Application of a permethrin immunosorbent assay method to residential soil and dust samples

A low-cost, high throughput bioanalytical screening method was developed for monitoring cis/trans-permethrin in dust and soil samples. The method consisted of a simple sample preparation procedure [sonication with dichloromethane followed by a solvent exchange into methanol:water (1:1)] with bioanalytical detection using a magnetic particle enzyme-linked immunosorbent assay (ELISA). Quantitative recoveries (83–126 %) of cis/trans-permethrin were obtained for spiked soil and dust samples. The percent difference of duplicate ELISA analyses was within ± 20 % for standards and ± 35 % for samples. Similar sample preparation procedures were used for the conventional gas chromatography/mass spectrometry (GC/MS) analysis except that additional cleanup steps were required. Recoveries of cis/trans-permethrin ranged from 81 to 108 % for spiked soil and dust samples by GC/MS. The ELISA-derived permethrin concentrations were highly correlated with the GC/MS-derived sum of cis/trans-permethrin concentrations with a correlation coefficient (r) of 0.986. The ELISA method provided a rapid qualitative screen for cis/trans-permethrin in soil and dust while providing a higher sample throughput with a lower cost as compared to the GC/MS method. The ELISA can be applied as a complementary, low-cost screening tool to prioritize and rank samples prior to instrumental analysis for exposure studies.     

Simultaneous Determination of Imidacloprid,Thiacloprid, and Thiamethoxam in Soil and Water by High-performance Liquid Chromatography with Diode-array Detection

Abstract

A high-performance liquid chromatography method with diode-array detection (HPLC-DAD) is described for the determination of three neonicotinoid insecticides imidacloprid, thiacloprid, and thiamethoxam in soil and water. The soil samples were extracted with acetonitrile, while the water samples were extracted using C₁₈ cartridges. The mean recoveries plus standard deviations for spiked soil samples were 82 ± 4.2% for thiamethoxam, 99 ± 4.2% for imidacloprid and 94 ± 1.4% for thiacloprid. The recoveries for water samples ranged from 87 ± 3.4% for thiamethoxam to 97 ± 3.9% for imidacloprid and 97 ± 2.6% for thiacloprid. The limits of quantitation (LOQ) were 0.1, 0.1, 0.01 mg/kg in soil (5 g), and 2, 2, 0.5 µg/L in water (50 mL) for thiamethoxam, imidacloprid, and thiacloprid, respectively.     

Monoclonal antibody produced by heterologous indirect enzyme-linked immunosorbent assay and its application for parathion residue determination in agricultural and environmental samples

A heterologous indirect enzyme-linked immunosorbent assay (ELISA) was developed, which was based on monoclonal antibody (Mab) to determine parathion residue in agricultural and environmental samples. Eight Mabs were produced by introducing the heterologous indirect ELISA into the screening procedure. It was shown that these Mabs had more broad-reactivity with twenty competitors than that of 5H7 (Mab produced by homologous screening). So it became much easier using these new Mabs to develop heterologous immunoassays. In addition, all the developed heterologous ELISAs could be used to determine parathion residue in semiquantitative or quantitative level, and their detection limitation (LOD) was around 2 ng/mL. Compared with the previous heterologous ELISA (hapten 11/5H7) with IC₅₀ of 13.3 ng/mL, a better heterologous ELISA (hapten 11/1E1) was obtained with IC₅₀ of 3.8 ng/mL, which improved the sensitivity 3.5 times. Finally, the latter was applied to parathion residue determination in spiked agricultural and environmental samples without extraction or cleanup. The average recoveries of parathion added to water, soil, cucumber, Chinese cabbage and carrot were between 80.4 % and 111.8 %. The LOD for water and soil samples was 5 ng/mL, and the LOD for cucumber, rice and corn samples was 10 ng/mL.     

