High-performance for hydrogen evolution and pollutant degradation of reduced graphene oxide/two-phase g-C<Subscript>3</Subscript>N<Subscript>4</Subscript> heterojunction photocatalysts

We have successfully synthesized the composites of two-phase g-C₃N₄ heterojunction photocatalysts by one-step method. And the reduced graphene oxide/two-phase g-C₃N₄ heterojunction photocatalyst was fabricated via a facile hydrothermal reduction method. The characterization results indicated that the two-phase g-C₃N₄ was integrated closely, and the common phenomenon of agglomeration for g-C₃N₄ was significantly reduced. Moreover, the oxidized graphene was reduced successfully in the composites and the graphene was overlaid on the surface or the interlayers of g-C₃N₄ heterojunction composite uniformly. In addition, we have carried out the photocatalytic activity experiments by H₂ evolution and rhodamine B removal, tetracycline removal under the visible light irradiation. The results revealed that the composite has improved the separation efficiency a lot than the pure photocatalyst. The photocurrent test demonstrated that the recombination of electrons and holes were efficiently inhibited as well as enhanced the photocatalytic activity. The 0.4% rGO loaded samples, 0.4% rGOCN2, own the best performance. Its rate of H₂ evolution was 15 times as high as that of the pure g-C₃N₄.     

Photocatalytic decomposition of methanol over La/TiO<Subscript>2</Subscript> materials

Lanthanum-modified TiO₂ photocatalysts (0.2–1.5 wt% La) were investigated in the methanol decomposition in an aqueous solution. The photocatalysts were prepared by the common sol-gel method followed by calcination. The structural (X-ray diffraction, Raman, X-ray photoelectron spectroscopy), textural (N₂ physisorption), and optical properties (diffuse reflectance spectroscopy, photoelectrochemical measurements) of all synthetized nanomaterials were correlated with photocatalytic activity. Both pure TiO₂ and La-doped TiO₂ photocatalysts proved higher yields of hydrogen in comparison to photolysis. The photocatalyst with optimal amount of lanthanum (0.2 wt% La) showed almost two times higher amount of hydrogen produced at the same time as in the presence of pure TiO₂. The photocatalytic activity increased with both increasing photocurrent response and decreasing amount of lattice and surface O species. It has been shown that both direct and indirect mechanisms of methanol photocatalytic oxidation participate in the production of hydrogen. Both direct and indirect mechanisms take part in the formation of hydrogen.     

Photocatalytic decomposition of N<Subscript>2</Subscript>O over g-C<Subscript>3</Subscript>N<Subscript>4</Subscript>/WO<Subscript>3</Subscript> photocatalysts

Although the nitrous oxide belongs among three of the most contributing greenhouse gases to global warming, it is quite neglected by photocatalytic society. The g-C₃N₄ and WO₃ composites were therefore tested for the photocatalytic decomposition of N₂O for the first time. The pure photocatalysts were prepared by simple calcination of precursors, and the composites were prepared by mixing of suspension of pure components in water followed by calcination. The structural (X-ray diffraction, X-ray photoelectron spectroscopy, high-resolution transmission electron microscopy), textural (N₂ physisorption), and optical properties (diffuse reflectance spectroscopy, photoluminescence spectroscopy, photoelectrochemical measurements) of all composites were correlated with photocatalytic activity. The experimental results and results from characterization techniques confirmed creation of Z-scheme in the WO₃/g-C₃N₄ composites, which was confirmed by hydroxyl radicals’ trapping measurements. The photocatalytic decomposition of N₂O was carried out in the presence of UVA light (peak intensity at 365 nm) and the 1:2 WO₃/g-C₃N₄ composite was the most active one, but the photocatalytic activity was just negligibly higher than that of pure WO₃. This is caused by relatively weak interaction between WO₃ and g-C₃N₄ which was revealed from XPS.     

