活性污泥法处理高钙废水中污泥特性的变化

通过单级SBR法处理模拟高钙废水,研究了活性污泥法处理高钙废水的过程中钙离子对COD,MLVSS,MLSS,SVI,污泥增长速率,污泥形态结构及生物相的影响,揭示活性污泥法处理高钙废水的过程中污泥量巨大的原因。采用逐步增加钙离子浓度的方法,检测到在污泥培养期([Ca2+]=0 mg/L),COD去除率为98.1%,MLVSS和MLSS稳定在4 900~5 500mg/L,污泥增长速率为67 mg/(L·d),SVI为55~60 mL/g;在驯化处理期([Ca2+]=120~2 400 mg/L),COD去除率降至87.37%,MLVSS降至2 500 mg/L,MLSS增加至19 300 mg/L,污泥增长速率为212.31 mg/(L·d),SVI降至25 mL/g;在冲击期([Ca2+]=4 000 mg/L),COD去除率降至69.23%,MLVSS降至1 600 mg/L,MLSS迅速增加至24 200 mg/L,污泥增长速率为816.67 mg/(L·d),SVI降至14 mL/g。经显微镜观察发现,污泥絮体由松散变得密实,生物相由钟虫等指示性微生物变为不适应环境的胞囊结构。结果表明,随Ca2+浓度的增加,COD去除率下降,MLSS迅速增加,MLVSS和SVI急剧缩小,说明活性污泥中的活性微生物逐渐减少,而无机物组分逐渐增多;钙离子的加入促使系统碳酸平衡向右移动,使离子状态的钙大部分转化为难降解的碳酸盐,并附着于污泥絮体上,污泥绒粒被压缩,使污泥颗粒密实度及MLSS迅速增加,导致污泥排放量巨大。     

盐度对活性污泥驯化前后硝化特性的影响

通过批量试验系统研究了盐度对常规活性污泥硝化作用的影响以及污泥在含盐环境中经过驯化后其硝化功能的变化.试验结果表明,硝化菌比亚硝化菌对盐度更敏感,废水中含盐浓度为5 g/L时,对常规活性污泥中的亚硝化菌影响不大,硝化菌会受到一定程度的抑制;当含盐浓度超过10 g/L时,硝化菌和亚硝化菌均会受到严重抑制;含盐浓度大于30 g/L时,亚硝化菌和硝化菌已经完全受到抑制.在污泥驯化初期,耐盐硝化菌群数量较少,比硝化速率较低,硝化产物中亚硝态氮大量积累;随着驯化时间的延长,耐盐硝化菌群数量增加,比硝化速率增加,亚硝态氮累积量减少.污泥经过驯化后,硝化菌群可以逐渐适应高盐环境,在含盐浓度为30 g/L时硝化反应仍能进行.     

加压活性污泥法处理有机中间体废水的研究

对加压活性污泥法处理有机中间体废水进行了研究,主要考察了停留时间(HRT)、污泥浓度(MLSS)和反应压力等条件对COD去除率的影响.有机中间体废水经铁炭预处理后,COD从原来的8 000 mg/L降到5 000 mg/L左右,BOD5/COD由原来的0.20升高到0.40左右.当反应器内废水混合后COD 2 000 mg/L时,在反应压力0.10 MPa、污泥质量浓度3～5 g/L、停留时间8～10 h条件下,出水COD小于600 mg/L,COD去除率大于70%;出水经混凝沉淀处理后COD小于400 mg/L,可以达到<污水综合排放标准>(GB 8978-1996)三级标准.与常规的活性污泥处理方法相比,加压活性污泥法具有处理速度快、降解效率高和容积负荷大等优点.     

2株漂白废水高效降解菌的选育

用含氯漂白废水驯化城市污水处理厂的好氧污泥 ,从中分离出两株高效去除有机氯的菌 ,并对其适应条件进行了研究。结果表明 ,当pH为 7.0、废水浓度为 5 0 %、加入 0 .4g/L葡萄糖、2mL菌液时 ,处理效果较好 ,有机氯的去除率最高可达 74 .8%。     

