凹凸棒土对腐殖酸的低温吸附性能研究

首次研究凹凸棒土对饮用水中腐殖酸的低温吸附性能,考察5℃条件下,吸附时间与腐殖酸初始浓度、吸附剂投加量、pH对凹凸棒土吸附腐殖酸的影响,确定吸附剂的吸附等温线、吸附动力学和热力学等相关理论参数,研究凹凸棒土对腐殖酸的吸附性能与机理。结果表明,江苏盱眙凹凸棒土在温度5℃、pH=4、水中腐殖酸初始浓度为5 mg/L,投加量为15 g/L的条件下,吸附180 min后对腐殖酸的去除率可达97.26%。凹凸棒土对腐殖酸的吸附符合二级吸附动力学方程与Freundlich吸附等温式,吸附过程由孔隙内扩散过程控制,吸附为自发的吸热过程,包括物理吸附与化学吸附。根据Fre-undlich吸附等温式拟合计算,5℃、pH=7时理论最大吸附量为9 mg/g,说明凹凸棒土对于低温饮用水中腐殖酸具有良好的吸附效果。     

Removal of organic polyelectrolytes and their metal complexes by adsorption onto xonotlite

Natural organic polyelectrolytes (humic and fulvic acids) and their metal complexes were removed by adsorption onto xonotlite. The removal percentages of humic and fulvic acids by xonotlite were approximately 80% and 30%, respectively. Humic acid removal from solution by adsorption onto xonotlite took place more readily than fulvic acid removal. The molecular weight distributions of the humic substances remaining in solution after adsorption with the xonotlite were measured with size exclusion chromatography. A comparison of molecular weight distributions demonstrated conclusively that large molecular weight components were adsorbed preferentially, indicating that adsorption efficiency depends on the number of functional groups of humic substances. Furthermore, the surface topography of the adsorbent was observed before and after adsorption by scanning electron microscopy. The calculated heat of adsorption was of 330 kJ mol(-1) which was evaluated from the Clapeyron-Clausius equation. Therefore, the adsorption type can be considered chemical. Since xonotlite can be easily synthesized and obtained at low cost, the adsorption method of humic and fulvic acids is superior to their precipitation.     

Simultaneous removal of potent cyanotoxins from water using magnetophoretic nanoparticle of polypyrrole: adsorption kinetic and isotherm study

Cyanotoxins, microcystins and cylindrospermopsin, are potent toxins produced by cyanobacteria in potable water supplies. This study investigated the removal of cyanotoxins from aqueous media by magnetophoretic nanoparticle of polypyrrole adsorbent. The adsorption process was pH dependent with maximum adsorption occurring at pH 7 for microcystin-LA, LR, and YR and at pH 9 for microcystin-RR and cylindrospermopsin (CYN). Kinetic studies and adsorption isotherms reflected better fit for pseudo-second-order rate and Langmuir isotherm model, respectively. Thermodynamic calculations showed that the cyanotoxin adsorption process is endothermic and spontaneous in nature. The regenerated adsorbent can be successfully reused without appreciable loss of its original capacity.     

Purification of industrial phosphoric acid (54 %) using Fe-pillared bentonite

The current problem of excess impurities in industrial phosphoric acid (IPA) 54 % P₂O₅ makes phosphates industries look toward low-cost but efficient adsorbents. In the present study, iron-oxide-modified bentonite (Fe-PILB) was prepared and investigated as a possible adsorbent for the removal of organic matter (OM) like humic acid (HA), chromium (Cr(III)), and zinc (Zn(II)) from IPA aqueous solutions. These adsorbents were characterized using XRD, TEM, and BET. The adsorption of impurities is well described by the pseudo-second-order model. The results indicate that Fe-PILB has a good ability to resist co-existing anions and the low-pH condition of IPA and owns a relatively high-removal capacity of 80.42 and 25 % for OM, Cr(III), and Zn(II). The mechanism of adsorption may be described by the ligand and ion exchange that happened on the active sites. The selected order of adsorption OM?>?Cr³⁺?>?Zn²⁺ showed the importance of the competitive phenomenon onto bentonite materials’ pore adsorption. For the adsorption of OM at the low pH of IPA, H-bond complexation was the dominant mechanism. From the adsorption of heavy metals and OM complex compounds contained in IPA 54 % on Fe-PILB, the bridging of humic acid between bentonite and heavy metals (Zn(II) or Cr(III)) is proposed as the dominant adsorption mechanism (bentonite-HA-Me). Overall, the results obtained in this study indicate Fe-pillared bentonite possesses a potential for the practical application of impurity (OM, Zn(II), and Cr(III)) removal from IPA aqueous solutions.     

