Effects of improved spatial and temporal modeling of on-road vehicle emissions

Numerous emission and air quality modeling studies have suggested the need to accurately characterize the spatial and temporal variations in on-road vehicle emissions. The purpose of this study was to quantify the impact that using detailed traffic activity data has on emission estimates used to model air quality impacts. The on-road vehicle emissions are estimated by multiplying the vehicle miles traveled (VMT) by the fleet-average emission factors determined by road link and hour of day. Changes in the fraction of VMT from heavy-duty diesel vehicles (HDDVs) can have a significant impact on estimated fleet-average emissions because the emission factors for HDDV nitrogen oxides (NOx) and particulate matter (PM) are much higher than those for light-duty gas vehicles (LDGVs). Through detailed road link-level on-road vehicle emission modeling, this work investigated two scenarios for better characterizing mobile source emissions: (1) improved spatial and temporal variation of vehicle type fractions, and (2) use of Motor Vehicle Emission Simulator (MOVES2010) instead of MOBILE6 exhaust emission factors. Emissions were estimated for the Detroit and Atlanta metropolitan areas for summer and winter episodes. The VMT mix scenario demonstrated the importance of better characterizing HDDV activity by time of day, day of week, and road type. More HDDV activity occurs on restricted access road types on weekdays and at nonpeak times, compared to light-duty vehicles, resulting in 5-15% higher NOx and PM emission rates during the weekdays and 15-40% lower rates on weekend days. Use of MOVES2010 exhaust emission factors resulted in increases of more than 50% in NOx and PM for both HDDVs and LDGVs, relative to MOBILE6. Because LDGV PM emissions have been shown to increase with lower temperatures, the most dramatic increase from MOBILE6 to MOVES2010 emission rates occurred for PM2.5 from LDGVs that increased 500% during colder wintertime conditions found in Detroit, the northernmost city modeled.     

A more accurate method using MOVES (Motor Vehicle Emission Simulator) to estimate emission burden for regional-level analysis

The U.S. Environmental Protection Agency’s (EPA) Motor Vehicle Emission Simulator (MOVES) is required by the EPA to replace Mobile 6 as an official on-road emission model. Incorporated with annual vehicle mile traveled (VMT) by Highways Performance Monitoring System (HPMS) vehicle class, MOVES allocates VMT from HPMS to MOVES source (vehicle) types and calculates emission burden by MOVES source type. However, the calculated running emission burden by MOVES source type may be deviated from the actual emission burden because of MOVES source population, specifically the population fraction by MOVES source type in HPMS vehicle class. The deviation is also the result of the use of the universal set of parameters, i.e., relative mileage accumulation rate (relativeMAR), packaged in MOVES default database. This paper presents a novel approach by adjusting the relativeMAR to eliminate the impact of MOVES source population on running exhaust emission and to keep start and evaporative emissions unchanged for both MOVES2010b and MOVES2014. Results from MOVES runs using this approach indicated significant improvements on VMT distribution and emission burden estimation for each MOVES source type. The deviation of VMT by MOVES source type is minimized by using this approach from 12% to less than 0.05% for MOVES2010b and from 50% to less than 0.2% for MOVES2014 except for MOVES source type 53. Source type 53 still remains about 30% variation. The improvement of VMT distribution results in the elimination of emission burden deviation for each MOVES source type. For MOVES2010b, the deviation of emission burdens decreases from ?12% for particulate matter less than 2.5 μm (PM_2.5) and ?9% for carbon monoxide (CO) to less than 0.002%. For MOVES2014, it drops from 80% for CO and 97% for PM_2.5 to 0.006%.

Implications: This approach is developed to more accurately estimate the total emission burdens using EPA’s MOVES, both MOVES2010b and MOVES2014, by redistributing vehicle mile traveled (VMT) by Highways Performance Monitoring System (HPMS) class to MOVES source type on the basis of comprehensive traffic study, local link-by-link VMT broken down into MOVES source type.     

