酸性洗涤塔-生物滤塔-生物曝气池组合工艺处理恶臭气体NH3和H2S

采用酸性洗涤塔、生物滤塔和生物曝气池的组合工艺处理NH3、H2S恶臭混合气体,研究表明,该组合工艺对NH3和H2S有很好的去除效果,在进气流量为35 L/min,喷淋量45 L/h时,NH3进气浓度50.15~525.4 mg/m3,H2S进气浓度10.23~110.36 mg/m3时,NH3单一进气去除率稳定在99%以上,H2S单一进气去除率90%以上。混合进气后,NH3去除率几乎为100%,H2S的去除率提高至98%以上。在一定的浓度范围内,NH3和H2S之间的相互作用对两者的去除效果没有明显的影响,而且起到了相互促进降解的作用。同时,进气流量和填料层高度都会影响NH3、H2S的去除率。系统对进气容积负荷变化的缓冲能力强,在偶尔超负荷条件下运行并不能使系统崩溃,并且微生物对高负荷逐渐表现出适应性。大部分溶于水的氨由生物曝气池去除,去除率达到96.9%。     

光催化与生物技术联用工艺处理油漆废气中试研究

光催化与生物技术联用工艺用于油漆生产、加工过程有机废气的现场处理,中试实验结果表明:油漆生产、加工过程现场的主要污染物是甲苯、乙苯、间/对二甲苯和邻二甲苯等苯系物,浓度在27～55 mg/m3之间。单独使用光催化和微生物技术现场处理这些苯系物,其去除效率都不很高。虽然在中试开始阶段光催化对苯系物的平均去除效率达到了86.2%,在中试稳定期,光催化技术对苯系物的平均去除效率却只有67.6%,而生物滴滤床在成功挂膜之后对现场有机废气的平均去除效率也仅为67.5%。但是将这两种工艺联合使用之后,在中试稳定期该组合工艺对苯系物的平均去除效率可以达到99.2%。     

不同生物塔净化化纤污水场恶臭性能的比较

为了考察生物法治理污水处理场恶臭气体的实验效果,本研究采用生物滴滤、生物过滤和生物洗涤3种方法对某中石化公司化纤污水处理场4个恶臭气体挥发严重的污水池(生活污水提升池、氧化池、事故池和调节池)进行恶臭治理。实验结果表明,待生物塔稳定运行后,改变处理气量由0.1 m~3·h-1增大到0.2 m~3·h-1,相应的停留时间(EBRT)由172 s缩短到86 s,生物滴滤塔对甲醇、乙醇、环己烷和间-二甲苯这4种污染物的去除效率分别提升至96.80%、100.00%、92.15%和99.68%。此外,3台生物塔对于外界气温变化的适应性良好,但生物滴滤塔的压降始终未检出。根据小试实验结果,该化纤污水处理场恶臭的有效治理可以选用生物滴滤技术。     

生物过滤塔处理实验室废气

研究了生物过滤塔处理实验室排放的模拟混合废气,考察了反应器对苯、甲苯、二甲苯、乙醇、丙酮、乙酸乙酯和甲烷等废气的去除效果。运行结果表明,在设备稳定运行期间,进气中总挥发性有机物(TVOCs)的浓度为124～380 mg/m3,而出气浓度在10～40 mg/m3,去除效率保持在85%以上。实验室废气中的多种污染物在生物过滤塔中去除机理不同,亲水性污染物的去除效率高于疏水性污染物。通过系统关停后重启,污染物的去除效果在第2天就能恢复,这为生物过滤塔处理实验室废气过程的停运检修或者系统闲置提供了可行性。     

一种缺氧型生物滴滤塔对硫化氢去除的最佳反应条件

取自污水处理厂二沉池活性污泥载入生物滴滤塔中,与传统生物滴滤塔对比,考察了在缺氧条件下微生物对H2S的去除效率,最适工艺运行条件及影响因素,实验结果表明,最佳工艺运行条件:温度为30℃,pH 6.0,H2S入口浓度C1=1 000 mg/m3、C2=2 000 mg/m3、C3=3 000 mg/m3,对应的最适气体流量和循环液喷淋量分别为35～55 L/h、45 L/h、55L/h和20 L/h、40 L/h、50 L/h,该生物滴滤塔最高H2S负荷率可达6.9 g/(m3.h),具有较高的H2S去除效率,最适工艺运行条件的确定对实际大中型沼气发酵池净化配套系统具有一定的指导意义。     

