Post-combustion syntheses of PCDD/F and PBDD/F from halogen-rich fuel is suppressed by a pebble heater technology

GOAL, SCOPE AND BACKGROUND: Changes in German and European legislation shifted processing of polymer-rich shredding residues (SR) from landfill to thermal treatment. However, when waste of electric and electronic equipment (WEEE) is the source of SR, thermal treatment is complicated by halogens as well as the presence of polybrominated dioxins and furans (PBDD/F) and brominated flame retardants (BFR). Hence, WEEE requires high temperature incineration with sufficient residence times. Post-combustion synthesis of polyhalogenated dioxins and furans (PXDD/F) is dominant in the temperature range between 250-450 degrees C. Thus, a very rapid gas cooling from 450 degrees to 250 degrees C is important for proper raw gas treatment. The pebble heater technology developed by ATZ Entwicklungszentrum (Sulzbach-Rosenberg, Germany) might serve as an alternative to the state-of-the-art quench cooling. It is based on the application of a pebble bed of natural bulk material, which the exhaust gases flows through radially. It provides an excellent heat transfer and a temperature gradient in the range of 1,500-2,000 K/m. The paper presents data of a pilot application of the pebble heater technology for the treatment of raw gas derived from the incineration of polymeric materials from WEEE. METHODS: A liquid fuel was chosen in order to minimise technical modifications of the plant. It was analysed for halogens by x-ray fluorescence, for brominated flame retardants by HPLC-UV/MS and for PXDD/F by GC-HRMS. Combustion gases were rapidly cooled down to temperatures below 200 degrees C and emissions of PBDD/F and PCDD/ F were estimated without further off-gas treatment. PBDD/F emissions were computed as PCDD/F toxicity equivalents applying two different calculation approaches. RESULTS AND DISCUSSION: PCDD/F emissions accounted for 0.04 ng I-TEQ/Nm3 and are in compliance with European emission limits. Calculated PBDD/F toxicity equivalents exceeded the emission limit of 0.1 ng I-TEQ/Nm3 by factors of 75 and 208 depending on the calculation approach. A mass balance of PBDD/F and PCDD/F congeners revealed an efficient elimination of more than 95% in most cases. Lower reduction rates (76% for 2,3,7,8-TeBDF and 82% for 1,2,3,7,8-PeBDF) were attributed to incomplete combustion. An intended recovery of halogens by one-stage scrubbing downstream of the pebble heater was ineffective, recovering 28% of the applied chlorine and 9% of the bromine, only. CONCLUSIONS: Our pilot incineration test indicates that the pebble heater technology can effectively suppress a post-combustion synthesis of PCDD/F and PBDD/F, resulting in low PCDD/F emission levels without further off-gas treatment. The presented data state that WEEE is sensible to incomplete combustion, which will lead to increased PBDD/F emissions without increasing PCDD/F emission limits. This finding is especially relevant for small and low-technical incineration appliances, which have been reported to treat WEEE in developing countries and are considered to serve as a significant source of PXDD/F these days. RECOMMENDATIONS AND PERSPECTIVES: Monitoring of PCDD/F emissions only might considerably underestimate the total emission of dioxins and dioxin-like compounds. It is therefore an ineffective means for assessing resulting health risks, at least for those waste treatment plants which are considered to handle the increasing amounts of PBDD/ F-containing polymers from WEEE in future. Consequently, it is recommended to initiate a screening programme for PXDD/F emissions in large scale incineration facilities which are capable of treating WEEE shredder residues.     

