU scenario. The annual mean PM_2.5 concentrations will also decline by 2–14 μg m^?3 (3–12%). In addition, the number of ozone (O₃) non-attainment areas in the northern China is projected to be much lower, with the maximum 1-h average O₃ concentrations in the summer reduced by 8–30 ppb.     

Exposure to hazardous air pollutants along Oba Akran road, Lagos-Nigeria

We measured toxic air pollutants along Oba Akran road in Lagos to evaluate pedestrian exposure. PM₁₀, CO, O₃, NO₂, SO₂, CH₄, noise, wind velocity and temperature were measured simultaneously with portable analyzers. Our results showed that pedestrian exposure to PM₁₀ (with an average of 274.6 μg m⁻³ for all samples) and CO (with an average of 19.27 ppm for all samples) was relatively high. CO is a traffic-related pollutant, so the influence of the local traffic emissions on CO levels is strong. The high concentration of the PM₁₀ measured at the three environments also suggests that the traffic is a major source of ultrafine particles. The overall average concentrations for the 72-day experimental period for SO₂, NO₂ and O₃ are 101.2, 62.5 and 0.32 ppb respectively, all of which are below the US national ambient air quality standards. Strong traffic impacts can be observed from the concentrations of some of these pollutants measured in these three environments. Most clear is a reflection of diesel truck traffic activity rich in black carbon concentrations. The diurnal variation of O₃ and NO₂ also showed that NO₂ was depleted by photochemically formed O₃ during the day and replenished at night as O₃ was destroyed. A multivariate statistical analysis (Principal Component Analysis, Factor Analysis) has been applied to a set of data in order to determine the contribution of different sources. It was found that the main principal components, extracted from the air pollution data, were related to gasoline combustion, oil combustion and ozone interactions.     

Recent spatial gradients and time trends in Dhaka,Bangladesh, air pollution and their human health implications

Dhaka, the capital of Bangladesh, is among the most polluted cities in the world. This research evaluates seasonal patterns, day-of-week patterns, spatial gradients, and trends in PM_2.5 (<2.5 µm in aerodynamic diameter), PM₁₀ (<10 µm in aerodynamic diameter), and gaseous pollutants concentrations (SO₂, NO₂, CO, and O₃) monitored in Dhaka from 2013 to 2017. It expands on past work by considering multiple monitoring sites and air pollutants. Except for ozone, the average concentrations of these pollutants showed strong seasonal variation, with maximum during winter and minimum during monsoon, with the pollution concentration of PM_2.5 and PM₁₀ being roughly five- to sixfold higher during winter versus monsoon. Our comparisons of the pollutant concentrations with Bangladesh NAAQS and U.S. NAAQS limits analysis indicate particulate matter (PM_2.5 and PM₁₀) as the air pollutants of greatest concern, as they frequently exceeded the Bangladesh NAAQS and U.S. NAAQS, especially during nonmonsoon time. In contrast, gaseous pollutants reported far fewer exceedances throughout the study period. During the study period, the highest number of exceedances of NAAQS limits in Dhaka City (Darus-Salam site) were found for PM_2.5 (72% of total study days), followed by PM₁₀ (40% of total study days), O₃ (1.7% of total study days), SO₂ (0.38% of total study days), and CO (0.25% of total study days). The trend analyses results showed statistically significant positive slopes over time for SO₂ (5.6 ppb yr^?1, 95% confidence interval [CI]: 0.7, 10.5) and CO (0.32 ppm yr^?1, 95% CI: 0.01, 0.56), which suggest increase in brick kilns operation and high-sulfur diesel use. Though statistically nonsignificant annual decreasing slopes for PM_2.5 (?4.6 µg/m³ yr^?1, 95% CI: ?12.7, 3.6) and PM₁₀ (?2.7 µg/m³ yr^?1, 95% CI: ?7.9, 2.5) were observed during this study period, the PM_2.5 concentration is still too high (~ 82.0 µg/m³) and can cause severe impact on human health.