ABR-生物滴滤池组合工艺处理农村生活污水

采用ABR-生物滴滤池组合工艺,研究在水力停留时间为3 d、滴滤池水力负荷为5 m3/（m2·d）的条件下,组合工艺对生活污水中主要污染物的去除效果、滴滤池内部污染物浓度变化和微生物的沿程分布规律。实验结果表明,组合工艺对COD、TN、NH＋4-N和TP的平均去除率分别可达73%、32%、58%和30%;滴滤池内各层污染物浓度除TP在中层略有升高外,其余均沿程逐渐降低。滴滤池底层对各种污染物的去除能力均较强,原因是果壳活性炭填料较强的截留吸附能力以及底层微生物优势菌属较好的降解作用。总氮的去除依靠滴滤池内填料的物理化学作用和微生物同步硝化反硝化作用,其中微生物作用约占60%,成为脱氮的主要途径。     

印染废水高标准排放组合工艺优化

为了实现印染废水的高标准排放,构建了生物吸附/MBBR/混凝沉淀池/硫铁自养反硝化/活性焦组合工艺,并对其进行了优化运行研究;考察了不同水力停留时间(HRT)和溶解氧(DO)对系统污染物去除的影响。结果表明:生物吸附池和MBBR池的HRT分别为1 h和10 h、DO分别为1 mg·L~(-1)和5 mg·L~(-1)的情况下,污染物的去除效果最佳;其中,COD的去除率达到98%;在最优条件下,组合工艺出水COD、NH4+-N、TP和TN浓度分别为16、0.56、0.32和1.39 mg·L~(-1),污水色度基本完全去除。该组合工艺实现了印染废水的高标准排放,为印染废水处理的工程应用提供了数据和技术支撑。     

生物滴滤塔烟气同时脱硫脱硝中试动力学模拟

动力学模型可计算并预测各种操作参数条件下生物滴滤塔烟气同时脱硫脱硝工艺的运行效果。在实验室研究中建立了生物滴滤塔对SO_2及NO_x的降解去除动力学方程,并应用于中试试验研究。结果表明,在实验室研究中,生物滴滤塔对SO_2降解去除的动力学方程为c_(g,out)+32.052 8lnc_(g,out)=c_(g,in)+32.052 8lnc_(g,in)-90.158 7(c_(g,in)、c_(g,out)分别为进入生物滴滤塔底部、生物滴滤塔排出尾气中的气态SO_2或NO_x质量浓度,g/m~3,下同),对NO_x降解去除的动力学方程为c_(g,out)+8.223 7lnc_(g,out)=c_(g,in)+8.223 7lnc_(g,in)-8.284 1。中试试验研究中经过修正,生物滴滤塔对SO_2降解去除的动力学方程为c_(g,out)+3 105.685 5lnc_(g,out)=c_(g,in)+3 105.685 5lnc_(g,in)-11 126.837 3,对NO_x降解去除的动力学方程为c_(g,out)-916.675 2lnc_(g,out)=c_(g,in)-916.675 2lnc_(g,in)-244.226 2。     

O_3-BAC组合工艺深度净化MBR出水的中试研究

采用臭氧-生物活性炭（O3-BAC）组合工艺对某工业园区再生水厂MBR出水进行了深度净化的中试研究,主要考察了组合工艺各节点对常规指标的处理效果。结果表明,臭氧投加量约3 mg/L（H2O）、臭氧接触塔接触时间为30min、活性炭滤池空床接触时间（BECT）为15 min时,O3-BAC组合工艺能有效去除水中色度、浊度,平均色度和浊度分别从21度和7.8 NTU降至3度和2.0 NTU以下;组合工艺对UV254、高锰酸盐指数的平均去除率分别约为39%和35%;对NH4＋-N有一定的去除,去除率为58%～77%;组合工艺对粪大肠菌群去除效果显著,平均去除率在95%以上。O3-BAC组合工艺是一种有效工业园区再生水深度净化技术。     

