Evaluating the degradation of the herbicides picloram and 2,4-D in a compartmentalized reactive biobarrier with internal liquid recirculation

Tordon is a widely used herbicide formulation of 2,4-dichlorophenoxyacetic acid (2,4-D) and 4-amino-3,5,6-trichloropicolinic acid (picloram), and it is considered a toxic herbicide. The purposes of this work were to assess the feasibility of a microbial consortium inoculated in a lab-scale compartmentalized biobarrier, to remove these herbicides, and isolate, identify, and evaluate their predominant microbial constituents. Volumetric loading rates of herbicides ranging from 31.2 to 143.9 g m^?3 day^?1, for 2,4-D, and 12.8 to 59.3 g m^?3 day^?1 for picloram were probed; however, the top operational limit of the biobarrier, detected by a decay in the removal efficiency, was not reached. At the highest loading rates probed, high average removal efficiencies of 2,4-D, 99.56?±?0.44; picloram, 94.58?±?2.62; and chemical oxygen demand (COD), 89.42?±?3.68, were obtained. It was found that the lab-scale biofilm reactor efficiently removed both herbicides at dilution rates ranging from 0.92 to 4.23 day^?1, corresponding to hydraulic retention times from 1.087 to 0.236 days. On the other hand, few microbial strains able to degrade picloram are reported in the literature. In this work, three of the nine bacterial strains isolated cometabolically degrade picloram. They were identified as Hydrocarboniphaga sp., Tsukamurella sp., and Cupriavidus sp.     

Treatment of pretreated coking wastewater by flocculation,alkali out,air stripping,and three-dimensional electrocatalytic oxidation with parallel plate electrodes

The coking wastewater generally comprises highly concentrated, recalcitrant, and toxic organic pollutants, so its treatment has been of great importance to prevent living beings and their environment from these hazardous contaminations. The treatment of pretreated coking wastewater by flocculation-coagulation, alkali out, air stripping, and three-dimensional (3-D) electrocatalytic oxidation was performed (gap between the used β-PbO₂/Ti anode and titanium cathode, 12 mm; mass ratio of Cu-Mn/granular activated carbon (GAC) to effluent, 1:4; cell voltage, 7 V). The results showed that the pH adjusting from 3.7 to 6.1 was necessary for coagulants; alkali out played an important role because it brought up precipitation containing higher fatty acids as well as other contaminants to decrease the chemical oxygen demand (COD) in the effluent, and it had also forced the reduction of ammonia nitrogen (NH₃-N) by incorporating with air stripping; for 3-D electrocatalytic oxidation with a bleaching liquid assisting, the initial pH 8.5 of effluent was suitable for Cu-Mn/GAC; moreover, it was considered that its Cu component was dedicated to the decrease of COD and NH₃-N, while the Mn component specialized in the decay of NH₃-N. The residual COD and NH₃-N values in the final effluent with pH 6.5 were 95.8 and 8.8 mg/L, respectively, demonstrating that the whole processes applied were feasible and low in cost.     

Toxicity assessment of 2,4-D and MCPA herbicides in primary culture of fish hepatic cells

In this study, we used primary cultures of fish hepatic cells as a tool for evaluating the effects of environmental contamination. Primary hepatic cell cultures derived from the subtropical fish Metynnis roosevelti were exposed to different concentrations (0.275, 2.75 and 27.5 μg L^?1) of the herbicides 2,4-dichlorophenoxyacetic acid (2,4-D) and 4-chloro-2-methylphenoxyacetic acid (MCPA). Cellular respiratory activity was evaluated by polarography using three substrates: 0.5 M glucose, 0.5 M succinate and 0.5 M α-ketoglutarate. Significant changes were observed in cellular oxygen consumption with 0.5 M α-ketoglutarate. Even at low concentrations, 2,4-D and MCPA were potent uncouplers of oxidative phosphorylation. Primary cultures of M. roosevelti liver cells may provide a useful tool for the evaluation of environmental contaminant effects. A review of regulations regarding permitted concentrations of these herbicides is needed.     

