石油污染土壤中芘高效降解菌群的筛选及降解特性研究

从长期受石油污染土壤中驯化筛选到能以芘为惟一碳源生长的混合菌群GP3,其主要由假单胞菌株GP3A(Pseudomonas sp.)和菌株GP3B(Pandoraea pnomenusa)组成.采用摇瓶振荡培养方法,研究了不同环境条件对混合菌GP3降解芘效能的影响.结果表明,在30℃,150 r/min振荡培养下,混合菌GP3对15 mg/L芘的7 d降解率为90.6%.混合菌GP3降解芘的最适宜温度为35℃,最佳pH值为6.2.加入低浓度葡萄糖(100 mg/L)或菲(10 mg/L)作为共代谢底物,均可提高GP3对芘的降解率.混合菌对芘的降解速率(PDR)与芘的初始浓度呈正相关.研究重金属离子胁迫下GP3对芘的降解时发现,10 ms/L Zn2 的存在对芘降解效能影响较小,Cu2 对芘的降解有抑制作用,Cd2 对混合菌GP3有很强的毒性.     

一株芘降解菌B2的降解条件优化及降解基因

芳香烃降解菌是石油污染土壤修复的主要生物资源。采用芘平板升华法对克拉玛依原油污染土壤样品进行驯化培养,分离得到一株芘降解菌B2,经16S rDNA基因序列比对及系统发育进化分析表明,该菌株为假单胞菌属(Pseudo-monas)。采用正交设计方法优化菌株B2对高分子量多环芳烃芘的降解条件,并构建多元非线性模型预测菌株B2对芘的最佳降解条件,结果表明:在接种量OD660 nm为0.60、降解温度为40℃、降解时间为6.0 d时,预测菌株B2对芘的降解最大达到38.214 mg/L,实际测得最大降解量为37.906 mg/L,预测准确率为99.19%。运用PCR技术克隆B2的邻苯二酚-2,3-双加氧酶基因(B2C23O)(I.2.A亚家族),核酸序列分析表明,该基因全长880 bp,具有一个完整的开放阅读框,编码246个氨基酸,与已报道的Pseudomonas putida W619同源性最高为97%;对B2C23O基因编码氨基酸序列进行分析,发现其具有邻位断裂双加氧酶模式结构,推测菌株B2通过邻位裂解途径降解芘代谢中间产物邻苯二酚。     

菌源对多环芳烃降解菌的筛选及降解性能的影响

高效降解菌的筛选对利用生物修复技术有效去除环境中的多环芳烃具有重要意义。分别以石油污染土壤和焦化废水活性污泥为菌源,分离出芘降解菌和混合PAHs(菲、荧蒽和芘)降解菌共14株并对其降解性能进行对比研究。结果表明,筛选得到的菌株分别属于9个菌属,其中2种菌源共有的菌属为Mycobacterium sp.、Ralstonia sp.和Shinella sp.。芘和PAHs的高效降解菌(CP16和CM32)均属于分支杆菌属(Mycobacterium),来源于焦化废水活性污泥;菌株CP16对芘(50mg/L)的7 d降解率为74.99%,CM32对PAHs(菲50 mg/L、荧蒽和芘各10 mg/L)的7 d降解率为100%。因此,以焦化废水活性污泥为菌源更有利于获得高效的多环芳烃降解菌。     

降解菌ZQ5与紫茉莉对芘污染土壤的联合修复

在温室盆栽条件下,通过单独种植紫茉莉、单独接种多环芳烃(PAHs)模式化合物芘的专性降解菌ZQ5和两者的联合修复的3种处理,对芘污染土壤的修复效果进行了研究。结果表明,经90 d修复后,植物-微生物联合修复可将人工污染土壤中的芘降解81.1%,将石油污染土壤中的芘降解50.3%,其修复效率明显高于其他2种处理,是紫茉莉修复的1.98倍,是降解菌ZQ5修复的1.39倍。ZQ5的不同接菌量对于修复60 d后的降解率影响不大。外源生物修复条件下,10～20 cm土壤的修复效率要高于5 cm土壤;自然降解条件下,5 cm土层降解率略高于其他土层。     

一株芘的高效降解菌的选育及其降解性能研究

旨在为多环芳烃污染环境的生物修复提供微生物资源和科学依据,从某焦化厂曝气池的活性污泥中分离纯化出一株降解芘的优势菌株B-1,该菌株可在以芘为惟一碳源的培养基中生长繁殖,能利用芘的最高浓度为130 mg/L左右.经形态学观察、生理生化实验及l6S rDNA序列分析,初步判断菌株B-1为芽胞杆菌属.投菌量、芘初始浓度、pH...     