Hot emission model for mobile sources: application to the metropolitan region of the city of Santiago, Chile

Depending on the final application, several methodologies for traffic emission estimation have been developed. Emission estimation based on total miles traveled or other average factors is a sufficient approach only for extended areas such as national or worldwide areas. For road emission control and strategies design, microscale analysis based on real-world emission estimations is often required. This involves actual driving behavior and emission factors of the local vehicle fleet under study. This paper reports on a microscale model for hot road emissions and its application to the metropolitan region of the city of Santiago, Chile. The methodology considers the street-by-street hot emission estimation with its temporal and spatial distribution. The input data come from experimental emission factors based on local driving patterns and traffic surveys of traffic flows for different vehicle categories. The methodology developed is able to estimate hourly hot road CO, total unburned hydrocarbons (THCs), particulate matter (PM), and NO(x) emissions for predefined day types and vehicle categories.     

Development of operating mode distributions for different types of roadways under different congestion levels for vehicle emission assessment using MOVES

The Motor Vehicle Emission Simulator (MOVES) quantifies emissions as a function of vehicle modal activities. Hence, the vehicle operating mode distribution is the most vital input for running MOVES at the project level. The preparation of operating mode distributions requires significant efforts with respect to data collection and processing. This study is to develop operating mode distributions for both freeway and arterial facilities under different traffic conditions. For this purpose, in this study, we (1) collected/processed geographic information system (GIS) data, (2) developed a model of CO₂ emissions and congestion from observations, (3) implemented the model to evaluate potential emission changes from a hypothetical roadway accident scenario. This study presents a framework by which practitioners can assess emission levels in the development of different strategies for traffic management and congestion mitigation.

Implications: This paper prepared the primary input, that is, the operating mode ID distribution, required for running MOVES and developed models for estimating emissions for different types of roadways under different congestion levels. The results of this study will provide transportation planners or environmental analysts with the methods for qualitatively assessing the air quality impacts of different transportation operation and demand management strategies.     

Real-world fuel use and gaseous emission rates for flex fuel vehicles operated on E85 versus gasoline

Flex fuel vehicles (FFVs) typically operate on gasoline or E85, an 85%/15% volume blend of ethanol and gasoline. Differences in FFV fuel use and tailpipe emission rates are quantified for E85 versus gasoline based on real-world measurements of five FFVs with a portable emissions measurement system (PEMS), supplemented chassis dynamometer data, and estimates from the Motor Vehicle Emission Simulator (MOVES) model. Because of inter-vehicle variability, an individual FFV may have higher nitrogen oxide (NO_x) or carbon monoxide (CO) emission rates on E85 versus gasoline, even though average rates are lower. Based on PEMS data, the comparison of tailpipe emission rates for E85 versus gasoline is sensitive to vehicle-specific power (VSP). For example, although CO emission rates are lower for all VSP modes, they are proportionally lowest at higher VSP. Driving cycles with high power demand are more advantageous with respect to CO emissions, but less advantageous for NO_x. Chassis dynamometer data are available for 121 FFVs at 50,000 useful life miles. Based on the dynamometer data, the average difference in tailpipe emissions for E85 versus gasoline is ?23% for NO_x, ?30% for CO, and no significant difference for hydrocarbons (HC). To account for both the fuel cycle and tailpipe emissions from the vehicle, a life cycle inventory was conducted. Although tailpipe NO_x emissions are lower for E85 versus gasoline for FFVs and thus benefit areas where the vehicles operate, the life cycle NO_x emissions are higher because the NO_x emissions generated during fuel production are higher. The fuel production emissions take place typically in rural areas. Although there are not significant differences in the total HC emissions, there are differences in HC speciation. The net effect of lower tailpipe NO_x emissions and differences in HC speciation on ozone formation should be further evaluated.

Implications: Reported comparisons of flex fuel vehicle (FFV) tailpipe emission rates for E85 versus gasoline have been inconsistent. To date, this is the most comprehensive evaluation of available and new data. The large range of inter-vehicle variability illustrates why prior studies based on small sample sizes led to apparently contradictory findings. E85 leads to significant reductions in tailpipe nitrogen oxide (NO_x) and carbon monoxide (CO) emission rates compared with gasoline, indicating a potential benefit for ozone air quality management in NO_x-limited areas. The comparison of FFV tailpipe emissions between E85 and gasoline is sensitive to power demand and driving cycles.     