Strategies to evaluate biodegradability: application to chlorinated herbicides

The biodegradability of nitrochlorinated (diuron and atrazine) and chlorophenoxy herbicides (2,4-D and MCPA) has been studied through several bioassays using different testing times and biomass/substrate ratios. A fast biodegradability test using unacclimated activated sludge yielded no biodegradation of the herbicides in 24 h. The inherent biodegradability test gave degradation percentages of around 20–30 % for the nitrochlorinated herbicides and almost complete removal of the chlorophenoxy compounds. Long-term biodegradability assays were performed using sequencing batch reactor (SBR) and sequencing batch membrane bioreactor (SB-MBR). Fixed concentrations of each herbicide below the corresponding EC₅₀ value for activated sludge were used (30 mg L^?1 for diuron and atrazine and 50 mg L^?1 for 2,4-D and MCPA). No signs of herbicide degradation appeared before 35 days in the case of diuron and atrazine and 21 days for 2,4-D, whereas MCPA was partially degraded since the early stages. Around 25–36 % degradation of the nitrochlorinated herbicides and 53–77 % of the chlorophenoxy ones was achieved after 180 and 135 days, respectively, in SBR, whereas complete disappearance of 2,4-D was reached after 80 days in SB-MBR.     

Mixture toxicity of the antifouling compound irgarol to the marine phytoplankton species Dunaliella tertiolecta

This study examined the toxicity of irgarol, individually and in binary mixtures with three other pesticides (the fungicide chlorothalonil, and the herbicides atrazine and 2,4-D), to the marine phytoplankton species Dunaliella tertiolecta. Standard 96-h static algal bioassays were used to determine pesticide effects on population growth rate. Irgarol significantly inhibited D. tertiolecta growth rate at concentrations > or = 0.27 micro g/L. Irgarol was significantly more toxic to D. tertiolecta than the other pesticides tested (irgarol 96 h EC50 = 0.7 micro g/L; chlorothalonil 96 h EC50 = 64 micro g/L; atrazine 96 h EC50 = 69 micro g/L; 2,4-D 96 h EC50 = 45,000 micro g/L). Irgarol in mixture with chlorothalonil exhibited synergistic toxicity to D. tertiolecta, with the mixture being approximately 1.5 times more toxic than the individual compounds. Irgarol and atrazine, both triazine herbicides, were additive in mixture. The toxicity threshold of 2,4-D was much greater than typical environmental levels and would not be expected to influence irgarol toxicity. Based on these interactions, overlap of certain pesticide applications in the coastal zone may increase the toxicological risk to resident phytoplankton populations.     

Dicamba and 2,4-D residues following applicator cleanout: A potential point source to the environment and worker exposure

This paper presents a survey of pesticide residues in tanks following application and throughout the cleanout procedure as conducted by 46 volunteer operators across Colorado. While many pesticides were detected, this paper focuses on dicamba and 2,4-D, which were detected by liquid chromatography/tandem mass spectroscopy (LC-MS/MS). An exponential decrease in concentration was observed with sequential rinses, although this decrease may be more rapid for more water-soluble pesticides. More than 95% of the pesticide in the prerinse solution was removed by the end of the third rinse in all but three operator samples. Concentrations after three rinses were 0.41 ± 0.25 and 3.3 ± 1.1 mg/L for dicamba and 2,4-D, respectively. These concentrations suggest that the recommended practice of three rinses may not be adequate to eliminate off-target effects or point sources of pesticide waste, and that the recommended standard of personal protective equipment is essential to prevent worker exposure to the chemicals.

Implications:?This paper demonstrates that the waste generated during cleanout of pesticide application devices constitutes a potential source of pollution and worker exposure. In particular, while the first rinse of pesticide containers is often treated as hazardous waste and reapplied to crops, the remaining rinses are not. This work demonstrates that the wastewater generated in subsequent rinses can have high enough concentrations to impact worker health, cause off-target effects on crops, and potentially constitute a point source of pesticides. The practical implication is for improved recommendations and regulations regarding pesticide applicators and their cleanout process.     

