Sorption of lead in soil as a function of pH: a study case in México

Reactions of lead sorption onto soil are largely affected by properties and composition of soil and its solution. In this study, the lead sorption onto regosol eutric soil from Francisco I. Madero, Zacatecas, Mexico is evaluated at different pH values. Soil samples were suspended in lead solutions of 10, 25, 50, 100, 150, 200, 300, and 400 mg/l (as Pb(NO3)2). The pH was adjusted at 2, 3, 4, and 5.5 with nitric acid for each of the lead solution concentrations. In all the cases the ionic strength was I=0.09 M with calcium nitrate. The solid-liquid-ratios were fixed in 1:100 and 1:200 g/ml. The results show that lead sorption increases when pH increases. Experimental isotherms were adjusted by both Langmuir and Freundlich models. The Langmuir affinity parameter, K, indicates that the lead sorption capacity of Francisco I. Madero soils is largely perceptible to pH changes.     

COVID-19: unbalanced management of occupational risks—case of the analysis of the chemical risk related to the use of disinfectants in the dairy industry in Morocco

Environmental Science and Pollution Research - Moroccan employers have a strong responsibility for the safety and health of their employees in the workplace and for protecting them from the risk of...     

Effects of anthropogenic activities on hydrochemical characteristics of ground water of Da’an irrigation area in Western of Jilin Province

Environmental Science and Pollution Research - The groundwater environment changes under the influence of anthropogenic activities. Because of the construction of the Da’an irrigation area,...     

Does digitalization matter in green preferences in nexus of output volatility and environmental quality?

Environmental Science and Pollution Research - The fact is that output volatility and carbon dioxide (CO2) emissions move together over the period. This empirical study examines the dynamic effect...     

Analyses of ozone in urban and rural sites in Málaga (Spain)

Ozone concentrations were measured at two (urban and a rural) sites near the city of Málaga (Spain). The aim of this study was to determine the daily, monthly and seasonal variation patterns of ozone concentrations at both sites and to study the possible regional influences. The daily variations mostly have the usual features with the afternoon maximum and the night minimum being more pronounced in the urban area. The average monthly concentrations throughout the year start to increase in March reaching their maximum values in July for the urban site. However, in the rural area, the monthly variations are smaller reaching their maximum value in June. The hourly evolution of the ozone concentrations in both sampling sites is well defined in spring and summer and not so well defined in autumn and winter. Taking into account the four seasons, the rural concentrations are higher than the urban ones. Summer is the season when there are similar concentrations at both sampling sites. Average hourly summer afternoon ozone for the hours 12:00-20:00 LST exceeded the 110 microg m(-3) European Union guidelines for human health for 8 h ozone exposure at the urban and rural sites.     

Annual and seasonal trends in chemical composition of precipitation in Japan during 1989–1998

Annual and seasonal trends were discussed for precipitation chemistry in Japan on the basis of a nationwide monitoring network by Japan Environment Agency. For this analysis, 17 sites, selected from the 23 network sites after evaluation of data completeness for the present purpose, were grouped into four areas in terms of the sea which could characterize each area: the Pacific Ocean, the Japan Sea, the Seto Inland Sea and the East China Sea areas. Major ion concentrations at each site were subjected to least-squares multiple regression analysis, and discussion was principally focused on the area-groups. Each area showed significant (p<0.05) decreasing trends in non-sea-salt sulfate (nss-SO₄²⁻) concentrations with the annual mean change rate of −3.0% yr⁻¹, whereas no significant trends were detected for NO₃⁻ at 59% of the sites. Ammonium (NH₄⁺) showed significant increasing trends for 35%, and decreasing trends for 18% of the sites; and, the maximum change rate of 3.8% yr⁻¹ was recorded in the Pacific Ocean area. Non-sea-salt calcium (nss-Ca²⁺) concentrations significantly decreased in northern and some industrialized areas. Both the annual cycle-amplitudes and effects of precipitation amounts were significant for the four ions at almost all sites. The maximum concentrations of nss-SO₄²⁻ and -Ca²⁺ occurred from winter to spring at most sites. The seasons when the maximum concentrations of NO₃⁻ and NH₄⁺ occurred, were found to differ from area to area. Furthermore, the trends in precipitation nss-SO₄²⁻, and NO₃⁻ were qualitatively consistent with those of anthropogenic emissions of SO₂, and NO_x in Japan, respectively.     

