用于生物接触氧化工艺的填料特性比较研究

填料材质、结构等影响到生物膜的性状和水力学特性，是决定生物接触氧化工艺处理效果的关键因素。本文分别选取了悬挂式填料和悬浮式填料各2种填料，分别从COD与NH2-N的去除、充氧效率和出水浊度等方面对各种填料处理城市污水进行了比较研究。实验结果表明，悬挂式填料具有挂膜快、处理效果稳定，受环境变化影响较小；悬浮式填料受气水作用能够悬浮转动而具有较强的布水、布气功能；生物量的差异导致悬浮式填料和悬挂式填料处理效果和充氧效率不同，悬浮式填料生物膜容易脱落导致系统受负荷冲击时生物量流失而处理效果变差；软性填料生物膜容易板结成球，容易导致其处理效果降低。     

不同填料对反应器充氧能力影响的比较研究

填料是生物接触氧化工和进气量的情况下DO的变化,分析填料对曝气池DO的转移速率有无影响.实验结果表明:对悬浮式填料而言,选择合适的曝气量,投加率在一定的范围内时,随着投加率的增加,曝气池充氧能力增强;对悬挂式填料而言,弹性立体填料的放射状细条结构对气泡起到较强的切割作用,提高了充氧效率.曝气池充氧能力受填料投加率的影响程度顺序为:弹性立体填料＞立体块式悬浮填料＞内置悬浮球形填料＞盾式填料.     

SBBR工艺处理生活污水探讨

序批式生物膜法(SBBR)是将生物膜与序批式活性污泥法(SBR)相结合而开发出的污水处理复合新工艺,既保留了SBR的优点又具有生物膜法的特点。其运行方式可根据实际需要灵活操作,同时高效地脱氮、除磷和去除有机物。试验采用SBBR处理生活污水,选用特有的壁挂式软性填料。结果表明,所形成的微生物系统稳定,生物种群多样化,生物量丰富,对城市生活污水具有较好的处理效果。     

序批式生物膜反应器处理农村生活污水的填料对比研究

选用4种填料进行序批式生物膜反应器(SBBR)处理农村生活污水的研究,通过出水COD、NH4+-N等指标的测定以及生物膜的扫描电镜观察,考察了运用不同填料时SBBR的污染物去除情况和生物膜的长势,以期筛选出适用于农村生活污水处理的填料。结果表明,3#、4#SBBR(分别选用组合填料和碳素纤维填料)的DO、pH波动幅度均相对较小,比1#、2#SBBR(分别选用立体网状填料及海绵填料)更加稳定;4#SBBR的COD去除效果最好,水力停留时间仅需5h,3#SBBR的COD去除效果其次,所需水力停留时间为6h,而1#、2#SBBR在运行8h时也无法将COD完全消化;3#、4#SBBR出水的NH4+-N、TN去除效果均高于1#、2#SBBR;采用4种填料的SBBR的生物膜长势优劣情况为碳素纤维填料>组合填料>海绵填料>立体网状填料;碳素纤维填料及组合填料在受到进水负荷冲击后,能相对较快适应环境,且填料上的微生物活性较高,较适合运用于中国农村生活污水的处理。     

2种填料作为生物膜载体修复微污染河水的比较

采用序批式生物反应器(SBBR),在水温为(19.0±1.5)℃,DO≥4.5 mg/L条件下,比较基于2种生物膜填料(竹丝和空心塑料球)上的微生物对微污染河水中高锰酸钾指数(COD Mn)、总氮(TN)和总磷(TP)等的去除效果。结果表明,经过4 h的运行,竹丝作为生物膜载体时,COD Mn、TN的去除分别为17.5%~48.8%和49.38%~70.93%,但TP的去除效果不明显;而基于空心塑料球的生物膜对COD Mn的去除率仅为2.4%~42%,对TN和TP去除效果均不明显。通过显微分析发现,基于竹丝填料生物载体上微生物种类、数量明显多于空心塑料球。     

生物流化床中生物膜特性与反应器效率的关系

综述了生物流化床处理有机废水时生物膜的特性及其对反应器效率的影响。包括反应器中生物膜的形成及影响生物膜形成的因素;生物膜的活性及膜厚、基质浓度和不同种群微生物在生物膜中的分布对其活性的影响;生物膜的传质特性;生物膜厚度与反应器效率的关系;生物膜的脱膜及其数学模型;提出了生物流化床今后的研究重点     

