A statistical model for predicting carbon monoxide levels

This paper presents a statistical model that is able to predict carbon monoxide (CO) concentrations as a function of meteorological conditions and various air quality parameters. The experimental work was conducted in an urban atmosphere, where the emissions from cars are prevalent. A mobile air pollution monitoring laboratory was used to collect data, which were divided into two groups: a development group and a testing group. Only the development dataset was used for developing the model. The model was determined by using a stepwise multiple regression modelling procedure. Thirteen independent variables were selected as inputs: non-methane hydrocarbon (NMHC), methane (CH₄), suspended dust, carbon dioxide (CO₂), nitrogen oxide (NO), nitrogen dioxide (NO₂), sulfur dioxide (SO₂), ozone (O₃), wind speed, wind direction, temperature, relative humidity and solar energy. It was found that NO has the most effect on the predicted CO concentration. The contribution of NO to the CO concentration variations was 91.3%. Adding in the terms for NO₂), NMHC and CH₄ improved the model by only a further 2.3%. The derived model was shown to be statistically significant, and model predictions and experimental observations were shown to be consistent.     

Sustainable urban transportation: impact of CO2 mitigation strategies on local pollutants

This paper assesses CO₂ mitigation strategies in Delhi and Mumbai against the dynamics of local pollutants. After testing against techno-economic feasibility, compressed natural gas (CNG) technology, four-stroke two-wheelers and battery-operated vehicles (BOV) were selected as candidate options for Mumbai and Delhi. Multiple constrained optimisation for finding out the optimal mix of vehicles to meet the travel demand under the business-as-usual scenario for the period of CO₂ mitigation targets of 5, 10, 15, 20, 25% resulted in reduced stock of diesel and petrol vehicles, with the reduction spanning over different points of the above time period. In the case of Mumbai, battery-operated three-wheelers dominated the vehicular mix, with the share of CNG vehicles remaining at a standard level. CO₂ reduction targets did not influence the CNG option significantly. CO₂ mitigation influenced the dynamics of local pollutants considerably in both Delhi and Mumbai. In Delhi, TSP and SOx reduction levels against the CO₂ mitigation target were found to be significant. In Mumbai, the percentage reduction in local pollution (TSP in particular) was higher than the target CO₂ reduction. Local pollutants other than TSP and SO_x showed an increasing trend against the CO₂ mitigation strategies in Delhi. In the case of Mumbai, all non-target pollutants showed a falling trend against the CO₂ mitigation strategies, though insignificantly for pollutants other than TSP and SO_x.     

Analysis and interpretation of the monitoring data for C2–C11 hydrocarbons in the atmosphere of a rural Portuguese site

This paper focuses the application of a measurement technique for determining atmospheric C₂–C₆ hydrocarbons after canister sampling and analysis by gas chromatography/flame ionisation detection (GC/FID), as well of an adsorption-sampling technique for C₆–C₁₁ compounds and GC/FID analysis after thermal desorption and cryogenic concentration. Tens of samples collected at Giesta, a rural area located 20 km to the SE of the coastal Portuguese city of Aveiro, were analysed. The characterisation of C₂ C₁₁ hydrocarbons is presented, considering seasonal variations, diurnal cycles, the influence of air masses and different photochemical conditions. Ratios between hydrocarbons and principal components analysis were applied to differentiate between biogenic and anthropogenic sources.     

Exploratory study of some potential environmental impacts of CO2 sequestration in unmineable coal seams

An initial investigation into the potential environmental impacts of CO₂ sequestration in unmineable coal seams has been conducted, focusing on changes in the produced water during enhanced coalbed methane (ECBM) production, using a CO₂ injection process (CO₂-ECBM). A high volatile bituminous coal, Pittsburgh No. 8, was reacted with synthetic produced water and gaseous carbon dioxide at 40°C and 50 bar to evaluate the potential for mobilisation of toxic metals during CO₂-ECBM/sequestration. Microscopic and X-ray diffraction analysis of the post-reaction coal samples clearly show evidence of chemical reaction and chemical analysis of the synthetic produced water shows substantial changes in composition. These results suggest that changes to the produced water chemistry and the potential for mobilising toxic trace elements from coal beds are important factors to be considered when evaluating deep, unmineable coal seams for CO₂ sequestration.     

