"十二五"城镇污水处理厂环保投资效益分析

根据2011—2015年环境统计数据,分析了"十二五"期间城镇污水处理厂固定资产投资、环保投资效益等相关情况。研究发现,中国城镇污水处理厂在"十二五"期间固定资产投资和运行费用不断增加,污水处理能力不断提升,到2015年底,城镇污水处理厂共计5 390座,污水处理能力达17 169万t/d,实际污水处理量达到498.7亿t/a,COD和氨氮的去除量分别达到1 136.8万t和115.8万t。通过分析目前城镇污水处理厂在投资建设、运行维护等方面存在的问题,提出了相关建议,对今后城镇污水处理厂建设及运行起到指导作用。     

城镇污水处理厂用地、运行及建设费用研究

汇总收集了国内已建城镇污水处理厂的大量资料,分析探讨了污水处理厂厂区占地面积、运行及建设费用与处理规模之间的关系,为今后污水处理厂的设计规划、工艺选择、建设费用分析等提供参考依据。研究表明污水处理厂厂区占地面积与处理规模可用函数表示,且具有较高的相关性。城镇污水处理厂所选用的工艺和处理规模对其运行成本有较大的影响,分别对大中小规模的污水处理厂在不同工艺下的运行成本进行分析,得出大规模污水处理厂的工艺选择对其运行成本影响不大;中规模污水处理厂易采用氧化沟工艺;小规模的污水处理厂适合采用SBR工艺。建设费用与污水处理规模有密切关系,由于建设费用受多种因素影响,又以江浙地区为例,对其建设费用与污水处理规模之间关系进行具体分析,对以上结论给予一定的补充。     

广西城镇污水处理厂建设和运行的现状分析

全区108座污水处理厂建设规模、工艺、投资和运行成本统计表明,广西城镇污水处理厂以小型污水处理厂为主,处理工艺多采用氧化沟、A2/O、SBR及其变种工艺;5～10万m3/d规模污水处理单位建设投资以氧化沟、A2/O、SBR及其变种工艺较省,2～5万m3/d规模以氧化沟、MSBR工艺较省,2 m3/d以下规模以硅藻土、人工湿地和人工快渗工艺较为经济;2～10万m3/d规模污水处理厂各工艺运行成本多介于0.3～0.4元/m3,2万m3/d以下规模人工快渗和人工湿地工艺的运行费用介于0.2～0.3元/m3。不同规模、不同工艺、不同排放标准污水处理厂的投资建设、运行成本和出水水质各异,因此,污水处理厂应因地制宜选择适宜工艺技术、规模及排放标准,有效提高设施运行负荷率和污染物的去除率。     

贵州省已建城镇污水处理厂建设及运行状况

"十一五"期间,贵州省开展了大规模的城镇污水处理厂建设,主要采用了以氧化沟、A/O工艺和SBR及改良工艺等具有脱氮除磷功能、技术成熟的工艺,建设规模多在0.5万m3/d以下,单位平均建设投资4 069.75元/m3,单位综合能耗平均0.35 k Wh/m3,单位平均药耗0.41 g/m3,单位运行成本多在0.60元/m3以上,污水平均处理率82.01%,平均处理负荷率73.19%,处理出水基本达到城镇污水处理厂污染物排放标准(GB18918-2002)一级B标准的要求,取得了较好的减排效果,但部分污水处理厂存在工艺技术的匹配性等问题,建议"十二五"期间加强已建污水处理厂工艺技术和设施的改造升级。     

城镇污水处理厂的综合绩效评价

近年来我国城镇污水处理厂的修建得到很大发展,但其在运行管理方面存在一些问题,为了促进污水处理厂的稳定运行与升级改造,需要建立一套综合绩效评价体系对其进行科学的评价与管理。在对城镇污水处理厂的调查研究基础上,提出将DPSIR原理融入到城镇污水处理厂综合绩效评价指标体系的构造中,形成了一个3层19个指标的综合绩效评价指标体系,通过层次分析法(AHP)和模糊综合评价法相结合,创建了城镇污水处理厂综合绩效的AHP-模糊综合评价模型,并选取成都市两座(A和B)城镇污水处理厂展开实例应用研究。结果表明:A污水处理厂综合绩效评价结果有26.3%隶属于"较好"等级,B污水处理厂综合绩效评价结果有28.1%隶属于"一般"等级。根据最大隶属度原则,A和B污水处理厂综合绩效评价等级分别属于"较好"和"一般"。     

