Siting a municipal solid waste disposal facility,Part II: The effects of external criteria on the final decision

The procedure of a multi-criteria decision analysis supported by the geographic information systems was applied to the site selection process of a planning municipal solid waste management practice based on twelve different scenarios. The scenarios included two different decision tree modes and two different weighting models for three different area requirements. The suitability rankings of the suitable sites obtained from the application of the decision procedure for the scenarios were assessed by a factorial experimental design concerning the effect of some external criteria on the final decision of the site selection process. The external criteria used in the factorial experimental design were defined as “Risk perception and approval of stakeholders” and “Visibility”. The effects of the presence of these criteria in the decision trees were evaluated in detail. For a quantitative expression of the differentiations observed in the suitability rankings, the ranking data were subjected to ANOVA test after a normalization process. Then the results of these tests were evaluated by Tukey test to measure the effects of external criteria on the final decision. The results of Tukey tests indicated that the involvement of the external criteria into the decision trees produced statistically meaningful differentiations in the suitability rankings. Since the external criteria could cause considerable external costs during the operation of the disposal facilities, the presence of these criteria in the decision tree in addition to the other criteria related to environmental and legislative requisites could prevent subsequent external costs in the first place.

Implications:

An experimental design was applied to a siting process based on different scenarios. The suitability rankings of suitable sites were obtained for each scenario. The external criteria used in the design were defined as perception and visibility. The presence of the external criteria produced meaningful differentiations. Two widespread persuasions about site selection were disproved using the results.     

Systematic screening of common wastewater-marking pharmaceuticals in urban aquatic environments: implications for environmental risk control

In this report, we refer to pharmaceuticals that are widespread in the urban aquatic environment and that mainly originate from wastewater treatment plants or non-point source sewage as “wastewater-marking pharmaceuticals” (WWMPs). To some extent, they reflect the condition or trend of water contamination and also contribute to aquatic environmental risk assessment. The method reported here for screening typical WWMPs was proposed based on academic concerns about them and their concentrations present in the urban aquatic environment, as well as their properties of accumulation, persistence, eco-toxicity and related environmental risks caused by them. The screening system consisted of an initial screening system and a further screening system. In the former, pharmaceuticals were categorised into different evaluation levels, and in the latter, each pharmaceutical was given a normalised final evaluation score, which was the sum of every score for its properties of accumulation, persistence, eco-toxicity and environmental risk in the aquatic environment. The system was applied to 126 pharmaceuticals frequently detected in the aquatic environment. In the initial screening procedure, five pharmaceuticals were classified into the “high” category, 16 pharmaceuticals into the “medium” category, 15 pharmaceuticals into the “low” category and 90 pharmaceuticals into the “very low” category. Subsequently, further screening were conducted on 36 pharmaceuticals considered as being of “high”, “medium” and “low” categories in the former system. We identified 7 pharmaceuticals with final evaluation scores of 1–10, 10 pharmaceuticals with scores of 11–15, 15 pharmaceuticals with scores from 16 to 20 and 4 pharmaceuticals with scores above 21. The results showed that this screening system could contribute to the effective selection of target WWMPs, which would be important for spatial-temporal dynamics, transference and pollution control of pharmaceuticals in the urban aquatic environment. However, there remains a number of pharmaceutical parameters with measured data gaps, such as organic carbon adsorption coefficients and bioconcentration factors, which, if filled, would improve the accuracy of the screening system.     

Understanding regional metabolism for a sustainable development of urban systems

Cities are the most complex forms of settlements which man has built in the course of his cultural development. Their “metabolism” is connected with the world economy and is run mainly by fossil energy carriers. Up to now there are no validated models for the evaluation of a sustainable development of urban regions. The guidelines for a “sustainable development” suggest the reduction of resource consumption. The article is concerned with the problem of how the “sustainable-development concept” can be transformed from a global to a regional scale. In urban settlements the strategy of final storage should be applied. By this, the subsystem waste management can be transformed within 10 to 15 years to a “sustainable status”. With regard to the system “agronomy”, the article concludes that agriculture in urban systems should focus on food production instead of promoting reduction of food production in favour of energy plants, which is not a suitable strategy. The main problems are the energy carriers. Transformation to a “sustainble status” is only possible by a reconstruction of the urban system, i.e. of buildings and the transportation network. The rate determining step in achieving such a status is the change in the fabric of buildings and in the type of transportation networks. The reconstruction of an urban system needs, mainly for economical reasons, a time period of two generations.     