Monitoring of atrazine in milk using a rapid tube-based ELISA and validation with HPLC

Although atrazine has been banned in the European Union since 2007 it still persists in soil from where it can enter the food chain. Milk-producing animals accumulate atrazine from contaminated feed and water and since large quantities of milk and milk products are consumed its quality should be constantly monitored. The objective of this investigation was to develop a simple tube ELISA procedure suitable for use in non-specialised laboratories and in the field. A polyclonal antibody raised in sheep and the hapten-gelatine conjugate was immobilised onto polystyrene tubes. This enables the colour produced to be read on a basic spectrophotometer. Milk samples were collected from three farms in different regions of Poland and diluted before immunoassay was performed. Samples were extracted with hexane-acetone for HPLC analysis. The amount of fat in the milk samples interferes with the dose response so it essential that the standards are prepared in the same samples matrix. A good correlation between 1% and 2% was found between the two methods in the analysis of real samples. However the ELISA procedure was more sensitive that the HPLC method since atrazine was detected in some samples by the ELISA but was not confirmed by the HPLC method. The study demonstrated that the simple antigen-coated tube assay provides a cost effective and valuable screening test that can be easily modified for direct use as a screening tool in the field.     

Determination of 2,4-Dichlorophenoxyacetic acid in food and water samples using a modified graphene oxide sorbent and high-performance liquid chromatography

Abstract

In the present work, dispersive micro-solid phase extraction (D-μ-SPE) method using magnetic graphene oxide tert-butylamine (GO/Fe₃O₄/TBA) nanocomposite, as an efficient sorbent, was applied for determining 2,4-dichlorophenoxyacetic acid (2,4-D) in water and food samples. Detection was carried out using high-performance liquid chromatography (HPLC) instrument. Influential parameters of D-μ-SPE such as sorbent and its amount, elution solvent and its volume, adsorption and desorption times and pH of sample solution were investigated and optimized. Under the optimized conditions, limit of detection and quantitation values were 0.007 and 0.02?μg/mL, respectively. Recovery data for several real samples were obtained within the range of 88.0–94.0% with a relative standard deviation (RSD) less than 7.5%. The proposed method was successfully applied to quantitative determination of 2,4-D in several vegetables and water samples.     

Comparison of Three Extraction Methods for 17 β-Estradiol in Sand,Bentonite, and Organic-Rich Silt Loam

Extraction is an important procedure for samples that contain soil because other compounds in soil may affect analysis of estrogens. This study was conducted to evaluate three different extraction methods for 17β-estradiol in soil. Sand, bentonite, and organic-rich silt loam were spiked with 1 mg kg^{? 1} of 17β-estradiol as a model compound of estrogens. 17β-estradiol and its metabolites, estrone and estriol, were extracted using (i) a modified Bligh and Dyer extraction, (ii) a pressurized fluid extraction, and (iii) a diethyl ether extraction, and measured by liquid chromatography tandem mass spectrometry. There were significant differences in the extraction efficiency for 17β-estradiol among the extraction methods and the soils: the efficiencies ranged from 10% to 97%. Overall, the diethyl ether extraction method had the largest efficiency of 17β-estradiol with 45% and 57% for bentonite and silt loam, respectively. Transformation of 17β-estradiol to estrone and estriol in the different extraction methods was less than 3.6% during the extraction procedures. This study underlined the importance of sample preparation for estrogen analysis in soil samples.     

Simultaneous analysis of triasulfuron, metsulfuron-methyl and chlorsulfuron in water and alkaline soils by high-performance liquid chromatography

A method capable of simultaneously detecting residues of three sulfonylurea herbicides at microgram/l and microgram/kg level in water and alkaline soils has been described. The method is based on solid phase extraction and HPLC with UV detection. In alkaline soils especially those containing low organic carbon it was possible to extract the herbicides with de-ionised water and no clean up step was needed. Soil samples spiked with technical grade triasulfuron, metsulfuron-methyl and chlorsulfuron were extracted twice by shaking with de-ionised water for one hour and centrifuging at 10,000 rpm for 15 minutes. Supernatants filtered through glass micro-fibre filters were passed through C18 cartridges previously pre-conditioned with methanol and de-ionised water at a flow rate of < 20 ml/min. Residues of the herbicides retained on the cartridge were eluted with acidified methanol. The eluate was analysed by HPLC. A C18 column was used with a mobile phase of methanol/water (40 + 60, V/V for for the herbicide residues were 1.0 microgram/l and 3 micrograms/kg in water and soil, respectively. The average recoveries for water samples ranged from 73-94%, while for soil samples recoveries were 77-97% for the three compounds studied.     