曝气生物滤池深度处理混合印染废水

采用曝气生物滤池(BAF)反应器作为混合印染废水的深度处理工艺,对BAF的启动情况和不同气水比条件下BAF的深度处理效能进行探讨。结果表明,采用同步连续法可实现BAF在15 d内快速启动;当气水比为3∶1时,二级处理出水的处理效果最好,氨氮、COD和色度去除率分别达到77.8%、61.5%和90%。比较BAF中生物膜和活性污泥对二级处理出水的深度处理效能性能时发现,在相同生物量和环境条件下生物膜表现了出更强深度处理能力。     

悬浮填料生物膜反应器处理黑水的启动挂膜

采用自然挂膜法在低碳氮比的黑水中启动悬浮填料生物膜反应器,探讨了进水有机物和氨氮负荷率对挂膜启动的影响,分析了挂膜过程中溶解性化学需氧量(SCOD)、氨氮(NH+4-N)和总氮(TN)的去除转化规律及填料上附着生物量和填料生物相的变化规律。研究结果表明,在DO为1.5~2.5 mg/L、温度为(21±2)℃等条件下可快速(43 d)启动生物硝化挂膜,SCOD、NH+4-N和TN去除率分别可达到84%、62%和46%,单个填料上的生物膜量达到0.49 g/个。进水SCOD、NH+4-N负荷率明显影响硝化细菌在填料上的成膜和生物硝化效率。研究认为,进水SCOD、NH+4-N负荷率分别保持5.34g/(m2·d)、1.44 g/(m2·d)左右,能够促快速挂膜并获得良好的短程硝化和同步硝化反硝化效果。     

新型立体浮床处理河道微污染源水的挂膜特性

立体浮床是一种新型的生物预处理方法。采用了"曝气充氧+新型立体浮床"强化处理方法治理微污染河水,对立体浮床挂膜期间底部填料上的生物膜特性及微污染河水处理效果进行了实验研究。结果表明,在河道水温为15.2～23.6℃,pH在7.0～7.8,溶解氧浓度为4.0～5.9 mg/L时,经40 d左右时填料挂膜成熟。通过对水质和微生物指标分析,填料挂膜分为4阶段:物理吸附阶段—物理吸附-生物繁殖阶段—生物强化吸附降解阶段—挂膜成熟阶段。填料挂膜成熟后,污染物去除效果良好,浊度、COD和NH3-N的去除率分别达到了20.1%、17.5%和18.3%。     

气液相组合生物法净化低浓度甲醛废气研究

对生物膜填料塔 液相生物处理的组合系统净化低浓度甲醛废气进行实验研究,结果表明,组合系统对甲醛废气的净化效果明显优于单独生物膜填料塔净化系统,甲醛净化效率提高35%以上,甲醛生化去除量增大50%以上.动力学研究结果表明,甲醛在生物膜上的生化降解反应为慢速生化反应,需要采取强化甲醛液相生化降解反应、提高反应速率的措施,来提高废气中甲醛的生物净化效果.     

Aerobic Treatment of a Nitrogen-Limited Chemical Process Waste water

Abstract

Nitrogen transformations and their effect on aerobic suspended growth treatment of an industrial wastewater were studied in three parallel bench-scale reactors operated at 5 "C at mean cell residence times (MCRT) of 15, 30, and 60 days. In normal process wastewater, the bulk of influent nitrogen was in organic form, and the fraction transformed was almost totally incorporated into synthesized biomass. Assimilative control by heterotrophs maintained ammonianitrogen levels below permitted effluent levels, and nitrification was not significant. Although volatile suspended solids had a nitrogen content of only 5% to 8%, effective organics removal was maintained, and total organic carbon and filtered daily average five-day biochemical oxygen demand (BODS) were below permitted effluent levels. A marked improvement in settleability and lower effluent total suspended solids was achieved by adding ammonia-nitrogen to the wastewater in excess of stoichiometric growth requirements.