机动车污染排放模型研究综述

过去几十年,为了掌握机动车污染排放的规律和特征,向决策者提供科学有效的机动车污染控制措施,研究者们致力于研究机动车污染物排放的物化原理和影响机动车污染的主要因素,并据此建立多种尺度的机动车排放模型,以模拟城市区域或者街道的污染物排放.为了分析机动车的瞬态排放特征,目前的机动车排放模型研究正逐渐从宏观向微观发展,排放测试方法注重获取逐秒的排放数据,排放模型模拟的时间尺度和空间尺度逐步趋向微观.此外,机动车模型研究正趋向与交通模型进行耦合,从而揭示机动车在实际道路交通流中的排放特征.从机动车排放的主要影响因素、机动车排放测试、机动车排放因子模型及机动车排放清单等4个方面综述了国内外机动车排放研究现状和发展动向,对比并评价各种机动车排放模型方法的优缺点和适用范围,对我国的机动车排放模型发展方向进行了展望.     

Road grade estimation for on-road vehicle emissions modeling using light detection and ranging data

Vehicle-specific power (VSP) is useful for explaining a substantial portion of variability in real-world vehicle emissions, such as those measured with portable emissions monitoring systems (PEMS). VSP is a function of vehicle speed, acceleration, and road grade. Road grade is shown to significantly affect estimates of both VSP and of real-world emissions via sensitivity analysis and analysis of empirical data. However, road grade is difficult to measure reliably using PEMS. Therefore, alternative methods for estimating road grade were identified and compared. A preferred method for estimating road grade was explored in more detail based on light detection and ranging (LIDAR) data. The method includes buffering LIDAR data onto roadway maps using a geographic information system tool, defining segments of roadway based on criteria pertaining to vertical curvature, quantification of roadway elevations within the buffered segments, and estimation of road grade and banking by fitting a plane to each segment. Factors influencing errors in road grade estimates are discussed. The method was evaluated by application to selected interstate highways and comparison to design drawing data. The development and application of LIDAR-based road grade data are demonstrated via a case study using PEMS data collected in the Research Triangle Park, NC, area. LIDAR data are shown to be reliable and accurate for road grade estimation for vehicle emissions modeling.     

Comparison of the MOVES2010a,MOBILE6.2, and EMFAC2007 mobile source emission models with on-road traffic tunnel and remote sensing measurements

The Desert Research Institute conducted an on-road mobile source emission study at a traffic tunnel in Van Nuys, California, in August 2010 to measure fleet-averaged, fuel-based emission factors. The study also included remote sensing device (RSD) measurements by the University of Denver of 13,000 vehicles near the tunnel. The tunnel and RSD fleet-averaged emission factors were compared in blind fashion with the corresponding modeled factors calculated by ENVIRON International Corporation using U.S. Environmental Protection Agency's (EPA's) MOVES2010a (Motor Vehicle Emissions Simulator) and MOBILE6.2 mobile source emission models, and California Air Resources Board's (CARB's) EMFAC2007 (EMission FACtors) emission model. With some exceptions, the fleet-averaged tunnel, RSD, and modeled carbon monoxide (CO) and oxide of nitrogen (NO_x) emission factors were in reasonable agreement (±25%). The nonmethane hydrocarbon (NMHC) emission factors (specifically the running evaporative emissions) predicted by MOVES were insensitive to ambient temperature as compared with the tunnel measurements and the MOBILE- and EMFAC-predicted emission factors, resulting in underestimation of the measured NMHC/NO_x ratios at higher ambient temperatures. Although predicted NMHC/NO_x ratios are in good agreement with the measured ratios during cooler sampling periods, the measured NMHC/NO_x ratios are 3.1, 1.7, and 1.4 times higher than those predicted by the MOVES, MOBILE, and EMFAC models, respectively, during high-temperature periods. Although the MOVES NO_x emission factors were generally higher than the measured factors, most differences were not significant considering the variations in the modeled factors using alternative vehicle operating cycles to represent the driving conditions in the tunnel. The three models predicted large differences in NO_x and particle emissions and in the relative contributions of diesel and gasoline vehicles to total NO_x and particulate carbon (TC) emissions in the tunnel.

