Rapid quantification of polycyclic aromatic hydrocarbons in hydroxypropyl-beta-cyclodextrin (HPCD) soil extracts by synchronous fluorescence spectroscopy (SFS)

Synchronous fluorescence spectroscopy (SFS) was directly applied to rapidly quantify selected polycyclic aromatic hydrocarbons (PAHs: benzo[a]pyrene and pyrene) in aqueous hydroxypropyl-beta-cyclodextrin (HPCD) soil extract solutions from a variety of aged contaminated soils containing four different PAHs. The method was optimized and validated. The results show that SFS can be used to analyse benzo[a]pyrene and pyrene in HPCD based soil extracts with high sensitivity and selectivity. The linear calibration ranges were 4.0x10(-6)-1.0x10(-3)mM for benzo[a]pyrene and 6.0x10(-6)-1.2x10(-3)mM for pyrene in 10mM HPCD aqueous solution alone. The detection limits according to the error propagation theory for benzo[a]pyrene and pyrene were 3.9x10(-6) and 5.4x10(-6)mM, respectively. A good agreement between SFS and HPLC was reached for both determinations of PAHs in HPCD alone and in soil HPCD extracts. Hence, SFS is a potential means to simplify the present non-exhaustive hydroxypropyl-beta-cyclodextrin (HPCD)-based extraction technique for the evaluation of PAH bioavailability in soil.     

Seasonal variations and trends in concentrations of filter-collected polycyclic aromatic hydrocarbons (PAH) and mutagenic activity in the San Francisco Bay area

Air monitoring in the San Francisco Bay Area was carried out to measure outdoor community air concentrations of polycyclic aromatic hydrocarbons (PAH) and mutagenic activity (mutagenicity) in particulate organic matter (POM). Monitoring began in 1979 and is currently conducted at six stations. PAH and mutagenicity tests were performed on organic extracts prepared from high volume (hi-vol) filters composited every four months, by meterological season. PAH were determined by high pressure liquid chromatography (HPLC) with fluorescence and ultraviolet detection. Mutagenicity was measured in the Ames Salmonella bioassay using strain TA98 with and without metabolic activation. The nine-year mean concentration of benzo(a)pyrene (BaP) was 0.4 ng/m3. The mutagenicity of this amount of BaP accounted for only about 0.2% of the observed mutagenicity in POM and other measured PAH accounted for even less. Concentrations of PAH and mutagenicity were three to nine times higher during the winter than during other seasons. Year-to-year wintertime trends in several PAH were also seen. Early in the 1980s, winter concentrations of BaP and benzo (g,h,i)perylene increased. However since the mid-1980's, their concentrations have fallen. The decrease in PAH concentrations may be the result of an increasing proportion of vehicles with relatively low organic emissions. In contrast to PAH, mutagenicity did not show significantly year-to-year time trends.     

Simple digestion procedure followed by the azomethine-H method for accurate boron analysis and discrimination between its fractions in wastewater and soils

Excess boron is a growing environmental problem. It often affects agricultural yields, where reuse of wastewater for irrigation is practiced. This problem raises the need for reliable, simple and economical methods to monitor boron concentrations in wastewater and soil extracts. One such method, the commonly used azomethine-H spectrophotometric method, suffers from color interference, originating from high concentrations of dissolved organic matter, when applied to many wastewater and agricultural soil extracts. Moreover, this method only quantifies free dissolved boron and lacks the ability to quantify boron that is adsorbed to either the dissolved organic matter or suspended solids that are present in the sample. This work suggests a modification of the standard azomethine-H method, in which the solution is digested with potassium persulfate prior to the standard procedure. We show that this pretreatment can overcome the color interference and lead to highly accurate and precise boron analyses in wastewater. In soil extracts, the boron concentrations obtained using the suggested procedure were better correlated to inductively coupled plasma (ICP) spectrometry results than those measured by the standard method, because whereas the standard method quantifies the free dissolved boron only, the modified method, like the ICP method, quantifies the total dissolved boron in the sample. Thus, the suggested modification can be used to quantify the respective distributions of free dissolved boron, boron adsorbed to dissolved organic matter and boron adsorbed to suspended solids in soil extracts and water samples.     