芘降解菌DY-1的条件优化及降解动力学特性分析

选用已筛选出以芘为唯一碳源的假单胞菌DY-1(Pseudomonas sp.)作为芘降解菌,采用摇瓶振荡培养方法,研究了不同环境条件对菌DY-1降解芘效率的影响以及降解动力学特性。结果表明,在含芘50 mg/L的条件下培养9 d,降解率达83.2%。最适宜温度为30℃,pH值为7.5,摇床转速为120 r/min,接种量为1.5 mL;在不同培养条件下芘的降解符合一级动力学模型;低浓度Zn2+,Cd2+,Cr6+的存在对芘降解效果影响较小,Cu2+,Pb2+对芘的降解有较强的毒性;加入低浓度有机物质,蔗糖可提高DY-1芘的降解;低浓度萘或蒽的存在可促进芘的降解。     

一株多环芳烃降解菌的筛选及其降解特性

微生物修复是治理土壤多环芳烃(polycyclic aromatic hydrocarbons, PAHs)污染的主要方法,而高效降解菌筛选是微生物修复技术的重要基础。从北京焦化厂土壤中筛选分离得到一株PAHs降解菌Q3,通过生理生化和16S rDNA等分析手段鉴定其为Rhodococcus rhodochrous。结果表明:该菌株对芘的耐受能力较强,可降解初始浓度为200 mg·L~(-1)的芘;该菌株具有降解广谱性,可利用苯并[a]芘、苯并[b]荧蒽、二苯并[a,h]蒽、苯并[g,h,i]苝等9种PAHs为唯一碳源进行代谢,特别是对苯并[a]芘等高环PAHs具有较好的降解效果;此外,该菌株可有效降解模拟液中的混合PAHs,并且对野外被PAHs长期污染的土壤具有较好的强化修复效果。投加菌株处理后的处理组与对照组相比,土壤PAHs总去除率提高了24%。以上结果表明该菌株对环境中被PAHs污染的土壤具有较好的强化修复潜力,可为PAHs污染土壤的微生物修复技术提供技术参考。     

盐环境下降解菌群对芘的降解特性研究

以芘为多环芳烃(PAHs)的代表物,利用1.0%盐度的无机盐培养基从石油污染土壤中富集出高效嗜盐PAHs降解菌群。通过DNA测序鉴定,菌群中对芘起重要降解作用的是Rhodanobacter、Pseudomonas、Mycobacterium,3者碱基比例达到31.82%。14d内,萘、菲、荧蒽、芘、苯并[a]芘5种PAHs的挥发损耗均可忽略不计。筛选得到的菌群降解芘的最佳条件为:酵母粉质量浓度为120mg/L,盐度不超过1.0%,无需额外添加甲基-β-环糊精。筛选出的降解菌群对芘的最佳降解条件可用于降解萘、菲、荧蒽和苯并[a]芘等其他PAHs,但随着PAHs环数增加,分子量增大,降解率降低。在最佳条件下降解14d时,萘、菲、荧蒽、芘、苯并[a]芘5种PAHs的降解率可分别达100.00%、85.48%、51.92%、56.28%、50.45%。     

芘高效降解菌ZQ_5的培养条件及无机元素对其降解效率的影响

以从我国最大的石油污水灌区之一——沈抚灌区污染土壤分离到的以芘为惟一碳源、能源生长的高效降解菌株ZQ5为实验材料,通过对菌株ZQ5培养条件的优化,以及采用摇瓶振荡培养方法测定菌株ZQ5对不同浓度芘的降解率,表明：菌株ZQ5在30℃振荡培养16 d后对150 mg/L芘的降解率为90.31%。通过模拟稻田施用N、P和K肥等的土壤环境,探索了无机营养元素对降解菌ZQ5降解能力的影响,发现土壤中混合加入N、P和K无机营养元素的降解率能达到82%以上,比单加某种营养元素对降解菌ZQ5的降解效果好。本研究结果可以指导稻田PAHs的原位生物修复。     