Knowledge domain and emerging trends of carbon footprint in the field of climate change and energy use: a bibliometric analysis

Carbon footprint (CF) research has attained tremendous popularity for improving the climate environment purposes. In particular, current energy use has been identified as the main cause of climate change. CF plays an irreplaceable role in managing energy use, reducing gas emissions, and improving climate change. The objective of this study was to review studies that have developed CF and to perform a bibliometric analysis using two key terms: “climate change” and “energy use”. From bibliometric analysis using CiteSpace and VOSviewer, it was possible to establish a knowledge map of cooperative network structure and research evolution. We are aiming to reveal the main logical chain of CF research leading to climate change, to make up for the lack of current literature, and provide research inspiration for researchers. The research findings mainly focus on four aspects. First, the relevant research began in 2008 and is in a state of continuous rise. Second, due to the law of research development and the prominence of practical problems, related research has experienced a stage from conceptual methods to specific problems. Third, China and the USA assume an important role in which international cooperation is the overall trend. Fourth, related research can be divided into CF algorithm research, ecological environment management research, and specific cross-industry fields. In addition, possible opportunities for change in related research are explored. It is also suggested that the integration of CF with other footprints, when energy use and environmental change are fully considered, may become an important future research trend by providing a more comprehensive environmental impact.

     

A Reexamination of the Ozone Limiting Approach to Estimating Short-Term NO2 Concentrations

The partition and effective diffusion coefficients of formaldehyde were measured for three materials (conventional gypsum wallboard, “green” gypsum wallboard, and “green” carpet) under three relative humidity (RH) conditions (20%, 50%, and 70% RH). The “green” materials contained recycled materials and were friendly to environment. A dynamic dual-chamber test method was used. Results showed that a higher relative humidity led to a larger effective diffusion coefficient for two kinds of wallboards and carpet. The carpet was also found to be very permeable resulting in an effective diffusion coefficient at the same order of magnitude with the formaldehyde diffusion coefficient in air. The partition coefficient (K _ma) of formaldehyde in conventional wallboard was 1.52 times larger at 50% RH than at 20% RH, whereas it decreased slightly from 50% to 70% RH, presumably due to the combined effects of water solubility of formaldehyde and micro-pore blocking by condensed moisture at the high RH level. The partition coefficient of formaldehyde increased slightly with the increase of relative humidity in “green” wallboard and “green” carpet. At the same relative humidity level, the “green” wallboard had larger partition coefficient and effective diffusion coefficient than the conventional wallboard, presumably due to the micro-pore structure differences between the two materials. The data generated could be used to assess the sorption effects of formaldehyde on building materials and to evaluate its impact on the formaldehyde concentration in buildings.

Implications: Based on the results of this study, the sink effects of these commonly used materials (conventional and “green” gypsum wallboards, “green” carpet) on indoor formaldehyde concentration could be estimated. The effects of relative humidity on the diffusion and partition coefficients of formaldehyde were found to differ for materials and for different humidity levels, indicating the need for further investigation of the mechanisms through which humidity effects take place.     

Methodology for the Study of Public Attitudes Concerning Air Pollution

A significant element of a community's total air pollution picture is the “state of mind” of the people living in the area with respect to air pollution. The reasons why a study of public attitudes can be an important factor in planning an air pollution control program are briefly summarized. The methodology applied in one such study in the St. Louis Metropolitan area is described, and possible variations related to different scope, objectives and survey area characteristics are suggested.     

Effects of herbicide stress on wheat cultivars from organic and conventional cropping systems

Abstract

Wheat (Triticum aestivum L.) seedlings grown from seeds produced in “organic”; (non‐chemical) and “conventional”; cropping systems are characterized by a) similar rates of root and shoot growth, b) equal sensitivity to phytotoxicity by the herbicide glyphosate, and c) equivalent basal activity of the enzyme glutathione S‐transferase (both in the roots and in the shoots). In addition, treatment of these seedlings with glyphosate leads to significantly higher contents of this enzyme both in the shoots and in the roots. However, time‐course and dose‐response investigations indicate significant differences in the induction pattern of glutathione S‐transferase: the response of “conventional”; wheat seedlings takes place earlier and with higher efficiency, than that of the “organic”; ones.     

