软锰矿-污泥活性炭的制备及其对废水中铅离子的吸附

以城市污水处理厂的剩余污泥为原料,掺杂一定量的软锰矿,采用氯化锌活化法制备一种软锰矿-污泥活性炭,并运用比表面积测定、电镜扫描、红外光谱分析及O2-TPO等表征手段对软锰矿-污泥活性炭及纯污泥活性炭进行了结构特性的比较分析,证明添加软锰矿将污泥活性炭的比表面积提高52.33%,是由于在制备过程中软锰矿催化了污泥中有机质的分解,同时也为新生炭提供了更多的骨架,促进了积炭反应的发生。软锰矿-污泥活性炭和纯污泥活性炭对废水中铅离子的吸附实验表明:当Pb2+初始浓度为40 mg/L、pH为5.0、活性炭用量为2 g/L、吸附时间为1 h时,软锰矿-污泥活性炭对废水中Pb2+的去除率可达88%,效果明显优于纯污泥活性炭。常温下软锰矿-污泥活性炭对Pb2+的吸附符合Lang-muir吸附等温式。     

改性污泥活性炭对水中镉离子的吸附性能

以城市污水处理厂的剩余污泥为原料,氯化锌为活化剂制备污泥活性炭,对一部分污泥活性炭用6.0 mol/L的硝酸进行改性,并研究了未改性和改性的污泥活性炭对Cd2＋的吸附行为的影响。结果表明,在pH为5.0、Cd2＋初始浓度为100 mg/L、吸附剂投加量为2.0 g/L、反应温度为25℃时,未改性的污泥活性炭吸附容量为8.45 mg/g,硝酸改性的污泥活性炭吸附容量达到了23.35 mg/g。改性和未改性的污泥活性炭对Cd2＋都有较好的吸附容量,硝酸改性大幅度提高了污泥活性炭对Cd2＋的吸附性能。常温下改性污泥活性炭对Cd2＋的吸附符合Langmuir吸附等温式。     

玉米芯掺杂对污泥基活性炭性能的影响

针对以城市污水厂剩余污泥为原料制备的污泥基活性炭微孔性差、比表面积低的缺陷,将一定比例玉米芯掺杂到污泥中以期改善活性炭性质。通过对活性炭的比表面积、孔结构、碘值、表面官能团测定以及表面电镜分析,探讨了不同比例玉米芯掺杂对活性炭物理化学性质的影响,并以苯酚和硝基苯为目标物,对比考察所制活性炭对有机物的吸附性能。实验结果表明,随着玉米芯掺杂比例的提高,活性炭微孔体积及比表面积明显增大,但活性炭表面官能团种类及数量变化不明显。所制活性炭表面都以酸性基团为主。结果显示苯酚和硝基苯吸附值与活性炭表面酸性基团含量关系密切,因此,玉米芯的掺杂对苯酚和硝基苯的吸附没有明显的促进作用。     

微波法污水厂污泥制备活性炭的研究

研究了以污水厂污泥为原料、微波辐照下磷酸活化法制备污泥活性炭的工艺条件,探讨了微波功率、辐照时间以及磷酸浓度对活性炭碘值的影响.结果表明,微波功率480 W、辐照时间315 s、磷酸浓度40%～45%的条件下,制备的污泥活性炭碘值为301 mg/g,总孔孔容是0.37 mL/g,平均孔径8.8 nm,比表面积168 m2/g.将该污泥活性炭用于处理TNT红水,吸附效果良好.     

污泥活性炭对Cr(Ⅵ)的吸附研究

研究了污泥活性炭对含Cr(Ⅵ)废水的吸附性能.利用西安某污水处理厂未消化脱水污泥,采用ZnCl2化学活化热解炭化法制备污泥活性炭,研究其处理含Cr(Ⅵ)废水的效果,考察其吸附Cr(Ⅵ)的动力学行为.结果表明,最佳吸附条件为溶液pH在1左右、污泥活性炭投加量5 g/L、吸附时间10 min、Cr(Ⅵ)初始质量浓度10 m...     