Comparison of in-house-developed ELISA with HPLC techniques for the analysis of atrazine residues

In-house developed ELISA was standardized to monitor atrazine residues in different environmental samples. The standard curve was linear, indicating an increase in log concentration with decrease in absorbance (%B/B₀ = 1.075–0.042 Log C; r = ?0.966). The middle of the test was at 75 ng/L and the lowest detection limit at 4 ng/L. ELISA significantly correlated with the high performance liquid chromatography (HPLC) (r = 0.990). Internal validation showed good accuracy and precision. Maximum atrazine residues were present in Jehlum River water/sediments and maize/sugarcane plant roots. Most of the food samples were found to be contaminated. ELISA required less clean-up steps than HPLC, but showed matrix effect in soil/colored extracts.     

Method Development for Determination of Fluroxypyr in Soil

Abstract

Four methods were developed for the analysis of fluroxypyr in soil samples from oil palm plantations. The first method involved the extraction of the herbicide with 0.05 M NaOH in methanol followed by purification using acid base partition. The concentrated material was subjected to derivatization and then cleaning process using a florisil column and finally analyzed by gas chromatography (GC) equipped with electron capture detector (ECD). By this method, the recovery of fluroxypyr from the spiked soil ranged from 70 to 104% with the minimum detection limit at 5 µg/kg. The second method involved solid liquid extraction of fluroxypyr using a horizontal shaker followed by quantification using high performance liquid chromatography (HPLC) equipped with UV detector. The recovery of fluroxypyr using this method, ranged from 80 to 120% when the soil was spiked with fluroxypyr at 0.1–0.2 µg/g soil. In the third method, the recovery of fluroxypyr was determined by solid liquid extraction using an ultrasonic bath. The recovery of fluroxypyr at spiking levels of 4–50 µg/L ranged from 88 to 98% with relative standard deviations of 3.0–5.8% with a minimum detection limit of 4 µg/kg. In the fourth method, fluroxypyr was extracted using the solid liquid extraction method followed by the cleaning up step with OASIS® HLB (polyvinyl dibenzene). The recovery of fluroxypyr was between 91 and 95% with relative standard deviations of 4.2–6.2%, respectively. The limit of detection in method 4 was further improved to 1 µg/kg. When the weight of soil used was increased 4 fold, the recovery of fluroxypyr at spiking level of 1–50 µg/kg ranged from 82–107% with relative standard deviations of 0.5–4.7%.     

Application of an ELISA to the quantification of carbamazepine in ground, surface and wastewaters and validation with LC-MS/MS

Carbamazepine is a psychiatric pharmaceutical widely detected in aquatic environments. Due to its generalized occurrence and environmental persistence it might be considered as an anthropogenic pollution indicator. In this research, a previously developed enzyme-linked immunosorbent assay (ELISA), based on a commercial monoclonal antibody, was applied to the quantification of carbamazepine in ground, surface and wastewaters and results were validated by liquid chromatography-tandem mass spectrometry (LC-MS/MS).The performance of the applied ELISA methodology was tested in the presence of high concentrations of sodium chloride and dissolved organic matter. The method was not significantly affected by matrix effects, being adequate for the quantification of carbamazepine in environmental samples, even without sample pre-treatment. This method allows the quantification of carbamazepine in the range of 0.03-10 μg L⁻¹, with a relative error lower than 30%. Due to a pH dependent cross-reactivity with cetirizine, an antihistaminic drug, the assay also enabled the quantification of cetirizine in the samples.The application of the developed method to the quantification of carbamazepine was performed by using environmental samples with very different matrices, collected in the geographical area of Ria de Aveiro, an estuarine system located in the North of Portugal. Carbamazepine was detected in all analyzed wastewater samples and in one surface water with concentrations between 0.1 and 0.7 μg L⁻¹. Validation with LC-MS/MS revealed that results obtained by ELISA are 2-28% overestimated, which was considered highly satisfactory due to the absence of sample pre-treatments.     