生物滴滤塔处理H_2S臭气

目前,环保政策极其关注污水处理厂的臭气排放并制定了排放标准。本实验依托3个并联的中试生物滴滤塔对污水提升泵站的H2S臭气展开研究,考察不同H2S进气负荷、停留时间、压降和填料填装方式(竹炭-陶粒分层填装、完全混合及全竹炭填装)等因素对H2S去除率的影响。对生物滴滤塔的出气浓度、滤出液p H、SO2-4离子等进行测试分析,建立传质、降解动力学模型,并分析。在停留时间为25 s连续进气条件下,考察进气负荷在0.59~5.00 g H2S/(m3·h)范围内生物滴滤塔对H2S臭气的去除表现效果。研究结果表明,各生物滴滤塔的去除率(RE)都维持在98%以上,而且出气浓度达到厂界废气排放三级标准;相较于完全混合填装方式,分层填装在去除H2S臭气时略显优势。采用Michaelis-Menten方程描述生物滴滤塔的去除表现,表观半饱和常数Ks和最大表观去除速率Vm分别为5.92 m L/m3和5.84 g H2S/(m3·h)。     

Ethylbenzene removal in a multiple-stage biofilter

In practice, biofilters are often conceived as entire, single-unit systems. However, the activity of a biofilter varies greatly over its depth. For a given period, each stage of the biofilter dominates ethylbenzene removal. Ethylbenzene was continuously removed in a mixed-medium biofilter. The overall removal efficiency of the ethylbenzene ranged from 70% to greater than 99%. In the upflow biofilter, the most dominant ethylbenzene degrading stage shifted consecutively from the bottom to the top of the reactor. Average water content throughout the biofilter media was relatively consistent. However, the water content of each stage fluctuated dramatically and was correlated with the ethylbenzene removal rate. Without any water addition, the biofilter was operated for 62 days above the target removal efficiency of 80%. A 9-month slow-release fertilizer, mixed with composting media, was an effective way to eliminate the nutrient deficiency in the biofilter operation.     

Ethylbenzene Removal in a Multiple-Stage Biofilter

ABSTRACT

In practice, biofilters are often conceived as entire, single-unit systems. However, the activity of a biofilter varies greatly over its depth. For a given period, each stage of the biofilter dominates ethylbenzene removal. Ethylbenzene was continuously removed in a mixed-medium biofilter. The overall removal efficiency of the ethylbenzene ranged from 70% to greater than 99%. In the upflow biofilter, the most dominant ethylbenzene degrading stage shifted consecutively from the bottom to the top of the reactor. Average water content throughout the biofilter media was relatively consistent. However, the water content of each stage fluctuated dramatically and was correlated with the ethylbenzene removal rate. Without any water addition, the biofilter was operated for 62 days above the target removal efficiency of 80%. A 9-month slow-release fertilizer, mixed with composting media, was an effective way to eliminate the nutrient deficiency in the biofilter operation.     

复合生物滤池处理H2S和NH3的挂膜与工艺条件

采用复合生物滤池(生物滴滤池 生物过滤池)处理H2S和NH3组成的混合恶臭气体,填料分别为经表面改性的天然斜发沸石和木屑.实验研究了该工艺的驯化挂膜情况和主要工艺条件,结果表明,天然斜发沸石和木屑改性后,驯化挂膜周期为10～14 d,比文献中颗粒活性炭挂膜缩短14～18 d.复合生物滤池的最佳工艺条件为:高度120 cm,循环液流量4.56 L/h.同时,生物滴滤池处理水溶性好的NH3气体效果较生物过滤池好,而生物过滤池处理水溶性差的H2S气体较生物滴滤池好.因此,复合生物滤池可用于处理不同水溶性的混合恶臭气体.     