A Comparison of Mass,Lead, Sulfate,and Nitrate Concentrations in a Field Study Using Dichotomous,Size-Selective,and Standard Hi-Vol Samplers

Air monitoring In the San Francisco Bay Area was carried out to measure outdoor community air concentrations of poly cyclic aromatic hydrocarbons (PAH) and mutagenlc activity (mutagenlclty) In participate organic matter (POM). Monitoring began In 1979 and Is currently conducted at six stations. PAH and mutagenlclty tests were performed on organic extracts prepared from high volume (hl-vol) filters composited every four months, by meteorological season. PAH were determined by high pressure liquid chromatography (HPLC) with fluorescence and ultraviolet detection. Mutagenlclty was measured In the Ames Salmonella bloas-say using strain TA98 with and without metabolic activation. The nine-year mean concentration of benzo(a)pyrene (BaP) was 0.4 ng/m³. The mutagenlcfty of this amount of BaP accounted for only about 0.2% of the observed mutagenicity In POM and other measured PAH accounted for even less. Concentrations of PAH and mutagenlclty were three to nine times higher during the winter than during other seasons. Year-to-year wintertime trends In several PAH were also seen. Early In the 1980s, winter concentrations of BaP and benzo (g,h,i)perylene Increased. However since the mld-1980’s, their concentrations have fallen. The decrease In PAH concentrations may be the result of an Increasing proportion of vehicles with relatively low organic emissions. In contrast to PAH, mutagenlcfty did not show significant year-to-year time trends.     

DNA damage and repair process in earthworm after in-vivo and in vitro exposure to soils irrigated by wastewaters

In this study, DNA damage to earthworms (Eisenia fetida) after in vivo exposure to contaminated soils was measured by detecting DNA strand breakages (DSBs) and causality was analyzed through fractionation based bioassays. A non-linear dose-response relationship existed between DNA damage and total soil PAHs levels. DNA damage, measured with the comet assay, and its repair process, were observed. To identify the chemical causality, an in vitro comet assay using coelomocytes was subsequently performed on the fractionated organic extracts from soils. The results showed that the PAHs in the soils were responsible for the exerting genotoxic effects on earthworms. When normalized to benzo(a)pyrene toxic equivalent (TEQ(BaP)), the saturation dose in the dose-response curve was about 10ng TEQ(BaP) g(-1) soil (dw).     

Comparison of in-house-developed ELISA with HPLC techniques for the analysis of atrazine residues

In-house developed ELISA was standardized to monitor atrazine residues in different environmental samples. The standard curve was linear, indicating an increase in log concentration with decrease in absorbance (%B/B(0)=1.075-0.042 Log C; r= -0.966). The middle of the test was at 75 ng/L and the lowest detection limit at 4 ng/L. ELISA significantly correlated with the high performance liquid chromatography (HPLC) (r=0.990). Internal validation showed good accuracy and precision. Maximum atrazine residues were present in Jehlum River water/sediments and maize/sugarcane plant roots. Most of the food samples were found to be contaminated. ELISA required less clean-up steps than HPLC, but showed matrix effect in soil/colored extracts.     

Comparison of in-house-developed ELISA with HPLC techniques for the analysis of atrazine residues

In-house developed ELISA was standardized to monitor atrazine residues in different environmental samples. The standard curve was linear, indicating an increase in log concentration with decrease in absorbance (%B/B₀ = 1.075–0.042 Log C; r = ?0.966). The middle of the test was at 75 ng/L and the lowest detection limit at 4 ng/L. ELISA significantly correlated with the high performance liquid chromatography (HPLC) (r = 0.990). Internal validation showed good accuracy and precision. Maximum atrazine residues were present in Jehlum River water/sediments and maize/sugarcane plant roots. Most of the food samples were found to be contaminated. ELISA required less clean-up steps than HPLC, but showed matrix effect in soil/colored extracts.     