Photocatalytic reduction of carbon dioxide over Cu/TiO<Subscript>2</Subscript> photocatalysts

The photocatalytic reduction of CO₂ with H₂O was investigated using Cu/TiO₂ photocatalysts in aqueous solution. For this purpose, Cu/TiO₂ photocatalysts (with 0.2, 0.9, 2, 4, and 6 wt.% of Cu) have been synthesized via sol-gel method. The photocatalysts were extensively characterized by means of inductively coupled plasma optical emission spectrometry (ICP-OES), N₂ physisorption (BET), XRD, UV-vis DRS, FT-IR, Raman spectroscopy, TEM-EDX, and photoelectrochemical measurements. The as-prepared photocatalysts contain anatase as a major crystalline phase with a crystallite size around 13 nm. By increasing the amount of Cu, specific surface area and band gap energy decreased in addition to the formation of large agglomeration of CuO. Results revealed that the photocatalytic reduction of CO₂ decreased in the presence of Cu/TiO₂ in comparison to pure TiO₂, which might be associated to the formation of CuO phase acting as a recombination center of generated electron-hole pair. Decreasing of photoactivity can also be connected with a very low position of conduction band of photocatalysts with high Cu content, which makes H₂ production necessary for CO₂ reduction more difficult.     

纳米Bi2O3/TiO2复合光催化剂的制备及性能研究

以光催化效果为评价标准，采用超声波作用下水解法制备Bi₂O₃/TiO₂复合光催化剂，考察了水解条件和Bi₂O₃掺入量等制备条件对复合光催化剂性能的影响。结果表明，与传统制备方法相比，该方法操作简单、快速；当水和乙醇的比例为4∶1时所得样品的光催化活性最好；Bi₂O₃的掺入拓宽了TiO₂对光的吸收范围，提高了TiO₂的光催化活性，掺入量(Bi₂O₃)为0.25%复合光催化剂催化活性最高；复合光催化剂对多种水溶性染料均具有较好的处理效果。     

Enhanced photocatalytic activity using GO/TiO<Subscript>2</Subscript> catalyst for the removal of DCA solutions

This work aimed to optimize high-performance photocatalysts based on graphene oxide/titanium dioxide (GO/TiO₂) nanocomposites for the effective degradation of aqueous pollutants. The catalytic activity was tested against the degradation of dichloroacetic acid (DCA), a by-product of disinfection processes that is present in many industrial wastewaters and effluents. GO/TiO₂ photocatalysts were prepared using three different methods, hydrothermal, solvothermal, and mechanical, and varying the GO/TiO₂ ratio in the range of 1 to 10%. Several techniques were applied to characterize the catalysts, and better coupling of GO and TiO₂ was observed in the thermally synthesized composites. Although the results obtained for DCA degradation showed a coupled influence of the composite preparation method and its composition, promising results were obtained with the photocatalysts compared to the limited activity of conventional TiO₂. In the best case, corresponding to the composite synthesized via hydrothermal method with 5% of GO/TiO₂ weight ratio, an enhancement of 2.5 times of the photocatalytic degradation yield of DCA was obtained compared to bare TiO₂, thus opening more efficient ways to promote the application of photocatalytic remediation technologies.     

Removal of AOX, total nitrogen and chlorinated lignin from bleached Kraft mill effluents by UV oxidation in the presence of hydrogen peroxide utilizing TiO2 as photocatalyst

