Sorption of the fumigant 1,3-dichloropropene on soil

The fumigant 1,3-dichloropropene (1,3-D) is considered a major replacement to methyl bromide, which is to be phased out of use in the United States by 2005. The main purpose of this study was to evaluate soil-water partitioning of 1,3-D in two California agricultural soils (Salinas clay loam and Arlington sandy loam). The partition coefficients (Kd and Kf) were determined by directly measuring the concentration of 1,3-D in the solid phase (Cs) and aqueous phase (Cw) after batch equilibration. In the Salinas clay loam, the Kf of cis-1,3-D in adsorption and desorption isotherms was 0.47 and 0.54, respectively, with respective values of 0.39 and 0.49 for trans-1,3-D. This slight hysteric effect suggests that a different range of forces are involved in the adsorption and desorption process. Since n was near unity in the Freundlich equation, the Freundlich isotherms can also be approximated using the liner isotherm. At 25 degrees C, the Kd of the 1,3-D isomers in both soils ranged from 0.46 to 0.56, and the Koc (organic matter partition coefficient) ranged from 58 to 70. The relatively low Kd values and a Koc that falls within the range of 50-150, suggests that 1,3-D is weakly sorbed and highly mobile in these soils. Understanding the sorption behavior of 1,3-D in soil is important when developing fumigation practices to reduce the movement of 1,3-D to the air and groundwater.     

Distribution of polycyclic aromatic hydrocarbons in soil-water system containing a nonionic surfactant

The effect of a nonionic surfactant, Triton X-100 (TX100), on the distribution of four representative polycyclic aromatic hydrocarbons (PAHs), phenanthrene, fluorene, acenaphthene and naphthalene, in soil-water system was studied on a natural soil. The apparent soil-water distribution coefficient with surfactant (Kd*) for these compounds increased when TX100 equilibrium concentration from zero to around the critical micelle concentration (CMC), followed by a decrease in Kd* at TX100 equilibrium concentration greater than CMC. This is a direct result of surfactant sorption onto soil followed by PAHs partitioning to the sorbed surfactant. The values of carbon-normalized solute distribution coefficient (Kss) with the sorbed TX100 are greater than the corresponding partition coefficients with soil organic matter (Koc), which indicates the soil-sorbed nonionic surfactant is more effective per unit mass as a partitioning medium than the native soil organic matter for PAHs. When Kd* = Kd the corresponding initial concentration of surfactant was defined as critical washing concentration (CWC). Depending on the surfactant initial concentration below or above the CWC, the addition of nonionic surfactant can enhance the retardation of soil for PAHs or promote the removal of PAHs from soil, respectively. The values of Kd* and CWC can be predicted by a model, which correlates them with the compounds' octanol-water partition coefficients (Kow), soil property and the amount of soil-sorbed surfactant.     

Thermodynamics of interaction of lindane on silty loam and silty clay loam Indian soils

Abstract

Interaction of lindane with silty loam and silty clay loam soils was studied in batch tests at 23, 30 and 37° C. Sorption experiments were carried out at four concentrations and for varying time of contact upto 72 hours. This was followed by desorption studies. No desorption was observed. The sorption data was analysed using sorption equations and evaluating the thermodynamic parameters. The sorption was found to be predominantly entropic in nature and a combined effect of adsorption and chemisorption. The effect of organic matter and other chemical and mineralogical constituents of soils has also been discussed. The sorption with single application of lindane with the two soil types indicates that the insecticide is less likely to reach groundwater.     