The temporal variability of the profile of carcinogenic polycyclic aromatic hydrocarbons in urban air: a study in a medium traffic area in Rome, 1993–1998

The constancy, both temporal and spatial, of the profile of polycyclic aromatic hydrocarbons (PAHs) relative to benzo[a]pyrene (BaP) is a prerequisite to using the BaP-indicator approach in the carcinogenic risk assessment for PAHs. The principal aim of this study was to provide a contribution to validate this approach, by studying the variability of the profile at a typical urban site through a multi-year data set and by comparing the profiles available for different cities. Seven carcinogenic PAHs (benz[a]anthracene, benzo[b+j+k]fluoranthenes, BaP, indeno[1,2,3-cd]pyrene, dibenz[a,h]anthracene) were determined in PM₁₀ 24-h samples collected every third day at a road site; moreover, benzo[e]pyrene was determined as a reference PAH due to its stability. The profile was found stable from year to year. Besides, it was similar to those recently found in other European cities (observed differences within a factor of four) and to those elaborated from earlier (1970s–1980s) investigations. The substantial similarity of profiles, both temporal (on an annual basis) and spatial, supports the validity of the BaP-indicator approach. Large PAH-to-PAH differences were, however, found in the seasonal pattern of profile: they were explained by the different atmospheric degradability of PAHs, whose effect is enhanced under the meteoclimatic conditions typical of the European Mediterranean countries. PAH annual means showed a slight declining trend since 1994. In the last sampling year, mean concentration of BaP was 1.2 ng m⁻³. Within-year differences among monthly averaged PAH concentrations were observed, as large as up to 44-fold for BaP, underlining the need for whole-year monitoring.     

Spatial variations in the aeolian deposition of dust – the effect of a city: a case study in Be'er-Sheva,Israel

The effect of buildings on the dry deposition of dust particles was investigated in Be'er-Sheva, a desert city with about 140,000 inhabitants in southern Israel, and at two reference points in the surrounding rural area. The mineral and chemical composition of dust sampled at all sites was similar, reflecting the composition of the local loess soil, its likely origin. However, dust deposited in the traps set up in the vicinity of buildings in the city was significantly coarser than the dust which accumulated in similar traps at exposed sites in the countryside. The amount of dust (by weight) in the urban dust traps was on an average more than twice the amount deposited in the rural area. The differences in grain-size distribution and quantity of dust are attributed to the properties of the urban wind field and to various effects of human activity in the city.     

Estimation of the exchange of sulphur pollution over the Balkan region in 1995–2000

The Bulgarian dispersion model 'Eulerian Model for Air Pollution' (EMAP) is used to estimate the sulphur pollution over the Balkan region for the period 1995–2000. A subdomain of the European Monitoring and Evaluation Programme (EMEP) grid is chosen containing 12 countries. The computational grid in this domain has a space step of 25 km, twice as fine as the EMEP grid. The former operational DWD 'Europa-Model' is used as meteorological driver. The source input is the official EMEP emission data. Monthly calculations are made having the last moment fields from the previous month as initial conditions for the next one. The boundary conditions are set to zero, so the influence of other European sources is not accounted for in this study. According to the EMEP methodology, multiple runs are made setting every time the sources of various countries to zero. The impact of every country in the pollution of all others is estimated.     

Concentrations of phthalate esters and identification of other additives in PVC children’s toys

This study was intended to provide data on the composition of soft PVC toys, addressing the widest practicable range of chemical additives and including non-phthalate additives. The study also included toys from as many countries as possible, since for many, no data were available. A total of 72 toys were purchased in 17 countries. The majority (64) were PVC or had PVC sections. In almost all the soft PVC toys analysed, phthalates comprised a sizeable proportion (most frequently 10–40%) of the total weight of the toy. The predominant phthalates detected were diisononyl phthalate (DINP) and di(2-ethylhexyl) phthalate (DEHP). Other phthalates identified in high concentrations in some toys include isomeric mixes of diisooctyl phthalate (DIOP) and diisodecyl phthalate (DIDP). The estrogenic chemical nonylphenol was isolated from 13 toys, while 2 toys were found to contain the fungicide Fungitrol 11 (Folpet). 78% of PVC toys contained one or more extractable organic compounds in addition to those reported above. Some of these data have been released previously by Greenpeace and made available on the internet.This report, however, which is intended for a technically expert audience, has been peer reviewed and contains further analytical data that have not been published before.     