Method development for determination of fluroxypyr in soil

Four methods were developed for the analysis of fluroxypyr in soil samples from oil palm plantations. The first method involved the extraction of the herbicide with 0.05 M NaOH in methanol followed by purification using acid base partition. The concentrated material was subjected to derivatization and then cleaning process using a florisil column and finally analyzed by gas chromatography (GC) equipped with electron capture detector (ECD). By this method, the recovery of fluroxypyr from the spiked soil ranged from 70 to 104% with the minimum detection limit at 5 microg/kg. The second method involved solid liquid extraction of fluroxypyr using a horizontal shaker followed by quantification using high performance liquid chromatography (HPLC) equipped with UV detector. The recovery of fluroxypyr using this method, ranged from 80 to 120% when the soil was spiked with fluroxypyr at 0.1-0.2 microg/g soil. In the third method, the recovery of fluroxypyr was determined by solid liquid extraction using an ultrasonic bath. The recovery of fluroxypyr at spiking levels of 4-50 microg/L ranged from 88 to 98% with relative standard deviations of 3.0-5.8% with a minimum detection limit of 4 microg/kg. In the fourth method, fluroxypyr was extracted using the solid liquid extraction method followed by the cleaning up step with OASIS HLB (polyvinyl dibenzene). The recovery of fluroxypyr was between 91 and 95% with relative standard deviations of 4.2-6.2%, respectively. The limit of detection in method 4 was further improved to 1 pg/kg. When the weight of soil used was increased 4 fold, the recovery of fluroxypyr at spiking level of 1-50 microg/kg ranged from 82-107% with relative standard deviations of 0.5-4.7%.     

Benzo[a]pyrene removal from soil by Phanerochaete chrysosporium grown on sugarcane bagasse and pine sawdust

The capacity of Phanerochaete chrysosporium grown on soil with added sugarcane baggase (BP) and pine sawdust (PS) to remove benzo(a)pyrene (BaP) was studied. A half factorial two-level experiment 2(4-1) was designed to determine the effect of: type of lignocellulosic material (BP and PS) for fungus growth, age of fungus (5 and 10d), amount of lignocellulosic material (10% and 15% w/w) and soil moisture content (water holding capacity of 45% and 56% w/w). Inoculum obtained at different ages showed that the capacity of P. chrysosporium to remove BaP depends on the lignocellulosic used and on inoculum age. Abiotic BaP removal was affected significantly (p<0.05) by inoculum age, type of lignocellulosic added and soil moisture content. The removal of BaP by lignocellulosic material was more effective by young inocula (71.97 mg BaP kg(-1) dry soil), with high percentage of added lignocellulosic (71.57 mg BaP kg(-1) dry soil) and at low soil moisture content (73.07 mg BaP kg(-1) dry soil). When fungus was grown on BP, maximum BaP removal rate was obtained at 5d of incubation (10.85 mg BaP d(-1)l(-1) and 50.12 mg BaP kg(-1) dry soil), while in PS maximum BaP removal was obtained at 10d of incubation (12.06 mg BaP d(-1)l(-1) and 39.94 mg BaP kg(-1) dry soil).     

Application of ultrasonic assisted extraction of chemically diverse organic compounds from soils and sediments

The objective of this research was the development, optimization, and demonstration of an ultrasonic assisted extraction (UAE) based method for organic anthropogenic waste indicators (AWIs) with a range of physicochemical properties from soil and sediment samples. The optimized method was designed to be cost effective compared to existing extraction methods, which may require large quantities of consumables, produce substantial volumes of organic waste, or require costly instrumentation or equipment. Reagent grade sand, soil collected from the native grassland in proximity to Eastern Washington University (EWU), and sediment samples collected from the Spokane river were used as sample matrices during method development. These matrices were fortified with eight AWIs of varying chemical properties that are representative of a variety of household, industrial, and agricultural sources. The recoveries of the AWIs spiked onto these matrices were determined in the extracts using gas chromatography/mass spectrometry (GC/MS). These values reflect the efficiency of the method for extraction of these analytes from representative environmental matrices. Recoveries ranged from 46.1% to 110% in the fortified soil and from 49.2% to 118.6% in the fortified sediment samples, which is comparable with existing methods for the study analytes. The optimized method was then used to quantify AWIs in a biosolid-amended soil. Indole and p-cresol were detected in the biosolid-amended soil.     