Effect of organic fertilizers derived dissolved organic matter on pesticide sorption and leaching

Incorporation of organic fertilizers/amendments has been, and continues to be, a popular strategy for golf course turfgrass management. Dissolved organic matter (DOM) derived from these organic materials may, however, facilitate organic chemical movement through soils. A batch equilibrium technique was used to evaluate the effects of organic fertilizer-derived DOM on sorption of three organic chemicals (2,4-D, naphthalene and chlorpyrifos) in USGA (United States Golf Association) sand, a mixed soil (70% USGA sand and 30% native soil) and a silt loam soil (Typic Fragiochrept). DOM was extracted from two commercial organic fertilizers. Column leaching experiments were also performed using USGA sand. Sorption experiments showed that sorption capacity was significantly reduced with increasing DOM concentration in solution for all three chemicals. Column experimental results were consistent with batch equilibrium data. These results suggest that organic fertilizer-derived DOM might lead to enhanced transport of applied chemicals in turf soils.     

Sorption of 3,4-dichloroaniline on four contrasting Greek agricultural soils and the effect of liming

Sorption of 3,4-dichloroaniline (3,4-DCA) on four typical Greek agricultural soils, with distinct texture, organic matter content and cation exchange capacities, was compared by using sorption isotherms and the parameters calculated from the fitted Freundlich equations. The sorption process of 3,4-DCA to the soil was completed within 48–72 h. The 3,4-DCA sorption on all soils was well described by the Freundlich equation and all sorption isotherms were of the L-type. The sandy clay loam soil with the highest organic matter content and a slightly acidic pH was the most sorptive, whereas the two other soil types, a high organic matter and neutral pH clay and a low organic matter and acidic loam, had an intermediate sorption capacity. A typical calcareous soil with low organic matter had the lowest sorption capacity which was only slightly higher than that of river sand. The 3,4-DCA sorption correlated best to soil organic matter content and not to clay content or cation exchange capacity, indicating the primary role of organic matter. The distribution coefficient (K _d) decreased with increasing initial 3,4-DCA concentration and the reduction was most pronounced with the highly sorptive sandy clay loam soil, suggesting that the available sorption sites of the soils are not unlimited. Liming of the two acidic soils (the sandy clay loam and the loam) raised their pH (from 6.2 and 5.3, respectively) to 7.8 and reduced their sorption capacity by about 50 %, indicating that soil pH may be the second in importance factor (after organic matter) determining 3,4-DCA sorption.     

Sorption of 3,4-dichloroaniline on four contrasting Greek agricultural soils and the effect of liming

Sorption of 3,4-dichloroaniline (3,4-DCA) on four typical Greek agricultural soils, with distinct texture, organic matter content and cation exchange capacities, was compared by using sorption isotherms and the parameters calculated from the fitted Freundlich equations. The sorption process of 3,4-DCA to the soil was completed within 48-72 h. The 3,4-DCA sorption on all soils was well described by the Freundlich equation and all sorption isotherms were of the L-type. The sandy clay loam soil with the highest organic matter content and a slightly acidic pH was the most sorptive, whereas the two other soil types, a high organic matter and neutral pH clay and a low organic matter and acidic loam, had an intermediate sorption capacity. A typical calcareous soil with low organic matter had the lowest sorption capacity which was only slightly higher than that of river sand. The 3,4-DCA sorption correlated best to soil organic matter content and not to clay content or cation exchange capacity, indicating the primary role of organic matter. The distribution coefficient (K(d)) decreased with increasing initial 3,4-DCA concentration and the reduction was most pronounced with the highly sorptive sandy clay loam soil, suggesting that the available sorption sites of the soils are not unlimited. Liming of the two acidic soils (the sandy clay loam and the loam) raised their pH (from 6.2 and 5.3, respectively) to 7.8 and reduced their sorption capacity by about 50 %, indicating that soil pH may be the second in importance factor (after organic matter) determining 3,4-DCA sorption.     