Distribution of Light Hydrocarbons in Ambient Air

The diversity of hydrocarbons which are present in ambient polluted air provide a potentially rich source of information concerning the nature of this type of pollution. Measurements of the relative amounts of various hydrocarbons can be correlated with the various possible sources. Since hydrocarbon reactivities vary widely it is also possible to estimate the extent to which various individual hydrocarbons have reacted. Except for samples taken deliberately near sources of hydrocarbon pollution these air samples invariably resemble auto exhaust with an addition of natural gas and of C₃–C₅ paraffins which resemble gasoline vapor. Samples taken in industrial areas and near the smoke plume from a brush fire showed distinctive differences in composition. During the smog season in the fall of 1968 good data were obtained of “typical” or “representative” samples of light, medium and heavy smog. These show the expected depletion of more reactive hydrocarbons in a much more convincing way than before. By comparing these distributions with composition in unreacted samples and by making use of data from bottle irradiations, it was possible to estimate the contribution of the various hydrocarbons in terms of “amount reacted.” The amounts of higher hydrocarbons present and reacted were also estimated from gasoline composition.     

Design of Sampling Schedules

Concern with the statistical precision associated with certain pollutant sampling schedules led to comparison of two sampling schemes, designated as “modified random” and “systematic” sampling methods. A nearly uninterrupted body of data representing six years of sampling provided a basis from which to perform hypothetical “sampling” by the two methods. Comparison of results shows that the systematic method generally gave better results. The method is very simple; ft entails the selection of a sampling interval (other than 7 days or multiple of 7), the selection (randomly) of an initial sampling date, and regular sampling at the selected interval thereafter.     

Errors in Measurement and Counting of Particles Using Light Scattering

More efficient air sampling programs can be designed, and clearer interpretations of their data made, if important theoretical aspects are clearly understood. The choice of a sampling time is an important decision affecting the results. Empirical and theoretical calculations show that the averaging effect of sampling time attenuates responses to short period fluctuations in pollutant concentrations. Data for sulfur dioxide concentrations in six cities are examined.

The body acts as a sampling mechanism also, and concentrations inside the body fluctuate less than those outside. These damping processes are quantitatively described. A significant biological parameter is the product of the biological half-life of a pollutant and the fraction of entrance to total resistance for its passage through the body. When sampling time is four times this parameter, attenuation of significant fluctuations is about the same in both samples and the body; when it is twice the parameter, the “sampling window” transmits all significant fluctuations better than the “biological window.” Shorter sampling periods appear to give unnecessary fine detail for biological application according to this theoretical model.     

Chemical speciation of individual atmospheric particles using low-Z electron probe X-ray microanalysis:: characterizing “Asian Dust” deposited with rainwater in Seoul,Korea

Chemical speciation of individual microparticles is of much interest in environmental atmospheric chemistry; e.g. the determination of the elemental concentrations in individual atmospheric aerosol particles is important to study the chemical behavior of atmospheric pollution. Recently, an EPMA technique using an X-ray detector equipped with an ultra-thin window, allowing EPMA to determine concentrations of low-Z elements, such as C, N, and O, in individual particles of micrometer size, has been developed. This technique, called low-Z electron probe X-ray microanalysis (low-Z EPMA), is applied to characterize the water-insoluble part of “Asian Dust”, deposited by washout in the form of rainwater during an Asian Dust storm event and collected in Seoul, Korea. In this study, it was demonstrated that the single particle analysis using low-Z EPMA provided detailed information on various types of chemical species in the sample. In addition to aluminosilicates, silicon oxide, iron oxide, and calcium carbonate particles, which are expected to be present, carbonaceous particles are also observed in a significant fraction. This unexpected finding that particle sample originated from an arid area contains significant amount of carbonaceous particles is supported by the investigation of a “China Loess” sample. In addition, we also performed single particle analysis for a local soil sample, in order to check the possible influence from local sources on “Asian Dust”. The characteristics of the local soil particle sample, e.g. the types of aluminosilicate particles and the abdundance of particles with deviating chemical species, are clearly different from “Asian Dust” and “China Loess” samples, whereas those two are similar, implying that the “Asian Dust” sample was not much influenced by local sources.     