Air pollution at the Bily Kriz mountains in the Czech Republic

An evaluation of air pollution at the Bily Kriz mountains in the Czech Republic is given. Annual daily concentrations of sulphur dioxide (SO₂), nitrogen oxides (NO_x), particulate matter of size 10 mm (PM₁₀) and ozone (O₃) measured in the years 1994–2000 are presented. Air pollution at Bily Kriz is assessed with the reference to the European Union Directives and the standards adopted by the Czech Republic. In general, the concentrations of air pollutants were lower in 1996 for ozone and decreased for SO₂, NO_x and PM₁₀ from 1994. The daily values of SO₂ and PM₁₀ exceeded the European Union limits in approximately 0.0% and 5.5% of cases, respectively. The values of ozone exceeded the limits for the considered period.     

Changing consumption patterns and CO2 reduction

Today, most countries are facing national CO₂ targets focused on production and direct energy use. However, two important driving forces are increased consumption and changing consumption patterns. In this paper, we analyse the impact from household consumption on CO₂ emissions. Household energy use is taken into account, as is the consumption of commodities and services produced by industry. Based on Danish data, we estimate the CO₂ impact from different commodities. Further, we analyse the impact of changes in commodity mix in Danish household consumption in the period from 1966 to 1992. The results show that the change in commodity mix has been insufficient to compensate for the overall growth in Danish consumption. Further, we see that the consumption of food is a main contributor to overall Danish CO₂ emissions.     

Measurement of atmospheric particles and anionic species across central Taiwan

The ambient air concentrations and fluxes of various anionic species were sampled by MOUDI, TSP and dry deposition plates at a traffic sampling site in Taichung, central Taiwan. In the sampling period, from September to December 2000, the ambient air particle concentrations (PM₁, PM_2.5, PM₁₀ and TSP) were lower in the September than in the other three months (October to December). The reason is that the northwest wind brought more particles (diameter less than 10 μm) and the higher wind speed caused higher dry deposition fluxes and TSP concentrations in the last three months. The anion species percentages of TSP were 0.24%, 13.7%, 0.52%, 12.0%, 18.9'% and 54.6% for F^-, Cl^-, Br^-, NO₂^-, NO₃^- and SO₄^2-, respectively. The results revealed that SO₄^2-, NO₃^-, Cl^- and NO₂^- were the dominant species at the traffic sampling site. The ion-size distributions of Cl^-, NO₂^- and NO₃^- were unimodal, the main peak being between 3.2 and 5.6 μm. In contrast, the size distribution of SO₄^2- was bimodal, with the main peaks in the particle size ranges 0.32.0.56 μm and 3.2.5.6 μm. The ambient average particle dry deposition flux was 6.28 μg/m2/s, and the dry deposition fluxes were 0.01, 94.6, 0.05, 34.7, 72.2 and 376.4 ng/m2/s for F^-, Cl^-, Br^-, NO₂^-, NO₃^- and SO₄^2-, respectively. The dry deposition velocities were 3.10, 0.03, 3.67, 0.05, 1.54, 2.03 and 3.67 cm/s for F^-, Cl^-, Br^-, NO₂^-, NO₃^- and SO₄^2-, respectively.     

The application of the RAINS model for Greece

In order to comply in 2010 with the emission ceilings proposed by European commission under the convention on transboundary air pollution, Greece has to develop and implement a cohesive strategy affecting all the sectors of the economy. The RAINS model was used for the evaluation of the environmental and economic impacts arising from the use of a number of control technologies under alternative energy scenarios. To this purpose a number of modifications regarding the input databases of RAINS were made. The analysis clearly reveals that the reduction of SO₂ emissions can be achieved in a lower cost compared to the reduction of NO_x emissions. Moreover, the complementarity of CO₂ abatement policies and the SO₂/NO_x abatement policies is also accented.     

Limited provision of roads as a bottleneck on vehicle CO2 emissions in Asia: an international comparison of national trends

This paper explores the relationship between road infrastructure, economic growth and road CO₂ emissions. The basic premise is that many developing nations have achieved sufficient wealth to generate substantial demand for road vehicles, but that actual use is constrained by limited provision of surfaced roads. Our main result is that for comparable levels of income (GDP/capita), CO₂ emissions per length of paved road are far higher in rapidly developing Asia as compared to the USA. These findings suggest existence of an 'infrastructure bottleneck', that when relieved, may influence the future trajectory of road transport CO₂ emissions in developing Asia.     

Influence of meteorological factors on air pollution concentration for a coastal region in India

A long-term study of measurement of concentration of NO_x, SO₂ and TSP pollutants have been done in a port and harbour region in India. Monthly measurements of gaseous and particulate pollutants were made at six monitoring stations from January 1997 to December 2000. Meteorological data was also simultaneously collected. In this study, the relationship between monitored ambient air quality data and meteorological factors, such as wind speed, temperature, is statistically analysed, using the SPSS package. The monthly mean concentrations of NO_x, SO₂ and TSP were in the range of 19.5–59.0 μg/m3, 8.6–51.3 μg/m3 and 88.2–199.3 μg/m3, respectively. The results show that TSP is strongly correlated with NO_x and SO₂ with a correlation coefficient of 0.83 and 0.82, respectively. The correlation coefficients for TSP, NO_x, and SO₂ with wind are –0.78, –0.78, and –0.88, respectively.     