Adsorption,desorption, and mobility of two insecticides in Malaysian agricultural soil

Laboratory studies utilizing radioisotopic techniques were conducted to determine the adsorption, desorption, and mobility of endosulfan (6,7,8,9,10,10-hexachloro-1,5,5a,6,9,9a-hexahydro-6,9-methano-2,4,3-benzodioxanthiepin3-oxide) and methamidophos (O,S-dimethyl phosphorothioate) in sandy loam and clay soils of the Cameron Highlands and the Muda rice-growing area, respectively. High Freundlich adsorption distribution coefficients [Kads(f)] for endosulfan (6.74 and 18.75) and low values for methamidophos (0.40 and 0.98) were obtained in the sandy loam and clay soils, respectively. The observed Koc values for endosulfan were 350.85 (sandy loam) and 1143.19 (clay) while Koc values of 20.92 (sandy loam) and 59.63 (clay) were obtained for methamidophos. Log Kow of 0.40 and 1.25 were calculated for endosulfan as well as -1.96 and -1.21 for methamidophos in the sandy loam and clay soils, respectively. Desorption was common to both pesticides but the desorption capacity of methamidophos from each soil type far exceeded that of endosulfan. Soil thin layer chromatography (TLC) and column studies showed that while methamidophos was very mobile in both soils, endosulfan displayed zero mobility in clay soil.     

Sorption behaviour of acetochlor,atrazine, carbendazim,diazinon, imidacloprid and isoproturon on Hungarian agricultural soil

Laboratory studies were conducted to determine the sorption behaviour of six commonly used pesticides (acetochlor, atrazine, carbendazim, diazinon, imidacloprid and isoproturon) on Hungarian brown forest soil with clay alluviation (Luvisol) using the batch equilibrium technique. The sorption isotherms could be described by the Freundlich equation in non-linear form (n < 1) for all compounds, however in case of diazinon using the extended Freundlich equation proved to be a better approach. The adsorption constant related soil organic carbon content (Koc) calculated from Freundlich equation were 314 for acetochlor, 133 for atrazine, 2805 for carbendazim, 1589 for diazinon, 210 for imidacloprid and 174 for isoproturon. The octanol-water partition coefficients (Pow), which can be a useful parameter to predict of adsorption behaviour of a chemical on soil, and dissociation coefficients of these pesticides were calculated based on the chemical structure of them using a computerized expert system. The octanol-water partition coefficients were determined experimentally from high performance liquid chromatographic parameters as well. Good agreement was observed between experimental and the computer expert system estimated data. Computer estimated log Pow values ranged 0.5 and 3.86 for the examined pesticides, with imidacloprid and diazinon being the least and most hydrophobic respectively. Experimentally determined logPow ranged between 0.92 and 3.81 with the same tendency. It can be concluded that the Freundlich adsorption constants (Kf) are slightly related to the octanol-water partition coefficients of investigated chemicals, nevertheless no close correlation could be established because of the influence of further characteristics of solutes and soil.     

Sorption and desorption kinetics of diuron, fluometuron, prometryn and pyrithiobac sodium in soils

The sorption and desorption characteristics of four herbicides (diuron, fluometuron, prometryn and pyrithiobac-sodium) in three different cotton growing soils of Australia was investigated. Kinetics and equilibrium sorption and desorption isotherms were determined using the batch equilibrium technique. Sorption was rapid (> 80% in 2 h) and sorption equilibrium was achieved within a short period of time (ca 4 h) for all herbicides. Sorption isotherms of the four herbicides were described by Freundlich equation with an r2 value > 0.98. The herbicide sorption as measured by the distribution coefficient (Kd) values ranged from 3.24 to 5.71 L/kg for diuron, 0.44 to 1.13 L/kg for fluometuron, 1.78 to 6.04 L/kg for prometryn and 0.22 to 0.59 L/kg for pyrithiobac-sodium. Sorption of herbicides was higher in the Moree soil than in Narrabri and Wee Waa soils. When the Kd values were normalised to organic carbon content of the soils (Koc), it suggested that the affinity of the herbicides to the organic carbon increased in the order: pyrithiobac-sodium < fluometuron < prometryn < or = diuron. The desorption isotherms were also adequately described by the Freundlich equation. For desorption, all herbicides exhibited hysteresis and the hysteresis was stronger for highly sorbed herbicides (diuron and prometryn) than the weakly sorbed herbicides (fluometuron and pyrithiobac-sodium). Hysteresis was also quantified as the percentage of sorbed herbicides which is not released during the desorption step (omega = [nad/nde - 1] x 100). Soil type and initial concentration had significant effect on omega. The effect of sorption and desorption properties of these four herbicides on the off-site transport to contaminate surface and groundwater are also discussed in this paper.     

