首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 93 毫秒
1.
以可燃垃圾、污水污泥和煤粉为原料,添加园林残余、固硫剂等按L16(45)正交表配料,采用机械成型设备制备固废复合燃料,研究燃料组分对固硫固氯效果的影响。固硫率、固氯率实验数据的极差、方差分析结果显示:CaO添加量对固硫率、固氯率的影响最显著;MnO2添加量对固氯率的影响仅次于CaO添加量,但对固硫率没有影响。运用ForStat 2.0统计软件建立了固硫率、固氯率指标的预测方程,置信度大于95%。应用综合评分法筛选出最佳固硫固氯效果的燃料制备配方为:A2B3C2D3,即垃圾、污泥、煤粉以2∶1∶1比例混合,园林残余为10%,助燃剂MnO2添加量为0.17%,固硫剂CaO添加1.2%时所制备的燃料,燃烧中固硫率可达74.55%,固氯率可达77.35%。  相似文献   

2.
目前的城市污水处理厂剩余污泥热值的测定主要参考煤热值的测定方法。根据污泥的特性,对热值测定过程中污泥的干燥方式、助燃剂的影响和热值校正计算3个方面进行了优化研究。结果表明,冷冻干燥(-50℃)能够避免污泥有机物的挥发,从而精确地测定剩余污泥的热值;对于有机物含量较高的污泥(VS/TS>0.57),不添加助燃剂也能准确测定污泥的热值;通过测定氧弹洗液中硫酸和硝酸的含量来计算热值校正,从而准确得到污泥的热值。  相似文献   

3.
在(35±0.2)℃温度下,以餐厨垃圾和剩余污泥为原料,设置餐厨垃圾和剩余污泥混合比例(VS)分别为1∶0、2∶1、1∶1、1∶2和0∶1,研究其单独消化与混合消化的系统性能、产甲烷潜力及脱氢酶活性和F420浓度变化。结果表明,混合消化提高了系统稳定性,与餐厨垃圾单独消化相比,添加剩余污泥能调节pH、氨氮浓度和VFA浓度,缩短产气周期;与剩余污泥单独消化相比,添加餐厨垃圾能显著提高沼气产量。混合比例为1∶1组混合消化产甲烷潜力最佳,消化作用的协同效应最为明显,沼气和甲烷产量分别达358.2 mL/g VS和224.1 mL/g VS,较餐厨垃圾和污泥单独消化估计值分别提高了23.09%和36.80%。1∶1混合消化组脱氢酶活性最高达437.33 TFμg/(mL·h),比餐厨垃圾和剩余污泥单独消化分别提高93.60%和40.69%,辅酶F420浓度最高为1.718μmol/L,分别提高17.3%和100.7%。  相似文献   

4.
改性凹凸棒粘土脱硫剂脱除SO2   总被引:2,自引:1,他引:1  
采用单因素法,在传统搅拌混合下,研究了煅烧温度、煅烧时间、酸碱浸渍等对改性凹凸棒粘土脱硫剂穿透硫容与最大硫容的影响.然后在超声波混合作用下,采用正交实验确定了超声时间、超声温度以及活性组分(CaO)、促进剂(V2O5)的复配比例.结果表明:(1)甘肃临泽凹凸棒粘土富Al、Mg、Fe,且其比表面积较大.(2)改性凹凸棒粘土脱硫剂最佳制备条件:煅烧温度300℃;煅烧时间2.0 h;酸碱浸渍最佳pH9~10;混合采用超声波,超声时间30 min;超声温度40℃;CaO质量分数30%;V2O5质量分数5%.采用在最佳条件下制备的改性凹凸棒粘土脱硫剂进行脱除SO2实验,其最大硫容为38.16%.(3)改性凹凸棒粘土脱除SO2的性能比工业Fe2O3脱硫剂强.(4)X射线衍射分析表明,改性凹凸棒粘土脱硫剂脱除SO2后,将SO2转变为SO2-4,从而达到完全脱除SO2的目的,这与红外光谱分析的结果一致.  相似文献   