Background, aim, and scope  The pulp and paper industry is the sixth largest polluter discharging a variety of gaseous, liquid, and solid wastes into the environment. Effluents from bleached Kraft mill effluents (BKME) are polluting waters to a great extent These effluents cause considerable damage to the receiving waters if discharged untreated since they have high levels of biological oxygen demand (BOD), chemical oxygen demand (COD), chlorinated compounds (measured as AOX), suspended solids (mainly fibers), fatty acids, tannins, resin acids, lignin and its derivatives, sulfur and sulfur compounds, etc. This study aimed to remove adsorbed organic halogen (AOX), total nitrogen, and lignin-degrading products in the wastewater (4,500 m³/h) from the paper mill in the pulp and paper industry, which is discharged to sea from a plant located in western Turkey. Materials and methods  The photocatalytic degradation of AOX, total nitrogen, and chlorinated lignin in BKME have been investigated in different parameters, such as time, H₂O₂ and TiO₂ concentration. In addition, for investigating the effect of chlorine on the removal of lignin, pure lignin solution was prepared in equal amounts to chlorinated lignin degradation products found in BKME. The same experiments were conducted for this solution. Experiments were carried out in photocatalytic reactor made of Pyrex glass. The mercury lamp was used as a radiation source. All irradiation was carried out under constant stirring. The existence of dissolved O₂ is an important factor which increases the photocatalytic degradation. Hence, we used an air pump for the aeration of the wastewater solutions. The temperature of the wastewater was controlled and adjusted to 25°C by thermostat pump in conjunction with a cooler. At the end of all experiments, AOX, total nitrogen and lignin concentrations were analyzed according to standard methods. All experiments were performed in duplicate and average values were used. Results and discussion  When the effect of H₂O₂ and time were investigated, it was observed that the AOX concentration increased from 3.0 to 11.0 mg/L by only UV. However, when H₂O₂ was added, AOX concentration decreased from approximately 3.0 to 0.0 mg/L. The optimal conditions for the removal of AOX appear to be an initial H₂O₂ concentration of 20.0 mL/L and reaction time of 50 min. In addition, at the same experiment conditions, it was seen that the total nitrogen concentration decreased from 23.0 to 15.0 mg/L by only UV and by increasing H₂O₂ concentration, the concentration of 20.0 mL/L H₂O₂ appears to be optimal (9.0 mg/L). The AOX, total nitrogen and lignin degradation products and pure lignin go through a minimum when the concentration of H₂O₂ and TiO₂ increases at constant pH and UV intensity. The kinetics for the degradation of AOX, total nitrogen and lignin degradation products followed a pseudo-first order law with respect to the products, and the degradation rates (min⁻¹) for the UV/TiO₂/H₂O₂ system were higher than that of the corresponding values for the UV/H₂O₂ system. Conclusions  The AOX, total nitrogen and lignin concentration go through a minimum when the concentration of H₂O₂ and TiO₂ increases at constant pH and UV intensity. It was found that the UV/TiO₂/H₂O₂ system has proved capable of the degradation of total nitrogen as well as chlorinated and degraded lignin in BKME. Recommendations and perspectives  The photocatalytic process can be considered a suitable alternative for the remove of some compounds from the BKME. Nevertheless, further studies should be carried out to confirm the practical feasibility of BKME. Another result obtained from the study is that pre-purification carried out with UV/TiO₂/H₂O₂ photocatalytic process may constitute an important step for further purification processes such as adsorption, membrane processes, etc.     

天然沸石负载La2O3-ZnO-TiO2光催化降解活性艳红K-2BP

利用80目天然斜发沸石作载体制备La₂O₃(0.5%)-ZnO(20%)-TiO₂/沸石复合光催化剂，以20 W紫外灯为光源，在自制的光催化反应器中降解活性艳红K-2BP，考察了光照时间、空气通入量、催化剂用量、溶液初始浓度、H₂O₂与Fe³⁺投加量等对活性艳红K-2BP光催化降解率的影响。结果表明，当溶液初始浓度为60 mg/L，催化剂投加量为12 g/L，通气量为1 200 mL/min，光照2.5 h，活性艳红K-2BP的降解率可达99.2%；H₂O₂和Fe³⁺投加量为4 mL/L和3 g/L时，光照1 h活性艳红K-2BP降解率分别为100%和97.2%。紫外可见吸收光谱显示，LZTZ光催化剂可有效降解印染废水。     

Use of carbon-based composites to enhance performance of TiO<Subscript>2</Subscript> for the simultaneous removal of nitrates and organics from aqueous environments