Adsorption of methabenzthiazuron on six allophanic and nonallophanic soils: effect of organic matter amendment

This article reports on methabenzthiazuron [1-(1,3-benzothiazol-2-yl)-1,3-dimethylurea] (MBT) adsorption process on six agricultural allophanic and nonallophanic soils. The effect of amendment with exogenous organic matter was also studied. Adsorption kinetic fits an hyperbolic model. MBT adsorption reached an apparent equilibrium within 2 h and followed a second-order reaction. The maximum adsorbed amounts for natural soils ranged from 32 to 145 microg g(-1). Rate constants were considered relatively low (0.27-1.5 x 10(-4) [microg g(-1)](1-n) s-1); the slow process was attributed to a combined effect of difussion and adsorption. MBT adsorption fits the Freundlich model with r values > or =0.998 at P < or = 0.001 significance levels. Kf and Freundlich exponents (l/n) ranged from 5.3 to 82.1 cm3 g(-1) and from 0.66 to 0.73, respectively. Kf values for soils with a low organic matter content were lower than that obtained from the only typical allophanic soil derived from volcanic ash under study. Lineal regression analysis between Kf and organic matter content of nonallophanic soils gave a correlation coefficient of 0.980 (P = 0.02). Dispersion of Kd values together with close values of K(OM) indicate that organic matter (OM) was the principal component responsible for MBT adsorption in unamended soils. Addition of peat decreased soil pH and increased adsorption capacity for allophanic and nonallophanic soils. Kinetic experiments showed enhancements of Xmax values and lower rate constants.     

Sorption and leaching potential of acidic herbicides in Brazilian soils

Leaching of acidic herbicides (2,4-D, flumetsulam, and sulfentrazone) in soils was estimated by comparing the original and modified AF (Attenuation Factor) models for multi-layered soils (AFi). The original AFi model was modified to include the concept of pH-dependence for Kd (sorption coefficient) based on pesticide dissociation and changes in the accessibility of soil organic functional groups able to interact with the pesticide. The original and modified models, considering soil and herbicide properties, were applied to assess the leaching potential of selected herbicides in three Brazilian soils. The pH-dependent Kd values estimated for all three herbicides were observed to be always higher than pH-independent Kd values calculated using average Koc data, and therefore the original AFi model overestimated the overall leaching potential for the soils studied.     

The ratio of clay content to total organic carbon content is a useful parameter to predict adsorption of the herbicide butachlor in soils

Thirteen soils collected from 11 provinces in eastern China were used to investigate the butachlor adsorption. The results indicated that the total organic carbon (TOC) content, clay content, amorphous Fe2O3 content, silt content, CEC, and pH had a combined effect on the butachlor sorption on soil. Combination of the data obtained from the 13 soils in the present study with other 23 soil samples reported by other researchers in the literature showed that Koc would be a poor predictive parameter for butachlor adsorption on soils with TOC content higher than 4.0% and lower than 0.2%. The soils with the ratio of clay content to TOC content (RCO) values less than 60 adsorbed butachlor mainly by the partition into soil organic matter matrix. The soils with RCO values higher than 60 apparently adsorbed butachlor by the combination of the partition into soil organic matter matrix and adsorption on clay surface.     

Influence of heavy organic pollutants of anthropic origin on PAH retention by kaolinite.

