Controllable synthesis Fe3O4@POHABA core-shell nanostructure as high-performance recyclable bifunctional magnetic antimicrobial agent

We demonstrated a method to form magnetic antimicrobial POHABA (poly-N,N′-[(4,5-dihydroxy-1,2-phenylene)bis(methylene)]bisacrylamide)-based core-shell nanostructure by free-radical polymerization of OHABA on the Fe₃O₄ core surface. The magnetic antimicrobial agent Fe₃O₄@POHABA can be used in domestic water treatment against bacterial pathogens. The thickness of POHABA shell could be controlled from 10.4 ± 1.2 to 56.3 ± 11.7 nm by the dosage of OHABA. The results of antimicrobial-activity test indicated that POHABA-based core-shell nanostructure had broad-spectrum inhibitory against Gram-negative, Gram-positive bacteria and fungi. The minimum inhibitory concentration (MIC) values of Fe₃O₄@POHABA nanostructure against Escherichia coli and Bacillus subtilis were both 0.4 mg/mL. Fe₃O₄@POHABA nanostructures responded to a permanent magnet and were easily recycled. Fe₃O₄@POHABA nanoparticles retained 100% antimicrobial efficiency for both Gram-negative and Gram-positive bacteria throughout eight recycle procedures.

     

Physicochemical characterisation of diesel exhaust particles: Factors for assessing biological activity

A range of microscopy and analytical techniques have been used to investigate the physicochemical properties of diluted DEP that may be important in determining its biological activity. Transmission electron microscopy demonstrated four basic categories of particle morphology: (1) “spherulites” [individual particles]; (2) “chains” or “clusters” of spherulites; (3) “spherules”, [large bodies of spherulites]; (4) “flake-like bodies”. Image analysis of TEM photomicrographs determined empirical morphological parameters (30 nm mean spherulite diameter, aspect ratio 1.5, mean particle area 0.078 μm, equivalent spherical diameter 0.23 μm, roundness 2.76) and derived parameters (0.313 μm² surface area, 3.7 μm² pg surface area per mass and 0.042 μm³ volume) of DEP. Distributions of the particle sizes by number showed 10.1% were ultrafine (<0.1 μm), 89.5% fine (0.1–2.0 μm), 0.4% coarse (>2.5 μm), but distributions based on a mass value were different (0.01% ultrafine; 52.6% fine, 47.4% coarse). In contrast, impacted DEP contained 60.87% ultrafine, 39.13% fine and 0% coarse particles by number. Field emission scanning electron microscopy of spherulites revealed smooth surfaces and flocculated spherules with large surface areas. Electron probe X-ray micro-analysis demonstrated the presence of C, O, Na, Mg, K, Al, Si, P, S, Cl, Ca along with a range of metals (Ti, Mn, Fe, Zn, Cr), that were heterogeneous in distribution. Inductively coupled plasma mass and atomic emission spectrometry identified Mg, P, Ca, Cr, Mn, Zn, Sr, Mo, Ba, Na, Fe, S, and Si as the mobile sorbed metals readily removed during sonication in water from DEP suspensions. X-ray Diffraction confirmed previous observations of the presence of nanometer sized crystallites of disordered graphite. Comparison of microscopy and analytical results between sonicated and impacted DEP revealed a physicochemical difference that must be taken into account in any toxicological investigations.     

The effect of γ-Fe2O3 nanoparticles on Escherichia coli genome

Extensive production and application of γ-Fe₂O₃ magnetic nanoparticles (MNPs) has increased their potential risk on environment and human health. This report illustrates a genetic impact of γ-Fe₂O₃ magnetic nanoparticles (MNPs) on Escherichia coli (E. coli). After 3000-generation incubation with MNPs addition, obvious genomic variations were revealed by using repetitive extragenic palindromic PCR (rep-PCR) DNA fingerprint technique. The physicochemical interactions between MNPs and bacteria could be responsible for such genomic responses. It was revealed that Fe³⁺ concentration increased in the medium. Transmission electronic microscopy (TEM) and flow cytometry (FCM) analysis consistently demonstrated the occurrences of adsorption and membranes-internalization of MNPs outside and inside cells. Both increased Fe³⁺ ion and the uptake of MNPs facilitated Fe binding with proteins and DNA strands, resulting in enhancing the mutation frequency of E. coli. Our results would be of great help to assessing the potential impact of MNPs on human and environment.     