Implications: Although advances have been made to mobile source emission models over the past two decades, the evidence that mobile source emissions of carbon monoxide and hydrocarbons in urban areas were underestimated by as much as a factor of 2–3 in past inventories underscores the need for on-going verification of emission inventories. Results suggest that there is an overall increase in motor vehicle NMHC emissions on hot days that is not fully accounted for by the emission models. Hot temperatures and concomitant higher ratios of NMHC emissions relative to NO_x both contribute to more rapid and efficient formation of ozone. Also, the ability of EPA's MOVES model to simulate varying vehicle operating modes places increased importance on the choice of operating modes to evaluate project-level emissions.     

Modeling cold soak evaporative vapor emissions from gasoline-powered automobiles using a newly developed method

ABSTRACT

Volatile organic compounds (VOCs) evaporate and vent from a vehicle’s fuel tank to its evaporative control system when the vehicle is both driven and parked. VOCs making it past the control system are emissions. Driving and parking activity, fuel volatility, and temperature strongly affect vapor generation and the effectiveness of control technologies, and the wide variability in these factors and the sensitivity of emissions to these factors make it difficult to estimate evaporative emissions at the macro level. Established modeling methods, such as COPERT and MOVES, estimate evaporative emissions by assuming a constant in-use canister condition and consequently contain critical uncertainty when real conditions deviate from that standard condition. In this study, we have developed a new method to model canister capacity as a representative variable, and estimated emissions for all parking events based on semi-empirical functions derived from real-world activity data and laboratory measurements. As compared to chamber measurements collected during this study, the bias of the MOVES diurnal tank venting simulation ranges from ?100% to 129%, while the bias for our method’s simulation is 1.4% to 8.5%. Our modeling method is compared to the COPERT and MOVES models by estimating evaporative emissions from a Euro-3/4/5 and a Tier 2 vehicle in conditions representative for Chicago, IL, and Guangzhou, China. Estimates using the COPERT and MOVES methods differ from our method by ?56% to 120% and ?100% to 25%, respectively. The study highlights the importance for continued modeling improvement of the anthropogenic evaporative emission inventory and for tightened regulatory standards.

Implications: The COPERT and MOVES methodologies contain large uncertainties for estimating evaporative emissions, while our modeling method is developed based on chamber measurements to estimate evaporative emissions and can properly address those uncertainties. Modeling results suggested an urgent need to complete evaporative emissions inventories and also indicated that tightening evaporative emission standards is urgently needed, especially for warm areas.     

Understanding the emission impacts of high-occupancy vehicle (HOV) to high-occupancy toll (HOT) lane conversions: Experience from Atlanta,Georgia

Converting a congested high-occupancy vehicle (HOV) lane into a high-occupancy toll (HOT) lane is a viable option for improving travel time reliability for carpools and buses that use the managed lane. However, the emission impacts of HOV-to-HOT conversions are not well understood. The lack of emission impact quantification for HOT conversions creates a policy challenge for agencies making transportation funding choices. The goal of this paper is to evaluate the case study of before-and-after changes in vehicle emissions for the Atlanta, Georgia, I-85 HOV/HOT lane conversion project, implemented in October 2011. The analyses employed the Motor Vehicle Emission Simulator (MOVES) for project-level analysis with monitored changes in vehicle activity data collected by Georgia Tech researchers for the Georgia Department of Transportation (GDOT). During the quarterly field data collection from 2010 to 2012, more than 1.5 million license plates were observed and matched to vehicle class and age information using the vehicle registration database. The study also utilized the 20-sec, lane-specific traffic operations data from the Georgia NaviGAtor intelligent transportation system, as well as a direct feed of HOT lane usage data from the State Road and Tollway Authority (SRTA) managed lane system. As such, the analyses in this paper simultaneously assessed the impacts associated with changes in traffic volumes, on-road operating conditions, and fleet composition before and after the conversion. Both greenhouse gases and criteria pollutants were examined.

Implications: A straight before-after analysis showed about 5% decrease in air pollutants and carbon dioxide (CO₂). However, when the before-after calendar year of analysis was held constant (to account for the effect of 1 yr of fleet turnover), mass emissions at the analysis site during peak hours increased by as much as 17%, with little change in CO₂. Further investigation revealed that a large percentage decrease in criteria pollutants in the straight before-after analysis was associated with a single calendar year change in MOVES. Hence, the Atlanta, Georgia, results suggest that an HOV-to-HOT conversion project may have increased mass emissions on the corridor. The results also showcase the importance of obtaining on-road data for emission impact assessment of HOV-to-HOT conversion projects.     