Distribution of polybrominated diphenyl ethers (PBDEs) and polybrominated dibenzo-p-dioxins and dibenzofurans (PBDD/Fs) in municipal solid waste incinerators

The stack flue gases and the ashes in different units of two municipal solid waste incinerators (MSWIs) are sampled to investigate the characteristics of polybrominated diphenyl ethers (PBDEs), polybrominated dibenzo-p-dioxins and dibenzofurans (PBDD/Fs), and polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). Bottom ashes (BA) exhibited much higher PBDD/F (8.11-52.2 pg TEQ/g) and PBDE contents (20.4-186 ng/g) than those of fly ashes (0.0932-2.02 pg TEQ/g and 0.332-25.5 ng/g), revealing that the PBDD/Fs and PBDEs in the feeding waste may not be completely destroyed. The PBDE concentrations/contents in the stack flue gases (26.1-109 ng/Nm³) and in the BA (20.4-186 ng/g) of the MSWIs could reach three orders higher than those in the atmosphere and reference soils. PBDE contributions to the environment from the stack flue gases or the reutilization of BA of MSWIs should not be ignored from the developing PBDE inventory.     

Environmental issues and management strategies for waste electronic and electrical equipment

Issues surrounding the impact and management of discarded or waste electronic and electrical equipment (WEEE) have received increasing attention in recent years. This attention stems from the growing quantity and diversity of electronic and electrical equipment (EEE) used by modern society, the increasingly rapid turnover of EEE with the accompanying burden on the waste stream, and the occurrence of toxic chemicals in many EEE components that can pose a risk to human and environmental health if improperly managed. In addition, public awareness of the WEEE or "e-waste" dilemma has grown in light of popular press features on events such as the transition to digital television and the exportation of WEEE from the United States and other developed countries to Africa, China, and India, where WEEE has often not been managed in a safe manner (e.g., processed with proper safety precautions, disposed of in a sanitary landfill, combusted with proper air quality procedures). This paper critically reviews current published information on the subject of WEEE. The definition, magnitude, and characteristics of this waste stream are summarized, including a detailed review of the chemicals of concern associated with different components and how this has changed and continues to evolve over time. Current and evolving management practices are described (e.g., reuse, recycling, incineration, landfilling). This review discusses the role of regulation and policies developed by governments, institutions, and product manufacturers and how these initiatives are shaping current and future management practices.     

电子与电器废弃物资源化处理技术

当今世界电子、电器工业快速发展,层出不穷的技术创新与持续膨胀的市场需求加速了电子与电器设备的更新换代,产生了大量的电子与电器废弃物(WEEE).鉴于WEEE所带来的严重的环境问题及其所含有的金属、贵金属、塑料及玻璃等高利用价值的材料,对WEEE进行资源化再循环处理已成为人们关注的热点.WEEE组成材料在密度、铁磁性、导电性等物理性质方面的较大差异使采用环境友好的机械物理方法对其进行资源化再循环处理成为可能.就WEEE拆解及其所含物质机械物理分离研究进展进行了综述.     

Thermal formation of PBDD/F from tetrabromobisphenol A--a comparison of polymer linked TBBP A with its additive incorporation in thermoplastics

For a long period, polybrominated flame retardants are under discussion because of the formation of polybrominated dibenzo-p-dioxins (PBDD)/dibenzofurans (PBDF) (PBDD/F) in case of thermal stress. Concerning polymer linked tetrabromobisphenol A (TBBP A), formation of PBDD/F was commonly presumed to be sterically hindered because of the covalent fixation into the polymer backbone. Combustion experiments with additively incorporated TBBP A compared with its polymer linkage revealed, that this assumption is incorrect and has to be revised. Under same conditions, similar PBDD/F concentrations in the range of 17.5-19.6 mg PBBD/F per kg TBBP A applied were analyzed. PBDD/F homologue distribution patterns were almost identical predominated by low brominated PBDF. These findings for PBDD/F formation have to be considered in future discussions regarding thermal stress caused by combustion or recycling processes, including other flame retardants bound in polymer matrix, e.g. polybrominated polystyrene (PS), or those with molecular structures showing less analogy to PBDD/F, like hexabromocyclododecane. The second aspect introduced, is the influence of different plastics on the formation rates of PBDD/F. In this context, combustion experiments were performed in an atmosphere consisting of synthetic air and HBr. PBDD/F concentrations were 8.47 mg/kg polyethylene, 1.67 mg/kg PS, 3.92 mg/kg phenolic resin and 18.1 mg/kg epoxy resin. Distribution patterns of PBDD/F homologues could partly be correlated with the occurrence of the precursors polybrominated benzenes and phenols.     