磁性埃洛石对水溶液中盐酸土霉素的吸附

采用一种简便的方法对埃洛石纳米管进行加磁，得到的磁性埃洛石纳米管（MHNTs）利用x射线衍射仪（XRD）、透射电子显微镜（TEM）、振动样品磁强计（VSM）和原子吸收光谱仪（AAS）进行表征，结果表明，MHNTs具有很强的磁性性能（Ms=34．02emu／g）以及较低损失磁性粒子的性能。制备的MHNTs作为吸附剂吸附水溶液中的盐酸土霉素，并且探索反应温度、溶液pH和起始浓度等对MHNTs吸附盐酸土霉素性能的影响。研究表明，Langmuir等温线模型更优于Freundlich等温线模型，其动力学的研究结果利用拟二阶方程能够很好地进行说明。此外，MHNTs作为吸附剂经过3次的重复使用吸附能力没有明显的降低。     

Clearance and recovery of Cd(II) from aqueous solution by magnetic separation technology

An effective method to actualize the recycling use of Cd(II) in industrial wastewater was developed by using the magnetic beads, which was modified with ethylenediamine. When the industrial wastewater was treated with these magnetic beads, the Cd(II) concentration in the solution was sharply reduced to the governmental standard (0.1 μg mL⁻¹) of China. Based on the monolayer adsorption of Cd(II) on the surface of these magnetic beads, the saturation capacity for Cd(II) reached to 68 mg g⁻¹ dried magnetic beads. On the other hand, the binding Cd(II) could be easily recovered in acid conditions and the recovery efficiency exceeded 99%. Thus, in the process of the wastewater purification, the recycling utilization of Cd(II) was realized. Additionally, the excellent capability of regeneration and recycling utilization of these magnetic beads made this technology much suitable for the large-scale application. Compared with the conventional purification methods, the rapid process, simple equipments, easy operation and high efficiency, brought this technology with great potentialities in the treatment of industrial wastewater.     

Inputs and distributions of synthetic musk fragrances in an estuarine and coastal environment; a case study

Synthetic musks are ubiquitous contaminants in the environment. Compartmental distributions (dissolved, suspended particle associated and sedimentary) of the compounds throughout an axial estuarine transect and in coastal waters are reported. High concentrations of Galaxolide^® (HHCB) and Tonalide^® (AHTN) (987-2098 ng/L and 55-159 ng/L, respectively) were encountered in final effluent samples from sewage treatment plants (STPs) discharging into the Tamar and Plym Estuaries (UK), with lower concentrations of Celestolide^® (ADBI) (4-13 ng/L), Phantolide^® (AHMI) (6-9 ng/L), musk xylene (MX) (4-7 ng/L) and musk ketone (MK) (18-30 ng/L). Rapid dilution from the outfalls is demonstrated with resulting concentrations of HHCB spanning from 5 to 30 ng/L and those for AHTN from 3 to 15 ng/L. The other musks were generally not detected in the estuarine and coastal waters. The suspended particulate matter (SPM) and sedimentary profiles and compositions (HHCB:AHTN ratios) generally reflect the distribution in the water column with highest concentrations adjacent to sewage outfalls.     

Accumulation of free and covalently bound microcystins in tissues of Lymnaea stagnalis (Gastropoda) following toxic cyanobacteria or dissolved microcystin-LR exposure

Accumulation of free microcystins (MCs) in freshwater gastropods has been demonstrated but accumulation of MCs covalently bound to tissues has never been considered so far. Here, we follow the accumulation of total (free and bound) MCs in Lymnaea stagnalis exposed to i) dissolved MC-LR (33 and 100 μg L⁻¹) and ii) Planktothrix agardhii suspensions producing 5 and 33 μg MC-LR equivalents L⁻¹ over a 5-week period, and after a 3-week depuration period. Snails exposed to dissolved MC-LR accumulated up to 0.26 μg total MCs g⁻¹ dry weight (DW), with no detection of bound MCs. Snails exposed to MCs producing P. agardhii accumulated up to 69.9 μg total MCs g⁻¹ DW, of which from 17.7 to 66.7% were bound. After depuration, up to 15.3 μg g⁻¹ DW of bound MCs were detected in snails previously exposed to toxic cyanobacteria, representing a potential source of MCs transfer through the food web.     