A hybrid biological process of indoor air treatment for toluene removal

Bioprocesses, such as biofiltration, are commonly used to treat industrial effluents containing volatile organic compounds (VOCs) at low concentrations. Nevertheless, the use of biofiltration for indoor air pollution (IAP) treatment requires adjustments depending on specific indoor environments. Therefore, this study focuses on the convenience of a hybrid biological process for IAP treatment. A biofiltration reactor using a green waste compost was combined with an adsorption column filled with activated carbon (AC). This system treated a toluene-micropolluted effluent (concentration between 17 and 52 µg/m³), exhibiting concentration peaks close to 733 µg/m³ for a few hours per day. High removal efficiency was obtained despite changes in toluene inlet load (from 4.2 × 10^?3 to 0.20 g/m³/hr), which proves the hybrid system’s effectiveness. In fact, during unexpected concentration changes, the efficiency of the biofilter is greatly decreased, but the adsorption column maintains the high efficiency of the entire process (removal efficiency [RE] close to 100%). Moreover, the adsorption column after biofiltration is able to deal with the problem of the emission of particles and/or microorganisms from the biofilter.

ImplicationsIndoor air pollution is nowadays recognized as a major environmental and health issue. This original study investigates the performance of a hybrid biological process combining a biofilter and an adsorption column for removal of indoor VOCs, specifically toluene.     

Effect of Advanced Oxidants Generated Via Ultraviolet Light on a Sequentially Loaded and Regenerated Granular Activated Carbon Biofilter

Abstract

The objective of this research was to investigate a sequentially loaded and regenerated granular activated carbon (GAC) biofilter system and to determine whether regenerative ozonation/advanced oxidation could improve the removal and biodegradation of a volatile organic compound from a contaminated airstream. Bench-scale reactors were constructed to operate in a manner analogous to a commercially available system manufactured by Terr-Aqua Environmental Systems (only with longer contact time). The GAC system consisted of two GAC biofilter beds that operated in a cyclical manner. On a given day, the first GAC bed adsorbed methyl isobutyl ketone from a simulated waste airstream, while the second bed underwent regeneration; then on the next day, the second bed was in the adsorption mode while the first was regenerated.

Three bench-scale systems were used to compare the performance under three operating conditions: (1) ozone/ associated oxidant regeneration of a GAC biofilter system that was seeded with microorganisms from a field site, (2) a humid air regeneration of a seeded GAC biofilter, and (3) a humid air regeneration of an unseeded GAC biofilter. For the advanced oxidant regenerated GAC biofilter, a maximum removal efficiency of >95% was achieved with an empty bed contact time of 148 sec and an influent concentration of 125 ppm methyl isobutyl ketone, and 90–95% was achieved at 148-sec empty bed contact time and a 1150-ppm influent.     

Two-stage biofilter for effective NH3 removal from waste gases containing high concentrations of H2S

A high H2S concentration inhibits nitrification when H2S and NH3 are simultaneously treated in a single biofilter. To improve NH3 removal from waste gases containing concentrated H2S, a two-stage biofilter was designed to solve the problem. In this study, the first biofilter, inoculated with Thiobacillus thioparus, was intended mainly to remove H2S and to reduce the effect of H2S concentration on nitrification in the second biofilter, and the second biofilter, inoculated with Nitrosomonas europaea, was to remove NH3. Extensive studies, which took into account the characteristics of gas removal, the engineering properties of the two biofilters, and biological parameters, were conducted in a 210-day operation. The results showed that an average 98% removal efficiency for H2S and a 100% removal efficiency for NH3 (empty bed retention time = 23-180 sec) were achieved after 70 days. The maximum degradation rate for NH3 was measured as 2.35 g N day(-1) kg of dry granular activated carbon(-1). Inhibition of nitrification was not found in the biofilter. This two-stage biofilter also exhibited good adaptability to shock loading and shutdown periods. Analysis of metabolic product and observation of the bacterial community revealed no obvious acidification or alkalinity phenomena. In addition, a lower moisture content (approximately 40%) for microbial survival and low pressure drop (average 24.39 mm H2O m(-1)) for system operation demonstrated that the two-stage biofilter was energy saving and economic. Thus, the two-stage biofilter is a feasible system to enhance NH3 removal in the concentrated coexistence of H2S.     