大豆、龙葵单作和间作对芘污染土壤的修复

土壤多环芳烃(PAHs)污染控制是当前土壤污染防治与保护的热点问题。采用室内盆栽实验,选择PAHs中具有代表性的四环化合物芘(Pyrene)作为研究对象,研究了大豆、龙葵单作和间作对不同浓度芘污染土壤的修复效果。结果表明:低浓度的芘(10 mg/kg)在一定程度上促进了大豆的生长,而高浓度的芘(250 mg/kg)则对大豆的生长有抑制作用;龙葵的生长没有受到芘污染(10~250 mg/kg)的影响;间作对大豆、龙葵的生长均有不同程度的促进作用。污染物芘在大豆和龙葵(成熟期)中的分布情况是:地下部分地上部分;间作并未对大豆、龙葵中的芘含量造成显著影响。同一污染水平下,不同种植模式的修复效果为:大豆-龙葵间作大豆单作龙葵单作无植物对照。因此,大豆-龙葵间作是一种既能有效修复芘污染土壤,又能充分利用污染土地资源的修复模式。     

Dioxin- and POP-contaminated sites—contemporary and future relevance and challenges

BACKGROUND, AIM AND SCOPE: Once they have been generated, polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs) and other persistent organic pollutants (POPs) can persist in soils and sediments and in waste repositories for periods extending from decades to centuries. In 1994, the US EPA concluded that contaminated sites and other reservoirs are likely to become the major source of contemporary pollution problems with these substances. With this in mind, this article is the first in a new series in ESPR under the title 'Case Studies on Dioxin and POP Contaminated Sites--Contemporary and Future Relevance and Challenges', which will address this important issue. The series will document various experiences from sites contaminated with PCDD/F and other POPs. This article provides an overview of the content of the articles comprising the series. In addition, it provides a review of the subject in its own right and identifies the key issues arising from dioxin/POP-contaminated sites. Additionally, it highlights the important conclusions that can be drawn from these examples. The key aim of this article and of the series as a whole is to provide a comprehensive overview of the types of PCDD/F contaminated sites that exist as a result of historical activities. It details the various processes whereby these sites became contaminated and attempts to evaluate their contemporary relevance as sources of PCDD/Fs and other POPs. It also details the various strategies used to assess these historical legacies of contamination and the concepts developed, or which are under development, to effect their remediation. MAIN FEATURES: Special sessions on 'Contaminated sites--Cases, remediation, risk and policy' were held at the DIOXIN conferences in 2006 and 2007, and this theme will be continued at DIOXIN 2008 to be held in Birmingham. Selected cases from the approximately 70 contributions made to these sessions, together with some additional invited case studies are outlined together with the key issues they raise. By evaluating these cases and adding details of experiences published in the current literature, an overview will be given of the different features and challenges of dioxin and POP-contaminated sites. RESULTS: This article provides a systematic categorisation of types of PCDD/F and POP-contaminated sites. These are categorised according to the chemical or manufacturing process, which generated the PCDD/Fs or POPs and also includes the use and disposal aspects of the product life cycle in question. The highest historical PCDD/F and dioxin-like polychlorinated biphenyl (PCB) contamination burdens have arisen as a result of the production of chlorine and of chlorinated organic chemicals. In particular, the production of chlorinated pesticides, PCBs and the related contaminated waste streams are identified being responsible for historical releases of toxic equivalents (TEQs) at a scale of many tonnes. Along with such releases, major PCDD/F contaminated sites have been created through the application or improper disposal of contaminated pesticides, PCBs and other organochlorine chemicals, as well through the recycling of wastes and their attempted destruction. In some extreme examples, PCDD/F contaminated sites have also resulted from thermal processes such as waste incinerators, secondary metal industries or from the recycling or deposition of specific waste (e.g. electronic waste or car shredder wastes), which often contain chlorinated or brominated organic chemicals. The examples of PCDD/F and dioxin-like PCB contamination of fish in European rivers or the impact of contaminated sites upon fishing grounds and upon other food resources demonstrate the relevance of these historical problems