Activated carbon/Fe(3)O(4) nanoparticle composite: fabrication, methyl orange removal and regeneration by hydrogen peroxide

In the water treatment field, activated carbons (ACs) have wide applications in adsorptions. However, the applications are limited by difficulties encountered in separation and regeneration processes. Here, activated carbon/Fe₃O₄ nanoparticle composites, which combine the adsorption features of powdered activated carbon (PAC) with the magnetic and excellent catalytic properties of Fe₃O₄ nanoparticles, were fabricated by a modified impregnation method using HNO₃ as the carbon modifying agent. The obtained composites were characterized by X-ray diffraction, scanning and transmission electron microscopy, nitrogen adsorption isotherms and vibrating sample magnetometer. Their performance for methyl orange (MO) removal by adsorption was evaluated. The regeneration of the composite and PAC-HNO₃ (powdered activated carbon modified by HNO₃) adsorbed MO by hydrogen peroxide was investigated. The composites had a high specific surface area and porosity and a superparamagnetic property that shows they can be manipulated by an external magnetic field. Adsorption experiments showed that the MO sorption process on the composites followed pseudo-second order kinetic model and the adsorption isotherm date could be simulated with both the Freundlich and Langmuir models. The regeneration indicated that the presence of the Fe₃O₄ nanoparticles is important for a achieving high regeneration efficiency by hydrogen peroxide.     

Magnetic molecularly imprinted polymer prepared by microwave heating for confirmatory determination of chloramphenicol in chicken feed using high-performance liquid chromatography-tandem mass spectrometry

Abstract

A magnetic molecularly imprinted polymer (MMIP) for chloramphenicol was prepared using a surface-imprinted and microwave-heating-induced polymerization method. The surfaces of the magnetic particles were first double-bond functionalized with 3-(trimethoxysilyl)propyl methacrylate (γ-MPS), followed by the copolymerization of 4-vinyl pyridine (4-VP) and trimethylolpropane trimethacrylate (TRIM) in the presence of chloramphenicol as a template and 1,1-azobis(cyclohexane-carbonitrile) (ABCN) as an initiator in a mixture of dimethyl sulfoxide and water with microwave heating at 80°C. The magnetic polymer possesses supraparamagnetic properties and was used to concentrate and cleanup chicken feed extract, followed by chromatographic separation using a Lichrospher®100 RP C8 column and detection with two multi-reaction monitoring transitions at m/z 321→ 152 and m/z 321→ 257. The mean recoveries obtained at two spiking levels were in the range of 94.6–100% The relative intra- and inter-day standard deviations were in the range of 1.4–2.6% and 5.1–5.7%, respectively. The detection limit of the method was 0.12 µg kg^?1. This confirmatory method was successfully applied to determine chloramphenicol in chicken feed samples.     

Simultaneous use of relaxed eddy accumulation and gradient flux techniques for the measurement of sea-to-air exchange of dimethyl sulphide

The sea-to-air flux of the biogenic volatile sulphur compound dimethyl sulphide was assessed with the relaxed eddy accumulation (REA) and the gradient flux (GF) techniques from a stationary platform in the coastal Atlantic Ocean. Fluxes varied between 2 and 16 μmol m⁻² d⁻¹. Fluxes derived from REA were on average 7.1±5.03 μmol m⁻² d⁻¹, not significantly different from the average flux of 5.3±2.3 μmol m⁻² d⁻¹ derived from GF measurements. Gas transfer velocities were calculated from the fluxes and seawater DMS concentrations. They were within the range of gas transfer rates derived from the commonly used parameterizations that relate gas transfer to wind speed.     