Measurements of JNO3− in snow by nitrate-based actinometry

Chemical actinometry was used to measure nitrate photolysis rate coefficients, J_NO3⁻, on and in snowpack at Summit, Greenland. Sealed glass tubes containing nitrate and a hydroxyl radical trapping system were buried in snow and exposed for between 2 and 24 h. Average J_NO3⁻ values for 2-h midday exposures in early June on surface snow were 10–14×10⁻⁷ s⁻¹. Averages over 24 h were 3.5–4.5×10⁻⁷ s⁻¹. These values reflect the integrated photon flux and also any variation of the nitrate photolysis rate with temperature. Attenuation of J_NO3⁻ within the firn was 0.03–0.04 cm⁻¹ for 24-h exposures and 0.08 cm⁻¹ for a 2-h exposure. Different attenuation coefficients may relate to differential light penetration due to changes in sun angle over the course of 24 h.     

Snow-to-air exchanges of mercury in an Arctic seasonal snow pack in Ny-Ålesund,Svalbard

The study of mercury (Hg) cycle in Arctic regions is a major subject of concern due to the dramatic increases of Hg concentrations in ecosystem in the last few decades. The causes of such increases are still in debate, and an important way to improve our knowledge on the subject is to study the exchanges of Hg between atmosphere and snow during springtime. We organized an international study from 10 April to 10 May 2003 in Ny-Ålesund, Svalbard, in order to assess these fluxes through measurements and derived calculations.Snow-to-air emission fluxes of Hg were measured using the flux chamber technique between ∼0 and 50 ng m⁻² h⁻¹. A peak in Gaseous Elemental Mercury (GEM) emission flux from the snow to the atmosphere has been measured just few hours after an Atmospheric Mercury Depletion Event (AMDE) recorded on 22 April 2004. Surprisingly, this peak in GEM emitted after this AMDE did not correspond to any increase in Hg concentration in snow surface. A peak in GEM flux after an AMDE was observed only for this single event but not for the four other AMDEs recorded during this spring period.In the snow pack which is seasonal and about 40 cm depth above permafrost, Hg is involved in both production and incorporation processes. The incorporation was evaluated to ∼5–40 pg m² h. Outside of AMDE periods, Hg flux from the snow surface to the atmosphere was the consequence of GEM production in the air of snow and was about ∼15–50 ng m⁻² h⁻¹, with a contribution of deeper snow layers evaluated to ∼0.3–6.5 ng m⁻² h⁻¹. The major part of GEM production is then mainly a surface phenomenon. The internal production of GEM was largely increasing when snow temperatures were close to melting, indicating a chemical process occurring in the quasi-liquid layer at the surface of snow grains.     

Assessment of heavy metal concentrations in the food web of lake Beyşehir, Turkey

The accumulation of heavy metals (Cd, Pb, Hg and Cr) was measured by atomic absorption spectrophotometry in water, sediment, plankton and fish samples collected from Lake Bey?ehir, which is important bird nesting and visiting areas, and irrigation and drinking water sources. In Lake Bey?ehir, the accumulation orders of heavy metals were Cd>Pb>Cr>Hg in water, Pb>Cd>Cr>Hg in sediment, Pb>Cd>Cr>Hg in plankton, and Cd>Pb>Cr>Hg in the muscles and gills of chub, carp, tench, except for the muscle of pikeperch, in which it was Pb>Cd>Cr>Hg (P<0.05). In addition to this, accumulation orders of heavy metals in the food web was also found to be water>plankton>sediment>fish tissues, except for Cr. According to international criterias and Turkish regulations, heavy metal concentrations especially Cd and Pb in Lake Bey?ehir were markedly above the permissible levels for drinking water.     

Formation of strong airway irritants in a model mixture of (+)-α-pinene/ozone

The airway irritation of (+)-α-pinene, ozone, mixtures thereof, and formaldehyde was evaluated by a mouse bioassay, in which sensory irritation, bronchoconstriction, and pulmonary irritation were measured. The effects are distinguished by analysis of the respiratory parameters. Significant sensory irritation (assessed from reduction of mean respiratory rate) was observed by dynamic exposure of the mice, over a period of 30 min, to a ca. 22 s old reaction mixture of ozone and (+)-α-pinene from a Teflon flow tube. The starting concentrations were 6 ppm and 80 ppm, respectively, which were diluted and let into the exposure chamber. About 10% ozone remained unreacted (0.4 ppm), <0.2 ppm formaldehyde, <0.4 ppm pinonaldehyde, <2 ppm formic acid, and <1 ppm acetic acid were formed. These concentrations, as well as that of the unreacted (+)-α-pinene (51 ppm), were below established no effect levels. The mean reduction of the respiratory rate (30%) was significantly different (p≪0.001) from clean air, as well as from exposure of (+)-α-pinene, ozone, and formaldehyde themselves at the concentrations measured. Addition of the effects of the measured residual reactants and products cannot explain the observed sensory irritation effect. This suggests that one or more strong airway irritants have been formed. Therefore, oxidation reactions of common naturally occurring unsaturated compounds (e.g., terpenes) may be relevant for indoor air quality.     