Reverse phase high performance liquid chromatographic determination of Baygon in water

Abstract

A simple analytical procedure for determination of Baygon in water is described. The Baygon residues are extracted on a C₁₈ SEP‐PAK cartridge and subsequently analyzed by reverse phase high performance liquid chromatography using ultraviolet detection at 272 nm. Water samples spiked with Baygon are found to give greater than 90 percent recoveries.

Concentration levels as low as 20 ppb can be easily detected by this method.     

Validation of QuEChERS method for the determination of some pesticide residues in two apple varieties

This study was undertaken to validate the “quick, easy, cheap, effective, rugged and safe” (QuEChERS) method using Golden Delicious and Starking Delicious apple matrices spiked at 0.1 maximum residue limit (MRL), 1.0 MRL and 10 MRL levels of the four pesticides (chlorpyrifos, dimethoate, indoxacarb and imidacloprid). For the extraction and cleanup, original QuEChERS method was followed, then the samples were subjected to liquid chromatography-triple quadrupole mass spectrometry (LC-MS/MS) for chromatographic analyses. According to t test, matrix effect was not significant for chlorpyrifos in both sample matrices, but it was significant for dimethoate, indoxacarb and imidacloprid in both sample matrices. Thus, matrix-matched calibration (MC) was used to compensate matrix effect and quantifications were carried out by using MC. The overall recovery of the method was 90.15% with a relative standard deviation of 13.27% (n = 330). Estimated method detection limit of analytes blew the MRLs. Some other parameters of the method validation, such as recovery, precision, accuracy and linearity were found to be within the required ranges.     

A rapid and sensitive fluoroimmunoassay based on quantum dot for the detection of chlorpyrifos residue in drinking water

A rapid and sensitive indirect competitive fluorescence-linked immunosorbent assay (cFLISA) method based on quantum dots as the fluorescence label coupled with secondary antibody (Ab₂) for the detection of chlorpyrifos in drinking water has been developed. The cFLISA method allowed for chlorpyrifos determination in a liner working range of 15.2–205.5 ng mL^?1. The 50 % inhibition value (IC₅₀) and the limit of detection (LOD) of the cFLISA were 50.2 ng mL^?1 and 8.4 ng mL^?1, while the IC₅₀ and the LOD of the conventhional enzyme linked immunosorbent assay (ELISA) were 95.3 ng- mL^?1 and 16.2 ng mL^?1, respectively. When the concentrations of chlorpyrifos were 200, 100 and 50 ng mL^?1, the recoveries ranged from 90.8 % to 108.2 % with a coefficient of variation (CV) of 7.5 %–15.2 %. In water sample analysis, the results of cFLISA were similar to those obtained from a cELISA and a high performance liquid chromatography (HPLC) method, while the detection time by cFLISA was reduced 0.5 h compared with ELISA. It showed that cFLISA could be used as a new screening method for the detection of pesticide residue.     

Highly sensitive and selective determination of malathion in vegetable extracts by an electrochemical sensor based on Cu-metal organic framework

Abstract

This article demonstrates the first application of a copper-based porous coordination polymer (BTCA-P-Cu-CP) as a carbon paste electrode (CPE) modifier for the detection of malathion. The electrochemical behavior of BTCA-P-Cu-CP/CPE was explored using cyclic voltammetry (CV) while chrono-amperometry methods were applied for the analytical evaluation of the sensor performance. Under optimized conditions, the developed sensor exhibited high reproducibility, stability, and wide dynamic range (0.6–24?nM) with the limits of detection and sensitivity equal to 0.17?nM and 5.7 µAnMcm^?1, respectively, based on inhibition signal measurement. Furthermore, the presence of common coexisting interfering species showed a minor change in signals (<4.4%). The developed sensor has been applied in the determination of malathion in spiked vegetable extracts. It exhibited promising results in term of fast and sensitive determination of malathion in real samples at trace level with recoveries of 91.0 to 104.4%. (RSDs < 5%, n?=?3). A comparison of the two studied techniques showed that the HPLC technique is unable to detect malathion when the concentration is lower than 1.8?µM while 0.006 µM is detected with appropriate RSDs 0.2–5.2% (n?=?3) by amperometric method. Due to the high sensitivity and selectivity, this new electrochemical sensor will be useful for monitoring trace malathion in real samples.     