褐煤对废水中酸性红B的吸附去除

选用褐煤作为廉价吸附剂,脱除模拟废水中染料酸性红B。研究了褐煤对废水中酸性红B的吸附动力学、等温吸附模式,考察了pH、褐煤投加量以及离子强度(NaCl)对吸附效果的影响。结果表明,吸附动力学较好地符合准二级速率方程(R2=1.000),并且以化学吸附为主;吸附等温式满足Langmuir方程(R2=0.986),最大单分子层吸附量为42 mg/g;废水中染料的去除率随溶液pH的减小而明显增加,在pH=1时,去除效果最好,证实吸附过程存在静电吸引及化学键合;在一定条件下,溶液中酸性红B的去除率随褐煤投加量增加而增加;吸附效果随溶液中离子强度(NaCl)的增加而增强。说明褐煤可以作为一种廉价吸附材料,用于处理含染料废水。     

Removal of PAHs from water using an immature coal (leonardite)

It has been studied an immature coal (leonardite) as an adsorbent for removing PAHs [fluorene, pyrene, benzo(k)fluoranthene, benzo(a)pyrene and benzo(g,h,i)perylene] from water. To determine the efficiency of leonardite as an adsorbent of PAHs, factors such as pH, contact time and equilibrium sorption were evaluated in a series of batch experiments. There were no significant differences in the removal percentages for the various pH values studied, except for fluorene. The adsorption of fluorene was higher at lower pH values. The equilibrium time was reached at 24h. At this time, more than 82% of the pyrene, benzo(k)fluoranthene, benzo(a)pyrene and benzo(g,h,i)perylene had been removed. During the first 2h, the adsorption rate increased rapidly. After that time, however, there was a minor decrease. Equilibrium data were fitted to Freundlich models to determine the water-leonardite partitioning coefficient. Physical adsorption caused by the aromatic nature of the compounds was the main mechanism that governed the removal process. The polarity of the humic substances in leonardite may also have influenced the adsorption capacity.     

Preparation and characterization of surfactant-modified hydroxyapatite/zeolite composite and its adsorption behavior toward humic acid and copper(II)

A novel composite material, i.e., surfactant-modified hydroxyapatite/zeolite composite, was used as an adsorbent to remove humic acid (HA) and copper(II) from aqueous solution. Hydroxyapatite/zeolite composite (HZC) and surfactant-modified HZC (SMHZC) were prepared and characterized by X-ray diffraction, Fourier transform infrared spectroscopy, and field emission scanning electron microscope. The adsorption of HA and copper(II) on SMHZC was investigated. For comparison purposes, HA adsorption onto HZC was also investigated. SMHZC exhibited much higher HA adsorption capacity than HZC. The HA adsorption capacity for SMHZC decreased slightly with increasing pH from 3 to 8 but decreased significantly with increasing pH from 8 to 12. The copper(II) adsorption capacity for SMHZC increased with increasing pH from 3 to 6.5. The adsorption kinetic data of HA and copper(II) on SMHZC obeyed a pseudo-second-order kinetic model. The adsorption of HA and copper(II) on SMHZC took place in three different stages: fast external surface adsorption, gradual adsorption controlled by both film and intra-particle diffusions, and final equilibrium stage. The equilibrium adsorption data of HA on SMHZC better fitted to the Langmuir isotherm model than the Freundlich isotherm model. The equilibrium adsorption data of copper(II) on SMHZC could be described by the Langmuir, Freundlich, and Dubinin–Radushkevich isotherm models. The presence of copper(II) in solution enhanced HA adsorption onto SMHZC. The presence of HA in solution enhanced copper(II) adsorption onto SMHZC. The mechanisms for the adsorption of HA on SMHZC at pH 7 may include electrostatic attraction, organic partitioning, hydrogen bonding, and Lewis acid–base interaction. The mechanisms for the adsorption of copper(II) on SMHZC at pH 6 may include surface complexation, ion exchange, and dissolution–precipitation. The obtained results indicate that SMHZC can be used as an effective adsorbent to simultaneously remove HA and copper(II) from water.     