Atmospheric concentrations and dry and wet deposits of some herbicides currently used on the Canadian Prairies

High volume air sampling in the Canadian Prairies was used to characterize atmospheric concentrations for 10 herbicides (alachlor, atrazine, ethalfluralin, metolachlor, 2,4-D, dicamba, bromoxynil, MCPA, trifluralin, and triallate) along a 500-km north-south transect. Atmospheric concentration measurements at various altitudes identified that of the six herbicides present in the highest concentrations, triallate was strongly influenced by local sources, while 2,4-D, dicamba, bromoxynil, MCPA and trifluralin were dominated by regional atmospheric transport. Concentrations of the herbicides measured at various altitudes were compared with dry deposition rates measured using a dry/wet deposition sampler and used to calculate deposition velocities V(d). The primary atmospheric transport mechanism for MCPA and bromoxynil was shown to be adsorption to particles dispersed in the atmosphere, with the same mechanism also confirmed for 2,4-D and dicamba, while trifluralin was shown to be transported mainly in the gas phase. This method of calculation indicated that transportation of triallate was influenced by particle adsorption. Weekly maximum atmospheric loadings of the major herbicides present in the Prairies were estimated to range from 73 kg for trifluralin to 541 kg for 2,4-D.     

Utilization of long duration high-volume sampling coupled to SPME-GC-MS/MS for the assessment of airborne pesticides variability in an urban area (Strasbourg,France) during agricultural application

Atmospheric samples have been collected between 14 March and 12 September 2012 on a 2-week basis (15 days of sampling and exchange of traps each 7 days) in Strasbourg (east of France) for the analysis of 43 pesticides. Samples (particle and gas phases) were separately extracted using Accelerated Solvent Extraction (ASE) and pre-concentrated by Solid Phase Micro-Extraction (SPME) before analysis by gas chromatography coupled to tandem mass spectrometry (GC-MS/MS). Four SPME consecutive injections at distinct temperatures were made in order to increase the sensitivity of detection for the all monitored pesticides. Currently used detected pesticides can be grouped in four classes; those used in maize crops (acetochlor, benoxacor, dicamba, s-metolachlor, pendimethalin, and bromoxynil), in cereal crops (benoxacor, chlorothalonil, fenpropimorph, and propiconazole), in vineyards (tebuconazole), and as herbicides for orchards, meadows of green spaces (2,4-MCPA, trichlopyr). This is in accordance with the diversity of crops found in the Alsace region and trends observed are in accordance with the period of application of these pesticides. Variations observed permit also to demonstrate that the long time sampling duration used in this study is efficient to visualize temporal variations of airborne pesticides concentrations. Then, long time high-volume sampling could be a simple method permitting atmospheric survey of atmospheric contamination without any long analysis time and consequently low cost.     

Electrochemical degradation of chlorophenoxy and chlorobenzoic herbicides in acidic aqueous medium by the peroxi-coagulation method

The degradation of 4-chlorophenoxyacetic acid (4-CPA), 4-chloro-2-methylphenoxyacetic acid (MCPA), 2,4-dichlorophenoxyacetic acid (2,4-D) and 2,4,5-trichlorophenoxyacetic acid (2,4,5-T) as chlorophenoxy herbicides, as well as of 3,6-dichloro-2-methoxybenzoic acid (dicamba) as chlorobenzoic herbicide, has been studied by peroxi-coagulation. This electrochemical method yields a very effective depollution of all compounds in acidic aqueous medium of pH 3.0 working under pH regulation, since they are oxidized with hydroxyl radicals produced from Fenton's reaction between Fe(2+) and H(2)O(2) generated by the corresponding Fe anode and O(2)-diffusion cathode. Their products can then be removed by mineralization or coagulation with the Fe(OH)(3) precipitate formed. Both degradative paths compete at low currents, but coagulation predominates at high currents. The peroxi-coagulation process of dicamba at I>or=300 mA leads to more than 90% of coagulation, being much more efficient than its comparative electro-Fenton treatment with a Pt anode and 1 mM Fe(2+), where only mineralization takes place. For the chlorophenoxy compounds, electro-Fenton gives a slightly lower depollution than peroxi-coagulation, because more easily oxidable products are produced. Oxidation of chlorinated products during peroxi-coagulation is accompanied by the release of chloride ion to the solution. The efficiency of this method decreases with increasing electrolysis time and current. The decay of all herbicides follows a pseudo-first-order reaction, with a similar constant rate for 4-CPA, MCPA, 2,4-D and 2,4,5-T, and a higher value for dicamba.     