连锁控制的A~2/O-MBR工艺处理石化社区生活污水

采用连锁控制的A2/O-MBR工艺处理石化社区低浓度的生活污水并回用,处理规模520 m3/h。工程运行监测结果表明,该工艺对低浓度生活污水处理效果良好,出水水质达到了《城镇污水处理厂污染物排放标准》(GB18918-2002)的一级B标准和《污水再生利用工程设计规范》(GB50335-2002)标准要求。通过连锁控制,系统运行稳定,具有较强的耐冲击负荷能力,实现了污水处理厂正常运行。     

中国城镇污水处理厂运行状况调查分析

根据问卷调查资料和抽样监测数据,分析了中国城镇污水处理厂的工艺水平、实际运行负荷、水质稳定性以及剩余污泥处理处置等方面的现状与问题.通过调查分析可知,近年来,中国的城镇污水处理事业得到了前所未有的发展,但城镇污水处理工作中也存在着一些明显不足,其主要表现为:(1)由于配套管网建设滞后和运行费用不足等问题,导致实际污水处理量未能与污水处理能力保持同步增长.近1/3数量的污水处理厂的运行负荷率低于70%,造成1/4以上的污水处理能力被闲置.(2)污水处理厂出水水质的稳定性普遍不高,一些传统的处理工艺则更差.(3)污泥不经脱水即随意外运、乱弃的现象已有很大改观,但绝大部分污泥都未经稳定化处理,更为严重的是仍有少部分污泥无任何处置措施.     

浙江标准下的城镇污水处理厂提质增效管理对策研究

在浙江地方标准《城镇污水处理厂主要水污染物排放标准》(DB33/2169—2018)发布实施的背景下，全面调查了浙江城镇污水处理厂设计规模、处理工艺、进水来源、水质特征等，从进水角度识别了城镇污水处理厂达标排放需要关注的问题。从提升管网效能、实施进水管控、加强运维保障等方面，提出了城镇污水处理厂提质增效管理对策建议，研究结果对城镇污水处理厂污染减排具有重要意义。     

美国某污水处理厂工艺设计及运行效果

介绍了美国某污水处理厂的处理工艺流程、主要构筑物构成及其设计参数,通过对该污水处理厂一年内运行效果的调研,分析评价了该污水厂的进出水水质指标；该水厂工艺流程对TSS、BOD5、COD、NH3-N、TP和浊度的年平均去除率分别可以达到97.7％、97.7％、93.5％、82.6％、95.2％和97.9％,各项出水水质均优于我国《城镇污水处理厂污染物排放标准》(GB18918-2002)一级A标准,通过对该水厂工艺的介绍和分析,为我国污水厂的建设及改造升级提供了一定的参考依据.     

城镇污水处理厂生物除臭技术的关键影响因素及案例分析

城镇污水处理厂运行中产生恶臭气体并因此导致空气污染的问题日益严重.生物除臭技术具有操作简便、运行成本低、二次污染小等优点,适用于污水处理厂恶臭气体的处理.阐述了污水处理厂臭气的主要成分、浓度及分布特点,分析了生物除臭技术的4个关键影响因素(微生物、营养液、pH和填料),并结合影响因素剖析了3个工程应用典型案例,总结了生...     