Evaluating of arsenic(V) removal from water by weak-base anion exchange adsorbents

Arsenic contamination of groundwater has been called the largest mass poisoning calamity in human history and creates severe health problems. The effective adsorbents are imperative in response to the widespread removal of toxic arsenic exposure through drinking water. Evaluation of arsenic(V) removal from water by weak-base anion exchange adsorbents was studied in this paper, aiming at the determination of the effects of pH, competing anions, and feed flow rates to improvement on remediation. Two types of weak-base adsorbents were used to evaluate arsenic(V) removal efficiency both in batch and column approaches. Anion selectivity was determined by both adsorbents in batch method as equilibrium As(V) adsorption capacities. Column studies were performed in fixed-bed experiments using both adsorbent packed columns, and kinetic performance was dependent on the feed flow rate and competing anions. The weak-base adsorbents clarified that these are selective to arsenic(V) over competition of chloride, nitrate, and sulfate anions. The solution pH played an important role in arsenic(V) removal, and a higher pH can cause lower adsorption capacities. A low concentration level of arsenic(V) was also removed by these adsorbents even at a high flow rate of 250–350 h^?1. Adsorbed arsenic(V) was quantitatively eluted with 1 M HCl acid and regenerated into hydrochloride form simultaneously for the next adsorption operation after rinsing with water. The weak-base anion exchange adsorbents are to be an effective means to remove arsenic(V) from drinking water. The fast adsorption rate and the excellent adsorption capacity in the neutral pH range will render this removal technique attractive in practical use in chemical industry.     

Removal of humic substances from water by means of calcium-ion-enriched natural zeolites.

The ability of the natural zeolited Neapolitan Yellow Tuff (NYT) enriched with calcium ions to remove humic acids from water was evaluated by batch adsorption equilibrium tests and dynamic experiments carried out by percolating humic acid solutions through a small NYT column (breakthrough curves). Under the experimental condition explored, the sorption capacity increases with the ionic strength and has the highest value at pH 7.4. The partition coefficient for a low concentration of humic acid ([humic acid] --> 0), at pH 7.4 in 0.01 M sodium chloride, was approximately 1000 L/kg, versus the value of approximately 100 L/kg in the absence of the alkaline metal salt. Therefore, after humic acids have been adsorbed in a column filled with the calcium-ion-enriched tuff, a reduction of the salt concentration in the ongoing solution enhances the release of the adsorbed material. These findings show that NYT can be used for the removal of humic acids from water.     

丙烯酸改性壳聚糖磁性颗粒处理模拟废水中氨氮

以去除水产养殖废水中的氨氮，寻找安全快速高效的吸附剂为目的。以壳聚糖为原料制备丙烯酸改性壳聚糖磁性颗粒，采用单因素及正交实验方法优化制备条件，研究振荡吸附条件对吸附量的影响，进行吸附等温模型和吸附动力学研究。结果表明，最佳制备条件，丙烯酸4 mL、磁流体0.75 g、过硫酸铵1 g、戊二醛1.5 mL；最佳吸附条件，废水pH值5~9、吸附剂浓度3 g/L、吸附时间10 min；吸附过程符合二级动力学模型，以化学吸附为主；液膜扩散为限速步骤；氨氮最大吸附量为77.16 mg/g，远高于其他传统吸附剂。研究表明，丙烯酸改性壳聚糖磁性颗粒对模拟水产养殖废水的氨氮去除效果显著，具有很好的应用前景。     

腐殖酸树脂处理含Pb2+、CU2+、Ni2+废水的研究

利用泥炭为原料制备腐殖酸树脂.在动态条件下,研究了腐殖酸树脂对重金属离子Pb2+、Cu2+和Ni2+的吸附效果及吸附条件.同时探讨了腐殖酸树脂对重金属离子Pb2+、Cu2+和Ni2+的吸附与解吸再生机理,吸附机理研究表明,腐殖酸树脂对重金属离子Pb2+、Cu2+和Ni2+的主要吸附形式为离子交换吸附和络合吸附.结果表明,在废水pH值为5.0～7.0,Pb2+、Cu2+和Ni2+浓度分别为50 mg/L,经腐殖酸树脂处理,Pb2+、Cu2+和Ni2+去除率可达98%以上,且处理后废水近中性.含Pb2+、Cu2+和Ni2+电镀废水经腐殖酸树脂处理后,废水中Pb2+、Cu2+和Ni2+含量显著低于国家排放标准.     

Removal of azo dye from water by magnetite adsorption-Fenton oxidation.

The aim of this study is to highlight the possibility of using powder magnetite adsorption-Fenton oxidation as a method for removal of azo dye acid red B (ARB) from water. The adsorption properties of magnetite powder towards ARB were studied. The oxidation of adsorbed ARB and regeneration of magnetite adsorbent at the same time by Fenton reagent (hydrogen peroxide [H2O2] + iron (II) [Fe2+]) in another treatment unit with a smaller volume was also investigated. The efficiency of Fenton oxidation of ARB was compared for the reaction carried out in solution and on magnetite. The magnetic separation method was used to recover magnetite after adsorption or regeneration. The results indicated that the adsorption rate was fast. The capacity was strongly dependent on pH and inorganic anions, and pH 3.8 was optimal for the adsorption of ARB. The adsorption can be described well using the Langmuir model. The oxidation was more efficient for ARB adsorbed on magnetite than in solution. The adsorption capacity of magnetite increased significantly after regeneration, which was the result of an increase in surface area of the adsorbent and change of elemental ratio (oxygen:iron [O:Fe]) on the surface. The maximum adsorption capacity for ARB was 32.4 mg/g adsorbent.     