to current and future human generations. Many of the recent food contamination problems that have emerged in Europe and elsewhere demonstrate how PCDD/F and dioxin like PCBs from historical sources can directly contaminate human and animal feedstuffs and indeed highlight their considerable contemporary relevance in this respect. Accordingly, some key experiences and lessons learnt regarding the production, use, disposal and remediation of POPs from the contaminated sites are summarised. DISCUSSION: An important criterion for evaluating the significance and risks of PCDD/Fs and other POPs at contaminated sites is their present or future potential for mobility. This, in turn, determines to a large degree their propensity for off-site transport and environmental accessibility. The detailed evaluation of contaminated site cases reveals different site-specific factors, which influence the varied pathways through which poor water-soluble POPs can be mobilised. Co-contaminants with greater water solubility are also typically present at such sites. Hence, pumping of groundwater (pump and treat) is often required in addition to attempting to physically secure a site. At an increasing number of contaminated sites, securing measures are failing after relatively short time spans compared to the time horizon, which applies to persistent organic pollutant contamination. Due to the immense costs and challenges associated with remediation of contaminated sites 'monitored natural attenuation' is increasingly gaining purchase as a conceptual remediation approach. However, these concepts may well prove limited in their practical application to contaminated sites containing persistent organic pollutants and other key pollutants like heavy metals. CONCLUSIONS: It is inevitable, therefore, that dioxin/POP-contaminated sites will remain of contemporary and future relevance. They will continue to represent an environmental issue for future generations to address. The securing and/or remediation of dioxin/POP-contaminated sites is very costly, generally in the order of tens or hundreds of millions of dollars. Secured landfills and secured production sites need to be considered as constructions not made for 'eternity' but built for a finite time scale. Accordingly, they will need to be controlled, supervised and potentially repaired/renewed. Furthermore, the leachates and groundwater impacted by these sites will require ongoing monitoring and potential further remediation. These activities result in high maintenance costs, which are accrued for decades or centuries and should, therefore, be compared to the fully sustainable option of complete remediation. The contaminated site case studies highlight that, while extensive policies and established funds for remediation exist in most of the industrialised western countries, even these relatively well-regulated and wealthy countries face significant challenges in the implementation of a remediation strategy. This highlights the fact that ultimately only the prevention of contaminated sites represents a sustainable solution for the future and that the Polluter Pays Principle needs to be applied in a comprehensive way to current problems and those which may emerge in the future. RECOMMENDATIONS AND PERSPECTIVES: With the continuing shift of industrial activities in developing and transition economies, which often have poor regulation (and weak self-regulation of industries), additional global challenges regarding POPs and other contaminated sites may be expected. In this respect, a comprehensive application of the "polluter pays principle" in these countries will also be a key to facilitate the clean-up of contaminated areas and the prevention of future contaminated sites. The threats and challenges of contaminated sites and the high costs of securing/remediating the problems highlight the need for a comprehensive approach based upon integrated pollution prevention and control. If applied to all polluting (and potentially polluting) industrial sectors around the globe, such an approach will prove to be both the cheapest and most sustainable way to underpin the development of industries in developing and transition economies.     