Implications: This study revealed key insights into air quality challenges across Dhaka, Bangladesh, indicating particulate matter (PM) as Dhaka’s most serious air pollutant threat to human health. The results of these analyses indicate that there is a need for immediate further investigations, and action based on those investigations, including the conduct local epidemiological PM exposure-human health effects studies for this city, in order to determine the most public health effective interventions.     

Air quality and health benefits from potential coal power plant closures in Texas

As power production from renewable energy and natural gas grows, closures of some coal-fired power plants in Texas become increasingly likely. In this study, the potential effects of such closures on air quality and human health were analyzed by linking a regional photochemical model with a health impacts assessment tool. The impacts varied significantly across 13 of the state’s largest coal-fired power plants, sometimes by more than an order of magnitude, even after normalizing by generation. While some power plants had negligible impacts on concentrations at important monitors, average impacts up to 0.5 parts per billion (ppb) and 0.2 µg/m³ and maximum impacts up to 3.3 ppb and 0.9 µg/m³ were seen for ozone and fine particulate matter (PM_2.5), respectively. Individual power plants impacted average visibility by up to 0.25 deciviews in Class I Areas. Health impacts arose mostly from PM_2.5 and were an order of magnitude higher for plants that lack scrubbers for SO₂. Rankings of health impacts were largely consistent across the base model results and two reduced form models. Carbon dioxide emissions were relatively uniform, ranging from 1.00 to 1.26 short tons/MWh, and can be monetized based on a social cost of carbon. Despite all of these unpaid externalities, estimated direct costs of each power plant exceeded wholesale power prices in 2016.

Implications: While their CO₂ emission rates are fairly similar, sharply different NO_x and SO₂ emission rates and spatial factors cause coal-fired power plants to vary by an order of magnitude in their impacts on ozone, particulate matter, and associated health and visibility outcomes. On a monetized basis, the air pollution health impacts often exceed the value of the electricity generated and are of similar magnitude to climate impacts. This suggests that both air pollution and climate should be considered if externalities are used to inform decision making about power-plant dispatch and retirement.     

Characterization of indoor air quality and resident health in an Arizona senior housing apartment building

A survey of key indoor air quality (IAQ) parameters and resident health was carried out in 72 apartments within a single low-income senior housing building in Phoenix, Arizona. Air sampling was carried out simultaneously with a questionnaire on personal habits and general health of residents. Mean PM₁₀ concentrations are 66±16, 58±13, and 24±3 μg/m³ and mean PM_2.5 concentrations are 62±16, 53±13, and 20±2 μg/m³ for the living room, kitchen, and outdoor balcony, respectively. Median PM₁₀ concentrations are 17, 18 and 17 μg/m³ and median PM_2.5 concentrations are 13, 14, and 13 μg/m³, respectively. The initial results indicate that increased indoor particle concentrations coincide with residents who report smoking cigarettes. Indoor formaldehyde concentrations revealed median levels of 36.9, 38.8, and 4.3 ppb in the living room, kitchen, and balcony, respectively. Results show that 36% of living room samples and 44% of kitchen samples exceeded the Health Canada REL for chronic exposure to formaldehyde (40 ppb). Associations between occupants’ behavior, self-reported health conditions, and IAQ are evaluated.

Implications:This study provides a characterization of indoor air quality (IAQ) of subsidized apartments for seniors in Phoenix, Arizona. It is important for policy makers to understand the environments in which low-income seniors live, as they are vulnerable to the health impacts from poor IAQ. Formaldehyde concentrations were found to exceed the Health Canada 8-hr reference exposure level (REL) for up to 44% of indoor samples. Particulate matter exposure was governed by resident behavior (i.e., smoking). Associations between occupants’ behavior, IAQ, and self-reported health conditions are evaluated. This work can provide a foundation for subsequent remediation of IAQ conditions.     