顶空气相色谱测试水中苯系混合物在不同材料上的吸附行为

设计了正交实验对5种材料吸附模拟废水中苯系混合物(苯、甲苯、二甲苯)的条件进行优化,CD02硅藻土与X型纳米分子筛以2∶1(质量比)进行复合后,对苯系混合物去除效果最好.采用顶空气相色谱法测定8种不同材料对水中苯系混合物的去除情况,结果表明复合材料对苯系混合物具有良好的去除效果,仅次于活性炭.复合材料在pH为7、搅拌时间为25 min、用量为1.8g/L时,对苯系混合物质量浓度为4.0 mg/L模拟废水的平均去除率为87.56％.经过4次再生后,复合材料的再生率仍高达84.90％,对苯系混合物的平均去除率为91.49％.     

Phenol removal from wastewater by adsorption on zeolitic composite

It is well known that adsorption is an efficient method of removal of various pollutants from wastewater. The present study examines the phenol removal from water by adsorption on a new material, based on zeolitic volcanic tuff. This compound contains zeolitic tuff and cellulose, another known adsorbent, in a mass ratio of 4 to 1. The performances of the new adsorbent composite were compared with those of a widely used adsorbent material, zeolitic volcanic tuff. The adsorbent properties were tested on batch synthetic solutions containing 1–10 mg L^?1 (1–10 ppm) phenol, at room temperature without pH adjustment. The influence of the adsorbent dose, pH and contact time on the removal degree of phenol from water was investigated. The experimental data were modeled using the Langmuir, Freundlich, and Temkin adsorption isotherms. The Langmuir model was found to best represent our data revealing a monolayer adsorption with a maximum adsorption capacity between 0.12 and 0.53 mg g^?1 at 25 °C, for 2.00 g of adsorbent, depending on the initial phenol concentration. The adsorption kinetic study was performed using a pseudo-first- and pseudo-second-order kinetic models illustrating that phenol adsorption on zeolite composite is well described by pseudo-first kinetic equations. Our results indicated that phenol adsorption on the new adsorbent composite is superior to that on the classic zeolite.     

改性松针对水体中铅(II)的吸附

探讨了改性松针(GXLsp)作为吸附剂对水体中铅离子的吸附性能,考察了吸附时间、溶液pH值、吸附剂用量、盐离子浓度、Pb(II)初始浓度及温度对改性松针吸附Pb(II)的影响。利用Langmuir和Freundlich等温线模型对实验数据进行非线性拟合分析,结果表明,Freundlich等温线模型能很好地描述松针对Pb(II)的吸附过程。热力学参数表明吸附是一个自发的吸热过程。改性松针对铅的吸附行为符合拟二级动力学方程,表明吸附过程是以化学吸附为主。在293K时松针对Pb(II)的饱和吸附量为318.3 mg/g,因此,GXLsp可作为一种高效低值生物质吸附剂以去除水体中重金属Pb(II)的污染。     

Efficacy of biochar in removal of organic pesticide,Bentazone from watershed systems

Abstract

Bentazone is one of the toxic insecticides used to control forest tent caterpillar moths, boll weevils, gypsy moths, and other types of moths in various field crops. We report the efficacy of biochar prepared from the Azardirachta Indica waste biomass as adsorbent for removal of Bentazone. Biochar material was prepared by pyrolysis process under limited oxygen conditions. Biochar material was characterized by proximate and ultimate analysis, SEM analysis, FTIR analysis and TG/DTA analyses. The Bentazone adsorption capacity by biochar from aqueous solutions was assessed. Effect of time, adsorbent dosage, insecticide concentration and pH on the adsorption characteristics of the biochar were evaluated. Adsorption parameters were obtained at equilibrium contact time of 150?min, with biochar dosage of 0.5?g at pH 8. From the optimization studies, desirability of 0.952 was obtained with response (adsorption uptake) of 79.40?mg/g, for initial concentration of insecticide (50?mg/L), adsorbent dosage (0.448?g), time 30.0?min and pH 2. The adsorption isotherm data for the removal of Bentazone fitted well with the Freundlich isotherm. This study indicates that the biochar produced from the bark of Azardirachta Indica biomass could be employed as a potential adsorbent for removal of synthetic organic pollutants from the water streams.     