Distribution of perfluorochemicals between sera and milk from the same mothers and implications for prenatal and postnatal exposures

The levels of six perfluorocarboxylates (PFCAs), four perfloroalkylsulfonates (PFASs), and one sulfonamide were measured in paired samples of maternal serum, umbilical cord serum, and breast milk. The maternal and cord sera were strongly correlated with each other for all measured compounds (r > 0.5 and p < 0.01). Nevertheless, there was a significant difference in compound composition profile between the two sera matrices, with a more depletion of the longer chain compounds in cord serum. The transfer efficiency values from maternal to cord serum (TF_CS/MS) decreased by 70% with each increasing unit of -CF₂ chain within a PFCA group, and for perfluorooctanesulfonate (PFOS), by a half compared to perfluorooctanoate (PFOA). In contrast to the strong correlation in concentrations between the two sera matrices, the pattern of compounds in breast milk differed considerably with those in sera. Accordingly, compound- and matrix-specific transfer must be considered when assessing prenatal and postnatal exposure.     

Identification of magnetic particulates in road dust accumulated on roadside snow using magnetic, geochemical and micro-morphological analyses

The aim of this study is to test the applicability of snow surveying in the collection and detailed characterization of vehicle-derived magnetic particles. Road dust extracted from snow, collected near a busy urban highway and a low traffic road in a rural environment (southern Finland), was studied using magnetic, geochemical and micro-morphological analyses. Significant differences in horizontal distribution of mass specific magnetic susceptibility (χ) were noticed for both roads. Multi-domain (MD) magnetite was identified as the primary magnetic mineral. Scanning electron microscope (SEM) analyses of road dust from both roads revealed: (1) angular-shaped particles (diameter ∼1-300 μm) mostly composed of Fe, Cr and Ni, derived from circulation of motor vehicles and (2) iron-rich spherules (d ∼ 2-70 μm). Tungsten-rich particles (d < 2 μm), derived from tyre stud abrasion were also identified. Additionally, a decreasing trend in χ and selected trace elements was observed with increasing distance from the road edge.     

A laboratory study of the effect of NO2 on the atmospheric corrosion of zinc

Studies on the effect of NO_x on zinc corrosion are scarce and their results are variable and at times seemingly contradictory. This paper reports laboratory tests involving the dry deposition on zinc surfaces of 800 μg m⁻³ NO₂, alone and in combination with 800 μg m⁻³ SO₂, at temperatures of 35 and 25 °C and relative humidities of 90% and 70%. From the gravimetric results obtained and from the characterisation of the corrosion products by optical microscopy, scanning electron microscopy (SEM/EDX), grazing incidence X-ray diffraction (GIXD) and X-ray photoelectron spectroscopy (XPS), it has been verified that the corrosive action of NO₂ alone is negligible compared with SO₂. However, an accelerating effect has been observed when NO₂ acts in conjunction with SO₂ at 25 °C and 90% RH. At 35 °C and 90% RH, the accelerating effect is smaller, and at low relative humidities (70%), the synergistic effect is only slight, which suggests it may be favoured by the presence of moisture. In those cases where an accelerating effect has been observed, a greater proportion of sulphate ions has been found in the corrosion products, and nitrogen compounds have not been detected, indicating that NO₂ participates indirectly as a catalyst of the oxidation of SO₂ to sulphate.     

The potential effect of differential ambient and deployment chamber temperatures on PRC derived sampling rates with polyurethane foam (PUF) passive air samplers

Performance reference compound (PRC) derived sampling rates were determined for polyurethane foam (PUF) passive air samplers in both sub-tropical and temperate locations across Australia. These estimates were on average a factor of 2.7 times higher in summer than winter. The known effects of wind speed and temperature on mass transfer coefficients could not account for this observation. Sampling rates are often derived using ambient temperatures, not the actual temperatures within deployment chambers. If deployment chamber temperatures are in fact higher than ambient temperatures, estimated sampler-air partition coefficients would be greater than actual partition coefficients resulting in an overestimation of PRC derived sampling rates. Sampling rates determined under measured ambient temperatures and estimated deployment chamber temperatures in summer ranged from 7.1 to 10 m³ day⁻¹ and 2.2-6.8 m³ day⁻¹ respectively. These results suggest that potential differences between ambient and deployment chamber temperatures should be considered when deriving PRC-based sampling rates.     