During a batch production cycle of a cationic chemical, the ratio of nitrogen to chemical oxygen demand and the fraction of the total influent nitrogen in soluble form increased in the wastewater. Reactor effluent ammonia levels increased to above permit levels at all three MCRTs during treatment of wastewater containing cationic production effluents. The magnitude of ammonia increase was greater for longer MCRTs, suggesting that synthesis of cell mass was not capable of assimilating the increased ammonia supply under these non-steady conditions. The experimental results suggest several potential strategies for operating the aerobic process at the treatment facility, including adding nitrogen to improve settleability and discontinuing these additions when wastewater contains a high ratio of nitrogen to chemical oxygen demand and an elevated soluble nitrogen fraction     

Treatability studies on wastewater from textile dyeing factories in Bursa, Turkey

The textile industry is one of the most rapidly developing industries in Turkey. It generates a large amount of wastewater, with corresponding concerns about pollution. The main sources of pollution in wastewater are the dyeing and finishing processes. The dyestuffs and polyvinyl alcohol (PVA) are the main refractory organics of concern in terms of meeting more stringent effluent standards of chemical oxygen demand (COD) and colour. In this study, wastewaters from textile dyeing factories in Bursa were characterised, and physical, chemical and biological treatability studies were carried out. In the physical and chemical studies, 60.80% COD, 80% suspended solids (SS) and 10.92% turbidity removal efficiencies were obtained. In the biological studies, 90% COD and 40% SS removal were obtained. The initial soluble inert COD of wastewater was determined by using comparison methods. The initial inert COD of wastewater and the microbial product concentration were determined as 37 mg/l and 13 mg/l, respectively.     

Adverse effects of erythromycin on the structure and chemistry of activated sludge

This study examines the effects of erythromycin on activated sludge from two French urban wastewater treatment plants (WWTPs). Wastewater spiked with 10 mg/L erythromycin inhibited the specific evolution rate of chemical oxygen demand (COD) by 79% (standard deviation 34%) and the specific N-NH₄⁺ evolution rate by 41% (standard deviation 25%). A temporary increase in COD and tryptophan-like fluorescence, as well as a decrease in suspended solids, were observed in reactors with wastewater containing erythromycin. The destruction of activated sludge flocs was monitored by automated image analysis. The effect of erythromycin on nitrification was variable depending on the sludge origin. Erythromycin inhibited the specific nitrification rate in sludge from one WWTP, but increased the nitrification rate at the other facility.     

陶瓷印花废水处理的混凝剂及工艺条件

采用混凝剂聚合氯化铝（PAC）、聚丙烯酰胺（PAM）、聚合硫酸铁（PFS）对陶瓷印花废水进行混凝沉降处理，监测水样的吸光度、浊度、悬浮物，以脱色率、浊度去除率、悬浮物去除率评价混凝处理的效果。结果表明：PAC是陶瓷印花废水沉降处理的理想混凝剂；水样的吸光度、浊度、悬浮物随混凝剂用量增大和沉降时间延长而呈降低趋势，而脱色率、浊度去除率、悬浮物去除率随混凝剂和沉降时间的增大呈增大的趋势；PAC投加量为20mg／L，沉降时间约为24h，水样脱色率达到90．0％，而当PAC投加量达到100mg／L，沉降时间约为4h，陶瓷印花水的脱色率可达到96．0％。证明了药剂用量的增加与沉降时间的延长对混凝过程具有增效作用。     

The efficiency of electrocoagulation in treating wastewater from a dairy industry, part I: iron electrodes

Iron electrodes were used for electrocoagulation (EC) treatment of wastewater from a dairy plant. Electrolysis time, pH, current density and distance between electrodes were considered to assess the removal efficiency of chemical oxygen demand (COD), total solids (TS) and their fractions and turbidity. Samples were collected from the effluent of a dairy plant using a sampling methodology proportional to the flow. The treatments were applied according to design factorial of half fraction with two levels of treatments and three repetitions at the central point. The optimization of parameters for treating dairy industry effluent by electrocoagulation using iron electrodes showed that electric current application for 15 minutes, an initial sample pH close to neutral (pH 7.0) and a current density of 50 A (.)(m-2) resulted in a significant reduction in COD by 58 %; removal of turbidity, suspended solids and volatile suspended solids by 95 %; and a final treated effluent pH of approximately 9.5. Negative consequences of the type of electrode used were the emergence of an undesirable color and an increase in the proportion of dissolved solids in the treated effluent.     