Potential use of DNA adducts to detect mutagenic compounds in soil

In this study, three different soils with contrasting features, spiked with 300 mg benzo[a]pyrene (BaP)/kg dry soil, were incubated at 20 °C and 60% water holding capacity for 540 days. At different time points, BaP and DNA were extracted and quantified, and DNA adducts were quantified by ³²P-postlabelling. After 540 days incubation, 69.3, 81.6 and 83.2% of initial BaP added remained in Cruden Bay, Boyndie and Insch soils, respectively. Meanwhile, a significantly different amount of DNA-BaP adducts were found in the three soils exposed to BaP over time. The work demonstrates the concept that DNA adducts can be detected on DNA extracted from soil. Results suggest the technique is not able to directly reflect bioavailability of BaP transformation products. However, this new method provides a potential way to detect mutagenic compounds in contaminated soil and to assess the outcomes of soil remediation.     

An evaluation of two fluorescence screening methods for the determination of chrysene metabolites in fish bile

Two screening methods, synchronous fluorescence spectrometry (SFS) and high performance liquid chromatography with fluorescence detection (HPLC-F), have been evaluated for their suitability in determining chrysene metabolites in fish bile. The optimal wavelength pair, excitation/emission 272/374 nm, for SFS measurements of chrysene metabolites was identified by analysis of bile taken from fish exposed to the pure compound. This analysis revealed in addition some information about the metabolite pattern. However, when bile from fish exposed to complex and environmentally relevant mixtures of polycyclic aromatic hydrocarbons (PAHs) was analysed using these methods, identification of the chrysene metabolites was poor. Analysis of bile taken from fish exposed to single PAHs identified other three- and four-ring aromatics as the main interfering compounds. Both methods were equally able to discriminate between impacted and reference sites by determination of relative concentrations of fluorescent three- and four-ring aromatics.     

Method Development for Determination of Fluroxypyr in Soil

Abstract

Four methods were developed for the analysis of fluroxypyr in soil samples from oil palm plantations. The first method involved the extraction of the herbicide with 0.05 M NaOH in methanol followed by purification using acid base partition. The concentrated material was subjected to derivatization and then cleaning process using a florisil column and finally analyzed by gas chromatography (GC) equipped with electron capture detector (ECD). By this method, the recovery of fluroxypyr from the spiked soil ranged from 70 to 104% with the minimum detection limit at 5 µg/kg. The second method involved solid liquid extraction of fluroxypyr using a horizontal shaker followed by quantification using high performance liquid chromatography (HPLC) equipped with UV detector. The recovery of fluroxypyr using this method, ranged from 80 to 120% when the soil was spiked with fluroxypyr at 0.1–0.2 µg/g soil. In the third method, the recovery of fluroxypyr was determined by solid liquid extraction using an ultrasonic bath. The recovery of fluroxypyr at spiking levels of 4–50 µg/L ranged from 88 to 98% with relative standard deviations of 3.0–5.8% with a minimum detection limit of 4 µg/kg. In the fourth method, fluroxypyr was extracted using the solid liquid extraction method followed by the cleaning up step with OASIS® HLB (polyvinyl dibenzene). The recovery of fluroxypyr was between 91 and 95% with relative standard deviations of 4.2–6.2%, respectively. The limit of detection in method 4 was further improved to 1 µg/kg. When the weight of soil used was increased 4 fold, the recovery of fluroxypyr at spiking level of 1–50 µg/kg ranged from 82–107% with relative standard deviations of 0.5–4.7%.     

Determination of sulfosulfuron residues in soil under wheat crop by a novel and cost-effective method and evaluation of its carryover effect

A novel and cost-effective method of sulfosulfuron extraction has been developed using distilled water as an extraction solvent. Using this method, the environmental fate of sulfosulfuron was investigated in soil under wheat crop. Studies were conducted under natural field conditions in randomized block design and herbicide (75% water dispersible granules (WG)) was applied after 24 days of sowing. The rates of applications were 25 and 50 g of active ingredient (a.i.) per hectare. Soil samples were collected at predetermined intervals and analyzed by high performance liquid chromatography (HPLC). The minimum detection limit was found to be 0.001 micro g g(-1). The dissipation of sulfosulfuron followed first-order rate kinetics and dissipated with a half-life of 5.4-6.3 days. After harvest, field soil was used for conducting a pot experiment with bottle gourd (Lagenaria siceraria) as test plants to study the carry over effect of sulfosulfuron. No phytotoxicity was observed to bottle gourd in pot experiment with harvest soil.     