Herbicide levels in rivers draining two prairie agricultural watersheds (1984)

A monitoring survey was conducted during 1984 on the Ochre and Turtle Rivers, which flow into Dauphin Lake in western Manitoba, Canada, to determine levels of the herbicides MCPA, diclofop-methyl, dicamba, bromoxynil, 2,4-D, triallate and trifluralin which were widely used in each watershed. Triallate concentrations exceeded 4 ng/L in 50% and 10% of the 21 samples taken from each of the Turtle and Ochre River, respectively, during the period March to October 1984. Trifluralin concentrations exceeded 3 ng/L in 14% and 10% of the samples from the respective rivers. Maximum concentrations did not exceed 25 ng/L and were unrelated to changes in river flow. Bromoxynil and diclofop were detected in the Turtle River, at concentrations of 113 and 476 ng/L, respectively, following a major high water event in late June, but were undetectable (less than 2 and 12 ng/L, respectively) at other sampling times. Dicamba and 2,4-D were detectable throughout most of the sampling period in both rivers at low levels (less than 100 ng/L). High levels of dicamba and 2,4-D (5476 and 2568 ng/L respectively) were found in water from the Turtle River prior to the high water event event possibly caused by spraying of ditches or rights-of-way near the river. Discharges (grams/year) of all seven herbicides monitored in the study represented less than 0.1% of the amounts estimated to be used in each watershed. Unit loadings (mg/ha/year) of 2,4-D and dicamba were similar to those reported for Southern Ontario streams in the mid-1970's. The results indicate that herbicide contamination of Manitoba streams draining agricultural areas is generally low except when major runoff occurs during the application period in May and June.     

Mixture Toxicity of the Antifouling Compound Irgarol to the Marine Phytoplankton Species Dunaliella tertiolecta

This study examined the toxicity of irgarol, individually and in binary mixtures with three other pesticides (the fungicide chlorothalonil, and the herbicides atrazine and 2,4-D), to the marine phytoplankton species Dunaliella tertiolecta. Standard 96-h static algal bioassays were used to determine pesticide effects on population growth rate. Irgarol significantly inhibited D. tertiolecta growth rate at concentrations ≥ 0.27 μ g/L. Irgarol was significantly more toxic to D. tertiolecta than the other pesticides tested (irgarol 96 h EC₅₀ = 0.7 μ g/L; chlorothalonil 96 h EC₅₀ = 64 μ g/L; atrazine 96 h EC₅₀ = 69 μ g/L; 2,4-D 96 h EC₅₀ = 45,000 μ g/L). Irgarol in mixture with chlorothalonil exhibited synergistic toxicity to D. tertiolecta, with the mixture being approximately 1.5 times more toxic than the individual compounds. Irgarol and atrazine, both triazine herbicides, were additive in mixture. The toxicity threshold of 2,4-D was much greater than typical environmental levels and would not be expected to influence irgarol toxicity. Based on these interactions, overlap of certain pesticide applications in the coastal zone may increase the toxicological risk to resident phytoplankton populations.     

Procedure for the determination of 2,4-D and dicamba in inhalation, dermal, hand-wash, and urine samples from spray applicators

Analytical procedures for the simultaneous determination of residues of 2,4-D and dicamba from polyurethane foam plug air samplers, ethylene glycol impregnated glass-fiber filter paper dermal samplers, 1% sodium bicarbonate hand wash solution, and urine are presented. Residues were derivatized with diazomethane and quantitated using electron capture gas chromatography. Recoveries were greater than 80% at the limit of detection in all substrates. The limits of detection for both herbicides were 0.1 microgram/foam plug and 0.5 micrograms/filter paper, and in the urine, 1.7 micrograms/100 mL and 5.0 micrograms/100 mL for dicamba and 2,4-D, respectively.     

Electrocoagulation-integrated hybrid membrane processes for the treatment of tannery wastewater

Three different combinations of treatment techniques, i.e. electrocoagulation combined with microfiltration (EMR), membrane bioreactor (MBR) and electrocoagulation integrated with membrane bioreactor (hybrid MBR, (HMBR)), were analysed and compared for the treatment of tannery wastewater operated for 7 days under the constant trans-membrane pressure of 5 kPa. HMBR was found to be most suitable in performance as well as fouling reduction, with 94 % of chemical oxygen demand (COD) removal, 100 % chromium removal and 8 % improvement in percentage reduction in permeate flux compared to MBR with only 90 % COD removal and 67 % chromium removal. The effect of mixed liquor suspended solids on fouling was also investigated and was found to be insignificant. EMR was capable of elevating the flux but was not as efficient as HMBR and MBR in COD removal. Fouling reduction by HMBR was further confirmed by SEM-EDX and particle size analysis.     