Improved treatment approach for the removal of aromatic compounds using polymeric beads in Fenton pretreatment and biological oxidation

An improved approach based on the use of iron-doped polymeric beads (IPB) as Fenton catalyst in the pretreatment and biomass-doped polymeric bead (BPB) in the biological oxidation has been reported for the removal of different aromatic mixtures present as pollutants in the aqueous solutions. Degradation has been investigated at fixed loading of IPB as 2.5 % weight basis and varying loading of hydrogen peroxide so as to understand the effect of oxidant loading on the extent of degradation. It has been observed that the maximum removal efficiency as 75.5, 81.4, and 59.1 % was obtained for the benzene-toluene-naphthalene-xylene (BTNX), benzene-toluene-ethylbenzene-xylene (BTEX), and benzene-toluene-naphthalene-p-nitrophenol (BTNp-NP) mixtures, respectively, at a 40-min pretreatment and optimum pH of 3.5. The biodegradability index was also observed in the favorable range of 0.4 to 0.5 after the pretreatment at optimum H₂O₂ loading of 1.5 g L⁻¹. Maximum COD removal efficiency of 99.2, 99.3, and 99.6 % was obtained using the biological oxidation treatment for 40 h for the case of BTNX, BTEX, and BTNp-NP mixtures, respectively. Analysis of kinetic models revealed that degradation followed three distinct stages based on fitting of the three-stage model and BPB was found to be more efficient as compared to the primary activated sludge (PAS) and modified activated sludge (MAS). Reusability studies confirmed that both IPB and BPB were effective over many cycles giving stable performance during degradation without leaching of Fe³⁺ ions into the solution.

     

Preparation,characterization, and photocatalytic activity evaluation of Fe–N-codoped TiO2/fly ash cenospheres floating photocatalyst

Nitrogen-doped titanium dioxide (TiO₂) and Fe–N-codoped TiO₂ layers on fly ash cenospheres (FAC) as floating photocatalyst were successfully prepared through sol–gel method. Photocatalysts were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS), ultraviolet (UV)–Vis diffuse reflectance spectroscopy (DRS), and nitrogen adsorption analyses for Brunauer–Emmett–Teller (BET) specific surface area. Photocatalytic efficiency of the prepared catalyst was evaluated through using the decomposition of Rhodamine B (RhB) as a model compound under visible light irradiation. Photocatalytic activity and kinetics of catalyst under visible light were detected in details from different Fe/Ti mole ratios by detecting photodegradation of RhB. Experimental results show that when the calcination temperature was 550 °C, the dosage of FAC was 3.0 g, and the mole ratio of Fe/Ti was 0.71 %; the synthesized Fe–N-TiO₂/FAC photocatalyst presented as anatase phase and that N and Fe ions were doped into TiO₂ lattice. The material’s specific surface area was 34.027 m²/g, and UV–Vis diffuse reflectance spectroscopy shows that the edge of the photon absorption has been red shifted up to 400–500 nm. Fe–N-codoped titanium dioxide on FAC had excellent photocatalytic activity during the process of photodegradation of RhB under visible light irradiation.

     

Analysis of perfluoroalkyl carboxylates in vacuum cleaner dust samples in Japan

Perfluorooctanoic acid (PFOA) has long been an environmental contaminant of concern owing to its potential health risk. However, exposure to perfluorinated carboxylic acids (PFCAs) other than PFOA is not well understood. In this study, we investigated the concentrations of PFCAs in vacuum cleaner dust in Japan to measure the PFCAs contamination in an indoor environment. Most of the 77 samples contained PFCAs with 6–13 carbon atoms. The median concentration of perfluorononanoic acid (PFNA, 23.2 ng g⁻¹) was highest among PFCAs, followed by PFOA (20.8 ng g⁻¹) and perfluoroundecanoic acid (PFUnDA, 12.9 ng g⁻¹). The 90th percentile concentrations of PFNA, PFUnDA and perfluorotridecanoic acid (PFTrDA) were 948, 283 and 110 ng g⁻¹, respectively, and these were detected at greater concentrations than neighboring, even-numbered PFCAs. The proportion of long-chain PFCAs in vacuum cleaner dust from Japan was relatively higher than those reported for other countries. Factor analysis showed three independent factors. Odd-numbered long chain PFCAs (PFNA, PFUnDA and PFTrDA), which can correspond to factor 1, were major components of PFCAs in vacuum cleaner dust. Short chain PFCAs (factor 2) and even numbered long chain PFCAs (factor 3) were also statistically separated. These findings suggest that there are several sources of PFCAs with different origins in indoor environment. Further investigations into the origins of PFCAs are needed to evaluate indoor contamination with PFCAs.     