Collaborative Testing of Methods to Measure Air Pollutants II. The Non-Dispersive Infrared Method for Carbon Monoxide

The Methods Standardization Branch of the Environmental Protection Agency, National Environmental Research Center, has undertaken a program to standardize methods used in measuring air pollutants covered by the national primary and secondary air quality standards. This paper presents the results of a collaborative test of the method specified for carbon monoxide.

The test involved analysis of CO in air samples (in cylinders) by participating laboratories. Three concentrations, covering the range of the method which is, 0 to 58 mg/m³, were analyzed dry and humidified on each of three days by 15 collaborators. The method of analysis, nondispersive infrared spectrometry (NDIR), involved an NDIR instrument in combination with different procedures for eliminating water vapor interference. A statistical analysis of the data obtained produced the following results: 1. The checking limit for duplicates (replication error) is 0.5 mg/m³.

2. The repeatability (variation within a laboratory) is 1.6 mg/m³.

3. The reproducibility (variation between laboratories) varies nonlinearly with concentration; i.e., a minimum of 2.3 mg/m³ at a concentration of 20 mg/m³ and ranges as high as 4.3 mg/m³ in the concentration range of 0 to 58 mg/m³.

4. The reproducibility at the level of the national primary ambient air quality standard, 10 mg/m³-8-hour average, is 2.5 mg/m³ or 25%.

5. The minimum detectable sensitivity is estimated to be 0.3 mg/m³.

6. Compensation for water vapor interference is satisfactorily accomplished using drying agents and refrigeration methods. The use of narrow-band optical filters alone may not provide adequate compensation.

7. The accuracy obtained depends upon the availability of reliable calibration gases. Based on the results of this study, the method produces results that average 2.5% high.

Future papers will contain test results for methods to measure other air pollutants.     

Fugitive Dust Emission Source Profiles and Assessment of Selected Control Strategies for Particulate Matter at Gravel Processing Sites in Taiwan

Abstract

Particles emitted from gravel processing sites are one contributor to worsening air quality in Taiwan. Major pollution sources at gravel processing sites include gravel and sand piles, unpaved roads, material crushers, and bare ground. This study analyzed fugitive dust emission characteristics at each pollution source using several types of particle samplers, including total suspended particulates (TSP), suspended particulate (PM₁₀), fine suspended particulate (PM_2.5), particulate sizer, and dust-fall collectors. Furthermore, silt content and moisture in the gravel were measured to develop particulate emission factors. The results showed that TSP (<100 µm) concentrations at the boundary of gravel sites ranged from 280 to 1290 µg/m³, which clearly exceeds the Taiwan hourly air quality standard of 500 µg/m³. Moreover, PM₁₀ concentrations, ranging from 135 to 550 µg/m³, were also above the daily air quality standard of 125 µg/m³ and approximately 1.2 and 1.5 times the PM_2.5 concentrations, ranging from 105 to 470 µg/m³. The size distribution analysis reveals that mass mean diameter and geometric standard deviation ranged from 3.2 to 5.7 µm and from 2.82 to 5.51, respectively. In this study, spraying surfactant was the most effective control strategy to abate windblown dust from unpaved roads, having a control efficiency of approximately 93%, which is significantly higher than using paved road strategies with a control efficiency of approximately 45%. For paved roads, wet suppression provided the best dust control efficiencies ranging from 50 to 83%. Re-vegetation of disturbed ground had dust control efficiencies ranging from 48 to 64%.     