Interactive analysis of waste recycling and energy recovery program in a small-scale incinerator

Conflicting goals affecting solid waste management are explored in this paper to find the best implementation of resource recovery with a small-scale waste-to-energy process. Recycling paper and plastic material often leaves a shortage of thermal energy to support incineration that forces operators to supplement the process with auxiliary fuels. Although there are considerable profits to be made from material recovery, the increase of fuel usage causes conflict given that it is cost prohibitive. A series of trials performed on a small-scale 1.5-t/day incineration plant with a cyclone heat recovery system found that material recycling can impede performance. Experimental results are expressed as empirical regression formulas with regard to combustion temperature, energy transfer, and heat recovery. Process optimization is possible if the waste moisture content remains <30%. To test the robustness of the optimization analysis, a series of sensitivity analyses clarify the extent of material recycling needed with regard to plastic, paper, and metal. The experiments also test whether the moisture in the waste would decrease when recycling paper because of its exceptional capacity to absorb moisture. Results show that recycling paper is strongly recommended when the moisture content is >20%, whereas plastic recycling is not necessary at that moisture condition. Notably, plastic recovery reduces the heat needed to vaporize the water content of the solid waste, thus it is recommended only when the moisture content is <10%. For above-normal incineration temperatures, plastic recycling is encouraged, because it removes excess energy. Metal is confirmed as an overall priority in material recycling regardless of the moisture content of the incoming waste.     

废电子电器回收处理体系研究

分析了废电子电器回收处理体系的问题,提出了一种适合我国国情的废电子电器回收处理体系模式,并对国家对废电子电器回收处理体系的支持问题进行了讨论。     

Heavy metal contamination characteristic of soil in WEEE (waste electrical and electronic equipment) dismantling community: a case study of Bangkok,Thailand

Sue Yai Utit is an old community located in Bangkok, Thailand which dismantles waste electrical and electronic equipment (WEEE). The surface soil samples at the dismantling site were contaminated with copper (Cu), lead (Pb), zinc (Zn), and nickel (Ni) higher than Dutch Standards, especially around the WEEE dumps. Residual fractions of Cu, Pb, Zn, and Ni in coarse soil particles were greater than in finer soil. However, those metals bonded to Fe-Mn oxides were considerably greater in fine soil particles. The distribution of Zn in the mobile fraction and a higher concentration in finer soil particles indicated its readily leachable character. The concentration of Cu, Pb, and Ni in both fine and coarse soil particles was mostly not significantly different. The fractionation of heavy metals at this dismantling site was comparable to the background. The contamination characteristics differed from pollution by other sources, which generally demonstrated the magnification of the non-residual fraction. A distribution pathway was proposed whereby contamination began by the deposition of WEEE scrap directly onto the soil surface as a source of heavy metal. This then accumulated, corroded, and was released via natural processes, becoming redistributed among the soil material. Therefore, the concentrations of both the residual and non-residual fractions of heavy metals in WEEE-contaminated soil increased.     

