低浓度硫化氢废气的液相催化氧化法净化实验研究

针对H2S浓度为750~1500mg/m3的气体的液相催化氧化技术进行了动力学实验研究。配制了以铁基离子作为主催化剂的复合吸收净化溶液,同时加入稳定剂和表面活性剂提高催化剂在碱性吸收溶液的活性。分别考察了原料气中H2S、O2含量以及吸收液中催化剂离子浓度、温度等因素对吸收速率的影响;确定了较为理想的吸收操作条件并获得了较好的吸收净化效果;饱和吸收液易于再生,净化性能恢复良好,可重复使用。     

几种金属离子液相催化氧化低浓度H2S实验研究

用液相催化氧化法对低浓度H2S净化进行实验研究.实验结果表明,对H2S浓度在1500-2500mg/m3之间,氧含量为5%的H2S尾气,Fe+、Zn2+和Mn2+在液相中对H2S具有催化氧化作用,其催化性能大小顺序为Fe2+＞Zn2+＞Mn2+,且Fe2+催化性能远远大于其他两种离子;用Fe2+作催化剂,溶液的净化效率可达99%以上,且硫容量也较大,对低浓度H2S的净化相当有利.     

填料塔中Na_2CO_3吸收高浓度H_2S的传质特性

在填料吸收塔中考察了Na2CO3溶液吸收高浓度H2S气体的气液传质特性。通过测量填料塔进出口气体中H2S浓度计算了Na2CO3溶液吸收高浓度H2S气体的总体积传质系数(KGa),并研究了进气流速、吸收液流量、吸收温度和吸收液浓度对KGa的影响。结果表明,KGa随Na2CO3浓度、吸收液流量的增加而增加,随吸收温度、进气流速的升高而降低;在高浓度H2S吸收过程中液相传质阻力不能忽略。     

填料塔中Na2CO3吸收高浓度H2S的传质特性

在填料吸收塔中考察了Na2CO3溶液吸收高浓度H2S气体的气液传质特性。通过测量填料塔进出口气体中H2S浓度计算了Na2CO3溶液吸收高浓度H2S气体的总体积传质系数（KGa），并研究了进气流速、吸收液流量、吸收温度和吸收液浓度对KGa的影响。结果表明，KGa随Na2CO3浓度、吸收液流量的增加而增加，随吸收温度、进气流速的升高而降低；在高浓度H2S吸收过程中液相传质阻力不能忽略。     

PH3液相催化氧化净化研究

以Mn2 和Pd2 为催化剂的吸收液对含低浓度PH3的混合气进行了液相催化氧化净化研究.考察了催化剂配比、混合气中O2浓度、PH3初始浓度、反应温度、气体流量和吸收液pH与PH3净化效率的关系.结果表明,催化剂中Pd2 与Mn2 的质量比为1:4时可获得较佳的净化效果;随着混合气中O2浓度的增加,吸收液对PH3的净化效率有所提高;在20～75℃内,低温对PH3净化有利,较适宜的反应温度为20℃;较低的PH3初始浓度和低气体流量均有利于PH3的净化;较高的pH有利于吸收液中催化剂催化效能的发挥.吸收液对PH3的净化效率可达100%,但因吸收液中的金属离子易与催化氧化PH3产生的PO3-4形成沉淀,使金属离子脱离液相催化氧化系统,吸收液失效较快.     

低温结晶净化柠檬酸盐解吸贫液中硫酸根

在柠檬酸盐吸收—解吸脱硫技术中,完成循环吸收过程的吸收液由于烟气杂质催化和高温解吸变成了含低二氧化硫浓度、中高硫酸根浓度、多种有机酸共存的柠檬酸盐解吸贫液,造成吸收效率下降、SO2平衡容量严重降低,必须进行溶液净化,特别是净化硫酸根。针对这一问题,实验室采用低温结晶法净化柠檬酸盐脱硫解吸贫液模拟液,通过对溶液中硫酸根浓度分析,研究了不同反应时间、温度、初始硫酸根浓度、柠檬酸根总浓度和溶液p H对硫酸根去除效率的影响。结果表明,硫酸根去除率与冷冻温度和溶液p H有关。在柠檬酸根总浓度1.5 mol/L,初始硫酸根浓度40 g/L,冷冻温度3℃,p H 4.5的条件下,可将硫酸根净化至16.9 g/L。     