Development of a Speciated,Hourly, and Gridded Air Pollutants Emission Modeling System—A Case Study on the Precursors of Photochemical Smog in the Seoul Metropolitan Area,Korea

ABSTRACT

A speciated, hourly, and gridded air pollutants emission modeling system (SHEMS) was developed and applied in predicting hourly nitrogen dioxide (NO₂) and ozone (O₃) levels in the Seoul Metropolitan Area (SMA). The primary goal of the SHEMS was to produce a systemized emission inventory for air pollutants including ozone precursors for modeling air quality in urban areas.

The SHEMS is principally composed of three parts: (1) a pre-processor to process emission factors, activity levels, and spatial and temporal information using a geographical information system; (2) an emission model for each source type; and (3) a post-processor to produce report and input data for air quality models through database modeling. The source categories in SHEMS are point, area, mobile, natural, and other sources such as fugitive emissions. The emission database produced by SHEMS contains 22 inventoried compounds: sulfur dioxide, NO₂, carbon monoxide, and 19 speciated volatile organic compounds. To validate SHEMS, the emission data were tested with the Urban Airshed Model to predict NO₂ and O₃ concentrations in the SMA during selected episode days in 1994. The results turned out to be reliable in describing temporal variation and spatial distribution of those pollutants.     

CAREAIR: A Computer Aided Modeling Toolbox to Generate and Analyze Emission Data in High Temporal and Spatial Resolution

ABSTRACT

For the evaluation of air quality improvement strategies, emission data in high temporal and spatial resolution is necessary, including all emission sources and all relevant pollutant species. Computer aided models are usually used to generate this emission data because it is not possible to obtain measurements from all sources, and, furthermore, a large amount of data has to be handled. For the development of emission modeling systems, a software tool called CAREAIR has been created. The intention of this paper is to introduce CAREAIR to the international community dealing with emission inventories and air quality improvement strategies.

CAREAIR is not just a single emission model but a flexible modeling toolbox. The database contains data and formulas for data manipulation, which is performed by using a set of flexible operators with different specifications. The emission calculation is carried out by combining several data manipulation operators. The CAREAIR modeling toolbox allows model implementation for the calculation of emissions from different pollutants in a high spatial and temporal resolution. The application of CAREAIR within various investigation projects in Germany, Europe, and Nigeria shows that CAREAIR is an appropriate instrument for the development of flexible emission models by meeting the various demands of these projects. The function and the data structures of this modeling toolbox are described and, towards the end of the paper, an example of an emission calculation with CAREAIR is given.     

Radical precursors and related species from traffic as observed and modeled at an urban highway junction

Nitrous acid (HONO) and formaldehyde (HCHO) are important precursors for radicals and are believed to favor ozone formation significantly. Traffic emission data for both compounds are scarce and mostly outdated. A better knowledge of today's HCHO and HONO emissions related to traffic is needed to refine air quality models. Here the authors report results from continuous ambient air measurements taken at a highway junction in Houston, Texas, from July 15 to October 15, 2009. The observational data were compared with emission estimates from currently available mobile emission models (MOBILE6; MOVES [MOtor Vehicle Emission Simulator]). Observations indicated a molar carbon monoxide (CO) versus nitrogen oxides (NO_x) ratio of 6.01 ± 0.15 (r ² = 0.91), which is in agreement with other field studies. Both MOBILE6 and MOVES overestimate this emission ratio by 92% and 24%, respectively. For HCHO/CO, an overall slope of 3.14 ± 0.14 g HCHO/kg CO was observed. Whereas MOBILE6 largely underestimates this ratio by 77%, MOVES calculates somewhat higher HCHO/CO ratios (1.87) than MOBILE6, but is still significantly lower than the observed ratio. MOVES shows high HCHO/CO ratios during the early morning hours due to heavy-duty diesel off-network emissions. The differences of the modeled CO/NO_x and HCHO/CO ratios are largely due to higher NO_x and HCHO emissions in MOVES (30% and 57%, respectively, increased from MOBILE6 for 2009), as CO emissions were about the same in both models. The observed HONO/NO_x emission ratio is around 0.017 ± 0.0009 kg HONO/kg NO_x which is twice as high as in MOVES. The observed NO₂/NO_x emission ratio is around 0.16 ± 0.01 kg NO₂/kg NO_x, which is a bit more than 50% higher than in MOVES. MOVES overestimates the CO/CO₂ emission ratio by a factor of 3 compared with the observations, which is 0.0033 ± 0.0002 kg CO/kg CO₂. This as well as CO/NO_x overestimation is coming from light-duty gasoline vehicles.