The adsorption of heavy fuel oil No. 2 (F2) on a reference kaolinite (Arvor kaolin, France), and the influence of this anthropic organic matter on the phenanthrene (PHEN) retention capacity of a kaolinite were investigated in the laboratory. The heaviest and most polar compounds of F2 are adsorbed on kaolinite preferentially to the other compounds and also partly irreversibly. The precoating of kaolinite by F2 significantly increases the sorption of PHEN in the range of concentrations studied (10-500 microg l(-1)). The partition coefficients normalized to organic carbon content (Koc) of kaolin precoated with fuel oil (5.2 < log Koc < 5.5) are one order of magnitude higher than those of the original kaolin (4.2 < logKoc < 4.5), and show very good agreement with the literature for polluted industrial soils. The Koc measured on the uncoated kaolin are in close agreement with the values determined for natural soils in which humic substances represent the organic component. This demonstrates that the composition of organic matter is the primary factor in PHEN retention by the soils. Therefore, in predicting the transport of PHEN, and other Polycyclic aromatic hydrocarbons (PAHs) in general, in soils of industrial sites containing heavy hydrocarbons or tars requires that the specific nature of the organic matter contained in these soils be taken into consideration.     

Adsorption-desorption and leaching of pyraclostrobin in Indian soils

Pyraclostrobin is a new broad-spectrum foliar applied and seed protectant fungicide of the strobilurin group. In this paper, adsorption-desorption of pyraclostrobin has been investigated in three different soils viz. Inceptisol (sandy loam, Delhi), Vertisol (sandy clay, Hyderabad) and Ultisol (sandy clay loam, Thrissur). Effect of organic matter and clay content on sorption was also studied in Inceptisol of Delhi. Leaching potential of pyraclostrobin as influenced by rainfall was studied in intact soil columns to confirm the results of adsorption-desorption studies. The adsorption studies were carried out at initial concentrations of 0.05, 0.1, 0.5, 1 and 1.5 μg mL^?1. The distribution coefficient (K_d) values in three test soils ranged from 4.91 to 18.26 indicating moderate to high adsorption. Among the three test soils, adsorption was the highest in Ultisol (K_d 18.26), followed by Vertisol (K_d 9.87) and Inceptisol (K_d 4.91). K_F value was also highest for Ultisol soil (66.21), followed by Vertisol (40.88) and Inceptisol (8.59). S-type adsorption isotherms were observed in all the three test soils. K_d values in organic carbon-removed soil and clay-removed soil were 3.57 and 2.83 respectively, indicating lower adsorption than normal Inceptisol. Desorption studies were carried out at initial concentrations of 0.5, 1 and 1.5 μg mL^?1. Desorption was the greatest in Inceptisol, followed by Vertisol and Ultisol. Amounts of pyraclostrobin desorbed in three desorption cycles for different concentrations were 23.1–25.3%, 9.4–20.7% and 8.1–13.6% in Inceptisol, Vertisol and Ultisol respectively. Desorption was higher in clay fraction-removed and organic carbonremoved soils than normal Inceptisol. Desorption was slower than adsorption in all the test soils, indicating hysteresis effect (with hysteresis coefficient values varying from 0.05 to 0.20). Low values of hysteresis coefficient suggest high hysteresis effect indicating easy and strong adsorption, and slow desorption, of pyraclostrobin in soils. Higher hysteresis coefficient values in organic carbon removed soil (0.25–0.30) and clay fraction removed soil (0.28–0.36) as compared to normal Inceptisol soil suggest relatively weak adsorption and easy desorption of pyraclostrobin. Results of regression analysis suggest that the organic matter and pH of the soil play a major role in adsorption of pyraclostrobin. Leaching studies were carried out in intact soil columns in Inceptisol. The columns were leached with different amounts of water simulating different amounts of rainfall. The results suggest that most of the pyraclostrobin residues will remain present in the top soil layers even under high rainfall conditions and chances of pyraclostrobin moving to lower soil depth are almost negligible.     