改性活性炭吸附净化黄磷尾气中的H2S

研究了以Cu2 离子活性溶液制备改性活性炭吸附净化黄磷尾气中H2S的相关问题,考察了改性活性炭制备过程中的浸渍液浓度、干燥温度和焙烧温度的影响,以及温度和氧含量对吸附的影响;并对空白活性炭、改性活性炭吸附前后做SEM表征.研究结果表明,浸渍液浓度0.05 mol/L、干燥温度120℃、焙烧温度250℃为改性活性炭制备的最佳条件;吸附反应阶段较适宜的温度为95℃,氧含量为1%;结合扫描电镜初步表明,改性后的活性炭S容量增加,吸附效果明显.     

Cu2+沉淀-氧化法脱除H2S废气回收硫磺研究

开发了一种用含Cu2 的溶液吸收H2S,并用Cu2 自氧化CuS制取硫磺的新工艺,Cu2 的还原产物CuCl2-由空气氧化再生,实现循环.考察了Cu2 浓度与净化效率的关系,研究了Cu2 、H 、助剂N的浓度和温度对Cu2 氧化CuS效率的影响及H 、助剂N的浓度、空塔气速和温度对Cu2 空气氧化再生效率的影响.结果表明,该技术对H2S废气净化效率100%,Cu2 氧化CuS及Cu2 空气氧化再生条件温和、效果好,终产物硫磺纯度高.     

生物膜法净化中浓度硫化氢的研究

基于中浓度H2S的生物治理研究较少的现状,利用生物膜法进行了以活性炭为填料净化中浓度H2S适宜条件的研究.考察了温度、营养液喷淋量、空塔气速、H2S初始浓度及pH与H2S净化效率的关系.结果表明,适宜条件为温度30 ℃、营养液喷淋量10 L/h、空塔气速0.16 m3/h、H2S初始质量浓度低于60 mg/m3和pH为2.0.在适宜条件下,生物膜填料塔对H2S的净化效率可达到90%以上.     

填料塔中钠碱溶液吸收低浓度SO2的体积传质系数

在填料吸收塔中测定和计算了钠碱溶液吸收烟气中低浓度SO2的体积总传质系数(KGa),并研究了进口气体中SO2浓度、气体流量、吸收液喷淋密度以及溶液中Na 浓度对体积传质总系数的影响.结果表明,进口气体中SO2浓度、气体流量及吸收液喷淋密度对KGa的影响较大;随着进口气体中SO2浓度的增大,KCa逐渐减小,而随着进口气体流量及吸收液喷淋密度的增大,KGa逐渐增大;吸收液中Na 浓度对KGa的影响较小.     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

实验室质量管理体系内部审核的策划

在实施ISO／IEC 17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核策划阶段的关键环节，提出审核范围确定、审核计划和抽样方案制订的质量控制要求，为有序高效地实施内部审核提供了技术方法。     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.     

Impact of overexploitation of shellfish: northeastern coast of India

India has a very extensive coastline of about 7515 km, rich in diverse living resources. These resources continue to deteriorate with rampant harvesting or are altered for other uses such as aquaculture and fisheries. The present paper deals with degrading coastal habitats in northeastern India, and projects the intensity of the stress arising from the collection of tiger prawn seeds (Penaeus monodon) for aquacultural farms and molluskan shells for poultry feed and edible lime. Indiscriminate exploitation of these resources leads to a heavy reduction of the species concerned and other associated marine communities. The magnitude of such destruction has been quantified. The impacts of biodiversity loss and their after-effects on the ecobalance of this coastal system have become a matter of great concern to ecologists to maintain security and sustainability. The authors propose a public awareness program on themes relating to the importance of biodiversity for human livelihoods.     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.