Ah Receptor Agonists in UV-exposed Toluene Solutions of Decabromodiphenyl Ether (decaBDE) and in Soils Contaminated with Polybrominated Diphenyl Ethers (PBDEs) (9 pp)

Goal, Scope and Background The use of polybrominated diphenyl ethers (PBDEs) as flame retardants increases the risk for emissions of other brominated compounds, such as polybrominated dibenzodioxins (PBDDs) and dibenzofurans (PBDFs). The large homology in structure of PBDD/Fs and mechanism of toxic action, i.e. the capacity to activate the Ah receptor (AhR) pathway, compared to their well-studied chlorinated analogues, justifies a raised concern to study the environmental levels and fate of these compounds. Decabromodiphenyl ether (decaBDE) is the most widely used PBDE today. Studies on photolytic debromination of decaBDE in organic solvents have shown debromination of decaBDE, as well as formation of PBDFs. However, little is known about the transformation mechanisms and there are only scarce data on photoproducts and PBDE transformation in environmentally relevant matrices. In this study, mechanism-specific dioxin bioassays were used to study photolytic formation of AhR agonists in toluene solutions of decaBDE. In addition, the influence of irradiation time and UV-light wavelength on the formation was studied. PBDE congener patterns and presence of PBDD/Fs were analysed. Further, AhR agonists were analysed in agricultural soils contaminated with PBDEs. Soils were also exposed to UV-light to study changes in AhR agonist levels. Methods Toluene solutions of decaBDE were irradiated using three different spectra of UV-light, simulating UV-A (320-400 nm), UV-AB (280-400 nm), and UV-ABC (250-400 nm). Additionally, decaBDE solutions were exposed to narrow wavelength intervals (10 nm bandwidth) with the central wavelengths 280, 290, 300, 310, 320, 330, 340, 350, 360 nm. AhR agonists in decaBDE solutions were analysed with two different bioassays, the chick embryo liver-cell assay for dioxins (Celcad) and the dioxin responsive, chemically activated luciferase expression assay (DR-Calux). Also, the decaBDE solutions were analysed with LRGC-LRMS to obtain PBDE congener patterns for breakdown of decaBDE, and with HRGC-HRMS, for presence of PBDD/Fs. Four soils were exposed to UV-AB light, under both dry and moist conditions. Levels of AhR agonists in soil extract fractions, before and after UV-exposure, were analysed with the DR-Calux. Results and Discussion Significant levels of photoproducts able to activate the AhR pathway, up to 31 ng bio-TEQ/ml, were formed in UV-exposed decaBDE solutions. The transformation yield of decaBDE into AhR agonists was estimated to be at the 0.1%-level, on a molar basis. The net formation was highly dependent on wavelength, with the sample irradiated at 330 nm showing the highest level of dioxin-like activity. No activity was detected in controls. PBDE analysis confirmed decaBDE degradation and a clear time-dependent pattern for debromination of PBDE congeners. AhR agonist effect in the recalcitrant fractions of the soils corresponded to the levels of chemically derived TEQs, based only on chlorinated dioxin-like compounds in an earlier study. It was concluded that no significant levels of other AhR agonists, e.g. PBDFs, were accumulated in the soil. UV-light caused changes in AhR-mediated activity in the more polar and less persistent fractions of the soils, but it is not known which compounds are responsible for this. Recommendations and Perspective . The laboratory experiments in this study show that high levels of AhR agonists can be formed as photoproducts of decaBDE and it is important to elucidate if and under which conditions this might occur in nature. However, soil analysis indicates that photoproducts of PBDE do not contribute to the accumulated levels of persistent dioxin-like compounds in agricultural soil. Still, more data is needed to fully estimate the environmental importance of PBDE photolysis and occurrence of its photoproducts in other environmental compartments. Analysis with dioxin bioassays enabled us to gather information about photoproducts formed from decaBDE even though the exact identities of these compounds were not known. Conclusion Bioassays are valuable for studying environmental transformation processes like this, where chemical analysis and subsequent toxicological evaluation requires available standard compounds and information on toxicological potency. The use of bioassays allows a rapid evaluation of toxicological relevance.     

Brominated flame retardants — Ubiquitous environmental pollutants?