Implications: Nitrous acid (HONO) and formaldehyde (HCHO) are important precursors for radicals that ultimately contribute to ozone formation. There still exist uncertainties in emission sources of HONO and HCHO and thus regional air quality modeling still tend to underestimate concentrations of free radicals in the atmosphere. This paper demonstrates that the latest U.S. Environmental Protection Agency (EPA) traffic emission model MOVES still shows significant deviations from observed emission ratios, in particular underestimation of HCHO/CO and HONO/NO_x ratios. Improving the performance of MOVES may improve regional air quality modeling.     

Development of a speciated, hourly, and gridded air pollutants emission modeling system--a case study on the precursors of photochemical smog in the Seoul metropolitan area, Korea

A speciated, hourly, and gridded air pollutants emission modeling system (SHEMS) was developed and applied in predicting hourly nitrogen dioxide (NO2) and ozone (O3) levels in the Seoul Metropolitan Area (SMA). The primary goal of the SHEMS was to produce a systemized emission inventory for air pollutants including ozone precursors for modeling air quality in urban areas. The SHEMS is principally composed of three parts: (1) a pre-processor to process emission factors, activity levels, and spatial and temporal information using a geographical information system; (2) an emission model for each source type; and (3) a post-processor to produce report and input data for air quality models through database modeling. The source categories in SHEMS are point, area, mobile, natural, and other sources such as fugitive emissions. The emission database produced by SHEMS contains 22 inventoried compounds: sulfur dioxide, NO2, carbon monoxide, and 19 speciated volatile organic compounds. To validate SHEMS, the emission data were tested with the Urban Airshed Model to predict NO2 and O3 concentrations in the SMA during selected episode days in 1994. The results turned out to be reliable in describing temporal variation and spatial distribution of those pollutants.     

Particulate matter speciation profiles for light-duty gasoline vehicles in the United States

Representative profiles for particulate matter particles less than or equal to 2.5 µm (PM_2.5) are developed from the Kansas City Light-Duty Vehicle Emissions Study for use in the U.S. Environmental Protection Agency (EPA) vehicle emission model, the Motor Vehicle Emission Simulator (MOVES), and for inclusion in the EPA SPECIATE database for speciation profiles. The profiles are compatible with the inputs of current photochemical air quality models, including the Community Multiscale Air Quality Aerosol Module Version 6 (AE6). The composition of light-duty gasoline PM_2.5 emissions differs significantly between cold start and hot stabilized running emissions, and between older and newer vehicles, reflecting both impacts of aging/deterioration and changes in vehicle technology. Fleet-average PM_2.5 profiles are estimated for cold start and hot stabilized running emission processes. Fleet-average profiles are calculated to include emissions from deteriorated high-emitting vehicles that are expected to continue to contribute disproportionately to the fleet-wide PM_2.5 emissions into the future. The profiles are calculated using a weighted average of the PM_2.5 composition according to the contribution of PM_2.5 emissions from each class of vehicles in the on-road gasoline fleet in the Kansas City Metropolitan Statistical Area. The paper introduces methods to exclude insignificant measurements, correct for organic carbon positive artifact, and control for contamination from the testing infrastructure in developing speciation profiles. The uncertainty of the PM_2.5 species fraction in each profile is quantified using sampling survey analysis methods. The primary use of the profiles is to develop PM_2.5 emissions inventories for the United States, but the profiles may also be used in source apportionment, atmospheric modeling, and exposure assessment, and as a basis for light-duty gasoline emission profiles for countries with limited data.