The simultaneous photocatalytic removal of nitrate from aqueous environment in presence of organic hole scavenger using TiO₂ has long been explored. However, the use of unmodified TiO₂ in such reaction resulted in non-performance or release of significant amount of undesirable reaction products in the process, a problem that triggered surface modification of TiO₂ for enhanced photocatalytic performance. Previous studies focused on decreasing rate of charge carrier recombination and absorption of light in the visible region. Yet, increasing active sites and adsorption capacity by combining TiO₂ with a high surface area adsorbent such as activated carbon (AC) remains unexploited. This study reports the potential of such modification in simultaneous removal of nitrates and oxalic acid in aqueous environment. The adsorptive behaviour of nitrate and oxalic acid on TiO₂ and TiO₂/AC composites were studied. The Langmuir adsorption coefficient for nitrate was four times greater than that of oxalic acid. However, the amount of oxalic acid adsorbed was about 10 times greater than the amount of nitrate taken up. Despite this advantage, the materials did not appear to produce more active photocatalysts for the simultaneous degradation of nitrate and oxalic acid. The photocatalytic activity of TiO₂ and its carbon-based composites was improved by combination with Cu₂O particles. Consequently, 2.5 Cu₂O/TiO₂ exhibited the maximum photocatalytic performance with 57.6 and 99.8% removal of nitrate and oxalic acid, respectively, while selectivity stood at 45.7, 12.4 and 41.9% for NH₄⁺, NO₂^? and N₂, respectively. For the carbon based, 2.5 Cu₂O/TiO₂-20AC showed removal of 12.7% nitrate and 80.3% oxalic acid and achieved 21.6, 0 and 78.4% selectivity for NH₄⁺, NO₂^? and N₂, respectively. Using the optimal AC loading (20 wt%) resulted in significant decrease in the selectivity for NH₄⁺ with no formation of NO₂^?, which unveils that selectivity for N₂ and low/no selectivity for undesirable products can be manipulated by controlling the rate of consumption of oxalic acid. In contract, no nitrate reduction was observed with Cu₂O promoted TiO₂-T and its TiO₂-(T)-20AC, which may be connected to amorphous nature of TiO₂-T and perhaps served as charge carrier trapping sites that impeded activity.     

Study on the removal of elemental mercury from simulated flue gas by Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>-CeO<Subscript>2</Subscript>/AC at low temperature

Fe₂O₃ and CeO₂ modified activated coke (AC) synthesized by the equivalent-volume impregnation were employed to remove elemental mercury (Hg⁰) from simulated flue gas at a low temperature. Effects of the mass ratio of Fe₂O₃ and CeO₂, reaction temperature, and individual flue gas components including O₂, NO, SO₂, and H₂O (g) on Hg⁰ removal efficiency of impregnated AC were investigated. The samples were characterized by Brunauer–Emmett–Teller (BET), X-ray diffraction (XRD), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS). Results showed that with optimal mass percentage of 3 % Fe₂O₃ and 3 % CeO₂ on Fe3Ce3/AC, the Hg⁰ removal efficiency could reach an average of 88.29 % at 110 °C. Besides, it was observed that O₂ and NO exhibited a promotional effect on Hg⁰ removal, H₂O (g) exerted a suppressive effect, and SO₂ showed an insignificant inhibition without O₂ to some extent. The analysis of XPS indicated that the main species of mercury on used Fe3Ce3/AC was HgO, which implied that adsorption and catalytic oxidation were both included in Hg⁰ removal. Furthermore, the lattice oxygen, chemisorbed oxygen, and/or weakly bonded oxygen species made a contribution to Hg⁰ oxidation.     

Adsorptive removal and photocatalytic decomposition of sulfamethazine in secondary effluent using TiO2–zeolite composites

We investigated the adsorption and decomposition of sulfamethazine (SMT), which is used as a synthetic antibacterial agent and discharged into environmental water, using high-silica Y-type zeolite (HSZ-385), titanium dioxide (TiO₂), and TiO₂–zeolite composites. By using ultrapure water and secondary effluent as solvents, we prepared SMT solutions (10 μg/L and 10 mg/L) and used them for adsorption and photocatalytic decomposition experiments. When HSZ-385 was used as an adsorbent, rapid adsorption of SMT in the secondary effluent was confirmed, and the adsorption reached equilibrium within 10 min. The photocatalytic decomposition rate using TiO₂ in the secondary effluent was lower than that in ultrapure water, and we clarified the inhibitory effect of ions and organic matter contained in the secondary effluent on the reaction. We synthesized TiO₂–zeolite composites and applied them to the removal of SMT. During the treatment of 10 μg/L SMT in the secondary effluent using the composites, 76 % and more than 99 % of the SMT were decomposed within 2 and 4 h by photocatalysis. The SMT was selectively adsorbed onto high-silica Y-type zeolite in the composites. Resultantly, the inhibitory effect of the coexisting materials was reduced, and the composites could remove SMT more effectively compared with TiO₂ alone in the secondary effluent.     