Effects of riboflavin on the phototransformation of benzo[a]pyrene

Riboflavin (Vitamin B2) is a natural dye-sensitizer habitually present in natural waters. Effects of riboflavin as photosensitizer on the transformation of benzo[a]pyrene (BaP) (10 microM) in the aqueous-organic solvent (water/acetonitrile/methanol 50/40/10) were investigated in this study. The photolysis half life of BaP in solution containing 50 microM riboflavin was 5 min, compared to 98 min in the absence of riboflavin. The rate of phototransformation of BaP increased as the concentration of riboflavin was raised from 10 microM to 100 microM under both natural sunlight and UVA irradiation. The half life of BaP in the presence of 50 microM riboflavin was 10.6 min and 43.1 min when exposed to visible range of natural sunlight and UVA irradiation respectively. Riboflavin decomposes under natural sunlight. Lumichrome, a principal photoproduct of riboflavin, was shown to photosensitize BaP under natural sunlight after photolysis of riboflavin. Our study indicated that other photoproducts from riboflavin, such as lumiflavin, were also involved in the phototransformation of BaP under sunlight when riboflavin diminished. The major photoproducts in the photolysis of BaP were identified as 1,6-benzo[a]pyrene-dione, 3,6-benzo[a]pyrene-dione, 6,12-benzo[a]pyrene-dione by using high performance liquid chromatography (HPLC). All these products were detected in the samples which were irradiated under different light sources and in the presence or absence of riboflavin. The possible phototransformation mechanism was discussed.     

Microtox testing of pentachlorophenol in soil extracts and quantification by capillary electrochromatography (CEC)--a rapid screening approach for contaminated land

An approach to rapid soil testing which involved the use of simple solvent extraction methods was developed. The analytes of interest were priority pollutants of low water solubility which could not be readily removed from the soil using water. Direct toxicity testing of the soil samples by Microtox showed a high background toxicity which prevented realistic toxicity data from being obtained for the contaminants present. A range of different extraction solutions was used in an attempt to extract the contaminants while eliminating the matrix effects of the soil. It was necessary that the solvents selected for extraction of the soil samples were not of significant toxicity, as this could potentially mask the toxic effects of any compounds extracted from the soil. The extraction efficiencies of solvent systems were evaluated using pentachlorophenol (PCP) as a model compound of known toxicity in the Microtox assay. A rapid and cost-effective method was developed in order to determine the amount of PCP recovered from the soil by the extraction solvents employed. This method consisted of a solid phase extraction (SPE) step followed by quantification using capillary electrochromatography (CEC). Recoveries were greater when a higher proportion of organic solvent (methanol) was used in the extraction process, and lowest when water was used. An extraction based on water could provide information on the potential for leaching of contaminants from the soil into nearby water bodies in an environmental setting. An organic solvent extraction method could indicate how much toxicity soil-dependent organisms might be exposed to through ingestion. Extraction based on 50% (v/v) methanol in water was considered to be the most suitable overall extraction solution for soil screening, given that this permitted extraction of the water-insoluble compound PCP at a level which was clearly toxic in the Microtox assay while also retaining the capability to extract water-soluble contaminants.     