Air Quality Modeling and Decisions for Ozone Reduction Strategies

Abstract

Despite the widespread application of photochemical air quality models (AQMs) in U.S. state implementation planning (SIP) for attainment of the ambient ozone standard, documentation for the reliability of projections has remained highly subjective. An “idealized” evaluation framework is proposed that provides a means for assessing reliability. Applied to 18 cases of regulatory modeling in the early 1990s in North America, a comparative review of these applications is reported. The intercomparisons suggest that more than two thirds of these AQM applications suffered from having inadequate air quality and meteorological databases. Emissions representations often were unreliable; uncertainties were too high. More than two thirds of the performance evaluation efforts were judged to be substandard compared with idealized goals. Meteorological conditions chosen according regulatory guidelines were limited to one or two cases and tended to be similar, thus limiting the extent to which public policy makers could be confident that the emission controls adopted would yield attainment for a broad range of adverse atmospheric conditions. More than half of the studies reviewed did not give sufficient attention to addressing the potential for compensating errors. Corroborative analyses were conducted in only one of the 18 studies reviewed. Insufficient attention was given to the estimation of model and/or input database errors, uncertainties, or variability in all of the cases examined. However, recent SIP and policy‐related regional modeling provides evidence of substantial improvements in the underlying science and available modeling systems used for regulatory decision making. Nevertheless, the availability of suitable databases to support increasingly sophisticated modeling continues to be a concern for many locations. Thus, AQM results may still be subject to significant uncertainties. The evaluative process used here provides a framework for modelers and public policy makers to assess the adequacy of contemporary and future modeling work.     

Air pollutant emissions associated with forest,grassland, and agricultural burning in Texas

Outdoor fires, such as wildfires and prescribed burns, can emit substantial amounts of particulate matter and other pollutants into the atmosphere. In Texas, an inventory of forest, grassland and agricultural burning activities revealed that fires consumed vegetation on 1.6 and 1.7 million acres of land, in 1996 and 1997, respectively. Emissions from the fires were estimated based on survey and field data on acres burned and land cover and literature data on fuel consumption and emission factors. Fire data were allocated spatially by county and temporally by month. While fire events can cause high transient air pollutant concentrations, for most criteria pollutants, the fire emissions were a relatively small fraction of the annual emission inventory for the State. For fine particulate matter, however, the annual emission estimates were 40,000 tons/yr, which is likely to represent a significant fraction of the State's emission inventory, especially in the counties where the emissions are concentrated.     

A cheap protocol for colour measure and for diagnostic in planning a cultural heritage restoration. Case study: main façade of Palazzo Governi (Cagliari,Sardinia, Italy)

Due to the bad state of conservation, “Palazzo Governi”, a seventeenth-century building located in the old town district of “Stampace” in Cagliari (Sardinia, Italy), was subjected to restoration. Thus, according to the Italian Law n. 1089, the main façade colour must be reproduced, and therefore, its identification was required. The available samples looked fairly degraded, in particular as an easy plaster to crumble; so, some other analyses able to identify the degradation cause were performed. Two different approaches were adopted to attain the first goal, the visual colour assessment by a sensory panel (subjective) and the instrumental measurement by colorimetry (objective). Ion chromatography and inductively coupled plasma–optical emission spectroscopy analyses, as well as conductivity and pH measurements, were performed to evaluate the presence of water-soluble salts inside the plaster, as possible cause of degradation; the binder/aggregate ratio was also evaluated. A full mineralogical and petrographic characterisation of the materials constituting the samples, as well as the identification of their stratigraphy and some other morphologic and structural features suitable to highlight eventual forms of degradation, were performed by optical microscopy. Scanning electron microscopy coupled to X-ray microanalysis was been also used in order to confirm and/or to integrate data obtained by optical microscopy. The samples have been compared with two samples coming from two other buildings, also located in Sardinia, that looked in good conservation state. The results evidenced that the causes of degradation come from a high salt (especially sulphate) content and a scarce presence of binder in the plaster that can be imputed to a wrong initial composition and/ or to a leaching by acidic rain.     

Mobile Air Quality Monitoring Systems: Present Problems and Future Needs

This overview represents much of the discussion and summarizes many of the concerns emerging from the recent APCA Specialty Conference, “In-Situ Air Quality Monitoring from Moving Platforms.”

Users of mobile air quality monitoring systems have been hampered in their attempts to generate dependable data because of a lack of suitable instrumentation. Most equipment used in mobile systems was designed for laboratory or stationary monitoring applications and cannot cope well with the harsh environment encountered in aircraft or other mobile platforms. Only through innovative modifications have investigators been able to utilize off-the-shelf equipment. The technology exists, however, for manufacturers to build a much higher quality product if only a market incentive could be created.

This paper outlines problem areas which need to be addressed in the production of reliable “mobile quality” instrumentation, and suggests some market incentives.     