Sorption of imidacloprid and its metabolites on tropical soils

The sorption of imidacloprid (1-[(6-chloro-3-pyridinyl)-methyl]-N-nitro-2-imidazolid-inimine ) (IMI) and its metabolites imidacloprid-urea (1-[(6-chloro-3-pyridinyl)-methyl]-2-imidazol-idinone) (IU), imidacloprid-guanidine (1-[(6-chloro-3-pyridinyl)-methyl]-4,5-dihydro-1H-imidazol-2-amine) (IG), and imidacloprid-guanidine-olefin (1-[(6-chloro-3-pyridinyl)methyl]-1H-imidazol-2-amine) (IGO) was determined on six typical Brazilian soils. Sorption of the chemicals on the soil was characterized using the batch equilibration method. The range and order of sorption (Kd) on the six soils was IG (4.75-134) > or = IGO (2.87-72.3) > IMI (0.55-16.9) > IU (0.31-9.50). For IMI and IU, Kd was correlated with soil organic carbon (OC) content and CEC, the latter due to the high correlation between OC and cation exchange capacity (CEC) (R2 = 0.98). For IG and IGO, there was no correlation of sorption to clay, pH, OC or CEC due to the high sorption on all soils. Average Koc values were IU = 170, IMI = 362, IGO = 2433, and IG = 3500. Although Kd and Koc values found were consistently lower than those found in soils developed in non-tropical climates, imidacloprid and its metabolites were still considered to be slightly mobile to immobile in Brazilian soils.     

Determination and analysis of sorption of 137Cs to soils in Hong Kong reservoir

Soils from a local reservoir had been analyzed for their physical and chemical properties, distribution coefficients Kd and sorption rates for 137Cs. It was found that soils in Hong Kong were relatively low in organic matter and more acidic than those in some other countries. In sorption experiments, the rates of decrease in water activity concentration were initially very high, higher for larger mass of soils added, and then slowed down. The larger the mass, the shorter was the time for equilibrium. Three isotherms had been obtained by varying one of the three parameters (initial water activity concentration, slurry ratio and particle size) at a time. For constant initial water activity concentration and random sizes, percent sorption increased with slurry ratio. For soils of constant mass and random sizes. percent sorption decreased with increasing initial water activity concentration. For constant initial water activity concentration and slurry ratio, percent sorption increased with decreasing size of soil particles. A simple logistic model was developed to explain some of the findings.     

Sorption of herbicides in relation to soil variability and landscape position

Using the soil-water sorption partitioning coefficient (Kd), this study quantified the spatial variation of 2,4-D sorption by soil in an undulating-to-hummocky terrain landscape near Minnedosa, MB, Canada. Herbicide sorption was most strongly related to soil organic matter content and slope position, with greatest sorption occurring in lower landscape positions with greater soil organic matter content. The relation between sorption and slope position was more pronounced under conventional tillage (CT) than under long-term zero-tillage (ZT). Using multivariate regression and three independent variables (soil organic matter content, soil clay content and soil pH), the prediction of herbicide sorption by soil was very good for CT (R2 = 0.89) and adequately for ZT (R2 = 0.53).     

Calculating pesticide sorption coefficients (Kd) using selected soil properties

Pesticide soil/solution distribution coefficients ( Kd values), commonly referred to as pesticide soil sorption values, are utilized in computer and decision aid models to predict soil mobility of the compounds. The values are specific for a given chemical in a given soil sample, normally taken from surface soil, a selected soil horizon, or at a specific soil depth, and are normally related to selected soil properties. Pesticide databases provide Kd values for each chemical, but the values vary widely depending on the soil sample on which the chemicals were tested. We have correlated Kd values reported in the literature with the reported soil properties for an assortment of pesticides in an attempt to improve the accuracy of a Kd value for a specific chemical in a soil with known soil properties. Mathematical equations were developed from regression equations for the related properties. Soil properties that were correlated included organic matter content, clay mineral content, and/or soil pH, depending on the chemical properties of the pesticide. Pesticide families for which Kd equations were developed for 57 pesticides include the following: Carboxy acid, amino sulfonyl acid, hydroxy acid, weakly basic compounds and nonionizable amide/anilide, carbamate, dinitroaniline, organochlorine, organophosphate, and phenylurea compounds. Mean Kd values for 32 additional pesticides, many of which had Kd values that were correlated with specific soil properties but for which no significant Kd equations could be developed are also included.     