Dissipation of available benzo[a]pyrene in aging soil co-contaminated with cadmium and pyrene

A microcosm experiment was conducted to investigate the dissipation of available benzo[a]pyrene (BaP) in soils co-contaminated with cadmium (Cd) and pyrene (PYR) during aging process. The available residue of BaP in soil was separated into desorbing and non-desorbing fractions. The desorbing fraction contributed more to the dissipation of available BaP than the non-desorbing fraction did. The concentration of bound-residue fraction of BaP was quite low across all treatments. Within the duration of this study (250 days), transformation of BaP from available fractions to bound-residue fraction was not observed. Microbial degradation was the dominant mechanism of the dissipation of available BaP in the soil. The dissipation of available BaP was significantly inhibited with the increment in Cd level in the soil. The addition of PYR (250 mg kg^?1) remarkably promoted the dissipation of available BaP without reducing Cd availability in the soil. The calculated half-life of available BaP in the soil prolonged with the increment in Cd level; however, the addition of PYR shortened the half-life of available BaP by 13.1, 12.7, and 32.8 % in 0.44, 2.56, and 22 mg Cd kg^?1 soils, respectively. These results demonstrated that the inhibiting effect of Cd and the promoting effect of PYR on the dissipation of available BaP were competitive. Therefore, this study shows that the bioremediation process of BaP can be more complicated in co-contaminated soils.     

Determination of sulfosulfuron residues in soil under wheat crop by a novel and cost-effective method and evaluation of its carryover effect

A novel and cost-effective method of sulfosulfuron extraction has been developed using distilled water as an extraction solvent. Using this method, the environmental fate of sulfosulfuron was investigated in soil under wheat crop. Studies were conducted under natural field conditions in randomized block design and herbicide (75% water dispersible granules (WG)) was applied after 24 days of sowing. The rates of applications were 25 and 50 g of active ingredient (a.i.) per hectare. Soil samples were collected at predetermined intervals and analyzed by high performance liquid chromatography (HPLC). The minimum detection limit was found to be 0.001 μ g g^{? 1}. The dissipation of sulfosulfuron followed first-order rate kinetics and dissipated with a half-life of 5.4–6.3 days. After harvest, field soil was used for conducting a pot experiment with bottle gourd (Lagenaria siceraria) as test plants to study the carry over effect of sulfosulfuron. No phytotoxicity was observed to bottle gourd in pot experiment with harvest soil.     

Enhanced degradation of benzo[a]pyrene by Mycobacterium sp. in conjunction with green alga

Previous work in this laboratory has confirmed that the bacteria Mycobacterium sp. strain RJGII.135 and Sphingomonas yanoikuyae strain B1 and the green alga Selanastrum capricornutum strain UTEX 1648 degrade benzo[a]pyrene (BaP) to various BaP intermediates. S. capricornutum was first grown with BaP for 4 days. The organic extract of this media was then introduced into separate cultures of strain RJGII.135 and strain B1; separate cultures were grown with BaP for comparison. Cultures grown with BaP and those grown with the algal/BaP extract showed similar mineralization patterns. The quantity of total metabolites formed was greater in bacterial cultures grown with the algal/BaP extract than those grown with BaP alone. For strain RJGII.135, only 27% of the original BaP remained in cultures grown with the algal/BaP extract; 59% remained in cultures grown with BaP. For strain B1, only 6% of the original BaP remained in cultures grown with the algal/BaP extract; 38% remained in cultures grown with BaP. These results indicate that strategies utilizing organisms together may be necessary in being able to degrade large, recalcitrant polycyclic aromatic hydrocarbons (PAHs) such as BaP.     

Comparison of dioxin and furan TEQ determination in contaminated soil using chemical,micro-EROD,and immunoassay analysis

High resolution mass spectrometry gas chromatography (GC/MS) is the standard method for dioxin and furan analysis in environmental matrices. Considered as very accurate, this method is however time consuming and expensive. Methods based on biological interactions have the necessary sensitivity but began only recently to be investigated in the context of environmental applications. We have compared dioxin and furan toxicity levels (expressed as toxic equivalent quantities (TEQs)) in soil samples by three analytical approaches: the micro-ethoxyresorufin-o-deethylase (EROD) bioassay (a receptor-based method), an immunoassay (antibody-based method) and GC/MS analysis (used as a reference) using a shortened extraction-purification method. Both biological methods were sensitive to interferences from compounds co-extracted from samples. Most samples were underestimated by the immunoassay and, at a greater extent, overestimated by the EROD bioassay. The average accuracy of TEQ estimation (86 +/- 45% of values established by GC/MS) and the absence of false-negatives showed by the immunoassay suggest the usefulness of this method for semi-quantitative, preliminary characterization of potentially contaminated sites.