亚甲基蓝在污泥活性炭上的吸附

以剩余污泥为原料,氯化锌为活化剂制备污泥活性炭。研究了初始pH值、吸附温度及离子强度对污泥活性炭吸附亚甲基蓝效果的影响。采用高分辨电子扫描电镜(SEM)和氮吸脱附曲线对污泥活性炭进行了表征。结果表明,随着pH值的升高,吸附量增大,碱性条件下最好。在15～55℃的范围内,亚甲基蓝的吸附量先增加后降低,温度为35℃时吸附量达到最大值。加入氯化钠后的污泥活性炭的吸附能力变弱,但随着离子强度的增大,变弱的强度减少。污泥活性炭以中孔为主和污泥活性炭具有不规则结构,预示着污泥活性炭较高的吸附能力。污泥活性炭对亚甲基蓝的吸附符合Lang-muir等温吸附方程。污泥壳活性炭对亚甲基蓝的吸附符合二级反应动力学方程反应特征。     

微波法污水厂污泥制备活性炭的研究

研究了以污水厂污泥为原料、微波辐照下磷酸活化法制备污泥活性炭的工艺条件,探讨了微波功率、辐照时间以及磷酸浓度对活性炭碘值的影响.结果表明,微波功率480 W、辐照时间315 s、磷酸浓度40%～45%的条件下,制备的污泥活性炭碘值为301 mg/g,总孔孔容是0.37 mL/g,平均孔径8.8 nm,比表面积168 m2/g.将该污泥活性炭用于处理TNT红水,吸附效果良好.     

炭材料调理改善活性污泥脱水性能的影响机制

活性污泥中的胞外聚合物EPS含黏性蛋白类物质并高度亲水,调控污泥中溶解性EPS和溶解性蛋白类物质是改善污泥脱水的有效途径。通过使用不同炭材料调理污泥的方法来观察污泥脱水性能的变化,深入解析污泥絮体及EPS含量和组分的变化特征。结果表明:炭材料调理污泥可以改善其脱水性,且炭材料吸附容量越大对污泥脱水性改善效果越好;不同炭材料对污泥絮体影响效果不同,经过未改性活性炭(AC-0)、HNO3改性活性炭(AC-1)和石墨调理的污泥絮体粒径变大,经酸碱交替改性活性炭(AC-5)调理的污泥絮体粒径变小;炭材料调理后EPS中蛋白类的荧光峰A、B和腐殖酸、富里酸的荧光峰C、D都得到有效降低,且其对腐殖酸和富里酸的吸附效果比蛋白类物质要好,对低分子质量物质和中分子质量物质的吸附效果要好于对大分子质量物质的吸附效果。     

基于响应曲面法优化生物质污泥活性炭的制备方法

针对传统技术制备污泥活性炭的比表面积不高、吸附值低等不足,通过在污泥中添加核桃壳以改善污泥原料缺陷,研究了活化剂种类、核桃壳加量、活化温度、活化时间、活化剂浓度及浸渍比等影响活性炭吸附能力的制备条件。在优化后的条件下制备出了高吸附性能的生物质污泥复合活性炭。结果表明:选择氯化锌作为活化剂,核桃壳加量20%、活化温度500℃、活化时间60 min、活化剂浓度2.5 mol·L-1、浸渍比1∶2.5为最优化制备条件。制备出的生物质污泥复合活性炭碘吸附值为574.11 mg·g-1,产率为43.93%。     

Fenton法制备污泥基活性炭及其性能表征

污泥基活性炭孔隙率低下是污泥资源化利用的主要制约因素,而Fenton法预处理污泥,可有效改善活性炭性质。通过考察H2O2投加量、H2O2/Fe2+、活化pH以及炭化条件等参数,确定了最佳污泥基活性炭制备条件:H2O2投加量为5%(质量分数),H2O2/Fe2+为5∶1(质量比),活化pH为3,活化时间为2.0h,污泥含固率为1.0%(质量分数),炭化温度为600℃,炭化时间为2.0h,炭化升温速率为10℃/min。此时,得到的污泥基活性炭吸附碘值为340mg/g,比表面积为353.563m2/g,孔容积为0.238cm3/g,微孔容积为0.095cm3/g。该活性炭对阳离子和阴离子染料(亚甲基蓝和甲基橙)具有良好的吸附性能,结果表明,对亚甲基蓝和甲基橙的吸附更符合Langmuir方程,且其饱和吸附量分别为71.53、57.73mg/g。对吸附动力学的拟合结果表明,该吸附更符合二级动力学方程。     