Microwave extraction of incurred salinomycin from chicken tissues

Abstract

A rapid, accurate, environmentally friendly and cost‐effective microwave extraction technique was developed for the extraction of spiked and incurred salmomycin from chicken tissues (kidney, liver, muscle, ovarian yolk and fat). Extraction of salinomycin from various tissues was achieved by irradiating the sample in absolute ethanol and 2‐propanol (15+2) for 9 sec. in a common household microwave oven. The extract was analysed without further cleanup by HPLC on a C₁₈ column (5 μm) and detected at 592 nm via post‐column reaction with 4‐dimethylaminobenzaldehyde (DMABA) in a heated reactor coil at 86° C. Recoveries of salinomycin from spiked tissues at 30 ng/g level ranged between 87 and 100%. The limit of quantitation was found to be 10 ng/g. The developed method was applied for the analysis of incurred tissues and ovarian yolk of laying chickens given sodium salinomycin in feed at different levels for 14 consecutive days followed by withdrawal periods. Residues were detected in all tissues and ovarian yolk at 0 withdrawal time but declined during the withdrawal period. Highest residue were found in fat and ovarian yolk.     

Spatial and seasonal variations in atrazine and metolachlor surface water concentrations in Ontario (Canada) using ELISA

Concerns regarding the impacts of pesticides on aquatic species and drinking water sources have increased demands on water quality monitoring programs; however the costs of sample analysis can be prohibitive. In this study we investigated enzyme-linked immunosorbent assay (ELISA) as a cost-effective, high through-put method for measuring pesticide concentrations in surface waters. Seven hundred and thirty-nine samples from 158 locations throughout Ontario were analysed for atrazine and metolachlor from April to October 2007. Concentrations ranged from <0.1 to 3.91 μg L⁻¹ (median = 0.12 μg L⁻¹) for atrazine and from <0.1 to 1.83 μg L⁻¹ (median = 0.09 μg L⁻¹) for metolachlor. Peak concentrations occurred in late spring/early summer, in rural agricultural locations, and decreased over the remainder of the growing season for both herbicides. About 3% of the samples that had ELISA results occurring above the limit of quantification (0.10 μg L⁻¹) were evaluated against gas chromatography-mass spectrometry (GC-MS). Linear regression analysis revealed a R² value of 0.88 and 0.39, for atrazine and metolachlor, respectively. ELISA tended to overestimate concentrations for atrazine and metolachlor, most likely because the ELISA kits also detect their metabolites. Atrazine data suggest that ELISA may be used complementary with GC-MS analysis to enhance the spatial and temporal resolution of a water quality monitoring study. The commercially available metolachlor ELISA kit requires further investigation. ELISA may be used to detect atrazine and metolachlor in surface water samples, but it is not recommended as a quantitative replacement for traditional analytical methods.     

Multiresidue analysis of organophosphate and pyrethroid pesticides in duplicate-diet solid food by pressurized liquid extraction

An analytical method was developed for determining organophosphate pesticides (OPP) and pyrethroid pesticides (PYR) in duplicate-diet solid food. The method consisted of pressurized liquid extraction (PLE) with dichloromethane followed by cleanup with gel permeation and solid phase extraction columns and gas chromatography/mass spectrometry (GC/MS) analysis. Quantitative recoveries (73–117 %) of the target pesticides were obtained for spiked duplicate-diet food samples. The percent standard deviation (% RSD) of replicate food samples was within ± 20 %. Another method was developed for determining a common OPP metabolite, 3, 5, 6-trichloro-2-pyridinol (TCP) in duplicate-diet food. The method consisted of a PLE with methanol followed by liquid-liquid partitioning, derivatization, and GC/MS analysis. Recoveries of TCP ranged from 83 to 101 % for spiked duplicate-diet food samples. The % RSD of replicate food samples was within ± 15 %. The results confirmed that these methods are reliable and robust, and that they can be used in routine analysis. In addition, a storage stability study for a common OPP, chlorpyrifos (CPF), in solid food samples was performed. The fortified ¹⁵N-¹³C-labeled CPF was stable over 16 mo storage at ?20° C in the dark. The developed analytical methods were successfully applied to 278 duplicate-diet food samples from preschool children, demonstrating that these methods are robust and suitable for routine analysis in future exposure monitoring studies.     