Physical and chemical regeneration of zeolitic adsorbents for dye removal in wastewater treatment

Natural zeolite and synthetic zeolite, MCM-22, were employed as effective adsorbents for a basic dye, methylene blue, removal from wastewater. Two methods, Fenton oxidation and high temperature combustion, have been used for regeneration of used materials. It is found that MCM-22 exhibits equilibrium adsorption at 1.7 x 10(-4) mol g(-1), much higher than the adsorption of natural zeolite (5 x 10(-5) mol g(-1)) at initial dye concentration of 2.7 x 10(-5)M and 30 degrees C. Solution pH will affect the adsorption behaviour of MCM-22. Higher solution pH results in higher adsorption capacity. The regenerated adsorbents show different capacity depending on regeneration technique. Physical regeneration by high temperature combustion will be better than chemical regeneration using Fenton oxidation in producing effective adsorbents. Regeneration of MCM-22 by high temperature treatment can make the adsorbent exhibit comparable or superior adsorption capacity as compared to the fresh sample depending on the temperature and time. The optimal temperature and time will be 540 degrees C and 1h. The Fenton oxidation will recover 60% adsorption capacity. For natural zeolite, regeneration can not fully recover the adsorption capacity with the two techniques and the regenerated natural zeolites by the two techniques are similar, showing 60% adsorption capacity of fresh sample. Kinetic studies indicate that the adsorption follows pseudo-second-order kinetics.     

溴化十六烷基吡啶改性沸石对水中甲基橙的吸附

采用溴化十六烷基吡啶(CPB)对天然沸石进行改性制备得到了CPB改性沸石,通过批量吸附实验考察了CPB改性沸石对水中阴离子染料甲基橙的去除作用。结果表明,天然沸石对水中甲基橙的吸附能力很差,而CPB改性沸石则可以有效吸附去除水中的甲基橙。CPB改性沸石对水中甲基橙的吸附能力随CPB负载量的增加而增加,CPB负载量最大的改性沸石对水中甲基橙的吸附能力最强。双分子层CPB改性沸石对水中甲基橙的去除率随吸附剂投加量的增加而增加,而CPB改性沸石对水中甲基橙的单位吸附量则随吸附剂投加量的增加而降低。双分子层CPB改性沸石对水中甲基橙的吸附平衡数据可以采用Langmuir等温吸附模型加以描述。根据Langmuir模型计算得到的CPB负载量为341 mmol/(kg沸石)的双分子层CPB改性沸石对水中甲基橙的最大吸附容量为63.7 mg/g(303 K和pH 7)。准二级动力学模型适合用于描述双分子层CPB改性沸石对水中甲基橙的吸附动力学过程。pH和反应温度对双分子层CPB改性沸石吸附水中甲基橙的影响较小。以上结果说明,双分子层CPB改性沸石适合作为一种吸附剂用于去除废水中的甲基橙。     

复合改性海泡石同步处理废水中的氮磷

采用盐热和稀土掺杂制备复合改性海泡石,研究了复合改性海泡石对废水中N、P的吸附特征和去除效果。结果表明,与海泡石原矿粉比较,复合改性海泡石的脱氮除磷能力分别提高49.71%和90.14%;复合改性海泡石对N、P的吸附可以用Langmuir吸附模型描述,获得的最大吸附量分别为1.165和1.121 mg/g;修正的Elovich模型能较好地描述复合改性海泡石吸附N、P的动力学过程;用NaOH溶液可以再生吸附材料,获得较好的脱氮除磷效果,再生次数以2次为宜;用复合改性海泡石处理污水处理站的二级生化出水,最终出水的pH、N和P含量均达到《城镇污水处理厂污染物排放标准》的要求。     

Removal of nickel (II) from aqueous solutions using marine macroalgae as the sorbing biomass

In the present study biosorption technique, the passive accumulation of metals by biomass, is used for the removal of nickel from aqueous medium. The brown algae, Sargassum sp., in its natural and acid treated forms are used as a low cost sorbent. The adsorption characteristics of nickel on Sargassum sp. are evaluated as a function of time, pH, adsorbent dosage and initial concentration of nickel. The equilibrium adsorption data are fitted to Freundlich and Langmuir adsorption isotherm models and the model parameters are evaluated. Both the models represent the experimental data satisfactorily. The adsorption follows Lagergren first order kinetic model. The monolayer adsorption capacities of natural and acid treated forms of algae as obtained from Langmuir adsorption model are found to be 181 and 250mg g(-1) respectively.