Measurements of ultrafine particles and other vehicular pollutants inside school buses in South Texas

Increasing evidence has demonstrated toxic effects of vehicular emitted ultrafine particles (UFPs, diameter < 100 nm), with the highest human exposure usually occurring on and near roadways. Children are particularly at risk due to immature respiratory systems and faster breathing rates. In this study, children’s exposure to in-cabin air pollutants, especially UFPs, was measured inside four diesel-powered school buses. Two 1990 and two 2006 model year diesel-powered school buses were selected to represent the age extremes of school buses in service. Each bus was driven on two routine bus runs to study school children’s exposure under different transportation conditions in South Texas. The number concentration and size distribution of UFPs, total particle number concentration, PM_2.5, PM₁₀, black carbon (BC), CO, and CO₂ levels were monitored inside the buses. The average total particle number concentrations observed inside the school buses ranged from 7.3 × 10³ to 3.4 × 10⁴ particles cm^?3, depending on engine age and window position. When the windows were closed, the in-cabin air pollutants were more likely due to the school buses’ self-pollution. The 1990 model year school buses demonstrated much higher air pollutant concentrations than the 2006 model year ones. When the windows were open, the majority of in-cabin air pollutants came from the outside roadway environment with similar pollutant levels observed regardless of engine ages. The highest average UFP concentration was observed at a bus transfer station where approximately 27 idling school buses were queued to load or unload students. Starting-up and idling generated higher air pollutant levels than the driving state. Higher in-cabin air pollutant concentrations were observed when more students were on board.     

A comparative evaluation of passive and active samplers for measurements of gaseous semi-volatile organic compounds in the tropical atmosphere

The polyurethane foam (PUF) disk-based passive air samplers (PAS), mounted inside two aluminium bowls to buffer the air flow to the disk and to shield it from precipitation and sunlight, were used for the collection of atmospheric SVOCs in Singapore during April 2008–June 2008. Data obtained from PAS measurements are compared to those from active high-volume air sampling (AAS). Single factor ANOVA tests show that there were no significant differences in chemical distribution profiles between actively and passively collected samples (PAHs, F = 3.38 × 10^?8 < F_critical = 4.17 with p > 0.05; OCPs, F = 2.71 × 10^?8 < F_critical = 4.75 with p > 0.05). The average air-side mass transfer coefficient (k_A) for PAS, determined from the loss of depuration compounds such as 13C₆ – HCB (1000 ng), 13C₁₂ – 4,4′ DDT (1000 ng) and 13C₁₂ – PCB 101 (1000 ng)spiked on the disks prior to deployment, was 0.12 ± 0.04 m s^?1. These values are comparable to those reported previously in the literature. The average sampling rate was 3.78 ± 1.83 m³ d^?1 for the 365 cm² PUF disk. Throughout the entire sampling period (～68 d), most of the PAHs and all OCPs exhibited a linear uptake trend on PAS, while naphthalene, acenaphthylene, acenaphthene and fluorene reached the curvilinear phase after the first ～30 d exposure. Theoretically estimated times to equilibrium (t_eq) ranged from around one month for Acy to hundreds of years for DB(ah)A. Sampling rates, based on the time integrated active sampling-derived concentrations and masses collected by PUF disks during the linear uptake phase, were determined for all target compounds with the average values of 2.50 m³ d^?1 and 3.43 m³ d^?1 for PAHs and OCPs, respectively. More variations were observed as compared to those from the depuration study. These variation were most likely due to the difference of physicochemical properties of individual species. Lastly, multiple linear regression models were developed to estimate the log-transformed gaseous concentration of an individual compound in air based on the mass collection rate of the gaseous SVOCs measured using the PAS and the molecular weight (MW) of the particular compound for both PAHs and OCPs, respectively.     