Effects of Variable Vehicular Age and Classification Distributions in Mobile Source Modeling

Jackson Hole Airport is the only air carrier airport located entirely in a National Park, that being Grand Teton. Concerns over noise impacts led to an Airport/Park agreement setting allowable levels, restricting flights and flight paths, and calling for compliance monitoring in the noise sensitive areas. This study documented seven days of continuous noise level measurements made at four sites in the Park during four consecutive seasons in 1985-86. Individual sound exposure level measurements at B-737/200 jets, Swearingen Metro turboprops, and general aviation aircraft permitted computation of “aircraft-only” day/night levels (DNL) at each site for each day. Measurement of half-hourly average sound levels permitted computation of “total” DNL for comparisons. Results showed general compliance with the DNL limits, except when winds necessitated northerly departures, in which case a single B- 737 could cause an exceedance. There were no statistically significant differences in mean aircraft DNL for each site over the seasons, largely because of high variances. At the more remote sites, the total DNL was generally not established by airport activity, but by the 10-dB nighttime DNL penalty added to background levels generated by wind or water. The newer B- 737/300 aircraft, introduced to Jackson in the winter of 1986, were observed to be noticeably quieter on departure.     

Exploring the metal phytoremediation potential of three <Emphasis Type="Italic">Populus alba</Emphasis> L. clones using an in vitro screening

Purpose  

This work was planned for providing a useful screening tool for the selection of Populus alba clones suitable for phytoremediation techniques. To this aim, we investigated variation in arsenic, cadmium, copper, and zinc tolerance, accumulation and translocation in three poplar clones through an in vitro screening. Poplars have been widely proposed for phytoremediation, as they are adaptable to grow on contaminated areas and able to accumulate metals. The investigation of possible differences among poplar clones in metal tolerance and accumulation deserves to be deeply studied and exploited for the selection of the more suitable tool for phytoremediation purposes.     

At the Crossroads

ABSTRACT

Modeling transit bus emissions and fuel economy requires a large amount of experimental data over wide ranges of operational conditions. Chassis dynamometer tests are typically performed using representative driving cycles defined based on vehicle instantaneous speed as sequences of “microtrips”, which are intervals between consecutive vehicle stops. Overall significant parameters of the driving cycle, such as average speed, stops per mile, kinetic intensity, and others, are used as independent variables in the modeling process. Performing tests at all the necessary combinations of parameters is expensive and time consuming. In this paper, a methodology is proposed for building driving cycles at prescribed independent variable values using experimental data through the concatenation of “microtrips” isolated from a limited number of standard chassis dynamometer test cycles. The selection of the adequate “microtrips” is achieved through a customized evolutionary algorithm. The genetic representation uses microtrip definitions as genes. Specific mutation, crossover, and karyotype alteration operators have been defined. The Roulette-Wheel selection technique with elitist strategy drives the optimization process, which consists of minimizing the errors to desired overall cycle parameters. This utility is part of the Integrated Bus Information System developed at West Virginia University.

IMPLICATIONS It is expected that the paper will provide a useful tool for modeling and analysis of vehicle fuel economy and emissions and for the design, optimization, and analysis of driving cycles for testing and vehicle fleet management.     

A Probability Model for Evaluating Building Contamination from an Environmental Event

ABSTRACT

Asbestos dust and bioaerosol sampling data from suspected contaminated zones in buildings allowed development of an environmental data evaluation protocol based on the differences in frequency of detection of a target contaminant between zones of comparison. Under the assumption that the two test zones of comparison are similar, application of population proportion probability calculates the significance of observed differences in contaminant levels. This was used to determine whether levels of asbestos dust contamination detected after a fire were likely the result of smoke-borne contamination, or were caused by pre-existing/background conditions.

Bioaerosol sampling from several sites was also used to develop the population proportion probability protocol. In this case, significant differences in indoor air contamination relative to the ambient conditions were identified that were consistent with the visual observations of contamination. Implicit in this type of probability analysis is a definition of “contamination” based on significant differences in contaminant levels relative to a control zone. Detection of a suspect contaminant can be assessed as to possible sources(s) as well as the contribution made by pre-existing (i.e., background) conditions, provided the test and control zones are subjected to the same sampling and analytical methods.     

Information Required for the Selection and Performance Evaluation of Wet Scrubbers

The term “wet scrubber” or simply “scrubber,” for the purpose of this report, is intended to include any device using liquid to effect the removal of solid or liquid particles which are entrained in process air or gas streams. This guide is intended to provide information required for the selection and performance evaluation of all types of scrubbers installed for the primary purpose of removing such particulates from any process gas stream. It is not intended to cover scrubbers for the collection of gaseous and/or vapor constituents which involve gas absorption mechanisms.