SBR法处理保险粉废水

对SBR法处理保险粉废水的可行性进行了研究。结果表明,活性污泥经驯化后能较好地适应保险粉废水。该工艺在悬浮性固体(MLSS)含量为4 g/L,污泥负荷为0.23 kg COD/(kg污泥·d),水力停留时间(HRT)10 h,溶解氧(DO)2~4 mg/L以及实验温度25~35℃,周期为12 h的运行条件下,对COD的去除率为89.3%,完全达到该废水行业排放标准要求。其适宜的污泥龄为20 d,为中试和工艺设计应用提供了参考。     

高温厌氧膨胀颗粒污泥床反应器处理聚氯乙烯离心母液废水启动方法

采用高温厌氧膨胀颗粒污泥床(EGSB)反应器处理低浓度、难降解聚氯乙烯(PVC)离心母液废水,以天津市经济技术开发区污水处理厂序批式活性污泥法(SBR)工艺好氧污泥和生物接触氧化法处理PVC离心母液废水污泥的混合污泥为接种污泥,以葡萄糖模拟废水为基质,不断增加PVC离心母液废水所占比例的方法驯化厌氧微生物,实现了系统的成功启动。系统启动期间,进水有机负荷(以COD计)和水力停留时间分别保持在0.2 kg/(m3.d)和50 h左右,出水COD去除率和pH分别稳定在80%和8.0左右。结果表明,添加共代谢基质能利用基质间的协同作用缓解有毒物质对微生物的毒性作用,显著提高了废水的可生化性。通过采用改变水质、保持稳定负荷实现EGSB反应器处理PVC离心母液废水的成功启动证明,该启动方法具有良好的稳定性和可靠性。     

盐度对活性污泥硝化功能的影响

利用批量试验研究了盐度对常规活性污泥(非耐盐污泥)硝化功能的影响;通过逐步提高试验水的NaCl浓度驯化活性污泥,考察了驯化污泥的硝化功能;并进一步研究了适应于某NaCl浓度的耐盐硝化菌在受到盐度冲击时,其硝化功能的变化.结果表明,常规活性污泥中的硝化菌对盐度较敏感,当试验水中的NaCl质量浓度达到10.0 g/L时,污泥比硝化速率降低86%;通过逐步提高试验水的NaCl浓度对活性污泥进行长期驯化,可以驯化出耐盐硝化菌,耐盐污泥的比硝化速率接近于常规活性污泥的比硝化速率;适应于某NaCl浓度的耐盐硝化菌在受到盐度冲击时,NaCl浓度突然增加会对其产生更强的抑制作用.     

固定化活性污泥去除氨氮废水

采用PVA冷冻-解冻法固定传统活性污泥,用无机硝化菌培养基对其进行活性恢复和驯化培养.用该法制备的固定化活性污泥颗粒在三相流化床中处理氨氮废水,结果表明固定化活性污泥颗粒可处理低浓度氨氮废水,当氨氮浓度为60mg/L左右,固定化颗粒填充率9%,水力停留时间8 h,COD为400mg/L时,NH4+-N去除率达82.5%以上.实验还表明,该法制作的活性污泥颗粒寿命在3个月以上.     

ASBR中强化活性污泥与普通活性污泥降解啤酒废水的对照研究

在厌氧序批式反应器(ASBR)中采用优势菌群对活性污泥进行强化,驯化出强化活性污泥。与普通活性污泥处理啤酒废水对照显示,强化活性污泥较普通厌氧污泥驯化成熟时间短,处理效果更稳定、更有效,CODcr去除率最高达95％。培育出的强化活性污泥颗粒粒径为1．5～2．5cm,较普通活性污泥颗粒粒径更大,更均匀。     

低温降解苯胺高效菌群的筛选及特性研究

在低温下对吉林化工厂污水处理厂曝气池活性污泥、低温生活污水处理系统曝气池活性污泥、实验室菌种库保存的高效菌剂以及以上三者的混合样等4种样品进行了变温培养、驯化,筛选到一组低温降解苯胺高效菌群--吉化污泥.该菌群对苯胺初始浓度不高于800 mg/L驯化培养基中苯胺的降解率可以达到100%,当初始苯胺浓度升到1000 mg/L时,去除率也能保持在60%以上;菌胶团形成能力较强,菌胶团形成指数达到21.2%;并且在高岭土絮凝试验中表现出很强的生物絮凝能力.该菌群的生长温度范围为5-35℃,最适培养温度15℃,属于耐冷菌群.适合作为生物强化菌剂投加到低温苯胺类废水生物处理系统中,提高处理系统的净化能力.葡萄糖作为共代谢基质对低温苯胺生物降解有促进作用,而无机氮源作用不明显.     