Persistence and dissipation kinetics of trifloxystrobin and tebuconazole in onion and soil

The persistence and dissipation kinetics of trifloxystrobin and tebuconazole on onion were studied after application of their combination formulation at a standard and double dose of 75 + 150 and 150 + 300 g a.i. ha^?1. The fungicides were extracted with acetone, cleaned-up using activated charcoal (trifloxystrobin) and neutral alumina (tebuconazole). Analysis was carried out by gas chromatograph (GC) and confirmed by gas chromatograph mass spectrometry (GC-MS). The recovery was above 80% and limit of quantification (LOQ) 0.05 mg kg^?1 for both fungicides. Initial residue deposits of trifloxystrobin were 0.68 and 1.01 mg kg^?1 and tebuconazole 0.673 and 1.95 mg kg^?1 from standard and double dose treatments, respectively. Dissipation of the fungicides followed first-order kinetics and the half life of degradation was 6–6.6 days. Matured onion bulb (and field soil) harvested after 30 days was free from fungicide residues. These findings suggest recommended safe pre-harvest interval (PHI) of 14 and 25 days for spring onion consumption after treatment of Nativo 75 WG at the standard and double doses, respectively. Matured onion bulbs at harvest were free from fungicide residues.     

Sorption and Desorption Behavior of Chloroanilines and Chlorophenols on Montmorillonite and Kaolinite

The bioavailability of pollutants, pesticides and/or their degradation products in soil depends on the strength of their sorption by the different soil components, particularly by the clay minerals. This study reports the sorption-desorption behavior of the environmentally hazardous industrial pollutants and certain pesticides degradation products, 3-chloroaniline, 3,4-dichloroaniline, 2,4,6-trichloroaniline, 4-chlorophenol, 2,4-dichlorophenol and 2,4,6-trichlorophenol on the reference clays kaolinite KGa-1 and Na-montmorillonite SWy-l. In batch studies, 2.0 g of clay were equilibrated with 100.0 mL solutions of each chemical at concentrations ranging from 10.0 to 200.0 mg/L. The uptake of the compounds was deduced from the results of HPLC-UV-Vis analysis. The lipophilic species were best retained by both clay materials. The most lipophilic chemical used in the study, 2,4,6-trichloroaniline, was also the most strongly retained, with sorption of up to 8 mg/g. In desorption experiments, which also relied on HPLC-UV-Vis technique, 2,4,6-trichloroaniline was the least desorbed from montmorillonite. However, on kaolinite all of the compounds under study were irreversibly retained. The experimental data have been modelled according to the Langmuir and Freundlich isotherms. A hypothesis is proposed concerning the sorption mechanism and potential applications of the findings in remediation strategies have been suggested.     

Field and laboratory studies of the fate and enantiomeric enrichment of venlafaxine and O-desmethylvenlafaxine under aerobic and anaerobic conditions

The stereoselectivity of R,S-venlafaxine and its metabolites R,S-O-desmethylvenlafaxine, N-desmethylvenlafaxine, O,N-didesmethylvenlafaxine, N,N-didesmethylvenlafaxine and tridesmethylvenlafaxine was studied in three processes: (i) anaerobic and aerobic laboratory scale tests; (ii) six wastewater treatment plants (WWTPs) operating under different conditions; and (iii) a variety of wastewater treatments including conventional activated sludge, natural attenuation along a receiving river stream and storage in operational and seasonal reservoirs. In the laboratory and field studies, the degradation of the venlafaxine yielded O-desmethylvenalfaxine as the dominant metabolite under aerobic and anaerobic conditions. Venlafaxine was almost exclusively converted to O-desmethylvenlafaxine under anaerobic conditions, but only a fraction of the drug was transformed to O-desmethylvenlafaxine under aerobic conditions. Degradation of venlafaxine involved only small stereoisomeric selectivity. In contrast, the degradation of O-desmethylvenlafaxine yielded remarkable S to R enrichment under aerobic conditions but none under anaerobic conditions. Determination of venlafaxine and its metabolites in the WWTPs agreed well with the stereoselectivity observed in the laboratory studies. Our results suggest that the levels of the drug and its metabolites and the stereoisomeric enrichment of the metabolite and its parent drug can be used for source tracking and for discrimination between domestic and nondomestic wastewater pollution. This was indeed demonstrated in the investigations carried out at the Jerusalem WWTP.     

Synthesis and characterization of m- and p-methylbenzyl-mercapturic acids derived from m- and p-xylenes

Chemical synthesis and physical properties of two mercapturic acids suggested as urinary metabolites of m- and p-xylenes ace described. These compounds may be used for the identification and quantivative determination by high-performance liquid chromatography of the corresponding mercapturic acids in urine.     

Levels of PCDDs and PCDFs in products and effluent from the Swedish pulp and paper industry and chloralkali process

Within the Swedish Dioxin Survey various samples from the pulp and paper industry and the chloralkali process have been analyzed by congener specific analytical methods. In addition to the generally discussed “bleaching pattern” of the tetrachlorinated congeners, these samples also contained higher chlorinated congeners like hexa-CDDs, hepta-CDFs, octa-CDD and octa-CDF. Consequently it is recommended that samples from the pulp industry should be analyzed for all PCDDs and PCDFs (tetra- through octa-). Counted as Nordic Toxic Equivalents (NTEQ), the recycled pulp samples had the highest contamination level followed by TMP, unbleached sulfite and bleached softwood and hardwood. In addition to the bleaching process, various chemicals used in the pulping, bleaching and wastewater treatment can contribute to the contamination.     