5.
张生芹  谢兵 《环境工程学报》2012,6(11):4157-4161
采用热力学计算和实验方法对钙硫比n(CaO)/n(S)=2.0条件下不同钙基固硫剂的固硫效果进行了比较,发现:CaO的固硫效率最高。以CaO为固硫剂,研究了添加剂MnO2对CaO固硫效果的影响。结果表明,加入MnO2可以提高CaO的固硫效率,且其含量为1%时对CaO固硫的促进效果最佳。这是因为煤粉燃烧过程中MnO2将逐级分解,分解产物依次为Mn2O3和Mn3O4,锰的氧化物一方面可以催化CaO的固硫反应,另一方面,Mn3O4本身也参与到固硫反应之中,生成MnSO4,从而促进钙基固硫剂的固硫效果。  相似文献   

6.
消化污泥作为垃圾填埋场覆盖材料的研究   总被引:4,自引:0,他引:4  
为解决城市污染,实现污泥"减量化、无害化、稳定化、资源化"的目标,有必要寻求更多技术上可行、低成本的污泥综合利用新技术.测定了消化污泥本底的含水率、有机质含量以及经过预处理后不同含水率的消化污泥模拟降雨实验的渗透系数,浸出液的COD、氨氮、pH等.选择渗透系数低、污染负荷小的含水率为50%和60%的消化污泥,分别与石灰、炉渣以不同比例混合改性后,再测定模拟降雨实验浸出液的各个指标.实验结果表明,含水率为60%的消化污泥与炉渣以2∶1(质量比)混合时,渗透系数达到10-6数量级,已接近垃圾填埋场对防渗层的要求.因此,消化污泥改性后可作为垃圾填埋场覆盖材料.  相似文献   

7.
为探索生活垃圾催化热解液体产物特性变化规律,选取Na2CO3、CaO、Fe2O33种催化剂,利用固定床实验、红外分析(FT-IR)进行生活垃圾热解液体产物产率和组分特性研究.结果表明,热解终温600℃无催化剂时,生活垃圾热解液产率为39.80 wt%,添加3种催化剂后热解液产率均降低;生活垃圾分别添加1%的Na2CO3和CaO后,热解油氧含量由22.49%分别降低到20.12%和18.53%,低位热值由30.30 MJ/kg分别提高到33.79和32.74 MJ/kg;无催化剂时热解油成分为脂肪类、含氧化合物及少量芳香类混合物,加催化剂后热解油中芳香类物质峰面积比例显著增加,而含氧化合物峰面积比例降低,羟基类及羧酸类含氧化合物峰面积比例明显减少,其他含氧物峰面积比例却增加;CaO催化效果较明显,生活垃圾添加1%的CaO热解油中芳香类物质峰面积比例从4.36%增加到29.46%,含氧化合物峰面积比例由49.42%降低到23.12%,其中羟基类和羧酸类化合物峰面积比例分别由34.03%和10.65%降低到0.00%和3.34%,其他含氧化合物峰面积比例由4.73%增加到19.77%.  相似文献   

8.
新型复合垃圾衍生燃料的制备及性能分析   总被引:1,自引:0,他引:1  
为了提高城市生活垃圾资源化利用的效率,采用室温冷压有粘结剂成型的方法将城市生活垃圾和煤按一定的配比制成新型复合垃圾衍生燃料,研究了成型压力、配比对衍生燃料的热稳定性、机械强度、粘结性以及发热量的影响.试验结果表明,在生活垃圾中加入煤可有效改善衍生燃料性能,增加其热值,在成型压力为25 MPa,煤配比为20%时复合衍生燃料的性能最优.  相似文献   