Radical precursors and related species from traffic as observed and modeled at an urban highway junction

Nitrous acid (HONO) and formaldehyde (HCHO) are important precursors for radicals and are believed to favor ozone formation significantly. Traffic emission data for both compounds are scarce and mostly outdated. A better knowledge of today's HCHO and HONO emissions related to traffic is needed to refine air quality models. Here the authors report results from continuous ambient air measurements taken at a highway junction in Houston, Texas, from July 15 to October 15, 2009. The observational data were compared with emission estimates from currently available mobile emission models (MOBILE6; MOVES [MOtor Vehicle Emission Simulator]). Observations indicated a molar carbon monoxide (CO) versus nitrogen oxides (NO_x) ratio of 6.01 ± 0.15 (r ² = 0.91), which is in agreement with other field studies. Both MOBILE6 and MOVES overestimate this emission ratio by 92% and 24%, respectively. For HCHO/CO, an overall slope of 3.14 ± 0.14 g HCHO/kg CO was observed. Whereas MOBILE6 largely underestimates this ratio by 77%, MOVES calculates somewhat higher HCHO/CO ratios (1.87) than MOBILE6, but is still significantly lower than the observed ratio. MOVES shows high HCHO/CO ratios during the early morning hours due to heavy-duty diesel off-network emissions. The differences of the modeled CO/NO_x and HCHO/CO ratios are largely due to higher NO_x and HCHO emissions in MOVES (30% and 57%, respectively, increased from MOBILE6 for 2009), as CO emissions were about the same in both models. The observed HONO/NO_x emission ratio is around 0.017 ± 0.0009 kg HONO/kg NO_x which is twice as high as in MOVES. The observed NO₂/NO_x emission ratio is around 0.16 ± 0.01 kg NO₂/kg NO_x, which is a bit more than 50% higher than in MOVES. MOVES overestimates the CO/CO₂ emission ratio by a factor of 3 compared with the observations, which is 0.0033 ± 0.0002 kg CO/kg CO₂. This as well as CO/NO_x overestimation is coming from light-duty gasoline vehicles.

Implications: Nitrous acid (HONO) and formaldehyde (HCHO) are important precursors for radicals that ultimately contribute to ozone formation. There still exist uncertainties in emission sources of HONO and HCHO and thus regional air quality modeling still tend to underestimate concentrations of free radicals in the atmosphere. This paper demonstrates that the latest U.S. Environmental Protection Agency (EPA) traffic emission model MOVES still shows significant deviations from observed emission ratios, in particular underestimation of HCHO/CO and HONO/NO_x ratios. Improving the performance of MOVES may improve regional air quality modeling.     

Temporal distribution and potential sources of atmospheric mercury measured at a high-elevation background station in Taiwan

Measurements of gaseous elemental mercury (GEM), reactive gaseous mercury (RGM), and particulate mercury (PHg) have been conducted at Lulin Atmospheric Background Station (LABS) in Taiwan since April 2006. This was the first long-term free tropospheric atmospheric Hg monitoring program in the downwind region of East Asia, which is a major Hg emission source region. Between April 13, 2006 and December 31, 2007, the mean concentrations of GEM, RGM, and PHg were 1.73 ng m^?3, 12.1 pg m^?3, and 2.3 pg m^?3, respectively. A diurnal pattern was observed for GEM with afternoon peaks and nighttime lows, whereas the diurnal pattern of RGM was opposite to that of GEM. Spikes of RGM were frequently observed between midnight and early morning with concurrent decreases in GEM and relative humidity and increases in O₃, suggesting the oxidation of GEM and formation of RGM in free troposphere (FT). Upslope movement of boundary layer (BL) air in daytime and subsidence of FT air at night resulted in these diurnal patterns. Considering only the nighttime data, which were more representative of FT air, the composite monthly mean GEM concentrations ranged between 1.06 and 2.06 ng m^?3. Seasonal variation in nighttime GEM was evident, with lower concentrations usually occurring in summer when clean marine air masses prevailed. Between fall and spring, air masses passed the East Asian continent prior to reaching LABS, contributing to the elevated GEM concentrations. Analysis of GEM/CO correlation tends to support the argument. Good GEM/CO correlations were observed in fall, winter, and spring, suggesting influence of anthropogenic emission sources. Our results demonstrate the significance of East Asian Hg emissions, including both anthropogenic and biomass burning emissions, and their long-range transport in the FT. Because of the pronounced seasonal monsoon activity and the seasonal variation in regional wind field, export of the Asian Hg emissions to Taiwan occurs mainly during fall, winter, and spring.     