污泥减量过程中臭氧氧化对硝化和反硝化影响的试验研究

采用AO工艺,考察了在污泥减量过程中臭氧(O3)氧化对生物系统硝化和反硝化能力的影响.结果表明,在每克SS中O3投量为0.05 g时,氧化后污泥中的CODcr由37.5 mg/L增至700mg/L,TN由4.86 mg/L增至36.6 mg/L,NH4 -N由0.353mg/L增至7.49 mg/L,NO3--N由2.19 mg/L增至5.15 mg/L.虽然氧化系统出水NH4 -N浓度略高于对照系统,但氧化系统NH4 -N的去除率大于98%,硝化能力基本没有受到O3氧化的影响.O3氧化污泥后增加的有机物作为附加的碳源循环至缺氧段,提高了反硝化的效果,当污泥氧化比例分别为10%、20%、30%时,进入缺氧段的CODCr/TN分别平均增至11.21、11.56、11.88,氧化系统的反硝化效果也随之分别提高5%、25%、37%.     

Petroleum refinery stripped sour water treatment using the activated sludge process

A pilot study was performed over 91 days to determine if the activated sludge process could treat a segregated stripped sour water (SSW) stream from a petroleum refinery. The study was performed in two periods. The first period was terminated after 19 days, as a result of excessive sludge bulking. The elimination of sludge bulking during the 70-day second period is attributed to operational changes, which included aerating the influent to oxidize reduced sulfur, adjusting the influent pH, and adding micronutrients to satisfy biological requirements. The pilot plant provided a chemical oxygen demand (COD) removal of up to 93%. Nitrification was achieved, with effluent ammonia values < 1 mg-N/L. These results indicate that direct treatment of SSW with the activated sludge process is possible and has direct application to full-scale petroleum refinery wastewater plant upgrades.     

污泥活性炭强化SBR法处理垃圾渗滤液的实验研究

为了进一步处理垃圾渗滤液，试验采用污泥活性炭强化序批式间歇反应器（SBR）法进行处理，通过对比普通SBR法试验，得出投加污泥活性炭强化SBR法处理垃圾渗滤液的效果要远远高于普通SBR法。当污泥活性炭的投加量为1.2 g/L，容积负荷为0.5～1.5 kg BOD₅/(m³·d)时，进水1 h，曝气10 h，沉淀1.5 h，闲置1.5 h，处理效果最好，COD的去除率达到了85%，NH³-N的去除率达到了90%。     

Hybrid process for heavy metal removal from wastewater sludge.

Bioleaching processes have been demonstrated to be effective technologies in removing heavy metals from wastewater sludge, but long hydraulic retention times are typically required to operate these bioprocesses. A hybrid process (coupling biological and chemical processes) has been explored in laboratory pilot-scale experiments for heavy metals (cadmium [Cd], copper [Cu], chromium [Cr], and zinc [Zn]) removal from three types of sludge (primary sludge, secondary activated sludge, and a mixture of primary and secondary sludge). The hybrid process consisted of producing a concentrate ferric ion solution followed by chemical treatment of sludges. Ferric iron solution was produced biologically via oxidation of ferrous iron by A. ferrooxidans in a continuous-flow stirred tank (5.2 L) reactor (CSTR). Wastewater sludge filtrate (WSF) containing nutrients (phosphorus and nitrogen) has been used as culture media to support the growth and activity of indigenous iron-oxidizing bacteria. Results showed that total organic carbon (TOC) concentrations of the culture media in excess of 235 mg/L were found to be inhibitory to bacterial growth. The oxidation rate increased as ferrous iron concentrations ranged from 10 to 40 g Fe2+/L. The percentage of ferrous iron (Fe2+) oxidized to ferric iron (Fe3+) increased as the hydraulic retention time (HRT) increased from 12 to 48 h. Successful and complete Fe2+ oxidation was recorded at a HRT of 48 h using 10 g Fe2+/L. Subsequently, ferric ion solution produced by A. ferrooxidans in sludge filtrate was used to solubilize heavy metals contained in wastewater sludge. The best solubilization was obtained with a mixture of primary and secondary sludge, demonstrating a removal efficiency of 63, 71, 49, and 80% for Cd, Cu, Cr, and Zn, respectively.     