Sorptive behavior of the phenylamide fungicides,mefenoxam and metalaxyl,and their acid metabolite in typical Cameroonian and German soils

Laboratory soil sorption experiments were conducted on mefenoxam, formulated metalaxyl (F-metalaxyl), pure metalaxyl (P-metalaxyl) and metalaxyl acid metabolite to elucidate differences in their sorptive behaviour on typical Cameroonian forest soil (sand clay loam, pH 4.8 and 3.01% OC) and German soil (sandy loam, pH 7.2, 1.69% OC) using a batch equilibrium method. The data obtained on all test chemicals conformed to linear and Freundlich adsorption isotherms. The Langmuir equation failed to describe the sorption of the substances tested. All substances were adsorbed to a greater extent by the Cameroonian soil. The average percentage adsorptions for mefenoxam, F-metalaxyl, P-metalaxyl and the acid metabolite on the Cameroonian soil were 27.8%, 28.3%, 31.8% and 46.8% respectively while for the German soil they were 21.7%, 21.5%, 24.7% and 9.8% respectively. The KD and KF parameters and the Freundlich exponential term (1/n) were low, indicating that the interactions between soil particles and the fungicides were weak. The sorption parameters were lower in the German soil. P-metalaxyl exhibited a higher adsorption capacity than F-metalaxyl in both soils. Mefenoxam and F-metalaxyl exhibited similar sorption parameters in soils, whereas those of P-metalaxyl and acid metabolite differed. Differences observed in the adsorption between the two soils could be attributed to their properties. Desorption studies revealed that the adsorbed fungicides were not firmly retained by soil particles and their adsorption was reversible. Desorption of adsorbed mefenoxam, P-metalaxyl and of the acid metabolite from German soil was almost completely reversible with percentage desorption rates of more than 91.0%, whereas the rate for F-metalaxyl was 74.1%. All compounds exhibited some resistance to desorption from the Cameroonian soil, with percentage desorption rates less than 77.0%. Therefore if degradation in the soil is slow the fungicides described have a potential to leach to lower soil horizons.     

Adsorption behavior of RH‐5992 insecticide onto sandy and clay loam forest soils

Abstract

Adsorption‐desorption behavior of RH‐5992 [Mimic®, N'‐t‐butyl‐N'‐(3,5‐dimethylbenzoyl)‐N‐(4‐ethylbenzoyl) hydrazine] in sandy and clay loam forest soils was studied using the batch equilibrium method. Adsorption was higher in the clay loam soil than in the sandy loam, and increased linearly with RH‐5992 concentration, but decreased with increasing pH and temperature. The adsorption data fit better to the Freundlich, than to the Langmuir equation. The K_D (linear adsorption constant) and K_F (Freundlich constant) were similar for each soil at 5, 15 and 25°C and decreased with increase of temperature, indicating that the enthalpy of adsorption was negative. The exponent of the Freundlich equation was close to unity for both soils at all three temperatures. The low E_a (energy of activation) indicated a diffusion‐controlled process during the initial stages of adsorption. The desorption isotherm differed from that of adsorption, and the linear desorption constant, K_D(d), was ca 25 times higher than the K_D, indicating that adsorption of RH‐5992 was not readily reversible. Evaluation of thermo‐dynamic parameters confirmed the presence of strong bonds between the solute and soil. These findings suggest that RH‐5992 has a limited potential for downward mobility leading to groundwater contamination.