Visible-light-induced photocatalytic reduction of Cr(VI) with coupled Bi2O3/TiO2 photocatalyst and the synergistic bisphenol A oxidation

Coupled Bi₂O₃/TiO₂ photocatalysts were fabricated by sol–gel and hydrothermal methods and characterized using various spectroscopy techniques. Photocatalytic reduction of Cr(VI) in aqueous solution, together with the synergistic effect of photodegradation of bisphenol A (BPA), was investigated using these coupled Bi₂O₃/TiO₂ under visible-light irradiation. Coupling of Bi₂O₃ inhibited the phase transformation from anatase to rutile and extended absorption region to visible light. Bi ions did not enter TiO₂ lattice and were more likely to bond with oxygen atoms to form Bi₂O₃ on the surface of TiO₂. Photovoltage signals in visible range revealed the effective interfacial charge transfer between Bi₂O₃ and TiO₂. Two percent Bi₂O₃/TiO₂ exhibited the highest photocatalytic activity of visible-light-induced reduction of Cr(VI). The addition of BPA effectively increased the photocatalytic reduction of Cr(VI). Simultaneously, the presence of Cr(VI) promoted the degradation of BPA, which was demonstrated by the investigation of TOC removal yield and generated intermediates. A possible mechanism of photocatalytic reduction of Cr(VI) and degradation of BPA in Bi₂O₃/TiO₂ system was proposed. The synergistic effect, observed between reduction of Cr(VI) and degradation of BPA, provides beneficial method for environmental remediation and purification of the complex wastewater.     

CuO/TiO2-H2O2可见光催化亚甲基蓝脱色效果及影响因素研究

以水解法制备的锐钛矿型TiO2为载体,制备了CuO/TiO2型光催化剂.以亚甲基蓝为对象,在可见光照射下研究了H2O3加入量、pH值和催化剂投加量对脱色效果的影响,同时与改性前的TiO2催化剂进行了脱色效果的对比.结果表明亚甲基蓝在碱性条件下能较好脱色,H2O2用量和CuO/TiO2催化剂投加量分别为每1 000 mL反应液各加入10 mL和0.1 g时脱色最好;另外,TiO2催化剂也在碱性条件下能较好脱色,H2O2用量和催化剂投加量分别为每1 000 mL反应液各加入12.5 mL和0.1 g时脱色最好.最优条件下对比实验表明,CuO/TiO2型催化剂在可见光照射下具有很高的催化活性,亚甲基蓝2 h脱色率达到88%,远好于改性前的TiO2和Degussa P25催化剂.     

Inactivation of <Emphasis Type="Italic">Escherichia coli</Emphasis> in fresh water with advanced oxidation processes based on the combination of O<Subscript>3</Subscript>, H<Subscript>2</Subscript>O<Subscript>2</Subscript>, and TiO<Subscript>2</Subscript>. Kinetic modeling

The purpose of this work was to study the efficiency of different treatments, based on the combination of O₃, H₂O₂, and TiO₂, on fresh surface water samples fortified with wild strains of Escherichia coli. Moreover, an exhaustive assessment of the influence of the different agents involved in the treatment has been carried out by kinetic modeling of E. coli inactivation results. The treatments studied were (i) ozonation (O₃), (ii) the peroxone system (O₃/0.04 mM H₂O₂), (iii) catalytic ozonation (O₃/1 g/L TiO₂), and (iv) a combined treatment of O₃/1 g/L TiO₂/0.04 mM H₂O₂. It was observed that the peroxone system achieved the highest levels of inactivation of E. coli, around 6.80 log after 10 min of contact time. Catalytic ozonation also obtained high levels of inactivation in a short period of time, reaching 6.22 log in 10 min. Both treatments, the peroxone system (O₃/H₂O₂) and catalytic ozonation (O₃/TiO₂), produced a higher inactivation rate of E. coli than ozonation (4.97 log after 10 min). While the combination of ozone with hydrogen peroxide or titanium dioxide thus produces an increase in the inactivation yield of E. coli regarding ozonation, the O₃/TiO₂/H₂O₂ combination did not enhance the inactivation results. The fitting of experimental values to the corresponding equations through non-linear regression techniques was carried out with Microsoft® Excel GInaFiT software. The inactivation results of E. coli did not respond to linear functions, and it was necessary to use mathematical models able to describe certain deviations in the bacterial inactivation processes. In this case, the inactivation results fit with mathematical models based on the hypothesis that the bacteria population is divided into two different subgroups with different degrees of resistance to treatments, for instance biphasic and biphasic with shoulder models.