Implications: PM_2.5 speciation profiles were developed from a large sample of light-duty gasoline vehicles tested in the Kansas City area. Separate PM_2.5 profiles represent cold start and hot stabilized running emission processes to distinguish important differences in chemical composition. Statistical analysis was used to construct profiles that represent PM_2.5 emissions from the U.S. vehicle fleet based on vehicles tested from the 2005 calendar year Kansas City metropolitan area. The profiles have been incorporated into the EPA MOVES emissions model, as well as the EPA SPECIATE database, to improve emission inventories and provide the PM_2.5 chemical characterization needed by CMAQv5.0 for atmospheric chemistry modeling.     

Developing a high-resolution vehicular emission inventory by integrating an emission model and a traffic model: Part 1--Modeling fuel consumption and emissions based on speed and vehicle-specific power

To improve the accuracy and applicability of vehicular emission models, this study proposes a speed and vehicle-specific power (VSP) modeling method to estimate vehicular emissions and fuel consumption using data gathered by a portable emissions monitoring system (PEMS). The PEMS data were categorized into discrete speed-VSP bins on the basis of the characteristics of vehicle driving conditions and emissions in Chinese cities. Speed-VSP modal average rates of emissions (or fuel consumption) and the time spent in the corresponding speed-VSP bins were then used to calculate the total trip emissions (or fuel consumption) and emission factors (or fuel economy) under specific average link speeds. The model approach was validated by comparing it against measured data with prediction errors within 20% for trip emissions and link-speed-based emission factors. This analysis is based on the data of light-duty gasoline vehicles in China; however, this research approach could be generalized to other vehicle fleets in other countries. This modeling method could also be coupled with traffic demand models to establish high-resolution emissions inventories and evaluate the impacts of traffic-related emission control measures.     

Emission inventory for the road transport sector in Sardinia (Italy)

Atmospheric emission inventories are important tools for studying air quality and to set up possible remediation plans in areas characterised by nonattainment of the limit values established by legislation. In industrialised countries a considerable fraction of the emissions is due to road traffic, in particular in urban areas. For this reason emissions from road traffic must be estimated as accurately as possible, a task that can be performed, for the European vehicle fleet, thanks to the availability of the COPERT III methodology. This methodology is powerful and accurate, even if its algorithms can be difficult to apply in a regional emission inventory; moreover the collection of the necessary input data requires a lot of resources and time. This paper describes the road traffic emission inventory estimated for Region Sardinia (Italy) with a bottom-up approach. The estimation has been done by means of a software tool (EMITRA—EMIssions from road TRAnsport) which implements the COPERT III methodology. The resulting emission inventory has been compared against another emission inventory for Sardinia and against emission inventories for other Italian regions, to evaluate its reliability.     

Daily Variability of Motor Vehicle Emissions Derived from Traffic Counter Data

ABSTRACT

This work studied the daily variability of mobile sources in rural and urban areas, in and around the Atlanta Metropolitan Area. Traffic counter data collected during the 1992 Southern Oxidants Study Atlanta Intensive Study were used to analyze the spatial and temporal distribution of traffic volume. A simple method to study the daily variability of mobile emissions from the different types of urban and rural roads is presented. The method is based on hourly traffic volume data and emission factors and it has been generalized to describe the daily variability of mobile emissions for urban and rural areas and for the whole modeling domain. Implications of this study for improving mobile emission inventories are also discussed.     

Improved Spatial Allocation Methodology for On-Road Mobile Emissions

ABSTRACT

Emissions from automobiles and trucks operating on public roads represent a major portion of the air pollutants included in emission inventories. When emission data are prepared for air quality modeling studies, such as those supporting development of a State Implementation Plan, an emission processor matches the spatial and temporal resolution of the emissions to the requirements of the modeling study. However, the spatial location of vehicular emissions is not known and must be estimated. This paper presents a methodology for determining the spatial distribution of the roads belonging to a road class using geospatial data functions, such as those commonly provided by a geographic information system. Vehicle-miles traveled (VMT) are then allocated to medium-resolution (12 x 12-km) and fine-resolution (4 x 4-km) modeling grids using both this methodology and the existing top-down methodology, which uses population density. The results show a significant difference in the spatial distribution of VMT between these two methodologies. Based upon these results, we recommend using the road class-specific methodology in lieu of the population methodology for spatially allocating vehicular emissions for medium- and finer-resolution modeling grids.