Simultaneous determination of imidacloprid, thiacloprid, and thiamethoxam in soil and water by high-performance liquid chromatography with diode-array detection

A high-performance liquid chromatography method with diode-array detection (HPLC-DAD) is described for the determination of three neonicotinoid insecticides imidacloprid, thiacloprid, and thiamethoxam in soil and water. The soil samples were extracted with acetonitrile, while the water samples were extracted using C18 cartridges. The mean recoveries plus standard deviations for spiked soil samples were 82 +/- 4.2% for thiamethoxam, 99 +/- 4.2% for imidacloprid and 94 +/- 1.4% for thiacloprid. The recoveries for water samples ranged from 87 +/- 3.4% for thiamethoxam to 97 +/- 3.9% for imidacloprid and 97 +/- 2.6% for thiacloprid. The limits of quantitation (LOQ) were 0.1, 0.1, 0.01 mg/kg in soil (5g), and 2, 2, 0.5, micro/L in water (50 mL) for thiamethoxam, imidacloprid, and thiacloprid, respectively.     

Multiresidue method for high-performance liquid chromatography determination of carbamate pesticides residues in tea samples

A multiresidue method was developed to determine 19 carbamate pesticides in tea samples. Optimizations of different parameters, such as the type of extraction solvents, clean-up cartridges, and elution solvents were carried out. The developed method used acetonitrile as extraction solvent, amino cartridge for adsorbents and acetone-n-hexane as the eluting solution. Nineteen carbamate residues were then analyzed by high-pressure liquid chromatography (HPLC) with fluorescence detector. The present results showed good linearity by correlation coefficients of more than 0.9999 for all analyses. Limits of detection and quantification varied from 0.0005–0.023 mg L^{? 1}, 0.008–0.077 mg L^{? 1}, respectively. Recoveries of sixteen carbamate pesticides ranged from 65% to 135% at the spiked level of 0.5, 1.0 and 2.0 mg L^{? 1}. The relative standard deviations were lower than 20% and coefficient of variations were lower than 15%. The results indicate that the proposed method provides an effective multi and trace level screening determination of carbamate pesticides residues for tea samples.     

Matrix effects in analysis of dialkyl phosphate metabolites of organophosphate pesticides in urine by gas chromatography/tandem mass spectrometer

Urinary dialkyl phosphate metabolites (DAPs) are used as biomarkers to evaluate human exposure to organophosphate pesticides. The objective was to evaluate potential artifacts in urinary DAPs analysis during sample preparation and method calibration. Diluted urine pools were commonly used to prepare calibration standards to minimize the effects due to the complexity of urine matrix. Matrix effects on measurements of DAPs were evaluated by spiking known amount of standards into distilled water, synthetic urine and diluted urine pool. Different matrices resulted in similar concentrations detected for all target compounds, except dimethylphosphate (DMP) with the deviation of measurement as large as eight times the spiked amount. In this study, we also found that urinary particles, which usually appeared after thawing frozen human urine samples, could affect the measurements of DAPs, especially DMP and diethylthiophosphate (DETP). Results of DAPs measurements in three types of sample matrices, i.e. urine without particles, urine with particles and particles only were compared. DETP could be subject to large error during this preparation step. The use of deuterated and ¹³C₁₂-labeled DAPs as internal standards is also evaluated. Overall, these issues can cause misidentification and inaccuracies, which may significantly affect the data quality.