Powdered activated carbon coupled with enhanced coagulation for natural organic matter removal and disinfection by-product control: application in a Western Australian water treatment plant

The removal of organic precursors of disinfection by-products (DBPs), i.e. natural organic matter (NOM), prior to disinfection and distribution is considered as the most effective approach to minimise the formation of DBPs. This study investigated the impact of the addition of powdered activated carbon (PAC) to an enhanced coagulation treatment process at an existing water treatment plant on the efficiency of NOM removal, the disinfection behaviour of the treated water, and the water quality in the distribution system. This is the first comprehensive assessment of the efficacy of plant-scale application of PAC combined with enhanced coagulation on an Australian source water. As a result of the PAC addition, the removal of NOM improved by 70%, which led to a significant reduction (80-95%) in the formation of DBPs. The water quality in the distribution system also improved, indicated by lower concentrations of DBPs in the distribution system and better maintenance of disinfectant residual at the extremities of the distribution system. The efficacy of the PAC treatment for NOM removal was shown to be a function of the characteristics of the NOM and the quality of the source water, as well as the PAC dose. PAC treatment did not have the capacity to remove bromide ion, resulting in the formation of more brominated DBPs. Since brominated DBPs have been found to be more toxic than their chlorinated analogues, their preferential formation upon PAC addition must be considered, especially in source waters containing high concentrations of bromide.     

粉末活性炭对水中农药的吸附性能研究

研究了粉末活性炭对2,4-滴、呋喃丹、甲萘威和莠去津的吸附过程和吸附规律以及投炭量和水质对粉末活性炭吸附性能的影响。结果表明,粉末活性炭能有效去除4种农药;吸附规律符合Freundlich吸附等温线和Langmuir吸附等温线;吸附时间为30 min时,去离子水中的去除率已达到80%以上;随着投炭量的增加,去除率提高,粉末活性炭的吸附容量降低;在不同水质条件下,粉末活性炭的吸附等温线可能不同,因此在应急处理中,首先应该确定该水质下的吸附等温线,然后求出投炭量。     

PACT工艺处理PAM生产废水的实验研究

采用粉末活性炭活性污泥工艺(PACT)处理经凹凸棒土预处理后的聚丙烯酰胺(PAM)生产废水。实验考察了粉末活性炭(PAC)的投加对活性污泥处理系统的影响,并探讨了PAC投加量、曝气时间、水力停留时间等参数对降解反应的影响。结果表明:PAC的投加能提高水中溶解氧的利用率,改善污泥沉降性能,增强活性污泥系统对有机物的去除效果;在PAC投加量500 mg/L、曝气10 h的条件下,PACT工艺对PAM生产废水的处理效果良好,COD的去除率为80.8%,BOD5去除率为83.8%,丙烯酰胺(AM)去除率为84.2%。     

聚合氯化铝与粉末活性炭联合强化混凝处理垃圾渗滤液

研究了联合粉末活性炭与聚合氯化铝(PAC)强化混凝对垃圾渗滤液原水的处理效果。结果表明,在原水COD为4 100 mg/L、浊度为147 NTU、UV254为20的条件下,粉末活性炭的加入可以有效增加垃圾渗滤液中有机物的去除率,PAC投加量为0.6 g/L时,投加0.6 g/L粉末活性炭,COD的去除率由21.6%提高到29.1%,UV254去除率由29.8%提高到39.9%,剩余浊度由138 NTU降到133 NTU。该强化混凝过程使原水中溶解性小分子有机物的去除率提高显著,PAC投加量为0.6 g/L时,投加0.6 g/L粉末活性炭,在分子量小于1 kDa的范围内,UV254去除率由2.9%上升为10%。     

Removal of pesticides from surface waters by combined physicochemical processes. Part I: Dodine