Uptake and translocation of metformin, ciprofloxacin and narasin in forage- and crop plants

Transfer of bioactive organic compounds from soil to plants might represent animal and human health risks. Sewage sludge and manure are potential sources for bioactive compounds such as human- and veterinary drugs. In the present study, uptake of the anti-diabetic compound, metformin, the antibiotic agent ciprofloxacin and the anti-coccidial narasin in carrot (Daucuscarota ssp. sativus cvs. Napoli) and barley (Hordeumvulgare) were investigated. The pharmaceuticals were selected in order to cover various chemical properties, in addition to their presence in relevant environmental matrixes. The root concentration factors (RCF) found in the present study were higher than the corresponding leaf concentration factors (LCF) for the three test pharmaceuticals. The uptake of metformin was higher compared with ciprofloxacin and narasin for all plant compartments analyzed. Metformin was studied more explicitly with regard to uptake and translocation in meadow fescue (Festucapratense), three other carrot cultivars (D.carota ssp. sativus cvs. Amager, Rothild and Nutri Red), wheat cereal (Triticumaestivum) and turnip rape seed (Brassicacampestris). Uptake of metformin in meadow fescue was comparable with uptake in the four carrot cultivars (RCF 2-10, LCF approximately 1.5), uptake in wheat cereals were comparable with barley cereals (seed concentration factors, SCF, 0.02-0.04) while the accumulation in turnip rape seeds was as high as 1.5. All three pharmaceuticals produced negative effects on growth and development of carrots when grown in soil concentration of 6-10 mg kg⁻¹ dry weight.     

Copper-catalyzed chlorination and condensation of acetylene and dichloroacetylene

The chlorination and condensation of acetylene at low temperatures is demonstrated using copper chlorides as chlorinated agents coated to model borosilicate surfaces. Experiments with and without both a chlorine source and borosilicate surfaces indicate the absence of gas-phase and gas-surface reactions. Chlorination and condensation occur only in the presence of the copper catalyst. C₂ through C₈ organic products were observed in the effluent; PCDD/F were only observed from extraction of the borosilicate surfaces. A global reaction model is proposed that is consistent with the observed product distributions. Similar experiments with dichloroacetylene indicate greater reactivity in the absence of the copper catalyst. Reaction is observed in the gas-phase and in the presence of borosilicate surfaces at low temperatures. The formation of hexachlorobenzene is only observed in the presence of a copper catalyst. PCDD/F were only observed from extraction of the borosilicate surfaces. A global reaction model is proposed for the formation of hexachlorobenzene from dichloroacetylene.     

Aerobic and anaerobic degradation of profluralin and trifluralin

Abstract

The degradation of profluralin [N‐(cyclopropylmethyl)‐α,α,α‐trifluoro‐2,6‐dinitro‐N‐propyl‐]p‐toluidine] and trifluralin (α,α,α‐trifluoro‐2,6‐dinitro‐N,N‐dipropyl‐p‐toluidine) was studied under aerobic and anaerobic soil conditions. Three soils (Goldsboro loamy sand, Cecil loamy sand, Drummer clay loam) were each treated with 1 ppmw herbicide; anaerobic conditions were maintained by flooding. Soil samples were extracted monthly and subjected to TLC analysis. No degradation was detected in sterile controls. Aerobic degradation of both herbicides was greatest in the Cecil loamy sand soil over the entire incubation period. Degradation of profluralin in Cecil soil under aerobic conditions was 86 percent after 4 months with three products detected; 83 percent of the trifluralin was degraded with two products detected. Anaerobic degradation accounted for 72 percent of the profluralin and 78 percent of the trifluralin after 4 months. Degradation of both herbicides increased with incubation time for the first 3 months and decreased slightly thereafter. Generally there was more extensive degradation (percent and in number of products formed) of profluralin than trifluralin under the conditions tested. More degradation products were detected for both herbicides under aerobic conditions than under anaerobic conditions.     

Sources and distribution of polychlorinated-dibenzo-p-dioxins and -dibenzofurans in soil and sediment from the Yellow Sea region of China and Korea

Polychlorinated-dibenzo-p-dioxins and -dibenzofurans (PCDD/Fs) were measured in soils and sediments from the Yellow Sea region. Korean soils and sediments mostly contained detectable PCDD/Fs and showed a widespread distribution among locations. Soil and sedimentary PCDD/Fs from China were comparable to or less than those in Korea. The patterns of relative concentrations of individual congeners in soils were different between the two countries, but similar in sediments. Sources of PCDD/Fs in China and Korea were found to be independent of each other and their distributions reflected matrix-dependent accumulation. Spatial distribution indicated some point sources in Korea while Chinese sources were more widespread and diffuse. PCDD/Fs measured in the coastal areas of the Yellow Sea were comparable to or less than those previously reported in for eastern Asia. However, ∑TEQs in soils and sediments were near to or, in some cases exceeded environmental quality guidelines.