Dating of marine sediments and time evolution of heavy metal concentrations in the Bay of Cádiz, Spain

In this paper the time evolution of heavy metal concentration of Pb, Zn, Cd and Hg, in the sediments of the Bay of Cádiz (southwest of Spain) is studied during the past century, as a result of the industrial influence in the zone. The study has been performed using sedimentary profiles that have been extracted from the seabed. The measurement of 210Pb and 137Cs radionuclides has provided the dating of the sediment layers, up to a depth corresponding to the age of 115 years. The relative sedimentation rates obtained are around 0.2 cm/year. The 137Cs activity profile reflects the concentration of this radionuclide in the atmosphere and into aquatic systems during the second half of the twentieth century. This profile has been used to ratify the results provided by the 210Pb dating method.     

Physicochemical characteristics of atmospheric aerosol during winter in the São Paulo Metropolitan area in Brazil

In order to characterize atmospheric aerosol in the São Paulo Metropolitan Area, aerosols were sampled during the winter months of August 1999 and August 2000. A micro-orifice uniform deposit impactor (MOUDI) was used. Samples were submitted to gravimetry, as well as to proton-induced X-ray emission (PIXE), carbon (black and organic) and ion-chromatography analysis. These analyses supplied information about mass concentrations and physicochemical properties of the particles. Due to the higher humidity, which can increase soluble particles diameters, and reduced atmospheric stagnation seen in 2000, average PM₁₀ concentrations were higher (105 μg m⁻³) in the winter of 1999 than in the winter of 2000 (60 μg m⁻³). The PIXE analysis revealed metals and metal compounds, soil-derived elements, Si-rich particles, sulfates, carbonates, chlorides and other anthropogenic air-borne particles, supposing molecules in their usual composition. Mass balance for PM_2.5 revealed significant participation of organic and black carbon, probably resulting from diesel burning by the heavy-duty fleet.     

Exploring the multifaceted role of TGF-β signaling in diabetic complications

Environmental Science and Pollution Research - Diabetes is one of the most comprehensive metabolic disorders and is spread across the globe. The data from IDF Diabetes Atlas and National Diabetes...     

FT-IR product study on the photo-oxidation of dimethyl sulphide in the presence of NOx—temperature dependence

The products of the OH radical-initiated oxidation of dimethyl sulphide (DMS) have been investigated as a function of temperature (284, 295, and 306 K) and different initial NO_x (NO+NO₂) concentrations: initial NO was varied between 434 and 2821 ppb and NO₂ between 135 and 739 ppb. The experiments were performed at 1000 mbar total pressure in synthetic air using the photolysis of H₂O₂ as the OH-radical source and FT-IR spectroscopy to monitor reactants and products. The major sulphur-containing products identified were SO₂, dimethyl sulphoxide (DMSO), dimethyl sulphone (DMSO₂), methane sulphonic acid (MSA), methane sulphonyl peroxynitrate (MSPN) and OCS. The variation of the product yields with temperature and NO_x concentration are consistent with the occurrence of both addition and abstraction channels in OH radical-initiated oxidation of DMS. Distinct trends in the yields of the various products have been observed as a function of temperature, initial NO_x conditions and also reaction time as NO is consumed in the system. Increasing the initial NO concentration was found to depress the DMSO, SO₂ and OCS formation yields and enhance those of DMSO₂, MSA and MSPN. The yield–time behaviour of DMSO₂ is supportive of a formation mechanism involving addition of O₂ to a (CH₃)₂SOH adduct, formed via the addition channel, followed by sequential reactions with NO and O₂. The mechanisms controlling the concentration–time profiles of the individual products under the present experimental conditions are discussed in detail and consideration is given to possible implications for the photo-oxidation of DMS under ambient conditions.     

Quantification of human adenovirus in irrigation water-soil-crop continuum: are consumers of wastewater-irrigated vegetables at risk?

Environmental Science and Pollution Research - Because of health concerns regarding the presence of enteric viruses in wastewater effluents, this study was designed to investigate the occurrence of...