Open image in new window

Graphical abstract ?

     

Photodegradation of perfluorooctanoic acid by synthesized TiO2-MWCNT composites under 365nm UV irradiation

Degradation of perfluorooctanoic acid (PFOA) is of great importance due to its global distribution, persistence and toxicity to bioorganisms. In present study, a composite TiO₂ with multiple wall carbon nano-tubes (MWCNTs) was synthesized using sol-gel method and it was used as photocatalyst to degrade PFOA in water. The prepared composite catalyst displayed significant absorption in UV to visible light region. The loading content of TiO₂ on MWCNTs could be adjusted by changing the ratio of precursor to MWCNTs. Due to the combined effect of the adsorption ability and e⁻ transport capacity of MWCNT, the composites displayed much higher photocatalytic ability to PFOA as compared to pure TiO₂ under UV irradiation. The photocatalyst prepared with 10:1 of tetrabutyl titanate/MWCNT was the most effective. With the optimal dosage at 1.6 g L⁻¹, almost 100% of PFOA was degraded in acid medium after irradiation for 8 h. It was proposed that PFOA were mainly degraded by stepwise losing a moiety of CF₂.     

Effect of Nb doping on structural, optical and photocatalytic properties of flame-made TiO2 nanopowder

TiO₂:Nb nanopowders within a dopant concentration in the range of 0.1?C15?at.% were prepared by one-step flame spray synthesis. Effect of niobium doping on structural, optical and photocatalytic properties of titanium dioxide nanopowders was studied. Morphology and structure were investigated by means of Brunauer?CEmmett?CTeller isotherm, X-ray diffraction and transmission electron microscopy. Diffuse reflectance and the resulting band gap energy were determined by diffuse reflectance spectroscopy. Photocatalytic activity of the investigated nanopowders was revised for the photodecomposition of methylene blue (MB), methyl orange (MO) and 4-chlorophenol under UVA and VIS light irradiation. Commercial TiO₂-P25 nanopowder was used as a reference. The specific surface area of the powders was ranging from 42.9?m²/g for TiO₂:0.1?at.% Nb to 90.0?m²/g for TiO₂:15?at.% Nb. TiO₂:Nb particles were nanosized, spherically shaped and polycrystalline. Anatase was the predominant phase in all samples. The anatase-related transition was at 3.31?eV and rutile-related one at 3.14?eV. TiO₂:Nb nanopowders exhibited additional absorption in the visible range. In comparison to TiO₂-P25, improved photocatalytic activity of TiO₂:Nb was observed for the degradation of MB and MO under both UVA and VIS irradiation, where low doping level (Nb?<?1?at.%) was the most effective. Niobium doping affected structural, optical and photocatalytic properties of TiO₂. Low dopant level enhanced photocatalytic performance under UVA and VIS irradiation. Therefore, TiO₂:Nb (Nb?<?1?at.%) can be proposed as an efficient selective solar light photocatalyst.     

H4SiW12O40/TiO2/beads光催化降解亚甲基蓝的研究

以钛酸四丁酯为原料，空心微珠为载体，采用溶胶凝胶法制备TiO₂/beads光催化剂载体，然后浸渍法制备出H₄SiW₁₂O₄₀/TiO₂/beads表面负载修饰型复合光催化剂，并运用SEM、XRD、FT-IR和DRS对催化剂进行表征和分析。研究了H₄SiW₁₂O₄₀/TiO₂/beads对亚甲基蓝降解的光催化活性，考察了光强度、pH值、曝气量、底物浓度和催化剂用量等对催化效率的影响。实验结果表明，在中性条件下，H₄SiW₁₂O₄₀/TiO₂/beads催化剂的投加量为0.25 g/L，浓度为7.5 mg/L的亚甲基蓝溶液在250 W的紫外灯和600 W的可见光灯下光照60 min降解率分别可达到94.5%和55%。     

Photocatalytic degradation of phenol using Ag core-TiO<Subscript>2</Subscript> shell (Ag@TiO<Subscript>2</Subscript>) nanoparticles under UV light irradiation