Simultaneous nitrification and denitrification with anoxic phosphorus uptake in a membrane bioreactor system.

The performance of an innovative membrane bioreactor (MBR) process using anoxic phosphorus uptake with nitrification and denitrification for the treatment of municipal wastewater with respect to operational performance and effluent quality is addressed in this paper. The system was operated at steady-state conditions with a synthetic acetate-based wastewater at a hydraulic retention time (HRT) of 12 hours and on degritted municipal wastewater at a total system HRT of 6 hours. The MBR system was able to achieve 99% biochemical oxygen demand (BOD), chemical oxygen demand (COD), and ammonia-nitrogen (NH4(+)-N); 98% total Kjeldahl nitrogen (TKN); and 97% phosphorus removal, producing effluent BOD, COD, NH4+-N, TKN, nitrate-nitrogen, nitrite-nitrogen, and phosphate-phosphorus of <3, 14, 0.2, 0.26, 5.8, 0.21, and <0.01 mg/L, respectively, at the 6-hour HRT. The comparison of the synthetic and municipal wastewater run is presented in this paper. Steady-state mass balance on municipal wastewater was performed to reveal some key features of the modified MBR system.     

Decolorization does not always mean detoxification: case study of a newly isolated Pseudomonas peli for decolorization of textile wastewater

The textile industry is a favor to the Tunisian economy by offering several job positions. However, it’s not environmentally friendly. In fact, textile industries discharge high volumes of wastewater which contain several toxic pollutants such as dyes, fixator, and whiteness. In our study, Pseudomonas peli, isolated and characterized from Oued Hamdoun (center of Tunisia), was found able to decolorize textile effluent about 81 % after 24 h shaking incubation. On the other hand, the in vitro antiproliferative effects of the untreated and treated effluent was evaluated by their potential cytotoxic activity using the MTT colorimetric method against three human cancer cell lines (A549, lung cell carcinoma; HT29, colon adenocarcinoma; and MCF7, breast adenocarcinoma). Results showed that intact textile effluent and its content azo dyes didn’t inhibit the proliferation of all tested cell lines. However, the cytotoxic effect was remarkable when we tested effluent obtained after treatment by P. peli in a dose-dependent manner. This activity was attributed to the presence, in our treated effluent, of some azo products of dyes which are responsible for inhibition of human cell lines proliferation. Thus, the use of this strain for testing on the industrial scale seems impossible and disadvantageous.     

Monitoring of toxicity during degradation of selected pesticides using ionizing radiation

The optimization of experimental conditions for radiolytic removal of organic pollutants from water and waste with the use of ionizing radiation via controlling the concentration of target compound(s) requires also monitoring the toxicity changes during the process. Commonly used herbicides 2,4-D and dicamba were shown to increase toxicity measured with the Microtox test at low irradiation doses resulting from formation of more toxic transient products, which can be decomposed at larger doses. The changes of toxicity were examined with respect to dose magnitude and the presence of commonly occurring scavengers of radiation.     

Coagulant recovery from water treatment plant sludge and reuse in post-treatment of UASB reactor effluent treating municipal wastewater

In the present study, feasibility of recovering the coagulant from water treatment plant sludge with sulphuric acid and reusing it in post-treatment of upflow anaerobic sludge blanket (UASB) reactor effluent treating municipal wastewater were studied. The optimum conditions for coagulant recovery from water treatment plant sludge were investigated using response surface methodology (RSM). Sludge obtained from plants that use polyaluminium chloride (PACl) and alum coagulant was utilised for the study. Effect of three variables, pH, solid content and mixing time was studied using a Box–Behnken statistical experimental design. RSM model was developed based on the experimental aluminium recovery, and the response plots were developed. Results of the study showed significant effects of all the three variables and their interactions in the recovery process. The optimum aluminium recovery of 73.26 and 62.73 % from PACl sludge and alum sludge, respectively, was obtained at pH of 2.0, solid content of 0.5 % and mixing time of 30 min. The recovered coagulant solution had elevated concentrations of certain metals and chemical oxygen demand (COD) which raised concern about its reuse potential in water treatment. Hence, the coagulant recovered from PACl sludge was reused as coagulant for post-treatment of UASB reactor effluent treating municipal wastewater. The recovered coagulant gave 71 % COD, 80 % turbidity, 89 % phosphate, 77 % suspended solids and 99.5 % total coliform removal at 25 mg Al/L. Fresh PACl also gave similar performance but at higher dose of 40 mg Al/L. The results suggest that coagulant can be recovered from water treatment plant sludge and can be used to treat UASB reactor effluent treating municipal wastewater which can reduce the consumption of fresh coagulant in wastewater treatment.     