Removal of ammonia by biofilters: a study with flow-modified system and kinetics

The characteristics of ammonia removal by two types of biofilter (a standard biofilter with vertical gas flow and a modified biofilter with horizontal gas flow) were investigated. A mixture of organic materials such as compost, bark, and peat was used as the biofilter media based on the small-scale column test for media selection. Complete removal capacity, defined as the maximum inlet load of ammonia that was completely removed, was obtained. The modified biofilter showed complete removal up to 1.0 g N/kg dry material/day. However, the removal capacity of the standard biofilter started to deviate from complete removal around 0.4 g N/kg dry material/day, indicating that the modified biofilter system has higher removal efficiency than the standard upflow one. In kinetic analysis of the biological removal of ammonia in each biofilter system, the maximum removal rate, Vm, was 0.93 g N/kg dry material/day and the saturation constant, Ks, was 32.55 ppm in the standard biofilter. On the other hand, the values of Vm and Ks were 1.66 g N/kg dry material/day and 74.25 ppm, respectively, in the modified biofilter system.     

Fe~Ⅱ（EDTA）协同生物转鼓过滤器去除NO的实验研究

采用自行研制的生物转鼓反应器（RDB）处理难溶于水的NO废气,为提高NO的传质系数和去除效率,实验考察了营养液中添加FeⅡ（EDTA）络合剂协同RDB以提高NO去除效率的过程。结果表明,当空床停留时间（EBRT）为0.96 min时,在营养液中添加FeⅡ（EDTA）至100 mg/L后,NO的去除效率从70.78%升至79.26%。未添加FeⅡ（EDTA）时NO去除率随营养液的增加下降,添加FeⅡ（EDTA）至100 mg/L后,去除率随营养液量的增加先上升后下降,且下降速率比上升速率大。随着营养液中FeⅡ（EDTA）浓度从0增加至500 mg/L,实验最佳温度从32.5℃升至47.5℃,但添加FeⅡ（ED-TA）至100 mg/L对实验的最适pH值没有太大影响。     

Development and performance of an alternative biofilter system

Step tracer tests were carried out on lab-scale biofilters to determine the residence time distributions (RTDs) of gases passing through two types of biofilters: a standard biofilter with vertical gas flow and a modified biofilter with horizontal gas flow. Results were used to define the flow patterns in the reactors. "Non-ideal flow" indicates that the flow reactors did not behave like either type of ideal reactor: the perfectly stirred reactor [often called a "continuously stirred tank reactor" (CSTR)] or the plug-flow reactor. The horizontal biofilter with back-mixing was able to accommodate a shorter residence time without the usual requirement of greater biofilter surface area for increased biofiltration efficiency. Experimental results indicated that the first bed of the modified biofilter behaved like two CSTRs in series, while the second bed may be represented by two or three CSTRs in series. Because of the flow baffles used in the horizontal biofilter system, its performance was more similar to completely mixed systems, and hence, it could not be modeled as a plug-flow reactor. For the standard biofilter, the number of CSTRs was found to be between 2 and 9 depending on the airflow rate. In terms of NH3 removal efficiency and elimination capacity, the standard biofilter was not as good as the modified system; moreover, the second bed of the modified biofilter exhibited greater removal efficiency than the first bed. The elimination rate increased as biofilter load increased. An opposite trend was exhibited with respect to removal efficiency.     

Removal of low concentrations of carbon tetrachloride in compost-based biofilters operated under methanogenic conditions.

Research was performed to demonstrate the removal of carbon tetrachloride (CT) using compost biofilters operated under methanogenic conditions. Biofilters were operated at an empty-bed residence time of 2.8 minutes using nitrogen as the atmosphere. Hydrogen and carbon dioxide were supplied as an electron donor and carbon source, respectively, during acclimation of the bed medium microbes. Once methanogenesis was demonstrated, CT flow to the biofilter was established. Biofilters were operated over a CT concentration range from 20 to 700 ppbv for 6 months. Bed medium microbes were able to remove up to 75% of the inlet CT. At excessively high CT concentrations (> 500 ppmv), methane production and hydrogen utilization by the bed medium microbes appeared to be inhibited. CT removal by the biofilter decreased when the hydrogen supply was removed from the biofilter inlet, indicating that hydrogen acted as the electron donor for reductive dechlorination. The removal efficiency and relatively low empty bed residence times demonstrated by these laboratory-scale biofilters indicate that anaerobic biofiltration of CT may be a feasible full-scale process.