Separate determination of PM10 emission factors of road traffic for tailpipe emissions and emissions from abrasion and resuspension processes

Little is known about the relevance of mechanically produced particles of road traffic from abrasion and resuspension processes in relation to the exhaust pipe particles. In this paper, emission factors of PM₁₀ and PM₁ for light and heavy-duty vehicles were derived for different representative traffic regimes from concentration differences of particles and nitrogen oxides (NO_x) in ambient air upwind and downwind of busy roads, or alternatively of kerbsides and nearby background sites. Hereby, PM₁ was interpreted as direct exhaust emissions and PM₁₀-PM₁ as mechanically produced emissions from abrasion and resuspension processes. The results show that abrasion and resuspension processes represent a significant part of the total primary PM₁₀ emissions of road traffic. At sites with relatively undisturbed traffic flow they are in the same range as the exhaust pipe emissions. At sites with disturbed traffic flow due to traffic lights, emissions from abrasion/resuspension are even higher than those from the exhaust pipes.     

A structural decomposition analysis of air pollution from fossil fuel combustion in India

During the last decade, there has been worldwide concern with global climate change, which has been induced by greenhouse gases (GHGs) due to the use of fossil fuels. The CO₂ emissions from fossil fuel combustion have been identified as the single most significant source of GHG emissions into the atmosphere. Realising the need to control and regulate emissions of pollutants, the objective of the present study estimates the trend of CO₂, SO₂ and NO_x between the periods 1991-92 and 1996-97. An input-output structural decomposition analysis approach is used to determine their sources of change. It also provides a set of alternative scenarios for the year 2001-2 and 2006-7. The sources of changes in the amount of CO₂, SO₂ and NO_x emissions are categorised into four factors: the ecoefficiency, the structure of production, the structure of demand, and the volume of demand. Results indicate that the electricity sector contributes more towards direct, as well as indirect, emission coefficients. The petroleum product sector also contributes more in this respect. The dominant role is played by the structure of demand and the volume of demand.     

Nitrification of centrate from dewatering of anaerobically digested sludge

Nitrification of anaerobically digested sludge centrate was studied in bench-scale suspended growth and fixed film enhanced suspended growth systems at temperatures of 10.5-28.5°C and pH values of 6.0-9.1. Nitrification followed zero-order kinetics in both systems, and ammonia removals in excess of 99% were observed. The temperature dependency of the suspended growth nitrification rate observed under not fully acclimated biomass conditions at pH between 6.8 and 8.5, was expressed as k_T = k₂₀θ^T-20where k₂₀ and θ were found to be 0.34 mg NH₃-N/MLVSS-d and 1.033, respectively. The nitrification rate in the fixed film enhanced suspended growth system involving styrofoam pads ranged from 0.11 to 0.13 mg NH₃-N/mg MLVSS-d at temperatures of 21.5-25°C and pH values of 7.8-8.6. The process contained suspended solids in the range of 10-20 mg/l.     

Air pollution and the influence of sources on Paulinia (Brazil) and surroundings

The air quality in the industrial area and surroundings of the city of Paulinia (state of Sao Paulo, Brazil) has been investigated by analysing the concentration of air pollutants (SO₂, PM₁₀, NO, NO₂, CO and ozone) and identifying the main sources of air pollution. A mobile pollutant monitoring unit was used to collect the data at five different sites from November 2000 to July 2002. Critical pollutants were determined based on air quality standards, and sources were identified by principal component analysis. Photochemical reactions play an important role in Paulinia's air pollution: three out of five monitored sites showed levels exceeding the standard air quality of ozone. SO₂ and PM₁₀ appeared as pollutants deserving special attention. All the monitored sites showed vehicles and industrial plants (which release SO₂) to be significant sources of pollution. Depending on the location, ozone was related mainly with vehicular or industrial sources.     

Monitoring of phytoplankton biomass and nutrients in a polluted stream

The spatial and temporal variations in the concentrations of nutrients (NH₄⁺, NO₂⁻, PO₄³⁻, SiO₄⁻) and chlorophyll a were monitored simultaneously in a slow-flowing watercourse (Saricay Stream, Turkey), which runs in a rural–urban gradient. Chlorophyll a concentrations ranged between 0.044 μg l^-1 and 206.15 μg l^-1 and, in general, the higher concentrations of chlorophyll a and ammonium were measured downstream of the raw sewage outfalls. Nitrate was by far the most abundant form of inorganic nitrogen, and its concentration ranged between 411.71 μM and 87.25 μM. Silicates and phosphates were always potentially limiting to biomass relative to nitrogen. Agricultural run-off and point discharges from urban sources greatly affected the chemical composition of the water in the Saricay Stream and drove the system towards eutrophication.     