Exposure of acid aerosol for schoolchildren in metropolitan Taipei

Metropolitan Taipei, which is located in the subtropical area, is characterized by high population and automobile densities. For convenience, most primary schools are located near major roads. This study explores the exposure of acid aerosols for schoolchildren in areas in Taipei with different traffic densities. Acid aerosols were collected by using a honeycomb denuder filter pack sampling system (HDS). Experimental results indicated that the air pollutants were significantly correlated with traffic densities. The ambient air NO₂, SO₂, HNO₃, NO₃⁻, SO₄²⁻, and aerosol acidity concentrations were 31.3 ppb, 4.7 ppb, 1.3 ppb, 1.9 μg m⁻³, 18.5 μg m⁻³, and 49.5 nmol m⁻³ in high traffic density areas, and 6.1 ppb, 1.8 ppb, 0.9 ppb, 0.7 μg m⁻³, 8.8 μg m⁻³ and 14.7 nmol m⁻³ in low traffic density areas. The exposure levels of acid aerosols for schoolchildren would be higher than the measurements because the sampling height was 5 m above the ground. The SO₂ levels were low (0.13–8.03 ppb) in the metropolitan Taipei. However, the SO₄²⁻ concentrations were relatively high, and might be attributed to natural emissions of sulfur-rich geothermal sources. The seasonal variations of acid aerosol concentrations were also observed. The high levels of acidic particles in spring time may be attributed to the Asian dust storm and low height of the mixture layer. We conclude that automobile contributed not only the primary pollutants but also the secondary acid aerosols through the photochemical reaction. Schoolchildren were exposed to twice the acid aerosol concentrations in high traffic density areas compared to those in low traffic density areas. The incidence of allergic rhinitis of schoolchildren in the high traffic density areas was the highest in spring time. Accompanied by high temperature variation and high levels of air pollution in spring, the health risk of schoolchildren had been observed.     

Sulfuric odorous compounds emitted from pig-feeding operations

The objective of the study was to quantify the concentration and emission levels of sulfuric odorous compounds emitted from pig-feeding operations. Five types of pig-housing rooms were studied: gestation, farrowing, nursery, growing and fattening rooms. The concentration range of sulfuric odorous compounds in these pig-housing rooms were 30–200 ppb for hydrogen sulfide (H₂S), 2.5–20 ppb for methyl mercaptan (CH₃SH), 1.5–12 ppb for dimethyl sulfide (DMS; CH₃SCH₃) and 0.5–7 ppb for dimethyl disulfide (DMDS; CH₃S₂CH₃), respectively. The emission rates of H₂S, CH₃SH, DMS and DMDS were estimated by multiplying the average concentration (mg m⁻³) measured near the air outlet by the mean ventilation rate (m³ h⁻¹) and expressed either per area (mg m⁻² h⁻¹) or animal unit (AU; liveweight of the pig, 500 kg) (mg pig⁻¹ h⁻¹). As a result, the emission rates of H₂S, CH₃SH, DMS and DMDS in the pig-housing rooms were 14–64, 0.8–7.3, 0.4–3.4 and 0.2–1.9 mg m⁻² h⁻¹, respectively, based on pig's activity space and 310–723, 18–80, 9–39 and 5–22 mg AU⁻¹ h⁻¹, respectively, based on pig's liveweight, which indicates that their emission rates were similar, whether based upon the pig's activity space or liveweight. In conclusion, the concentrations and emission rates of H₂S were highest in the fattening room followed by the growing, nursery, farrowing and gestation rooms whereas those of CH₃SH, DMS and DMDS concentrations were largest in the growing room followed by the nursery, gestation and farrowing rooms.