Performance investigation of membrane bioreactor systems during municipal wastewater reclamation.

Four commercially available membrane bioreactor (MBR) systems were operated at the pilot scale, to investigate performance during the reclamation of municipal wastewater. The MBR performance was evaluated under a variety of operating conditions, including two types of feed wastewater (raw and advanced primary effluent), hydraulic retention times (HRTs) ranging from 2 to 6 hours, and permeate fluxes between 20 and 41 lmh. Test results showed that MBR systems were capable of operating on advanced primary effluent, despite the possible presence of coagulant and/or polymer residual, with minimal membrane fouling. Membrane performance data generated during this study was also used to quantify the relationship between permeate flux and membrane fouling. Cleaning intervals at various flux conditions were estimated as follows: 69 days at 20 lmh, 58 days at 25 lmh, and 30 days for operation between 31 and 41 lmh. It was also demonstrated that the MBR process could be optimized to operate with minimal fouling under high hydraulic (flux = 37 lmh) and organic loading (HRT = 2 hours and food-to-microorganism ratio = 0.33 g COD/g VSS x d) conditions. Water quality monitoring conducted throughout the study showed that each MBR system consistently produced an oxidized (5-day biochemical oxygen demand < 2 mg/L) and nitrified (ammonia < 1 mg-N/L) effluent low in particulate matter (turbidity < 0.1 NTU), under all conditions tested.     

Membrane bioreactor treatment of commonly used organophosphate pesticides

Five pesticide formulations registered for use in Canada containing organophosphate-insecticide active ingredients azinphos-methyl, chlorpyrifos, diazinon, malathion and phorate were subjected to treatment by membrane bioreactor (MBR) technology. The target active ingredients were introduced to the MBR at ppm level concentrations. The biodegradation of these compounds was analyzed daily using selected ion monitoring gas chromatography-mass spectrometry (GC/MS-SIM) following extraction of the analytes using solid-phase extraction (SPE). Amounts measuring 83 % to 98 % of the target analytes were removed with steady-state concentrations being reached within 5 days of their introduction. The dissolved oxygen, temperature, pH, and total heterotrophic bacterial population were monitored daily to ensure optimal conditions for biodegradation. The quality of the effluent from the MBR was assessed daily through spectrophotometric methods. Measurements were conducted for the concentration of ammonia, nitrate, nitrite, total and reactive phosphorus, as well as the chemical oxygen demand (COD) of the effluent. This study demonstrated that the MBR technology is feasible and efficient for treatment of organophosphate pesticides without introducing additional chemical additives.     

Soil column experiments used as a means to assess transport,sorption, and biodegradation of pesticides in groundwater

Soil column experiments are used to investigate the fate of three pesticides of high, intermediate, and low solubility in groundwater: N- phosphonomethyl glycine (glyphosate); O,O-diethyl-S-[(ethylthio)methyl]phosphorodithioate (phorate); (2,4-dichlorophenoxy)acetic acid (2,4-D). Feed solutions are prepared by adding each pesticide (100 mg/L glyphosate, 50 μ g/L phorate, 50 mg/L 2,4-D) along with conservative tracer, KBr, in synthetic groundwater. The concentration of the pesticides in effluents is detected by ion chromatography (glyphosate, 2,4-D) and GC-FID (phorate). The Br^? breakthrough curves are employed to estimate the dispersion coefficient and mean pore velocity in each column. Solute transport and reactive models accounting for equilibrium/non-equilibrium sorption and biodegradation are coupled with inverse modeling numerical codes to estimate the kinetic parameters for all pesticides.