Biological samples from marine environments have been analyzed with a technique selectively sensitive for brominated organic compounds. All samples contained a number of such substances and some of them were characterized as polybrominated biphenyls (PBB) and diphenyl ethers (PBDE), respectively. The chromatographic pattern of these two groups agreed well with the corresponding patterns from two commercial flame retardants based on these types of substances. The samples analyzed so far (seal, guillemots and white-tailed sea eagle) were collected in the Baltic, the North Sea and the Arctic Ocean. The levels of PBB and PBDE were two to five times higher in samples from the Baltic than in samples from the other places, possibly indicating local sources. The presence of these compounds in samples from remote areas indicates a world-wide distribution and emphasizes the risk in the use of polyhalogenated hydrocarbons.     

Occurrence and congener profiles of polybrominated diphenyl ethers (PBDEs) in environmental samples from coastal British Columbia, Canada

Environmental levels and detailed congener profiles (31 congeners and 3 coeluting congener groups) of polybrominated diphenyl ethers (PBDEs) were assessed in a number of biota samples taken over a large geographic range covering harbours and industrial sites on Canada's West Coast. Additionally, PBDE congener profiles were determined using semipermeable membrane devices (SPMDs) deployed in the Fraser River, the river in Western Canada with the largest industrial activity. PBDE levels detected in biota were between 4 and 2300 ng/g lipid and these levels were compared with those reported in selected European biota to provide a wider perspective on PBDE contamination on Canada's West Coast. Thirteen-congener PBDE patterns in the environmental samples were examined using principal component analysis (PCA), and additionally, comparisons were made between the PBDE profiles in the sample groups and commercially used PBDE technical mixtures (e.g., Bromkals) on a percent composition basis. PCA on congener specific data revealed that PBDE patterns are remarkably similar over a wide geographical range in Western Canada, however, the general pattern in environmental samples varies significantly from those of the predominant technical mixtures. Finally, correlations between PBDE and other persistent and toxic co-occurring contaminants found in Dungeness crab were determined.     

我国电子废弃物管理与资源化对策

电子废弃物对人类环境的影响,已成为全球化的问题。通过对发达国家关于电子废弃物管理以及资源化技术的进展回顾,针对我国目前的情况提出相应的对策:制定延伸生产者责任以及有害物质的停用限期的相应法规;建立电子废弃物回收网络体系;通过国家政策和经济的扶持,尽快建立专门处理电子废弃物的机构;加快我国电子废弃物处理技术的步伐,尽快提高现有工艺及设备。     

Polybrominated diphenyl ethers (PBDEs), polybrominated dibenzo-p-dioxins/dibenzofurans (PBDD/Fs) and monobromo-polychlorinated dibenzo-p-dioxins/dibenzofurans (MoBPXDD/Fs) in the atmosphere and bulk deposition in Kyoto, Japan

Polybrominated diphenyl ethers (PBDEs), polybrominated dibenzo-p-dioxins/dibenzofurans (PBDD/Fs) and monobromo-polychlorinated dibenzo-p-dioxins/dibenzofurans (MoBPXDD/Fs) in atmosphere, bulk atmospheric deposition and soil in Kyoto, which is an urban city in Japan, were measured. Decabromodiphenyl ether (D(10)BDE, BDE-209) was detected in relatively high concentrations compared to other PBDE congeners in most samples. Similar results, in which D(10)BDE was predominantly detected, were reported in other studies in Japan. However, these homologue profiles differ from those of studies conducted in North America. The partitioning of semivolatile organic compounds between atmospheric gas phase and particulate-associated phase is an important factor in their environmental behavior. In this study, atmospheric particulate phase fraction (f(P)) of the brominated compounds increased with increasing bromine number, and f(P) was higher in samples collected in winter than in those collected in summer. Moreover, f(P) of PBDFs and MoBPXDFs was higher than that of PCDFs with the same halogen number. These results agree well with expectations from the vapor pressure of the brominated compounds and PCDD/Fs. Among the brominated compounds in the atmosphere, the level of MoBPXDD/Fs correlates positively with that of PCDD/Fs. This relationship has been previously observed in waste incineration samples. These results suggest that one of the sources of MoBPXDD/Fs in the atmosphere is incineration byproduct. The level of PBDD/Fs seems to correlate positively with that of PBDEs. This relationship suggest that the PBDD/Fs in the atmosphere relate to PBDEs, which is an impurity of PBDE products, or formed by the manufacture or combustion of plastics containing PBDEs.     