9.
采用自制的生物干化实验装置,以高含水率混合收集生活垃圾为研究对象,探讨了不同C/N比(15、20.7、24.6和30)对垃圾生物干化效果的影响,比较了4组干化产物的RDF产率和产品性质。结果表明,不同C/N比垃圾生物干化理化性质与脱水效果存在明显差异;低C/N比处理的pH、NH_3挥发率均大于高C/N处理。C/N比为20.7垃圾生物干化效果最佳,在这种比例下处理的含水率下降幅度、垃圾水分去除率、单位有机物脱水能力和低位热值增幅均大于其他处理组。经过12 d生物干化,不同C/N比垃圾含水率分别下降了16.5%、20.3%、13%和15.4%,干化产物低位热值同比原生垃圾增长了78.3%、114.5%、65.8%和79.0%,达到了垃圾经济性焚烧要求,其硫、氯元素含量低于0.5%,重金属的含量也在可以合理范围内,可作为RDF燃料制备原料。  相似文献   

10.
钢铁厂冷轧废水污泥中含有10%以上的铬、20%以上的铁和1.5%以上的锌(均以质量分数计).为了从污泥中回收铬,首先研究了污泥中铬的形态,确定为Cr(Ⅲ);然后以碳酸钠为氧化助剂,将污泥与碳酸钠按一定比例混合后焙烧,再用水浸取.研究了碳酸钠的添加量、焙烧温度和时间、浸取时间和浸取方式对铬回收率的影响.研究表明,每克干污泥中添加0.6 g或以上碳酸钠,在固定床上700 ℃焙烧4 h以上,可实现60%以上的总铬浸出率,残渣为Fe2O3基脱硫剂原料.  相似文献   

11.
介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠  相似文献   

12.
Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.  相似文献   

13.
The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.  相似文献   

14.
造纸废水混凝处理中SFT助凝替代性研究   总被引:1,自引:0,他引:1  
中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染  相似文献   

15.
寻找廉价而高效的替代原料是实现生物柴油产业化的关键所在.微藻以含油量高、生长周期短、环境适应能力强、生物产量高等优点,有望成为一种极具潜力的生物柴油生产原料.然而,目前尚存在微藻培养低效成本高和微藻回收效率低两大难题.综述了微藻培养与回收过程中的关键技术,并对存在的两大难题及其改进技术进行了详细的探讨.最后,总结并展望了微藻培养、回收技术未来的发展趋势.  相似文献   

16.
Evaluation of the presence of drugs of abuse in tap waters   总被引:1,自引:0,他引:1  
A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L−1, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L−1. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L−1). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L−1 (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L−1, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L−1). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L−1 (Spain) and 0.3 ng L−1 (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.  相似文献   

17.
不同泥源对厌氧氨氧化反应器启动的影响   总被引:2,自引:1,他引:1  
李祥  黄勇  袁怡  张丽  朱莉 《环境工程学报》2012,6(7):2143-2148
采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。  相似文献   

18.
Biodegradation mechanisms were elucidated for three dibenzoate plasticizers: diethylene glycol dibenzoate (D(EG)DB), dipropylene glycol dibenzoate (D(PG)DB), both of which are commercially available, and 1,6-hexanediol dibenzoate, a potential green plasticizer. Degradation studies were done using Rhodococcus rhodochrous in the presence of pure alkanes as a co-substrate. As expected, the first degradation step for all of these systems was the hydrolysis of one ester bond with the release of benzoic acid and a monoester. Subsequent biodegradation of the monobenzoates of diethylene glycol (D(EG)MB) and dipropylene glycol (D(PG)MB) was very slow, leading to significant accumulation of these monoesters. In contrast, 1,6-hexanediol monobenzoate was quickly degraded and characterization of the metabolites indicated that the biodegradation proceeded by way of the oxidation of the alcohol group to generate 6-(benzoyloxy) hexanoic acid followed by β-oxidation steps. This pathway was blocked for D(EG)MB and D(PG)MB by the presence of an ether function.The use of a pure hydrocarbon as a co-substrate resulted in the formation of another class of metabolites; namely the esters of the alcohols formed by the oxidation of the alkanes and the benzoic acid released by hydrolysis of the original diesters. These metabolites were biodegraded without the accumulation of any intermediates.  相似文献   

19.
影响混凝效果的因素众多,混凝沉淀烧杯试验是进行水的混合、絮凝、沉淀工艺研究、设计和生产指导的最有效方法之一,阐述了智能型混凝试验搅拌器的设计原理和技术性能.  相似文献   

20.
以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径<1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号