皮革废水混凝处理实验研究

采用混凝剂对皮革废水进行混凝处理。对3种无机混凝剂和一种有机混凝剂进行了筛选,研究了pH值和投药量对废水中SS、COD、铬和色度等污染物去除效果的影响。结果表明,当pH值在酸性和中性时,效果不明显;当pH值为碱性时,效果显著。硫酸亚铁、硫酸亚铁+PAM和聚合氯化铝(PAC)+PAM 3种混凝剂组合具有良好的混凝效果,在合适的pH值和投药量下,SS和COD的去除率分别达到80%和30%以上,铬和色度的去除率分别达到95%和50%以上。且硫酸亚铁混凝效果好,成本低,适合小型皮革企业需求。     

Treatment of domestic wastewater by an hydroponic NFT system

The objectives in this work were to investigate a conceptual layout for an inexpensive and simple system that would treat primary municipal wastewater to discharge standards. A commercial hydroponic system was adapted for this study and the wastewater was used to irrigate Datura innoxia plants. Influent and effluent samples were collected once a month for six months and analysed to determine the various parameters relating to the water quality. The legal discharge levels for total suspended, biochemical oxygen demand and chemical oxygen demand were reached with the plant system after 24 h of wastewater treatment. Total nitrogen and total phosphorus reduction were also obtained. NH4(+)-N was reduced by 93% with nitrification proving to be the predominant removal process. Significant nitrification occurred when the BOD5 level dropped 45 mg/l. Similar results were obtained for six months although the sewage composition varied widely. D. innoxia develops and uses the wastewater as the unique nutritive source.     

Advanced oxidation treatment of physico-chemically pre-treated olive mill industry effluent

In this study, the applicability of physico-chemical methods was investigated for the pre-treatment of the olive mill effluents prior to the discharge into the common sewerage ending with a municipal wastewater treatment plant. The samples were taken from an olive oil industry operated as three-phase process located in Turkey. Various pre-treatment methods including acid craking, polyelectrolyte and lime additions were applied. Advanced oxidation study using Fenton's process was also investigated following pre-treatment by acid cracking and cationic polyelectrolyte. Acid cracking alone gave satisfactory treatment efficiencies and polyelectrolite additions to the acid-cracked samples enhanced treatment efficiency. Since a complete treatment plant is available at the end of the sewer system, results indicated that the effluents of the investigated industry could be discharged into the municipal sewerage in the case of total chemical oxygen demand (COD(tot)), suspended solid (SS) and volatile suspended solid (VSS) concentrations according to the Turkish Water Pollution Control Regulation after pre-treatment with 5 ppm anionic polyelectrolyte following acid cracking. The minimum COD(tot), SS and VSS removals were observed when raw wastewater was pre-treated with lime and the discharge standards to the municipal sewer system could not be met. Advanced oxidation with Fenton's process was applied after acid cracking and cationic polyelectrolyte treatment in order to investigate further reduction in chemical oxygen demand (COD) concentration for minimizing the influence of this industrial discharge on the existing municipal wastewater treatment plant. Results indicated that COD(tot) removal increased up to 89% from 74% after Fenton's oxidation for the acid cracked samples in which cationic polyelectrolite (10 ppm) was added.     

微波辅助工艺处理天然气净化废水的应用研究

进行了微波辅助工艺处理天然气净化废水的应用研究,考察了废水色度、COD、SS、含油量和细菌的去除效果以及对废水腐蚀率的降低作用,并进行了同等条件下的常温对照实验。研究结果表明:微波絮凝工艺中絮凝剂PAC和PAM的用量较常温下减少了100 mg/L和5 mg/L,絮凝沉降时间仅为常温絮凝的1/4,最佳微波辐照时间下废水的COD去除率比常温条件下提高4.6%。微波工艺处理后,难降解天然气净化废水的含油量去除率达到了94%、废水中硫酸盐还原菌死亡率达97%以上,废水腐蚀率降为原来的1/7,废水可生化性得到了很大提高,可直接进行好氧生化处理。实验表明,微波辅助工艺对难降解天然气净化废水具有很好的处理应用效果。