城市污水处理厂的自动控制设计要点

通过一个城市污水处理厂自动控制系统的选取与设汁过程作为实例,说明了可编程逻辑控制器(PLC)自动控制方案是当今城市污水处理厂的最佳选择。论文对PLC自动控制方案的设计过程提出了详细的指导,将基于PLC的生产过程自动化与办公自动化进行了有机结合,为大型污水处理厂自动化控制设计提供了极重要的借鉴。     

污水处理工程--两段式活性污泥工艺

我国中小城市的污水处理通常有如下特点(1 )工业废水所占比重较大,甚至超过50 %,致使要处理的城市污水的污染物浓度较高,污染物负荷变化较大 ;(2)城市财政状况比较紧张,可用于建设污水处理厂的资金有限.两段式活性污泥工艺是对传统活性污泥工艺的改进,在好氧处理之前采用一个缺氧或厌氧段,用于有机物的水解酸化或生物除磷.两段式工艺有以下优点处理效率高、工程投资和日常运行费用低,更适合我国国情.本文以两个工程项目为例,论述了两段式活性污泥工艺的工程设计与实际应用.山东省招远市污水处理厂于1999年7月投入运行,处理后排放水中的污染物指标低于设计值.蓬莱市污水处理厂工程即将竣工,设计处理能力20000m3 /d,工程总投资约1200万元,远远低于目前国内的平均水平.     

Phosphorus removal from municipal wastewater by hydrous ferric oxide reactive filtration and coupled chemically enhanced secondary treatment: part I--performance.

This work examines the performance of a hydrous ferric oxide (HFO) reactive filtration (RF) process with coupled chemically enhanced secondary treatment (RECYCLE) for phosphorus removal from municipal wastewater (HFO-RF-RECYCLE). A 3-month, 0.95-ML/d (0.25-mgd) demonstration of HFO-RF-RECYCLE was performed at a municipal wastewater treatment plant equipped with oxidation ditches and secondary clarifiers. Influent to the plant averaged 6.0 mg/L phosphorus, with a tertiary effluent average of 0.011 mg/L phosphorus. Iron doses to the plant were low, at 5 mg/L. Inline recycling of HFO solution rejects to the plant influent resulted in a maximum 90.3%, dose-dependent reduction of phosphorus in the secondary effluent at 4.5 ML/d (1.2 mgd). Other results included reduction of total suspended solids and turbidity. A mass balance analysis was performed. We conclude that HFO-RF-RECYCLE may allow very low levels of phosphorus discharge from municipal wastewater treatment plants with a ferric-iron-based tertiary filtration process and residual recycling.     

城市污水处理厂除臭技术

介绍了城市污水处理厂臭气来源、成分及产量.针对目前国内外除臭技术的研究和发展情况,分析了污水处理厂的各种物理、化学和生物除臭方法的技术原理、优缺点和应用现状.结合日本城市污水处理厂的运行实际,重点介绍了一种不产生臭气的新技术--腐殖活性污泥法的工艺流程、特点及其应用现状.     

A rational procedure for estimation of greenhouse-gas emissions from municipal wastewater treatment plants.

Municipal wastewater treatment may lead to the emission of greenhouse gases. The current Intergovenmental Panel on Climate Change (Geneva, Switzerland) approach attributes only methane emissions to wastewater treatment, but this approach may overestimate greenhouse gas emissions from the highly aerobic processes primarily used in North America. To better estimate greenhouse gas emissions, a procedure is developed that can be used either with plant-specific data or more general regional data. The procedure was evaluated using full-scale data from 16 Canadian wastewater treatment facilities and then applied to all 10 Canadian provinces. The principal greenhouse gas emitted from municipal wastewater treatment plants was estimated to be carbon dioxide (CO2), with very little methane expected. The emission rates ranged from 0.005 kg CO2-equivalent/m3 treated for primary treatment facilities to 0.26 kg CO2-equivalent/m3 for conventional activated sludge, with anaerobic sludge digestion to over 0.8 kg CO2-equivalent/m3 for extended aeration with aerobic digestion. Increasing the effectiveness of biogas generation and use will decrease the greenhouse gas emissions that may be assigned to the wastewater treatment plant.     