城市污水生化处理水UV/O3法深度处理效果及影响因素研究

研究城市污水生化处理水的深度处理技术及其影响因素,对于减轻环境污染和实现废水回用具有重要理论意义和实用价值。考察了UV／O3法对城市污水生化处理水深度处理的效果及其影响因素。结果表明,由于UV／O3过程具有氧化能力强,反应无选择性等优点,使其在城市污水生化处理水深度处理方面较普通O3氧化更具有优势,50min时CODCr去除率达到90％以上,达到了深度处理的目的。对于难氧化有机物,UV／O3法处理时几乎大部分都被氧化分解残留量很少,而O3法处理时仍有较多难氧化有机物残留。UV／O3法处理城市污水生化处理水时,在pH=6～9时,CODCr去除率随pH的升高而降低,表明较低pH（pH=5）有利CODCr的去除。有机污泥对CODCr去除率基本没有影响。但无机悬浮物SiO2对CODCr去除率影响较大,投加70mg／L的SiO2后CODCr氧化速率和去除率有较明显下降。随溶液碱度的增加,CODCr的去除率下降,碱度越高对CODCr去除的影响也越明显。     

复合生物反应器工艺对化纤废水的处理研究

在普通活性污泥系统的曝气池中投加一定量的填料构成复合生物反应器 ,可以增加曝气池中的生物体量至 6g/L左右 ,在HRT为 8h ,泥龄为 5d时 ,CODCr、氨氮的去除率分别提高了 2 0 %和9.6% ,容积负荷对复合生物反应器的脱氮能力影响较小。该工艺对污泥膨胀有较好的控制     

利福平废水的絮凝和生化处理研究

利福平生产的废水COD高达6万,用PFS、C-PAM脱稳,密集网捕式絮凝处理后,COD去除率达27%,BOD5/CODCr从0.19上升到0.32.絮凝前后水质和色谱分析表明,絮凝后5种有机物去除效率均在22%以上,使生化处理成为可能,进生化池废水经稀释后,用活性污泥法处理9天后,COD从1.5万降至COD＜300mg/L,达到治理要求.     

低温条件下硝化污泥的驯化

为了在低温13～14％下取得较好的硝化效果，分3个温度阶段25℃，16～17℃，13—14℃对活性污泥进行了驯化培养，研究了进水氨氮浓度和混合液COD对硝化污泥的影响。实验结果表明，硝化污泥经过驯化培养后，氨氮去除率可达80％以上，且在DO浓度为2ing／L，pH为6．7～7．5，进水氨氮为300mg／L，混合液COD为80mg／L条件下，硝化污泥能取得较快的增长，氨氮平均去除率可达89％。     

Competition between polyphosphate- and glycogen-accumulating organisms in enhanced-biological-phosphorus-removal systems: effect of temperature and sludge age.

Temperature and sludge age were found to be important factors in determining the outcome of competition between polyphosphate-accumulating organisms (PAOs) and glycogen-accumulating non-polyphosphate organisms (GAOs) and the resultant stability of enhanced-biological-phosphorus removal (EBPR). At 20 degrees C and a 10-day sludge age, PAOs were dominant in an anaerobic/aerobic (A/O) sequencing-batch reactor (SBR), as a result of their higher anaerobic-acetate-uptake rate and aerobic-biomass yield than GAOs. However, at 30 degrees C and a 10-day sludge age, GAOs were able to outcompete PAOs in the A/O SBR because of their higher anaerobic-acetate-uptake rate than PAOs. At 30 degrees C and a 5-day sludge age, GAOs coexisted with PAOs in the A/O SBR, resulting in unstable EBPR performance. At 30 degrees C, reducing the sludge age from 5 to 3 days improved the EBPR efficiency drastically, and the EBPR performance was stable. The maximum specific-anaerobic-acetate-uptake rates of GAO-enriched sludge were affected by temperature with the Arrhenius temperature coefficient theta of 0.042 (degrees C(-1) between 10 and 30 degrees C. The effect of sludge age (5 and 10 days) on the maximum specific-anaerobic-acetate-uptake rates of GAO-enriched activated sludge, however, was not significant. For the PAO-enriched activated sludge, the maximum specific-anaerobic-acetate-uptake rate did not change significantly between 20 and 30 degrees C, but significantly increased from 0.38 to 0.52 mmol-C/ mmol-C/h as the sludge age decreased from 10 to 3 days at 30 degrees C.