Interactive Analysis of Waste Recycling and Energy Recovery Program in a Small-Scale Incinerator

Abstract

Conflicting goals affecting solid waste management are explored in this paper to find the best implementation of resource recovery with a small-scale waste-to-energy process. Recycling paper and plastic material often leaves a shortage of thermal energy to support incineration that forces operators to supplement the process with auxiliary fuels. Although there are considerable profits to be made from material recovery, the increase of fuel usage causes conflict given that it is cost prohibitive. A series of trials performed on a small-scale 1.5-t/day incineration plant with a cyclone heat recovery system found that material recycling can impede performance. Experimental results are expressed as empirical regression formulas with regard to combustion temperature, energy transfer, and heat recovery. Process optimization is possible if the waste moisture content remains <30%. To test the robustness of the optimization analysis, a series of sensitivity analyses clarify the extent of material recycling needed with regard to plastic, paper, and metal. The experiments also test whether the moisture in the waste would decrease when recycling paper because of its exceptional capacity to absorb moisture. Results show that recycling paper is strongly recommended when the moisture content is >20%, whereas plastic recycling is not necessary at that moisture condition. Notably, plastic recovery reduces the heat needed to vaporize the water content of the solid waste, thus it is recommended only when the moisture content is <10%. For above-normal incineration temperatures, plastic recycling is encouraged, because it removes excess energy. Metal is confirmed as an overall priority in material recycling regardless of the moisture content of the incoming waste.     

Revisiting e-waste management practices in selected African countries

ABSTRACT

African countries are among the prime destinations of electronic waste (e-waste) also called Waste of Electrical and Electronic Equipment (WEEE), and have been challenged with the management of its environmental and health impacts. This paper was carried out to understand the e-waste sector and policy responses in selected African countries. Data for the study were generated from sources; such as policy documents, legislations and literature. Findings show that the import of WEEE is on rising in Africa while landfill and incineration continued to be widely used handling approaches. Countries studied lack WEEE specific national policies and stringent policy instruments to enforce proper collection and recycling systems. Despite the start-ups in emerging recycling operations, a major gap is that informal e-waste actors dominate the e-waste chain from collection to material extraction and refurbish activities through rudimentary tools that cannot detect toxic elements. Tackling the problem demands integrated multi-actor interventions with multiple stakeholders to reduce WEEE inflow on one hand, and ramping up safe recycling capacity on the other hand.     

Polybrominated, polychlorinated and monobromo-polychlorinated dibenzo-p-dioxins/dibenzofurans and dioxin-like polychlorinated biphenyls in marine surface sediments from Hong Kong and Korea

In this study we investigated occurrences and distribution patterns of dioxin-related compounds (DRCs) such as polybrominated dibenzo-p-dioxins/dibenzofurans (PBDD/Fs), polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDD/Fs), monobromo-polychlorinated dibenzo-p-dioxins/dibenzofurans (MoBPCDD/Fs) and dioxin-like polychlorinated biphenyls (DL-PCBs) in marine surface sediments collected from the coastal waters of Hong Kong and Korea. In most sampling sites, concentrations of PCDDs were the highest, followed by DL-PCBs, PCDFs, PBDFs, PBDDs, MoBPCDDs and MoBPCDFs in this order. Levels of PBDD/Fs were generally 1-2 orders of magnitude lower than chlorinated analogues. Levels of PCDDs are higher than PCDFs in Hong Kong while levels of PBDFs are higher than PBDDs in Korea (p < 0.05). Report of PBDD/Fs and MoBPCDD/Fs in sediments from East Asian countries is novel and original. Environmental levels of PBDD/Fs are supposed to start increasing in accordance with rising production, use and disposal of brominated flame retardants (BFRs) and recycling processes of e-waste in Asian developing countries.     