Treatment of reactive dyes and textile finishing wastewater using Fenton's oxidation for reuse

Fenton's oxidation (FO) was used to decolourise and degrade some reactive dyes (Remazol Black 5, Remazol Red, Remazol Blue, Remazol Yellow) and raw textile finishing industry effluents (S1, S2, S3) containing mainly reactive dyes. The operational conditions for pH varied between 2.5 and 4.0 while temperature ranged from 30°C to 50°C. The concentrations of FeSO₄ and H₂O₂ varied to a wide range (200–600 mg/l of FeSO₄, 300–1000 mg/l of H₂O₂) depending on the type of the dyes and their mixture and textile additives used in the process. FO is highly effective for colour removal (>99%) for reactive dyes and (87–94%) for textile finishing wastewater. It can be applied as a pretreatment and the remaining total dissolved solids (TDS) can be removed by an additional advanced process, e.g. membrane process.     

Sampling errors in the study of acid gases and anion species in atmospheric aerosols

Atmospheric acid aerosols were sampled by two annular denuder systems (ADS) and a micro-orifice uniform deposit impactor (MOUDI) at a traffic site in central Taiwan. Theoretical analysis showed that the relative artifact for HNO₃ gas sampling was about 0.53 when the initial HNO₃ concentration was under 0.2 µg/m³ and should be considered carefully. The concentrations of gaseous acid at the traffic sampling site were higher than those in the other study. The size distributions of acid aerosols were unimodal for Cl^-, NO₂^-, and NO₃^-, and bimodal for SO₄^2-. The dominant acid ions in particles less than 18 µm were SO₄^2-, NO₃^-, NO₂^- and Cl^-.     

Spatial and diurnal variations in concentration of atmospheric NOx along urban-rural roadways in Nanjing, Southeastern China

Atmospheric NO_x concentrations (including NO₂ and NO) on the roadside environments of urban trunk, belt highway and suburban road as well as a reference in a forest area were measured. NO_x concentrations on roadside environments tended to be higher than that on the reference. With the exception of suburban road, NO_x concentrations over both of the urban trunk and belt highway exceeded the limited value of National Air Environmental Quality Standards. Gradient measurement of NO_x on the downwind side of the belt highway shows that it declined to background level over 100 m from the road edge.     

Studies of air quality predictors based on neural networks

In recent years, urban air pollution has emerged as an acute problem because of its negative effect on health and living conditions. Regional air quality problems, in general, are linked to violations of specified air quality standards. The current study aims to find neural network based air quality predictors, which can work with a limited number of datasets and are robust enough to handle data with noise and errors. A number of available variations of neural network models, such as the Recurrent Network Model (RNM), the Change Point Detection Model with RNM (CPDM), the Sequential Network Construction Model (SNCM), the Self Organising Feature Model (SOFM), and the Moving Window Model (MWM), were implemented using MATLAB software for predicting air quality. Developed models were run to simulate and forecast based on the annual average data for 15 years from 1985 to 1999 for seven parameters, viz. VOC, NO_x, CO, SO₂, PM₁₀, PM_2.5 and NH₃ for one county of California, USA. The models were fitted with first nine years of data to predict data for remaining six years. The models, in general, could predict air quality patterns with modest accuracy. However, the SOFM model performed extremely well in comparison with the other models for predicting long-term (annual) data.     

Roadside particulate levels at 30 locations in the Kathmandu Valley, Nepal

Roadside particulate levels (PM₁₀) at 30 locations throughout the Kathmandu Valley, Nepal are reported. There were seven sampling cycles from January to December 1999. PM₁₀ levels ranged between 1000 and 6000 μ/m3 for 1-h sampling. There was no consistent trend in PM10 levels with respect to monitoring cycle, average precipitation or wind speed. There is no WHO guideline for PM₁₀ (no safe exposure threshold), but the EPA 24-h standard is 150 μ/m3. The major sources of roadside PM₁₀ include dust re-suspension from vehicular movement and human activity, and particulate emissions from old vehicles. Other sources of PM₁₀ in the valley include cement and brick factories. Studies are currently being conducted to determine the lead content of PM₁₀ from roadside samples. Additional studies are warranted to assess the potential adverse human health effects of acute or chronic exposure to high particulate levels reported in this study.