The relationships between mercury and selenium in plankton and fish from a tropical food web

Background, aim, and scope  Selenium (Se) has been shown to reduce mercury (Hg) bioavailability and trophic transfer in aquatic ecosystems. The study of methylmercury (MeHg) and Se bioaccumulation by plankton is therefore of great significance in order to obtain a better understanding of the estuarine processes concerning Hg and Se accumulation and biomagnification throughout the food web. In the western South Atlantic, few studies have documented trace element and MeHg in fish tissues. No previous study about trace elements and MeHg in plankton has been conducted concerning tropical marine food webs. Se, Hg, and MeHg were determined in two size classes of plankton, microplankton (70–290 μm) and mesoplankton (≥290 μm), and also in muscle tissues and livers of four fish species of different trophic levels (Mugil liza, a planktivorous fish; Bagre spp., an omnivorous fish; Micropogonias furnieri, a benthic carnivorous fish; and Centropomus undecimalis, a pelagic carnivorous fish) from a polluted estuary in the Brazilian Southeast coast, Guanabara Bay. Biological and ecological factors such as body length, feeding habits, and trophic transfer were considered in order to outline the relationships between these two elements. The differences in trace element levels among the different trophic levels were investigated. Materials and methods  Fish were collected from July 2004 to August 2005 at Guanabara Bay. Plankton was collected from six locations within the bay in August 2005. Total mercury (THg) was determined by cold vapor atomic absorption spectrometry (CV-AAS) with sodium borohydride as a reducing agent. MeHg analysis was conducted by digesting samples with an alcoholic potassium hydroxide solution followed by dithizone-toluene extraction. MeHg was then identified and quantified in the toluene layer by gas chromatography with an electron capture detector (GC-ECD). Se was determined by AAS using graphite tube with Pin platform and Zeeman background correction. Results and discussion  Total mercury, MeHg, and Se increased with plankton size class. THg and Se values were below 2.0 and 4.8 μg g⁻¹ dry wt in microplankton and mesoplankton, respectively. A large excess of molar concentrations of Se in relation to THg was observed in both plankton size class and both fish tissues. Plankton presented the lowest concentrations of this element. In fish, the liver showed the highest THg and Se concentrations. THg and Se in muscle were higher in Centropomus undecimalis (3.4 and 25.5 nmol g⁻¹) than in Micropogonias furnieri (2.9 and 15.3 nmol g⁻¹), Bagre spp (1.3 and 3.4 nmol g⁻¹) and Mugil liza (0.3 and 5.1 nmol g⁻¹), respectively. The trophic transfer of THg and Se was observed between trophic levels from prey (considering microplankton and mesoplankton) to top predator (fish). The top predators in this ecosystem, Centropomus undecimalis and Micropogonias furnieri, presented similar MeHg concentrations in muscles and liver. Microplankton presented lower ratios of methylmercury to total mercury concentration (MeHg/THg) (34%) than those found in mesoplankton (69%) and in the muscle of planktivorous fish, Mugil liza (56%). The other fish species presented similar MeHg/THg in muscle tissue (of around 100%). M. liza showed lower MeHg/THg in the liver than C. undecimalis (35%), M. furnieri (31%) and Bagre spp. (22%). Significant positive linear relationships were observed between the molar concentrations of THg and Se in the muscle tissue of M. furnieri and M. liza. These fish species also showed significant inverse linear relationships between hepatic MeHg and Se, suggesting a strong antagonistic effect of Se on MeHg assimilation and accumulation. Conclusions  Differences found among the concentrations THg, MeHg, and Se in microplankton, mesozooplankton, and fishes were probably related to the preferred prey and bioavailability of these elements in the marine environment. The increasing concentration of MeHg and Se at successively higher trophic levels of the food web of Guanabara Bay corresponds to a transfer between trophic levels from the lower trophic level to the top-level predator, suggesting that MeHg and Se were biomagnified throughout the food web. Hg and Se were positively correlated with the fish standard length, suggesting that larger and older fish bioaccumulated more of these trace elements. THg, MeHg, and Se were a function of the plankton size. Recommendations and perspectives  There is a need to assess the role of selenium in mercury accumulation in tropical ecosystems. Without further studies of the speciation of selenium in livers of fishes from this region, the precise role of this element, if any, cannot be verified in positively affecting mercury accumulation. Further studies of this element in the study of marine species should include liver samples containing relatively high concentrations of mercury. A basin-wide survey of selenium in fishes is also recommended.