A bibliometric analysis on waste electrical and electronic equipment research

Environmental Science and Pollution Research - Waste electrical and electronic equipment (WEEE) contains both toxic and valuable materials. Due to rapid development of information and communication...     

Hazardous substances in indoor dust emitted from waste TV recycling facility

Various hazardous substances contained in waste TV sets might be released into environment via dust during recycling activities. Two brominated flame retardants (BFRs), polybrominated diphenyl ethers (PBDEs), and tetrabromobisphenol A (TBBPA), and five kinds of heavy metals (Cu, Pb, Cd, Cr, and Ni) were detected in indoor dust collected from two workshops (TV dismantling workshop and subsequent recycling workshop). PBDEs concentrations in dust from waste wires recycling line (722,000 ng/g) were the highest among the studied sites, followed by those in manual dismantling–sorting line (117,000 ng/g), whereas TBBPA concentrations were the highest in manual dismantling–sorting line (557 ng/g) and printed circuit board (PCB) recycling line (428 ng/g). For heavy metals, Cu and Pb were the most enriched metals in all dust samples. The highest concentration of Pb (22,900 mg/kg) was found in TV dismantling workshop-floor dust. Meanwhile, Cu was the predominant metal in dust from the PCB recycling line, especially in dust collected from electrostatic separation area (42,700 mg/kg). Occupational exposure assessment results showed that workers were the most exposed to BDE-209 among the four PBDE congeners (BDE-47, BDE-99, BDE-153, and BDE-209) in both workshops. The hazard quotient (HQ) indicated that noncancerous effects were unlikely for both BFRs and heavy metals (HQ?<?1), and carcinogenic risks for Cd, Cr, and Ni (risk?<?10^?6) on workers in two workshops were relatively low.     

PBDF and PBDD from the combustion of bromine containing flame retarded polymers: A survey

The formation of polybrominated dibenzofurans (PBDF) and dibenzodioxins (PBDD) during the pyrolysis of different polymers containing brominated organic flame retardants was investigated. The pyrolyses were conducted at two different temperatures (600°C and 800°C) using three different oven configurations. Both the pyrolysis gases and the solid residues were analysed for PBDF and PBDD.

PBDF were found in almost all samples, but both the concentration and the degree of bromination varied greatly. The largest yields of PBDF in the percent range were measured in the pyrolysis products of polymers containing brominated diphenyl ethers. The other flame retardants generally yielded only a few ppm of PBDF. PBDD are formed only in a few samples and related to the PBDF in very low concentrations.     

Present status of recycling waste mobile phones in China: a review

A large number of waste mobile phones have already been generated and are being generated. Various countries around the world have all been positively exploring the way of recycling and reuse when facing such a large amount of waste mobile phones. In some countries, processing waste mobile phones has been forming a complete industrial chain, which can not only recycle waste mobile phones to reduce their negative influence on the environment but also turn waste into treasure to acquire economic benefits dramatically. However, the situation of recycling waste mobile phones in China is not going well. Waste mobile phones are not formally covered by existing regulations and policies for the waste electric and electronic equipment in China. In order to explore an appropriate system to recover waste mobile phones, the mobile phone production and the amount of waste mobile phones are introduced in this paper, and status of waste mobile phones recycling is described; then, the disposal technology of electronic waste that would be most likely to be used for processing of electronic waste in industrial applications in the near future is reviewed. Finally, rationalization proposals are put forward based on the current recovery status of waste mobile phones for the purpose of promoting the development of recycling waste mobile phones in developing countries with a special emphasis on China.