Chemical composition associated with different particle size fractions in municipal, industrial, and agricultural wastewaters

A more detailed characterization of particulate organic matter in wastewater streams is needed to improve solid-liquid separation and biological processes for wastewater treatment. The objective of this paper was to evaluate particle size distributions and the associated chemical composition for municipal, industrial, and agricultural waste streams. Most of the organic matter in these wastewaters was larger than a molecular weight of 10(3) amu and therefore would require extracellular hydrolysis before any bacterial metabolism. Particle size distributions were significantly different for the studied waste streams. In municipal wastewater, the organic matter was evenly distributed in all eight size fractions ranging from 10(3) amu up to 63 microm. The industrial and agricultural wastewaters, however, contained mainly soluble organic matter (<10(3) amu) and larger particles (>1.2 microm for the industrial and >10 microm for the agricultural waste) leaving a gap in the size range of large macromolecules and colloids. The relative protein and carbohydrate concentrations varied for the different size fractions compared to the measured chemical oxygen demand (COD) in the corresponding size fraction. Thus, the design of the solid-liquid separation at a treatment plant could be used to purposefully modify the overall chemical composition of the organic matter before further biological treatment. Particle size distributions will influence design and operation of biological nutrient removal processes such as denitrification or biological phosphorus removal that may be carbon limited if a large fraction of the organic matter is composed of large particles with slow hydrolysis rates. Measured particle size distributions for the different waste streams in this study (municipal, industrial, agricultural) were significantly different requiring specific approaches for treatment plant design.     

城市污水处理厂除臭技术

介绍了城市污水处理厂臭气来源、成分及产量。针对目前国内外除臭技术的研究和发展情况，分析了污水处理厂的各种物理、化学和生物除臭方法的技术原理、优缺点和应用现状。结合日本城市污水处理厂的运行实际，重点介绍了一种不产生臭气的新技术——腐殖活性污泥法的工艺流程、特点及其应用现状。     

微絮凝-直接过滤工艺在城市污水深度处理中的应用研究

微絮凝 -直接过滤工艺是一种将混凝反应、沉淀截留集中在同一滤柱内同步完成的高效水处理工艺。该工艺应用于城市污水的深度处理中 ,通过絮凝剂的加入 ,具有同步去除PO3 -4 P、SS和部分COD的功能。本文研究了该工艺对二级处理出水中PO3 -4 P、SS和COD的去除效果及其规律。研究表明 :采用聚合氯化铁 (PFC)作为絮凝剂 ,当Fe/P摩尔比为 2∶1时 ,水中PO3 -4 P的去除率达 98.8% ,浓度可降至 0 .1mg/L以下 ,同时SS、COD去除率也有明显提高。与传统的混凝、沉淀除磷工艺相比 ,该工艺具有操作简单、结构紧凑、占地面积小、污泥量少等优点 ,是一种更为经济和简单的处理单元 ,适用于现有城市污水处理厂的除磷和进一步提高水质的深度处理     

Anaerobic codigestion of municipal, farm, and industrial organic wastes: a survey of recent literature.

Codigestion of organic wastes is a technology that is increasingly being applied for simultaneous treatment of several solid and liquid organic wastes. The main advantages of this technology are improved methane yield because of the supply of additional nutrients from the codigestates and more efficient use of equipment and cost-sharing by processing multiple waste streams in a single facility. Many municipal wastewater treatment plants (WWTPs) in industrialized countries currently process wastewater sludge in large digesters. Codigestion of organic wastes with municipal wastewater sludge can increase digester gas production and provide savings in the overall energy costs of plant operations. Methane recovery also helps to reduce the emission of greenhouse gases to the atmosphere. The goal of this literature survey was to summarize the research conducted in the last four years on anaerobic codigestion to identify applications of codigestion at WWTPs. Because the solids content in municipal wastewater sludge is low, this survey only focuses on codigestion processes operated at relative low solids content (slurry mode). Semi-solid or solid codigestion processes were not included. Municipal wastewater sludge, the organic fraction of municipal solid waste, and cattle manure (CAM) are the main wastes most often used in codigestion processes. Wastes that are codigested with these main wastes are wood wastes, industrial organic wastes, and farm wastes. These are referred to in this survey as codigestates. The literature provides many laboratory studies (batch assays and bench-scale digesters) that assess the digestibility of codigestates and evaluate the performance and monitoring of codigestion, inhibition of digestion by codigestates, the design of the process (e.g., single-stage or two-stage processes), and the operation temperature (e.g., mesophilic or thermophilic). Only a few reports on pilot- and full-scale studies were found. These evaluate general process performance and pretreatment of codigestates, energy production, and treatment costs.