Ag@TiO₂ nanoparticles were synthesized by one pot synthesis method with postcalcination. These nanoparticles were tested for their photocatalytic efficacies in degradation of phenol both in free and immobilized forms under UV light irradiation through batch experiments. Ag@TiO₂ nanoparticles were found to be the effective photocatalysts for degradation of phenol. The effects of factors such as pH, initial phenol concentration, and catalyst loading on phenol degradation were evaluated, and these factors were found to influence the process efficiency. The optimum values of these factors were determined to maximize the phenol degradation. The efficacy of the nanoparticles immobilized on cellulose acetate film was inferior to that of free nanoparticles in UV photocatalysis due to light penetration problem and diffusional limitations. The performance of fluidized bed photocatalytic reactor operated under batch with recycle mode was evaluated for UV photocatalysis with immobilized Ag@TiO₂ nanoparticles. In the fluidized bed reactor, the percentage degradation of phenol was found to increase with the increase in catalyst loading.     

Photocatalytic degradation of contaminants of concern with composite NF-TiO2 films under visible and solar light

This study reports the synthesis and characterization of composite nitrogen and fluorine co-doped titanium dioxide (NF-TiO₂) for the removal of contaminants of concern in wastewater under visible and solar light. Monodisperse anatase TiO₂ nanoparticles of different sizes and Evonik P25 were assembled to immobilized NF-TiO₂ by direct incorporation into the sol–gel or by the layer-by-layer technique. The composite films were characterized with X-ray diffraction, high-resolution transmission electron microscopy, environmental scanning electron microscopy, and porosimetry analysis. The photocatalytic degradation of atrazine, carbamazepine, and caffeine was evaluated in a synthetic water solution and in an effluent from a hybrid biological concentrator reactor (BCR). Minor aggregation and improved distribution of monodisperse titania particles was obtained with NF-TiO₂-monodisperse (10 and 50 nm) from the layer-by-layer technique than with NF-TiO₂?+?monodisperse TiO₂ (300 nm) directly incorporated into the sol. The photocatalysts synthesized with the layer-by-layer method achieved significantly higher degradation rates in contrast with NF-TiO₂-monodisperse titania (300 nm) and slightly faster values when compared with NF-TiO₂-P25. Using NF-TiO₂ layer-by-layer with monodisperse TiO₂ (50 nm) under solar light irradiation, the respective degradation rates in synthetic water and BCR effluent were 14.6 and 9.5?×?10^?3?min^?1 for caffeine, 12.5 and 9.0?×?10^?3?min^?1 for carbamazepine, and 10.9 and 5.8?×?10^?3?min^?1 for atrazine. These results suggest that the layer-by-layer technique is a promising method for the synthesis of composite TiO₂-based films compared to the direct addition of nanoparticles into the sol.     

Photocatalytic degradation of Reactive Red 195 using anatase/brookite TiO2 mesoporous nanoparticles: Optimization using response surface methodology (RSM) and kinetics studies

In the present study, the photocatalytic degradation of Reactive Red 195 (RR195) from aqueous samples under UV-A irradiation by using anatase/brookite TiO₂ (A/B TiO₂) mesoporous nanoparticles has been investigated. Batch experiments were conducted to study the effects of the main parameters affecting the photocatalytic process. The effects and interactions of most influenced parameters, such as substrate concentration and catalyst load, were evaluated and optimized by using a central composite design model and a response surface methodology. The results indicated that the dye degradation efficiency in the experimental domain investigated was mainly affected by the tested variables, as well as their interaction effects. Analysis of variance showed a high coefficient of determination value (R ²?=?0.9947), thus ensuring a satisfactory adjustment of the first-order regression model (2FI model) with the experimental data. The obtained results also indicate that catalyst loading plays an important role in determining the removal efficiency of RR195 attributable to both photodegradation and adsorption process. Under optimal conditions (initial dye concentration (50 mg/L) and catalyst loading (2,000 mg/L), A/B TiO₂ showed similar removal efficiency compared to that of commercial titania (Degussa P25). Also, at these conditions, complete degradation of RR195 can be achieved by both catalysts within 15 min under UV-A irradiation. The experiments demonstrated that dye removal on the prepared A/B TiO₂ was facilitated by the synergistic effects between adsorption and photocatalysis. Photocatalytic mineralization of RR195 was monitored by total organic carbon. The recycling experiments confirmed the stability of the catalyst.