The simultaneous action of powdered activated carbon and several coagulant agents on the removal of the fungicide dodine from spiked distilled water, was studied. As coagulants, ferric chloride (FeCl₃) and basic polyaluminium chlorosulfate ([Al(OH)_xCl_y(SO₄)_z]_n) were examined, using polyacrylamide, in certain cases, as coagulant aid (polyelectrolyte). The efficiency of dodine removal was investigated with respect to the added amount of powdered activated carbon (PAC), the pH value, as well as the type and dose of coagulant and polyelectrolyte. The experiments were performed applying the standard jar-test procedure. The initial concentration of dodine was 250 μg/L. At this concentration and pH range 5–8 it was found that a dose of 100 mg/L PAC was necessary to achieve more than 98% removal of dodine, whereas lower removal (91–93%) was obtained applying half the dose of PAC under the same conditions. However, when 10–100 mg/L FeCl₃ were simultaneously added with PAC, the removal efficiency increased to >98%, even with the half PAC dose.     

可吸附有机卤化物的深度处理实验研究

可吸附有机卤化物（AOX）是人为污染的重要标志之一,北京高碑店污水处理厂二级出水中约90％的AOX为可吸附有机氧化物（AOCl),研究了自氧氧化,粒状活性炭吸附,粉末活性炭吸附3种深度处理工艺对二级出水中AOX的去除作用,臭氧的氧化反应最多可去除约38％的AOX,粒状活性炭床可运行3200床体积,吸附容量为0.14mgAOX/g GH-16型活性炭,投加木质粉末活性炭200mg/L及25mg/L的聚合氯化铝,能去除24．7％的AOX。     

粉末活性炭强化常规处理工艺时混凝效能的研究

在水源水质突然变差时，为了保证饮用水水质和水厂的经济低耗运行。以松花江水为原水，采用不同投量的粉末活性炭(PAC)来强化常规处理工艺，通过实验考察了硫酸铝(AS)、聚合氯化铝(PACl)、复合铝铁（PAF）及后2种混凝剂分别与助凝剂高锰酸盐复合药剂（PPC）、活化硅酸配合使用时对浊度和COD_Mn的去除情况。实验结果表明：（1）在进水水质相同的情况下，以浊度和COD_Mn为控制指标，达到同样的处理效果时，制水成本比较的结果为PAF相似文献   

吸附-氧化法应急处理饮用水源突发苯酚污染的研究

以黄浦江上游水源地突发苯酚污染为背景，重点考察了粉末活性炭（PAC）吸附、高锰酸钾（KMnO4）氧化及两者联用技术的除酚效能。结果表明，活性炭及氧化剂种类的选择是影响处理效果的重要因素，微孔发达、比表面积巨大的竹炭对苯酚的去除效果明显优于煤质炭、椰壳炭和木质炭；KMnO4对苯酚的氧化能力强于次氯酸钠和高铁酸钾。增大PAC和KMnO4的投加量，可有效提高对苯酚的去除率；PAC吸附-KMnO4氧化联用技术可大大提高除酚效能，投加50mg／LPAC，2mg／LKMnO4可将初始浓度为250／μg／L和500／μg／L的含酚原水分别处理至18μg／L和66／μg／L，是应对高浓度苯酚突发污染的有效应急措施。     

A sorptive slurry bioscrubber for the control of acetone

A sorptive slurry bioscrubber adds powdered activated carbon (PAC) to a conventional suspended-growth bioscrubber. The activated carbon increases pollutant removal from the gas phase due to adsorption on carbon. The carbon is bioregenerated in the oxidation reactor and recycled to the scrubbing column. A three-stage, conventional bioscrubber was tested with and without carbon. The experiments showed that the PAC improved the removal efficiency of the system and that bioregeneration occurred. At an inlet gas-phase acetone concentration of 50 ppmv, the steady-state removal increased from 88 to 95% when activated carbon was added to the biological slurry.     

A Sorptive Slurry Bioscrubber for the Control of Acetone

ABSTRACT

A sorptive slurry bioscrubber adds powdered activated carbon (PAC) to a conventional suspended-growth bioscrubber. The activated carbon increases pollutant removal from the gas phase due to adsorption on carbon. The carbon is bioregenerated in the oxidation reactor and recycled to the scrubbing column. A three-stage, conventional bioscrubber was tested with and without carbon. The experiments showed that the PAC improved the removal efficiency of the system and that bioregeneration occurred. At an inlet gas-phase acetone concentration of 50 ppmv, the steady-state removal increased from 88 to 95% when activated carbon was added to the biological slurry.